Stenner Pumps Classic Series Manual

TO BE INSTALLED AND MAINTAINED BY PROPERLY TRAINED
PROFESSIONAL INSTALLER ONLY. READ MANUAL & LABELS
FOR ALL SAFETY INFORMATION & INSTRUCTIONS.
WARNING
CLASSIC SERIES
INSTALLATION AND MAINTENANCE MANUAL
PERISTALTIC METERING PUMPS SINCE 1957

www.stenner.com
2
TABLE OF CONTENTS
WARRANTY AND SERVICE POLICY............................................ 3
SAFETY INFORMATION ................. 4-11, 14-17, 19-23, 26, 27, 30, 34
OUTPUTS ........................................................................ 6-11
MATERIALS OF CONSTRUCTION............................................. 12
ACCESSORIES .................................................................... 13
INSTALLATION ................................................................ 14-22
TROUBLESHOOTING ........................................................ 23-26
TUBE REPLACEMENT ....................................................... 27-33
CLEANING THE POINT OF INJECTION.................................. 34-36
MOTOR – EXPLODED VIEW AND PARTS ............................... 37-40
FEED RATE CONTROL – EXPLODED VIEW AND PARTS ............ 41-42
PUMP HEAD – EXPLODED VIEW AND PARTS ........................ 43-46
PUMP TUBES ..................................................................... 47
CHECK VALVES ................................................................... 48
FOR YOUR RECORDS ........................................................... 49
IMCL 120418b

USA and Canada 800.683.2378, International 904.641.1666
WARRANTY AND CUSTOMER SERVICE
LIMITED WARRANTY
Stenner Pump Company will for a period of one (1) year from the date of purchase (proof
of purchase required) repair or replace – at our option – all defective parts. Stenner is not
responsible for any removal or installation costs. Pump tube assemblies and rubber
components are considered perishable and are not covered in this warranty. Pump tube
will be replaced each time a pump is in for service, unless otherwise specified. The cost of
the pump tube replacement will be the responsibility of the customer. Stenner will incur
shipping costs for warranty products shipped from our factory in Jacksonville, Florida. Any
tampering with major components, chemical damage, faulty wiring, weather conditions,
water damage, power surges, or products not used with reasonable care and maintained in
accordance with the instructions will void the warranty. Stenner limits its liability solely to
the cost of the original product. We make no other warranty expressed or implied.
RETURNS
Stenner offers a 30-day return policy on factory direct purchases. Except as otherwise
provided, no merchandise will be accepted for return after 30 days from purchase. To
return merchandise at any time, call Stenner at 800.683.2378 for a Return Merchandise
Authorization (RMA) number. A 15% re-stocking fee will be applied. Include a copy of your
invoice or packing slip with your return.
DAMAGED OR LOST SHIPMENTS
All truck shipments: Check your order immediately upon arrival. All damage must be noted
on the delivery receipt. Call Stenner Customer Service at 800.683.2378 for all shortages
and damages within seven (7) days of receipt.
SERVICE & REPAIRS
Before returning a pump for warranty or repair, remove chemical from pump tube by
running water through the tube, and then run the pump dry. Following expiration of the
warranty period, Stenner Pump Company will clean and overhaul any Stenner metering
pump for a minimum labor charge plus necessary replacement parts and shipping. All
metering pumps received for overhaul will be restored to their original condition. The
customer will be charged for missing parts unless specific instructions are given. To return
merchandise for repair, call Stenner at 800.683.2378 or 904.641.1666 for a Return
Merchandise Authorization (RMA) number.
DISCLAIMER
The information contained in this manual is not intended for specific application purposes.
Stenner Pump Company reserves the right to make changes to prices, products, and
specifications at any time without prior notice.
TRADEMARKS
QuickPro®is a registered trademark of the Stenner Pump Company.
Santoprene®is a registered trademark of Exxon Mobil Corporation.
Versilon®is a registered trademark of Saint-Gobain Performance Plastics.
Pellethane®is a registered trademark of Lubrizol Advanced Materials, Inc.
AquaShield™is a trademark of Houghton International.
3

