STI Stopper SS2 8 Series Quick guide

Stopper®Station Series SS2xx8
Push Button Pneumatic Timer Button
neumatic Timer Models
SS20x8 Red
SS21x8 Green
SS22x8 Yellow
SS23x8 White
SS24x8 Blue
A MODE S COME WITH A
CO OR MATCHED SURFACE
MOUNT BACKBOX
ADA
for operation
We protect the things that protect you.®

- 2 -
Installation and Service Instructions
STOPPER®STATION SERIES SS2xx8
PUSH BUTTON PNEUMATIC TIMER
SAFETY NOTICE TO INSTALLERS AND USERS
I. GENERAL
roduct Dimensions See page 3
Contact Rating One set NO and one set NC
Rated at 10 AMP @ 240 VAC
Recognized component listing is
1,000,000 cycles
U File #U 57255 Operating Temperature of button 15°-120°F (-9°to +49°C
II. CONTENTS LIST
QTY. DESCRI TION
1Push Button Housing Assembly
1 Allen Head Screw #8-32 x 3/8 in.
1Allen Wrench 3/32 in.
4#6 x 5/8 in. hi-low screw
2 Screw #6-32 x 1 in.
1 Ground Screw
4#6 x 1 1/4 in. SS SMS
4 Plastic Screw Anchor
1 71100A Surface Backbox
III. INSTRUCTIONS
Product Dimensions .......................................................................... Page 3
Front Housing Removal .................................................................... Page 3
Backbox Preparation ........................................................................ Page 4
Switch Contact Diagram.................................................................... Page 5
Switch Data........................................................................................ Page 5
Installation ........................................................................................ Page 6
Warranty .......................................................................................... Page 7

- 3 -
Safety Notice to Installers and Users
This push button has been tested according to U2017. It is important to read, understand
and follow all instructions provided with this product. Non-fire alarm initiating devices are
listed in U category UEHX. It is the installer’s responsibility to comply with NEC and Canadian
electrical code, mounting specifications according to ADA and other applicable fire and
electrical codes. To avoid electrical shock , DO NOT attempt to install this product when
power is on. To avoid possible confusion with fire alarm initiating devices, do not mount a
red stopper station near a manual fire alarm initiating device. ADA mounting compliance
requires the operable part of the initiating device shall not be less than 1.1m (3 1/2 ft.) or
greater than 1.37m (4 1/2 ft.) above finished floor service. After installation and testing are
complete, provide a copy of this manual to all personnel responsible for testing and
maintenance of this product. Push buttons for outdoor use must be mounted with STI
outdoor rated covers.
* For access control installations, power for the SS2xx8 must be supplied by a power source
isted to U294. When used for access control, this device shall be used as a part of an access
controlled egress door system. It is up to the local AHJ to allow use of this device in place of
an automatic sensor. For higher security installations, lower time limits should be used.
Remarques sur l’installation:Ce bouton-poussoir a été testé selon U 2017. Il est important de
lire, de comprendre et de suivre toutes les instructions fournies avec ce produit. es dispositifs
de déclenchement d’alertes non incendie sont répertoriés sous la catégorie U UEHX. Il incombe
à l’installateur de se conformer aux normes NEC et Code canadien de l’électricité, aux
spécifications de montage selon l’ADA et aux autres codes de prévention des incendies et de
l’électricité en vigueur. Pour éviter un choc électrique, NE tentez PAS d’installer ce produit
lorsqu’il est sous tension. Pour éviter toute confusion possible avec les dispositifs de
déclenchement d’alertes d’incendie, n’installez pas un avertisseur Stopper rouge à proximité
d’un dispositif de déclenchement d’alarme d’in cendie manuel. a conformité aux règles
d’installation de l’ADA exige que la partie utilisable du dispositif de déclenchement soit installée
à une hauteur située entre 1,1 m (3 1/2 pi) et 1,37 m (4 1/2 pi) au-dessus du plancher fini.
Une fois l’installation et les essais terminés, vous devez fournir une copie de ce manuel à
l’ensemble du personnel chargé de l’essai et de l’entretien de ce produit. es boutons poussoirs
pour utilisation à l’extérieur doivent être installés avec couvercles pour l’extérieur de STI.
* Pour les installations de contrôle d’accès, l’alimentation SS2xx8 doit être fournie par une
source homologuée U 294. orsque cet appareil est utilisé aux fins de contrôle d’accès, il doit
faire partie d’un système de porte de sortie à accès contrôlé. Il incombe donc à l’AHJ local
d’autoriser l’utilisation de cet appareil au lieu d’un capteur automatique. Pour les installations
de sécurité plus renforcée, des délais inférieurs doivent être utilisés.

