Stevens ToT mate TML403R User manual

1
#0964-3144
3594.TML403.10/26/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TML403R
IMPORTANT!
Assembly must be securely attached to
building structure with anchoring devices
of appropriate type, size and quantity in
accordance with applicable codes and
accepted installation practices.
TML403R
5-Section Wall Locker
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;
;;
;;
;;




'(6&5,37,21
(QG5
(QG/
6KHOI0LG
7RS%RW
'LYLGHU6KRUW
'LYLGHU/RQJ
%DFN
%DFN6KRUW
6WULQJHU
+RRN$GYWJ&RDW'EO+RU]1L
6FUHZ7DSS3K2Y1,[
6FUHZ&RQQ+[)O=1PP[PP
6FUHZ&RQQ+['F1LPP[PP

TML403R
STEP-BY-STEP ASSEMBLY
2#0964-3144
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TML403.10/26/18
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported during assembly to avoid damage.
Do not over-tighten screws or it will damage the pre-drilled holes;
snug fit is adequate.
channel
channel
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;
;;
;;
;;




'(6&5,37,21
(QG5
(QG/
6KHOI0LG
7RS%RW
'LYLGHU6KRUW
'LYLGHU/RQJ
%DFN
%DFN6KRUW
6WULQJHU
+RRN$GYWJ&RDW'EO+RU]1L
6FUHZ7DSS3K2Y1,[
6FUHZ&RQQ+[)O=1PP[PP
6FUHZ&RQQ+['F1LPP[PP
HARDWARE / TOOLS INCLUDED
Confirmat Bolt (13)
(Screw Conn HxDc Ni 7mmx50mm)
Hex Wrench
Flat Head Confirmat Bolt (12)
(Screw Conn HxFl ZN 7mmx50mm)
Coat Hook Screw (11)
(Screw Tapp PhOv NI #10x.75)
Coat Hook (10)
(Hook Advtg Coat Dbl Horz Ni)
(Phillips screwdriver required but not included.)

TML403R
STEP-BY-STEP ASSEMBLY
3
#0964-3144
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TML403.10/26/18
Lay Shelf (3) flat on floor, with side having the
most holes facing down.
STEP
1
Insert dowels on Short Dividers (5) into holes on
Shelf (3), making sure all raw edges are facing the
same direction (will be toward back of unit). Press
firmly into place.
STEP
2
Align holes on one Top-Bottom (4) with dowels
on Short Dividers (5). Make sure raw edges on
Short Dividers (5) and Shelf (3) are facing toward
routed channel on Top-Bottom (4). Press Top-
Bottom (4) firmly into place.
STEP
3
Secure Top-Bottom (4) to two center Short
Dividers (5) with two Confirmat Bolts (13), using
the included Hex Wrench.
STEP
4
Carefully turn assembly over, so Shelf (3) is facing
up. Secure Shelf (3) to two center Short Dividers
(5) with two Flat Head Confirmat Bolts (12). This
will be referred to as the Divider Assembly in
Step 7.
STEP
5
Lay Left End (2) flat on floor, with side having the
most holes facing up.
STEP
6
raw edge
raw edges
raw edges
channel

TML403R
STEP-BY-STEP ASSEMBLY
4#0964-3144
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TML403.10/26/18
Beginning with the holes closest to Left End (2),
insert dowels on each Long Divider (6) first into
holes on Top-Bottom (4), then into corresponding
holes on bottom of Shelf (3). To provide enough
room, Top-Bottom (4) can be moved slightly,
but no more than necessary. Make sure all raw
edges are facing same direction (toward back of
unit). Press all parts firmly into place.
STEP
9
Dividers (5 & 6) each have one hole in raw (back)
edge. Backs (7 & 8) each have two holes on back
face. These holes will be used to join Dividers (5
& 6),Backs (7 & 8) and Stringers (9) together in
Step 18. (Holes on back edge of the two center
dividers will not be used.)
STEP
10
Slide Backs (7 & 8) into channels on Top-
Bottoms (4). IMPORTANT: Make sure four holes
on Backs (7 & 8) align with holes on outside
Dividers (5 & 6). Press Backs (7 & 8) together
and seat firmly against Left End (2).
STEP
11
Insert dowels on one end of Divider Assembly
from Step 5 into holes on Left End (2). Make sure
raw edges of Divider Assembly are facing flat
(back) edge of Left End (2), and channel on Top-
Bottom (4) is facing toward bottom of unit. Press
firmly into place.
STEP
7
Divider
Assembly
flat (back) edge
raw edge
bottom edge
channel
Insert dowels on remaining Top-Bottom (4) into
holes on Left End (2). Make sure channel on Top-
Bottom (4) is facing interior of unit and is aligned
with channel on other Top-Bottom (4). Press
firmly into place.
STEP
8
channels
raw (back) edges
channels
holes must
align when
back is seated
holes must
align when
back is seated
NOTE:
Movement of
Top-Bottom (4)
is exaggerated
in illustration,
in order to
better depict
Divider (6)
installation.

TML403R
STEP-BY-STEP ASSEMBLY
5
#0964-3144
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TML403.10/26/18
Insert dowels on Stringers (9) into holes on Left
End (2). Make sure holes on face of Stringers (9)
align with holes on Backs (7 & 8) (reference Step
11). Press firmly into place.
STEP
12
Secure Right End (1) to Top-Bottoms (4), Shelf
(3) and Stringers (9) with eight Confirmat Bolts
(13).
STEP
14
Position Right End (1) on top of assembly, so
dowels on Top-Bottoms (4), Shelf (3) and
Stringers (9) align with holes on Right End (1).
Press firmly into place.
STEP
13
Carefully turn unit over, so Left End (2) is facing
up.
STEP
15

TML403R
STEP-BY-STEP ASSEMBLY
6#0964-3144
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TML403.10/26/18
Repeat Step 14 to secure Left End (2) to Top-
Bottoms (4), Shelf (3) and Stringers (9).
STEP
16
Carefully position assembly with back facing up.
STEP
17
Secure Stringers (9), Backs (7 & 8) and outside
Dividers (5 & 6) together with four Flat Head
Confirmat Bolts (12).
STEP
18
Secure lower Top-Bottom (4) to two center Long
Dividers (6) with two Confirmat Bolts (13).
STEP
19
Carefully position unit with back flat on floor.
STEP
20
Attach each Coat Hook (10) to underside of Shelf
(3) using two Coat Hook Screws (11) and pre-
drilled holes. (Phillips screwdriver not included.)
STEP
21

TML403R
STEP-BY-STEP ASSEMBLY
7
#0964-3144
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TML403.10/26/18
Carefully stand unit upright.
STEP
22
Ensure that all joints, bolts and screws are tight.
STEP
23
This completes the assembly.