Stevens Tot mate TM2182R User manual

1
#0964-3128
3594.TM2182.9/25/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TM2182R
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported
during assembly to avoid damage.
Do not over-tighten screws or it will
damage the pre-drilled holes;
snug fit is adequate.
HARDWARE / TOOLS INCLUDED
Confirmat Bolt (5)
(Screw Conn HxDc Ni 7mmx50mm)
Hex Wrench
TM2182R
Toddler Play Center
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;

'(6&5,37,21
(QG8
)[G6KHOI
7RS
5DLO)U%D
6FUHZ&RQQ+['F1LPP[PP

TM2182R
STEP-BY-STEP ASSEMBLY
2#0964-3128
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2182.9/25/18
Lay one End (1) flat on floor, with side having the
most holes facing up.
STEP
1
Insert dowels on one Fixed Shelf (2) into holes at
bottom of End (1). Press firmly into place. Repeat
with other Fixed Shelf (2), using holes in middle of
End (1).
STEP
2
Insert dowel on one Rail (4) into lower hole at top
of End (1). Ensure hole on bottom edge of Rail (4)
aligns with thru-hole in Top (3) (reference STEP
3 illustration). Press firmly into place. Repeat for
other Rail (4).
STEP
4
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported during assembly to avoid damage.
Do not over-tighten screws or it will damage the pre-drilled holes;
snug fit is adequate.
bottom edge
Insert dowels on Top (3) into remaining holes on
End (1). Make sure side of Top (3) with holes is
facing toward top edge of unit. Press firmly into
place.
STEP
3
holes for attachment
of Rail (4) referenced
in STEPS 4 & 9
top edge
hole on bottom edge of
Rail (4) must align with
thru-hole in Top (3)
top edge
Position other End (1) on top of assembly, so
dowels on Rails (4), Top (3) and Fixed Shelves
(2) align with holes on End (1). Press firmly into
place.
STEP
5

TM2182R
STEP-BY-STEP ASSEMBLY
3
#0964-3128
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2182.9/25/18
Secure End (1) to Rails (4), Top (3) and Fixed
Shelves (2) with seven Confirmat Bolts (5), using
the included Hex Wrench.
STEP
6
Carefully turn unit over, so other End (1) is facing
up.
STEP
7
Ensure that all joints and bolts are tight.
STEP
11
This completes the assembly.
Repeat Step 6 to secure End (1) to Rails (4), Top
(3) and Fixed Shelves (2).
STEP
8
STEP
10
Carefully stand unit upright.
Secure Top (3) to Rails (4) with two Confirmat
Bolts (5).
STEP
9
(one side shown)