VIE SHO ING FRONT HOUSING REMOVAL
- 4 -
PRODUCT DIMENSIONS
SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3
BUTTON AND SWITCH ASSEMBLY
WRENCH
(1) PROVIDED
SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
QTY. PART No. NAME
P
4
1 1
1 2
1
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
12
9
IS NOT USED
1
1.62 in.
(41mm)
3.25 in. (82mm)
1.58 in.
(40mm)
1.375 in.
(35mm)
PUSH
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
12
9
8 x 1
A
IS NOT USED
1
6-32 x 1. 00
1
4.87 in.
(124mm)

J
J
J
J
HSWITCH BACKPLATE
MOUNTING HOLES
BOX MUST BE INSTALLED WITH
ARROWS POINTING UPWARD
THESE HOLES MUST BE
DRILLED OUT USING A
5/32 in. DRILL BIT
H
J
OUNTING HOLESM
T
CKPLA
ATE
ACH BWITS
H
J
ALLED WITHTT BE INSUSX MOB
TE
ALLED WITH
J
J
WS POINTING UPWOARR
ALLED WITHTT BE INSUSX MOB
5/32 in. DRILL BIT
DRILLED OUT USING A
T BEUSTHESE HOLES M
H
ARDWS POINTING UPW
ALLED WITH
5/32 in. DRILL BIT
DRILLED OUT USING A
T BE
BACKBOX PREPARATION
(NOT INCLUDED WITH FLUSH MOUNT COVERS)
FIELD DRILLING FOR CONDUIT ENTRY IS
REQUIRED. LOCATIONS SHOWN ALSO
A LY TO O OSITE, ARALLEL SIDES.
- 5 -
J
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
D
S NEEDEDDRILL A
ONDUIT FITC
OP AND BT
DRILL POINT L
S NEEDED
.TINGSONDUIT FIT
OR 1/2 in.M FOTTOOP AND B
VIDEDOTIONS PROCADRILL POINT L

CONTACT DIAGRAM
S ITCH INFORMATION
- 6 -
CONTACTS
One set NO and one set NC
LEAD WIRE COLORS
IN ARENTHESIS.
QTY. PART No. NAME
P
4
1 1
1 2
1
12
1
SETTING – 25 TO 45 SECONDS
F
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
8 x 1
A
IS NOT USED
1
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
QTY. PART No. NAME
P
3
4
1 1
1 2
1
QTY. PART No. NAME
P
3
3
4
1 1
1 2
1
IS NOT USED
1
NC
NO
NC
NO
BUTTON ACTIVATED
M
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.

ITHOUT PROVIDED
SURFACE BACK BOX
- 7 -
ITH PROVIDED
SURFACE BACK BOX
INSTALLATION
QTY. PART No. NAME
P
4
1 1
1 2
1
8 x 1
A
3.5mm x 13mm
T
QTY. PART No. NAME
P
3
4
1 1
1 2
1
12
9
IS NOT USED
1
TYPICAL FLUSH MOUNT
GANG BOX
GROUND LUG
(2) PROVIDED
SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
GROUND SCREW
BUTTON AND SWITCH ASSEMBLY
SCREW #6-32 x 1 in.
(2) PROVIDED
SCREW #6 x 1-1/4 in.
(4) PROVIDED
71100A-COLOR SURFACE BOX
ANCHOR
(4) PROVIDED
DRILL (4) 3/16 in.
DIA HOLES
J
(4) PR
ANCHOR
DIA HOLES
DRILL (4) 3/16 in.
VIDEDO(4) PR
ANCHOR
XOCE BAOR SURFOLC-71100A
VIDEDO(4) PR
1/4 in.-SCREW #6 x 1
SEMBLSCH AWITON AND STBUT
OUND SCREW GR
Y
MBL
LY
VIDEDO(2) PR
32 x 1 in.-SCREW #6
VIDED
32 x 1 in.
INSTALLATION NOTE
ADA mounting compliance
requires the operable part of
the initiating device shall not
be less than 1.1m (3 1/2 ft.) or
greater than 1.37m (4 1/2 ft.)
above finished floor service.

2306 Airport Rd • Waterford, MI 48327
hone: 248-673-9898 • Fax: [phone]
800-888-4STI (4784) • www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G ipers Road • ark Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England
Tel: [phone] • Fax: [phone]
E-mail: [email protected] • Web: www.sti-europe.com
Warranty
Three year guarantee against breakage of polycarbonate in normal use (one
year on electro mechanical and electronic components).
Electronic warranty form at www.sti-usa.com/wc14.
2008 A-IS
June2015