Stevens Tot mate TMS501R User manual

1
#0964-3152
3594.TMS501.9/26/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TMS501R
TMS501R
Book / Toy Storage
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;
;;


'(6&5,37,21
6KHOI8SSHU
(QG8
)U%D
%RWWRP
%DFN
'LYLGHU8SSHU
'LYLGHU/RZHU
6FUHZ&RQQ+['F1LPP[PP
6FUHZ7D
SS
3K:K=LQF;
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported
during assembly to avoid damage.
Do not over-tighten screws or it will
damage the pre-drilled holes;
snug fit is adequate.
HARDWARE / TOOLS INCLUDED
Hex Wrench
Confirmat Bolt (8)
(Screw Conn HxDc Ni 7mmx50mm)
Back Screw (9)
(Screw Tapp PhWh Zinc #8x1.25)
(Phillips screwdriver required but not included.)

TMS501R
STEP-BY-STEP ASSEMBLY
2#0964-3152
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TMS501.9/26/18
Lay one Front-Back (3) flat on floor, with side
having the most holes facing up.
STEP
1
Insert dowels on Upper Dividers (6) into holes on
Front-Back (3). Press firmly into place.
STEP
2
Position other Front-Back (3) on top of assembly,
so dowels on Upper Dividers (6) align with holes
on Front-Back (3). Press firmly into place.
STEP
3
Secure Front-Back (3) to Upper Dividers (6) with
four Confirmat Bolts (8), using the included Hex
Wrench.
STEP
4
Carefully turn assembly over, so other Front-Back
(3) is facing up.
STEP
5
Repeat Step 4 to secure Front-Back (3) to Upper
Dividers (6). This will be referred to as the Front/
Back Assembly in Step 8.
STEP
6

TMS501R
STEP-BY-STEP ASSEMBLY
3
#0964-3152
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TMS501.9/26/18
Lay one End (2) flat on floor, with side having the
most holes facing up.
STEP
7
Insert dowels on one end of Front/Back
Assembly into holes on End (2). Make sure holes
on Front/Back Assembly align with thru-holes on
End (2). Press firmly into place.
STEP
8
Insert dowels on Upper Shelf (1) into holes on
End (2), making sure side of Upper Shelf (1) with
the most holes is facing toward bottom of unit.
Press firmly into place.
STEP
9
Insert dowels on Bottom (4) into remaining holes
on End (2), making sure side with the most holes
is facing toward Upper Shelf (1). Press firmly into
place.
STEP
10
Front/Back
Assembly
thru-holes
Front/Back
Assembly
bottom edge

TMS501R
STEP-BY-STEP ASSEMBLY
4#0964-3152
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TMS501.9/26/18
Insert dowels on Lower Divider (7) first into holes
on Bottom (4), then into corresponding holes on
bottom of Upper Shelf (1). To provide enough
room, Bottom (4) can be moved slightly, but no
more than necessary. Make sure raw edges are
facing same direction. Press all parts firmly into
place.
STEP
11
Position other End (2) on top of assembly, so
dowels on Front/Back Assembly, Upper Shelf
(1) and Bottom (4) align with holes on End (2).
Press firmly into place.
STEP
12
Secure End (2) to Front/Back Assembly, Upper
Shelf (1) and Bottom (4) with eight Confirmat
Bolts (8).
STEP
13
Carefully turn assembly over, so other End (2) is
facing up.
STEP
14
raw edge
raw edge
Front/Back
Assembly
Front/Back
Assembly
NOTE:
Movement of
Bottom (4) is
exaggerated
in illustration,
in order
to better
depict Lower
Divider (7)
installation.

TMS501R
STEP-BY-STEP ASSEMBLY
5
#0964-3152
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TMS501.9/26/18
Repeat Step 13 to secure End (2) to Front/Back
Assembly, Upper Shelf (1) and Bottom (4).
STEP
15
Position Back (5), so two pre-drilled holes align
with edge of Bottom (4), and one pre-drilled hole
aligns with edge of Lower Divider (7).
STEP
17
Front/Back
Assembly
Carefully position assembly so raw edges of
Bottom (4) and Lower Divider (7) are facing up.
STEP
16
raw edges
Secure Back (5) to Bottom (4) and Lower
Divider (7) with three Back Screws (9). (Phillips
screwdriver not included.) IMPORTANT! Make
sure Back Screws are centered on raw edge
of Bottom and Lower Divider and inserted
straight into both panels. This is necessary to
prevent Back Screws from protruding through
and damaging panel surfaces.
STEP
18

TMS501R
STEP-BY-STEP ASSEMBLY
6#0964-3152
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TMS501.9/26/18
Secure Upper Shelf (1) and Bottom (4) to Lower
Divider (7) with one Confirmat Bolt (8) each
STEP
19
Carefully stand unit upright.
STEP
20
Ensure that all joints, bolts and screws are tight.
STEP
21
This completes the assembly.