www.stenner.com
4
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
Warns about hazards that CAN cause death, serious personal
injury, or property damage if ignored.
ELECTRIC SHOCK HAZARD
ELECTRIC SHOCK HAZARD
Pump supplied with grounding power cord and attached plug. To reduce risk of
electrical shock, connect only to a properly grounded, grounding type receptacle.
Install only on a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI).
DANGER DE CHOC ÉLECTRIQUE
La pompe est dotée d’un cordon d’alimentation avec mise à la terre muni d'une
fiche. Pour réduire le risque de choc électrique, branchez uniquement sur une prise
correctement mise à la terre. Installez uniquement sur un circuit protégé par un
disjoncteur différentiel.
DO NOT alter the power cord or plug end.
DO NOT use receptacle adapters.
DO NOT use pump with a damaged or altered power cord or plug. Contact the
factory or an authorized service facility for repair.
HAZARDOUS VOLTAGE
DISCONNECT power cord before removing motor cover for service. Electrical service
by trained personnel only.
EXPLOSION HAZARD
This equipment IS NOT explosion proof. DO NOT install or operate in an
explosive environment.
RISK OF CHEMICAL EXPOSURE
Potential for chemical burns, fire, explosion, personal injury, or property damage. To
reduce risk of exposure, the use of proper personal protective equipment is mandatory.
RISK OF FIRE HAZARD
DO NOT install or operate on any flammable surface.
RISK OF CHEMICAL OVERDOSE
To reduce risk, follow proper installation methods and recommendations. Check your
local codes for additional guidelines.
To reduce the risk of injury, do not permit children to use this
product. This appliance is not to be used by persons with reduced physical, sensory
or mental capabilities, or lack of experience or knowledge, unless they have been
given supervision or instruction.

USA and Canada 800.683.2378, International 904.641.1666 5
SAFETY INFORMATION continued
Warns about hazards that WILL or CAN cause minor personal
injury or property damage if ignored.
PLUMBING
Chemical feed pump installation must always adhere to your local plumbing codes
and requirements. Be sure installation does not constitute a cross connection. Check
local plumbing codes for guidelines.
NOTICE: Indicates special instructions or general mandatory action.
This metering pump is portable and designed to be removable from the plumbing
system without damage to the connections.
Before installing or servicing the pump, read the pump manual for all safety
information and complete instructions. The pump is designed for installation and
service by properly trained personnel.
Installation of product must adhere to all regulatory and compliance codes
applicable to the area.
This metering pump and its components have been tested for use with the following
chemicals: Sodium Hypochlorite (10-15%), Muriatic Acid (20-22 Baume, 31.5% HCl),
and Soda Ash.
Cette pompe de dosage et ses composants ont été testés pour leur compatibilité
avec les produits chimiques suivants : hypochlorite de sodium (10 à 15 %), acide
chlorhydrique (20 à 22 % Baume, 31,5 % HCl), et carbonate de sodium.
This metering pump is certified by WQA for use with Water and Sodium Hypochlorite 15%.
This is the safety alert symbol. When displayed in this manual or on the
equipment, look for one of the following signal words alerting you to the
potential for personal injury or property damage.
PUMP SUITABLE FOR USE OUTDOORS when installed with a Stenner Rain Roof Part
No. MP90000.
Electrical installation should adhere to all national and local codes. Consult a
licensed professional for assistance with proper electrical installation.
Removing power from pool/spa recirculation pump must also remove power from pump.
The use of an auxiliary safety device (not supplied), such as a flow switch or sensor,
is recommended to prevent feed pump operation in the event of a recirculation
pump failure or if flow is not sensed.
Point of chemical injection should be beyond all pumps, filters, and heaters.
Suitable for indoor and outdoor use.
Adaptée à une utilisation aussi bien à l’intérieur qu’à l’extérieur.
SAVE THESE INSTRUCTIONS

Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
45MHP2* 45MJH1 100 / 6.9
45M1 45MJL1 25 / 1.7
45MHP10* 45MJH2 100 / 6.9
45M2 45MJL2 25 / 1.7
45MHP22* 45MJH7 100 / 6.9 7
45M3 45MJL3 25 / 1.7 3
45M4 45MJL4 25 / 1.7 4 1.7 3.5 7.0 10.5 14.0 17.5 21.0 24.5 28.0 31.5 35.0
45M5 45MJL5 25 / 1.7 5 2.5 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0
www.stenner.com
6
CLASSIC 45 – FLOW RATE OUTPUTS
NOTICE: The information within this chart is solely intended for use as a guide.The output data is an approximation based on
pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump
Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.
*Injection check valve is included with pump rated 100 psi (6.9 bar) maximum.
Single Head Adjustable – Gallons per Day
2 0.5 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
1 0.2 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0
1.1 2.2 4.4 6.6 8.8 11.0 13.2 15.4 17.6 19.8 22.0
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
45MHP2* 45MJH1 100 / 6.9
45M1 45MJL1 25 / 1.7
45MHP10* 45MJH2 100 / 6.9
45M2 45MJL2 25 / 1.7
45MHP22* 45MJH7 100 / 6.9 7
45M3 45MJL3 25 / 1.7 3
45M4 45MJL4 25 / 1.7 4 5.1 10.6 21.2 31.8 42.4 53.0 63.6 74.2 84.8 95.4 106.0
45M5 45MJL5 25 / 1.7 5 7.6 15.1 30.3 45.4 60.6 75.7 90.8 106.0 121.1 136.3 151.4
Single Head Adjustable – Liters per Day
2 1.5 3.0 6.1 9.1 12.1 15.1 18.2 21.2 24.2 27.3 30.3
Single Head Fixed – Gallons & Liters per Day
Model Item Number Maximum Pump gpd @ 60Hz lpd @ 50Hz
Prefix psi / bar Tube
45MPHP2* 45MFH1 100 / 6.9
45MP1 45MFL1 25 / 1.7
45MPHP10* 45MFH2 100 / 6.9
45MP2 45MFL2 25 / 1.7
45MPHP22* 45MFH7 100 / 6.9 7
45MP3 45MFL3 25 / 1.7 3
45MP4 45MLF4 25 / 1.7 4 35.0 106.0
45MP5 45MLF5 25 / 1.7 5 50.0 151.4
1 3.0 9.1
1 0.6 0.9 1.8 2.7 3.6 4.5 5.5 6.4 7.3 8.2 9.1
3.3 6.6 13.3 20.0 26.6 33.3 40.0 46.6 53.3 60.0 66.6
2 10.0 30.3
22.0 66.6
Approximate Outputs @ 60Hz
Approximate Outputs @ 50Hz
Approximate Outputs @ 60 & 50Hz

Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
85MHP5* 85MJH1 100 / 6.9 1
85M1 85MJL1 25 / 1.7
85MHP17* 85MJH2 100 / 6.9
85M2 85MJL2 25 / 1.7
85MHP40* 85MJH7 100 / 6.9 7
85M3 85MJL3 25 / 1.7 3
85M4 85MJL4 25 / 1.7 4 3.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0
85M5 85MJL5 25 / 1.7 5 4.3 8.5 17.0 25.5 34.0 42.5 51.0 59.5 68.0 76.5 85.0
1 0.3 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
USA and Canada 800.683.2378, International 904.641.1666 7
CLASSIC 85 – FLOW RATE OUTPUTS
NOTICE: The information within this chart is solely intended for use as a guide.The output data is an approximation based on
pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump
Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.
*Injection check valve is included with pump rated 100 psi (6.9 bar) maximum.
Single Head Adjustable – Gallons per Day
2 0.8 1.7 3.4 5.1 6.8 8.5 10.2 11.9 13.6 15.3 17.0
Single Head Adjustable – Liters per Day
Single Head Fixed – Gallons & Liters per Day
1
Model Item Number Maximum Pump gpd @ 60Hz lpd @ 50Hz
Prefix psi / bar Tube
85MPHP5* 85MFH1 100 / 6.9
85MP1 85MFL1 25 / 1.7
85MPHP17* 85MFH2 100 / 6.9
85MP2 85MFL2 25 / 1.7
85MPHP40* 85MFH7 100 / 6.9 7
85MP3 85MFL3 25 / 1.7 3
85MP4 85MFL4 25 / 1.7 4 60.0 181.7
85MP5 85MFL5 25 / 1.7 5 85.0 257.4
1 5.0 15.1
2 17.0 51.5
40.0 121.1
2 0.8 1.7 3.4 5.1 6.8 8.5 10.2 11.9 13.6 15.3 17.0
2.0 4.0 8.0 12.0 16.0 20.0 24.0 28.0 32.0 36.0 40.0
Approximate Outputs @ 60Hz
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
85MHP5* 85MJH1 100 / 6.9
85M1 85MJL1 25 / 1.7
85MHP17* 85MJH2 100 / 6.9
85M2 85MJL2 25 / 1.7
85MHP40* 85MJH7 100 / 6.9 7
85M3 85MJL3 25 / 1.7 3
85M4 85MJL4 25 / 1.7 4 9.1 18.2 36.3 54.5 76.7 90.8 109.0 127.2 145.3 163.5 181.7
85M5 85MJL5 25 / 1.7 5 13.0 25.7 51.5 77.2 103.0 128.7 154.4 180.0 205.9 231.6 257.4
1 0.9 1.5 3.0 4.5 6.1 7.6 9.1 10.6 12.1 13.6 15.1
6.1 12.1 24.2 36.3 48.5 60.6 76.7 84.8 96.9 109.0 121.1
2 2.4 5.1 10.3 15.4 20.6 25.7 30.9 36.0 41.2 46.3 51.5
Approximate Outputs @ 50Hz
Approximate Outputs @ 60 & 50Hz

