STI Stopper Station Series User manual

Stopper®Station Series SS2xx8
Push Button Pneumatic Timer Button
We protect the things that protect you.®
ADA
for operation
Pneumatic Timer Models
SS20x8 Red
SS21x8 Green
SS22x8 Yellow
SS23x8 White
SS24x8 Blue
ALL MODELS COME
WITH A COLOR
MATCHED SURFACE
MOUNT BACKBOX

Installation and Service Instructions
STOPPER®STATION SERIES SS2xx8
PUSH BUTTON PNEUMATIC TIMER
SAFETY NOTICE TO INSTALLERS AND USERS
III. INSTRUCTIONS
Product Dimensions ...................................................................................................... Page 4
Front Housing Removal................................................................................................. Page 4
Backbox Preparation ..................................................................................................... Page 5
Switch Contact Diagram................................................................................................ Page 6
Switch Data ................................................................................................................... Page 6
Installation ..................................................................................................................... Page 7
Warranty ........................................................................................................................ Page 8
I. GENERAL
Product Dimensions See page 3
Contact Rating One set NO and one set NC
Rated at 10 AMP @ 240 VAC
Recognized component listing is
1,000,000 cycles
UL File #UL57255 Operating Temperature of button 15°-120°F (-9°to +49°C)
II. CONTENTS LIST
QTY. DESCRIPTION
1 Push Button Housing Assembly
1 Allen Head Screw #8-32 x 3/8 in.
1 Allen Wrench 3/32 in.
4 #6 x 5/8 in. hi-low screw
2 Screw #6-32 x 1 in.
1 Ground Screw
4 #6 x 1 1/4 in. SS SMS
4 Plastic Screw Anchor
1 71100A Surface Backbox
- 2 -

Safety Notice to Installers and Users
This push button has been tested according to UL2017. It is important to read, understand and
follow all instructions provided with this product. Non-re alarm initiating devices are listed in UL
category UEHX. It is the installer’s responsibility to comply with NEC and Canadian electrical
code, mounting specications according to ADA and other applicable re and electrical codes.
To avoid electrical shock , DO NOT attempt to install this product when power is on. To avoid
possible confusion with re alarm initiating devices, do not mount a red stopper station near
a manual re alarm initiating device. ADA mounting compliance requires the operable part
of the initiating device shall not be less than 1.1m (3 1/2 ft.) or greater than 1.37m (4 1/2 ft.)
above nished oor service. After installation and testing are complete, provide a copy of this
manual to all personnel responsible for testing and maintenance of this product. Push buttons
for outdoor use must be mounted with STI outdoor rated covers.
* For access control installations, power for the SS2xx8 must be supplied by a power source Listed to
UL294. When used for access control, this device shall be used as a part of an access controlled egress
door system. It is up to the local AHJ to allow use of this device in place of an automatic sensor. For higher
security installations, lower time limits should be used.
Remarques sur l’installation: Ce bouton-poussoir a été testé selon UL2017. Il est important
de lire, de comprendre et de suivre toutes les instructions fournies avec ce produit. Les
dispositifs de déclenchement d’alertes non incendie sont répertoriés sous la catégorie UL
UEHX. Il incombe à l’installateur de se conformer aux normes NEC et Code canadien de
l’électricité, aux spécications de montage selon l’ADA et aux autres codes de prévention
des incendies et de l’électricité en vigueur. Pour éviter un choc électrique, NE tentez PAS
d’installer ce produit lorsqu’il est sous tension. Pour éviter toute confusion possible avec les
dispositifs de déclenchement d’alertes d’incendie, n’installez pas un avertisseur Stopper rouge
à proximité d’un dispositif de déclenchement d’alarme d’in cendie manuel. La conformité aux
règles d’installation de l’ADA exige que la partie utilisable du dispositif de déclenchement
soit installée à une hauteur située entre 1,1 m (3 1/2 pi) et 1,37 m (4 1/2 pi) au-dessus du
plancher ni. Une fois l’installation et les essais terminés, vous devez fournir une copie de
ce manuel à l’ensemble du personnel chargé de l’essai et de l’entretien de ce produit. Les
boutons poussoirs pour utilisation à l’extérieur doivent être installés avec couvercles pour
l’extérieur de STI.
* Pour les installations de contrôle d’accès, l’alimentation SS2xx8 doit être fournie par une
source homologuée UL294. Lorsque cet appareil est utilisé aux ns de contrôle d’accès, il doit
faire partie d’un système de porte de sortie à accès contrôlé. Il incombe donc à l’AHJ local
d’autoriser l’utilisation de cet appareil au lieu d’un capteur automatique. Pour les installations
de sécurité plus renforcée, des délais inférieurs doivent être utilisés.
- 3 -

