Stevens 84152 User manual

1
3249.IDS-84152/84158.7/26/12 ©2012 Stevens Industries, Inc. Due to continuing product development, Stevens reserves the right to change specifications without notice.
Stevens I.D.SYSTEMS™
800.350.3270
www.IDSystemsStorage.com
I.D.SYSTEMS
TM
STEP-BY-STEP INSTALLATION
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing or
damaged, please call Stevens for immediate parts replacement (1-800-350-3270). When
ordering parts, give the Model Number and Color of the unit.
NOTE:
Pulls are preinstalled on the inside of fronts and must be reinstalled on the outside.
However, they are shown in their final mounting position on installation drawings.
#0964-2938
84152/84158
COMPACT ISLAND DESKS
3
1/4" Back
Panel
Screws
For the Drawer-over-Door Cabinet, also remove
1/4" Back Panel. To do this, remove two (2)
screws at top of Panel, then slide Panel over to
one side to allow removal from side and bottom
grooves. This Panel will be reinstalled later.
1Note that there are two (2) Mounting Rails on
back side of Base Cabinets.
Mounting
Rails
(back view)
2Remove at least top and bottom drawers from
Base Cabinets, to provide access during later
steps. Be sure to note their location, as they must
go back in same location when installation is
complete.
Illustrations are general in nature and
do not depict components and details
unrelated to the assembly process.

84152/84158 COMPACT ISLAND DESKS
STEP-BY-STEP INSTALLATION
23249.IDS-84152/84158.7/26/12©2012 Stevens Industries, Inc. Due to continuing product development, Stevens reserves the right to change specifications without notice.
I.D.SYSTEMS
TM
#0964-2938
Back Panel
Clamp Location
Base
Cabinet
Base
Cabinet
Clamp
Location
Apron
Assembly
Back Panel
Outside Edges
Aligned
Base
Cabinet
Toe Kick
Clamp Location
4
9
5
6
7
8
With Back Panel flat on floor and holes facing
up: Attach Toe Kick to Back Panel, by aligning
predrilled holes and using four (4) 1 1/4" Screws.
Open Base Cabinet door. Note that there are
two (2) predrilled holes in each Base Cabinet
Mounting Rail. Use four (4) 1 1/4" Screws through
these holes to attach Base Cabinet to Back
Panel. Remove Clamp.
Position 4-Drawer Base Cabinet against Toe
Kick. Align top and outside edges of Back Panel
and Base Cabinet. Clamp Back Panel to Base
Cabinet Upper Mounting Rail to hold securely in
place for next step.
Position pre-assembled Apron Assembly between
Base Cabinets, with top edges aligned and Apron
Assembly snug against Back Panel. Clamp Apron
Assembly to Base Cabinets to hold securely in
place for next step.
Attach Apron Assembly to Base Cabinets, using
six (6) 1 1/4" Screws through predrilled holes in
Apron Assembly.
Stand assembly upright. Position Drawer-over-
Door Base Cabinet against Toe Kick. Align top
and outside edges of Back Panel and Base
Cabinet. Clamp Back Panel to Base Cabinet
Upper Mounting Rail to hold securely in place for
next step.
(top view)
Back Panel
1 1/4"Screws (typ.)
Toe Kick
Back Panel
Outside
Edges
Aligned
Base
Cabinet
Toe Kick
Clamp Location
Back Panel
Base Cabinet
Mounting Rails
1 1/4"
Screws
(typ.)
Apron Assembly
1 1/4"Screws
(typ.)
Base Cabinet Base Cabinet

84152/84158 COMPACT ISLAND DESKS
STEP-BY-STEP INSTALLATION
3
3249.IDS-84152/84158.7/26/12 ©2012 Stevens Industries, Inc. Due to continuing product development, Stevens reserves the right to change specifications without notice.
I.D.SYSTEMS
TM
#0964-2938
Silicone Sealant
(typ.)
Molded Corner
Brackets (typ.)
Front Rails
(typ.)
Drilled
Access
Holes
Levelers
14 Note that there are two (2) front corner Levelers
located behind each Base Cabinet toe kick and
accessible through drilled access holes in cabinet
floor. Remove plastic plugs from access holes in
order to perform leveling adjustments in next step.
10 Attach 4-Drawer Base Cabinet to Back Panel,
using four (4) 1 1/4" Screws through predrilled
holes in Mounting Rails. Remove Clamps.
11 Apply silicone sealant to Base Cabinet and
Apron Assembly Front Rails and Molded Corner
Brackets, as illustrated below.
12 Place Countertop on top of Desk Assembly,
centering it side-to-side and overhanging
the Back Panel by 1/2". There should be
approximately 3/4" overhang on sides and 2"
overhang at the front. Clamp Countertop down to
Base Cabinet Front Rails, if required, until sealant
is set.
(top view)
CAUTION!
Countertops are quite heavy.
Please use caution when handling.
Do not attempt to handle without additional assistance.
13 Position Desk Assembly in desired location.
Approx.2"
Front Overhang (end view) Approx.1/2" Back Overhang
Back Panel Base Cabinet
Mounting Rails
1 1/4"
Screws
(typ.)

84152/84158 COMPACT ISLAND DESKS
STEP-BY-STEP INSTALLATION
43249.IDS-84152/84158.7/26/12©2012 Stevens Industries, Inc. Due to continuing product development, Stevens reserves the right to change specifications without notice.
I.D.SYSTEMS
TM
#0964-2938
15 Using a level, adjust Levelers until sidewall, front
edge and cabinet floor are plumb. Insert a 4mm
hex wrench through access holes in cabinet floor
to make adjustments. Shim as necessary. Once
adjustments are complete, reinstall plastic plugs
into access holes.
Drilled holes in
cabinet floor
allow access to
levelers
NOTE:
Turn clockwise to lift,
counterclockwise to lower.
17 Finish each Base Cabinet Toe Kick fascia and
Toe Kick on back side of Desk Assembly using 4"
vinyl base molding application. I.D.SYSTEMS™
base molding (provided) has a self-adhesive
backing. After removing protective cover strip,
take care to properly position vinyl base before
applying pressure for permanent adhesion.
This completes the installation.
16 Replace drawers in Base Cabinets, making sure
to return them to their original locations. Reinstall
1/4" Back Panel in Drawer-over-Door Base
Cabinet by reversing procedure in Step #3.