www.stenner.com
8
NOTICE: The information within this chart is solely intended for use as a guide.The output data is an approximation based on
pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump
Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.
*Injection check valve is included with pump rated 100 psi (6.9 bar) maximum.
CLASSIC 100 – FLOW RATE OUTPUTS
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L 1 2 3 4 5 6 7 8 9 10
100DMHP5* 100JH1 100 / 6.9 1 0.2 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7
100DM1 100JL1 25 / 1.7
100DMHP20* 100JH2 100 / 6.9
100DM2 100JL2 25 / 1.7
100DM3 100JL3 25 / 1.7 3 2.2 4.4 8.8 13.2 17.6 22.0 26.4 30.8 35.2 39.6 44.0
100DM4 100JL4 25 / 1.7 4 3.5 7.0 14.0 21.0 28.0 35.0 42.0 49.0 56.0 63.0 70.0
100DM5 100JL5 25 / 1.7 5 5.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0
Double Head Adjustable – Gallons per Day
1
2 1.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
1 0.3 0.6 1.2 1.8 2.4 3.0 3.6 4.2 4.8 5.4 6.0
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
100DMHP5* 100JH1 100 / 6.9
100DM1 100JL1 25 / 1.7
100DMHP20* 100JH2 100 / 6.9
100DM2 100JL2 25 / 1.7
100DM3 100JL3 25 / 1.7 3 6.7 13.3 26.7 40.0 53.3 66.6 79.9 93.3 106.6 119.9 133.2
100DM4 100JL4 25 / 1.7 4 10.6 21.2 42.4 63.6 84.8 106.0 127.2 148.4 169.6 190.8 212.0
100DM5 100JL5 25 / 1.7 5 15.1 30.3 60.6 90.8 121.1 151.4 181.7 212.0 242.2 272.5 302.8
Double Head Adjustable – Liters per Day
2 3.0 6.1 12.1 18.2 24.2 30.3 36.4 42.4 48.5 54.5 60.6
1 0.9 1.8 3.6 5.5 7.3 9.1 10.9 12.7 14.5 16.4 18.2
Double Head Fixed – Gallons & Liters per Day
Model Item Number Maximum Pump gpd @ 60Hz lpd @ 50Hz
Prefix psi / bar Tube
100DMPHP5* 100FH1 100 / 6.9
100DMP1 100FL1 25 / 1.7
100DMPHP20* 100FH2 100 / 6.9
100DMP2 100FL2 25 / 1.7
100DMP3 100FL3 25 / 1.7 3 44.0 133.2
100DMP4 100FL4 25 / 1.7 4 70.0 212.0
100DMP5 100FL5 25 / 1.7 5 100.0 302.8
1 6.0 18.2
2 20.0 60.6
Approximate Outputs @ 50Hz
Approximate Outputs @ 60Hz
Approximate Outputs @ 60 & 50Hz

USA and Canada 800.683.2378, International 904.641.1666 9
CLASSIC 170 – FLOW RATE OUTPUTS
NOTICE: The information within this chart is solely intended for use as a guide.The output data is an approximation based on
pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump
Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.
*Injection check valve is included with pump rated 100 psi (6.9 bar) maximum.
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
170DMHP9* 170JH1 100 / 6.9
170DM1 170JL1 25 / 1.7
170DMHP34* 170JH2 100 / 6.9
170DM2 170JL2 25 / 1.7
170DM3 170JL3 25 / 1.7 3 4.0 8.0 16.0 24.0 32.0 40.0 48.0 56.0 64.0 72.0 80.0
170DM4 170JL4 25 / 1.7 4 6.0 12.0 24.0 36.0 48.0 60.0 72.0 84.0 96.0 108.0 120.0
170DM5 170JL5 25 / 1.7 5 8.5 17.0 34.0 51.0 68.0 85.0 102.0 119.0 136.0 153.0 170.0
Double Head Adjustable – Gallons per Day
2 1.7 3.4 6.0 9.5 13.6 17.0 20.4 23.8 27.2 30.6 34.0
1 0.5 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
170DMHP9* 170JH1 100 / 6.9 1
170DM1 170JL1 25 / 1.7
170DMHP34* 170JH2 100 / 6.9
170DM2 170JL2 25 / 1.7
170DM3 170JL3 25 / 1.7 3 12.1 24.2 48.5 72.7 96.9 121.1 145.4 169.6 193.8 218.0 242.2
170DM4 170JL4 25 / 1.7 4 18.2 36.3 72.7 109.0 145.3 181.7 218.0 254.4 290.7 327.0 363.4
170DM5 170JL5 25 / 1.7 5 25.7 51.5 86.0 154.4 205.9 257.4 308.9 360.4 411.8 463.3 514.8
Double Head Adjustable – Liters per Day
2 5.1 10.3 18.2 28.8 39.1 51.5 61.8 72.1 82.4 92.7 102.6
Double Head Fixed – Gallons & Liters per Day
Model Item Number Maximum Pump gpd @ 60Hz lpd @ 50Hz
Prefix psi / bar Tube
170DMPHP9* 170FH1 100 / 6.9
170DMP1 170FL1 25 / 1.7
170DMPHP34* 170FH2 100 / 6.9
170DMP2 170FL2 25 / 1.7
170DMP3 170FL3 25 / 1.7 3 80.0 242.2
170DMP4 170FL4 25 / 1.7 4 120.0 363.4
170DMP5 170FL5 25 / 1.7 5 170.0 514.8
2 34.0 102.6
1 1.5 3.0 6.1 9.1 12.1 15.1 18.2 21.2 24.2 27.3 30.3
1 10.0 30.3
Approximate Outputs @ 60 & 50Hz
Approximate Outputs @ 50Hz
Approximate Outputs @ 60Hz

www.stenner.com
10
CLASSIC 100 DUAL CONTROL –
FLOW RATE OUTPUTS
NOTICE: The information within this chart is solely intended for use as a guide.The output data is an approximation based on
pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump
Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.
*Injection check valve included with pumps rated 100 psi (6.9 bar) maximum.
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L 1 2 3 4 5 6 7 8 9 10
100MDCHP5* 100DH1 100 / 6.9
100MDC1 100DL1 25 / 1.7
100MDCHP20* 100DH2 100 / 6.9
100MDC2 100DL2 25 / 1.7
100MDC3 100DL3 25 / 1.7 3 1.1 2.2 4.4 6.6 8.8 11.0 13.2 15.4 17.6 19.8 22.0
100MDC4 100DL4 25 / 1.7 4 1.7 3.5 7.0 10.5 14.0 17.5 21.0 24.5 28.0 31.5 35.0
100MDC5 100DL5 25 / 1.7 5 2.5 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0
Innermost Pump Head – Gallons per Day
2 0.5 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
1 0.2 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
100MDCHP5* 100DH1 100 / 6.9
100MDC1 100DL1 25 / 1.7
100MDCHP20* 100DH2 100 / 6.9
100MDC2 100DL2 25 / 1.7
100MDC3 100DL3 25 / 1.7 3 3.3 6.6 13.3 20.0 26.6 33.3 40.0 46.6 53.3 60.0 66.6
100MDC4 100DL4 25 / 1.7 4 5.1 10.6 21.2 31.8 42.4 53.0 63.6 74.2 84.8 95.4 106.0
100MDC5 100DL5 25 / 1.7 5 7.6 15.1 30.3 45.4 60.6 75.7 90.8 106.0 121.1136.3 151.4
Innermost Pump Head – Liters per Day
2 1.5 3.0 6.1 9.1 12.1 15.1 18.2 21.2 24.2 27.3 30.3
1 0.6 0.9 1.8 2.7 3.6 4.5 5.5 6.4 7.3 8.2 9.1
DETERMINE FLOW RATE OUTPUTS FOR EACH PUMP HEAD
Use the innermost pump head flow rate outputs to determine the output for each pump head.
Both feed rate controls (FRC) on setting 10 = maximum flow rate capacity of the pump.
Innermost Pump Head
L=5%, 1-10 = approx. 10% of maximum innermost output
Outermost Pump Head
Outermost Output = (Outermost FRC Setting %) x (Innermost Output)
Example
100MDC5 with Innermost FRC setting on 4
1. Innermost FRC setting 4 = 20 gpd
2. If outermost FRC is set on 3, then outermost output is 30% of innermost output; 0.3 x 20 gpd = 6 gpd
3. Outermost = 6 gpd, Innermost = 20 gpd, Total Pump Output = 26 gpd
Approximate Outputs @ 50Hz
Approximate Outputs @ 60Hz

USA and Canada 800.683.2378, International 904.641.1666 11
CLASSIC 170 DUAL CONTROL –
FLOW RATE OUTPUTS
NOTICE: The information within this chart is solely intended for use as a guide.The output data is an approximation based on
pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump
Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.
*Injection check valve included with pumps rated 100 psi (6.9 bar) maximum.
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L 1 2 3 4 5 6 7 8 9 10
170MDCHP9* 170DH1 100 / 6.9
170MDC1 170DL1 25 / 1.7
170MDCHP34* 170DH2 100 / 6.9
170MDC2 170DL2 25 / 1.7
170MDC3 170DL3 25 / 1.7 3 2.0 4.0 8.0 12.0 16.0 20.0 24.0 28.0 32.0 36.0 40.0
170MDC4 170DL4 25 / 1.7 4 3.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0
170MDC5 170DL5 25 / 1.7 5 4.3 8.5 17.0 25.5 34.0 42.5 51.0 59.5 68.0 76.5 85.0
Innermost Pump Head – Gallons per Day
2 0.8 1.7 3.4 5.1 6.8 8.5 10.2 11.9 13.6 15.3 17.0
1 0.3 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Model Item Number Maximum Pump Feed Rate Control Setting
Prefix psi / bar Tube L12345678910
170MDCHP9* 170DH1 100 / 6.9
170MDC1 170DL1 25 / 1.7
170MDCHP34* 170DH2 100 / 6.9
170MDC2 170DL2 25 / 1.7
170MDC3 170DL3 25 / 1.7 3 6.1 12.1 24.2 36.3 48.5 60.6 76.7 84.8 96.9 109.0 121.1
170MDC4 170DL4 25 / 1.7 4 9.1 18.2 36.3 54.5 76.7 90.8 109.0 127.2 145.3163.5 181.7
170MDC5 170DL5 25 / 1.7 5 13.0 25.7 51.5 77.2 103.0 128.7154.4 180.0 205.9231.6 257.4
Innermost Pump Head – Liters per Day
2 2.4 5.1 10.3 15.4 20.6 25.7 30.9 36.0 41.2 46.3 51.5
1 0.9 1.5 3.0 4.5 6.1 7.6 9.1 10.6 12.1 13.6 15.1
Approximate Outputs @ 60Hz
Approximate Outputs @ 50Hz

www.stenner.com
12
MATERIALS OF CONSTRUCTION
All Housings
Polycarbonate
Pump Tube
Santoprene®, FDA approved or Versilon®
Check Valve Duckbill
Santoprene®, FDA approved or Pellethane®
Suction/Discharge Tubing & Ferrules
Polyethylene, FDA approved
Suction Line Strainer and Cap
PVC or Polypropylene, NSF listed, with Ceramic Weight
All Fasteners
Stainless Steel
Tube and Injection Fittings
PVC or Polypropylene, NSF listed
Connecting Nuts 1/4", 3/8" and 3/8" Adapter
PVC or Polypropylene, NSF listed
Pump Head Latches
Polypropylene *

USA and Canada 800.683.2378, International 904.641.1666 13
ACCESSORIES
3 Connecting Nuts 1/4" or 3/8"
3 Ferrules 1/4" or 6 mm Europe
1 Injection Fitting 25 psi (1.7 bar) max. or 1 injection check valve 100 psi (6.9 bar) max.
1 Weighted Suction Line Strainer 1/4", 3/8" or 6 mm Europe
1 20' Roll of Suction/Discharge Tubing
1/4" or 3/8" White or UV Black or 6 mm White Europe
1 Additional Pump Tube
2 Additional Latches
1 Mounting Bracket
1 Manual
*Double head pumps include an additional set of the accessories listed above.

www.stenner.com
14
INSTALLATION
ADDITIONAL SAFETY INSTRUCTIONS
NOTICE: Indicates special instructions or general mandatory action.
Read all safety hazards before installing or servicing the pump. The pump is
designed for installation and service by properly trained personnel.
Use all required personal protective equipment when working on or near a chemical
metering pump.
Install the pump so that it is in compliance with all national and local plumbing
and electrical codes.
Use the proper product to treat potable water systems, use only chemicals listed or
approved for use.
Install the pump to work in conjunction with pool, spa, well pump, or system controls.
Inspect tube frequently for leakage, deterioration, or wear. Schedule a regular pump
tube maintenance change to prevent chemical damage to pump and/or spillage.
Mount pump vertically and use spill recovery to run chemical back to tank in the
event of tube failure.
Pump is not recommended for installation in areas where leakage can cause
personal injury or property damage.

USA and Canada 800.683.2378, International 904.641.1666 15
INSTALLATION continued
MOUNT PUMP
Select a dry location (to avoid water intrusion and pump damage) above the
solution tank. Best recommended location is above the solution tank in a vertical
position with the pump head pointed downward and the spill recovery (see page 18)
in place to reduce the risk and severity of damage.
To prevent pump damage in the event of a pump tube leak, never mount the pump
vertically with the pump head up.
To avoid chemical damage from fumes, DO NOT mount pump directly over an open
solution tank. Keep tank covered.
Avoid flooded suction or pump mounted lower than the solution container. Draw
solution from the top of the tank. Pump can run dry without damage. If pump is
installed with a flooded suction, a shut-off valve or other device must be provided
to stop flow to pump during service.
1. Use the mounting bracket as a template
to drill pilot holes in mounting location.
2. Secure bracket with fasteners or wall
anchors. Slide pump into bracket.
Provide 8" clearance to allow pump
orientation to be reversed during tube
replacement. DO NOT allow water
intrusion into the motor or corrosion
and damage will occur.
To prevent motor damage, verify
with a volt meter that the receptacle
voltage corresponds with the
pump voltage.
3. Plug cord into receptacle and turn the
motor power switch on. If the pump is
adjustable, turn the dial ring to 10.
4. Activate the pump by the pump control (flow switch, pressure switch, etc.) and verify
rotation of the roller assembly within the clear pump head. Turn pump switch off.
Rain Roof
(optional)
slips into
wall bracket.
Wall Bracket
Pump Head

www.stenner.com
16
INSTALLATION continued
ADDITIONAL INSTRUCTIONS FOR CE PUMPS WHEN APPLICABLE
ADDITIONAL INSTALLATION INSTRUCTIONS
1. All Class II Pumps located in Zone 1 of swimming pool areas require locating where flooding cannot occur.
2. This pump is intended to be installed as “fixed” as opposed to portable.
3. The Rain Roof must be installed and “vertical orientation” mounting of entire unit observed.
4. After installation, the power supply plug must be accessible during use.
5. This unit must be scrapped if the supply cord is damaged.
6. Observe and comply with all National Wiring Standards.
ZUSTAZLICHE INSTALLIERUNGSANWEISUNGUN
1. Pumpen die sich in Zone 1 vom Schwimmbecken befinden sollen sind so einzurichten daß
Ueberschwemmungen nicht vorkommen werden.
2. Diese Pumpe ist als fest montierte Ausrustung bedacht und soll nicht umstellbar gebraucht werden.
3. Der Regendach muss installiert werden. Eine vertikale Asrichtung der Montage muß erzielt werden.
4. Die Stromversorgung muss nach der Installierung noch zuganglich sein.
5. Bei beschadigter Verkabelung ist dieses Gerat nicht mehr zu gebrauchen.
6. Staatliche Vernetzungsvorchriften mussen eingehalten werden.
INSTRUCTIONS SUPPLÉMENTAIRES D’INSTALLTION
1. Toutes les pompes installées dans la Zone 1 du périmètre de la piscine doivent être situées de manière à
ne pas pouvoir être inondées.
2. Cette pompe est prévue pour installation fixe et non pas portative.
3. L’abri anti-pluie doit être installé et l’orientation verticale doit toujours être observée.
4. Après l’installation, la prise électrique doit rester accessible pendant l’utilisation.
5. Cette unité doit être mise au rebut si le cordon électrique est endommagé.
6. Observez et adhérez à toutes les Normes Nationales pour Installations Electriques.
INSTRUCCIONES ADICIONALES PARA INSTALACION
1. Todas las bombas Clase II situadas en la Zona 1 de las áreas de la piscina requieren colocarse donde no
puedan ser inundadas.
2. Esta bomba es para ser instalada “fija” en vez de portátil.
3. Es necesario instalar el techo de lluvia, y montar la unidad entera siguiendo una orientación vertical.
4. Depués de la instalación el enchufe suministrador de energía debe estar accesible durante el uso.
5. Se deberá deshechar la unidad si el cordón de abastecimiento se deteriora.
6. Observe y cumpla con todas las Reglas Nacionales para Instalaciones Eléctricas.
ISTRUZIONI SUPPLEMENTARI PER L’ INSTALLAZIONE
1. Tutte le pompe Classe II localizzate nella Zona 1 della superficie circostante la piscina devono essere
collocate dove gli allagamenti no possono accadere.
2. Questa pompa, é inteso, deve essere installata come ‘fissa’ e non come portatile.
3. La tettoia deve essere installata e il montaggio ‘orientazione verticale’ dell’intera unitá deve essere osservato.
4. Dopo l’installazione, la spina deve essere accessibile durante l’uso.
5. Questa unitá deve essere gettata via se il filo elettrico é danneggiato.
6. Osservare e aderire a tutte le Norme Nazionali Sugli Impianti Elettrici.

USA and Canada 800.683.2378, International 904.641.1666 17
INSTALLATION DIAGRAM
Rain Roof slides into
wall mounting bracket
(no tools necessary).
On/Off Switch (under
roof, not visible this view)
Vertical Wall Mounting Bracket
(requires 2 screws)
Discharge Line
Disassembled View
Suction Line
Solution Tank
Shut-Off Valve
Grounded Power Outlet;
protected by Ground-Fault
Circuit-Interrupter (GFCI)
Always use Rain Roof
for outdoor use or if
metering pump is
subject to washdowns.
Injection
Fitting
25 psi max.
Injection
Check Valve
100 psi max.
Flow direction
of solution
Disassembled View
Duckbill
Injection Check Valve
or Injection Fitting

18
INSTALLATION continued
SPILL RECOVERY
Mount the pump vertically and use the spill recovery to drain chemical back to the tank in
the event of tube failure. This will help prevent chemical from collecting in the tube housing
and reduces spillage on the floor.
The pump motor is ventilated and water intrusion can cause motor damage. A rain roof is
recommended for outdoor and wet environments.
Strainer with Weight
Spill Recovery
3"
www.stenner.com
Tube drains solution
back to tank.
Punch out one of two hole plugs
using a 7/32" punch or drill.
Use section of 1/4"
suction/discharge tubing
and insert in hole.

USA and Canada 800.683.2378, International 904.641.1666 19
INSTALLATION continued
*For 3/8" connections only. While stabilizing the tube fitting, attach female end of adapter to the tube fitting(s)
(ferrule inside). Slide line through 3/8" connecting nut and finger tighten to male end of adapter. If leak
occurs, gradually tighten the 3/8" connecting nut as required.
Finger
tighten
1/4" nut Ferrules
DO NOT use thread
seal tape on pump
tube threads.
DO NOT use pliers.
Connecting Nut
NOTE: Beveled ends of
ferrules face pump.
Tubing should bottom
into all fittings.
INSTALL SUCTION LINE TO PUMP HEAD
1. Uncoil the suction/discharge tubing. Use outside of solution tank as a guide to cut
proper length of suction line ensuring it will be 2-3" above the bottom of solution tank.
Allow sufficient slack to avoid kinks and stress cracks. Always make a clean
square cut to assure that the suction line is burr free. Normal maintenance
requires trimming.
Suction lines that extend to the bottom of the tank can result in debris pickup
leading to clogged injectors and possible tube failure.
2. Make connections by sliding the line(s) through connecting nut*and ferrule and
finger tighten to the corresponding tube fittings.
3. Finger tighten nut to the threaded tube fitting while holding the tube fitting.
Over tightening the ferrule and nut with a wrench may result in damaged fittings,
crushed ferrules, and air pick up.
DO NOT use thread seal tape on pump tube connections or tools to
tighten connections.
More on next page

www.stenner.com
20
INSTALLATION continued
3"
Suction Line
3.5"
(9 cm)
Weighted
Suction Line
Strainer
INSTALL SUCTION WEIGHT TO SUCTION LINE
1. Drill a hole into the bung cap or solution tank lid. Slide the tubing through and secure
the weighted strainer to the line.
2. To attach the strainer, push approximately 3.5" of suction line through the cap on the
strainer body. Pull tubing to make sure it is secure.
3. Suspend slightly above tank bottom to reduce the chance of sediment pickup.
DO NOT mix chemicals in the solution container. Follow recommended mixing
procedures according to the manufacturer.
DO NOT operate pump unless chemical is completely in solution. Turn pump off
when replenishing solution.