PRODUCT DIMENSIONS
VIEW SHOWING FRONT HOUSING REMOVAL
SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
1.62 in.
(41mm)
3.25 in. (82mm)
PRODUCT DIMENSIONS
DRILL (4)
3/16 DIA.
HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW,
WHITE AND BLUE
SCREW
SELF TAPPING
(4) PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
1.58 in.
(40mm)
1.375 in.
(35mm)
SCREW #8 X 1
(4) PROVIDED
IF WIRE ACCESS OR CONDUIT
ENTRY HOLES ARE NEEDED,
THESE HOLES MUST BE FIELD
DRILLED AS REQUIRED.
ANCHOR
(4) PROVIDED
GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE
NOT PROVIDED
19021 GROUND LUG
(2) PROVIDED
19060 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
TIMER RANGE ADJUSTMENT SCREW
* IF NEEDED, MAKE VERY SMALL
ADJUSTMENTS*
TURN COUNTER CLOCKWISE
TO INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
BUTTON AND SWITCH ASSEMBLY
WRENCH
(1) PROVIDED
SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
PUSH
PUSH
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
13 4
14 1
15 2
19724
PART OF 12
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO INCREASE TIMER SPEED
ADJUSTMENT RANGE – 2 TO 60 SECONDS
FACTORY SETTING – 25 TO 45 SECONDS
FAST
SLOW
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
1
2
3
4
5
6
7
89
10
10
11
12
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
10
PRODUCT DIMENSIONS
3.18 in. (81mm)
4.87 in.
(124mm)
3.25 in.(82mm) 1.62 in.(41mm)
13
13 4
14 1
15 2
15
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE REQUIRED, THESE HOLES
MUST BE FIELD DRILLED AS NEEDED
GREEN
YELLOW
BLUE
WHITE
RED
14
19724
PART OF 12
9
PNEUMATIC TIMER SWITCH ASSEMBLY
TOP
71100A MOUNTING INSTRUCTIONS
BOX MUST BE INSTALLED
WITH "TOP" FACING UPWARD
THESE (4) HOLES MUST
BE DRILLED OUT USING
A 3/16 in. DRILL BIT
16
DRILL (4)
3/16 DIA. HOLES
17
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
VIEW SHOWING
TYPICAL FLUSH MOUNT
TO SINGLE GANG BOX
OPTIONAL IF IS NOT USED
14
SWITCH DATA
RATED VOLTAGE - 240 VAC 10 AMP.
(RESISTIVE LIFE CYCLES 1,000,000)
NC
NO
GREEN
YELLOW
BLUE
WHITE
RED
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
NC
NO
NC
NO
DRILL (4)
3/16 DIA. HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW, WHITE AND BLUE
19068 SCREW
SELF TAPPING (4) PROVIDED
19014 SCREW #8 X 1 (4) PROVIDED
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE NEEDED, THESE HOLES
MUST BE FIELD DRILLED AS REQUIRED.
19018 ANCHOR (4) PROVIDED
19021 GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE NOT PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
GROUND LUG
(2) PROVIDED
SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
4.87 in.
(124mm)
SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
1.62 in.
(41mm)
3.25 in. (82mm)
PRODUCT DIMENSIONS
DRILL (4)
3/16 DIA.
HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW,
WHITE AND BLUE
SCREW
SELF TAPPING
(4) PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
1.58 in.
(40mm)
1.375 in.
(35mm)
SCREW #8 X 1
(4) PROVIDED
IF WIRE ACCESS OR CONDUIT
ENTRY HOLES ARE NEEDED,
THESE HOLES MUST BE FIELD
DRILLED AS REQUIRED.
ANCHOR
(4) PROVIDED
GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE
NOT PROVIDED
19021 GROUND LUG
(2) PROVIDED
19060 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
TIMER RANGE ADJUSTMENT SCREW
* IF NEEDED, MAKE VERY SMALL
ADJUSTMENTS*
TURN COUNTER CLOCKWISE
TO INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
BUTTON AND SWITCH ASSEMBLY
WRENCH
(1) PROVIDED
SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
PUSH
PUSH
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
13 4
14 1
15 2
19724
PART OF 12
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO INCREASE TIMER SPEED
ADJUSTMENT RANGE – 2 TO 60 SECONDS
FACTORY SETTING – 25 TO 45 SECONDS
FAST
SLOW
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
1
2
3
4
5
6
7
89
10
10
11
12
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
10
PRODUCT DIMENSIONS
3.18 in. (81mm)
4.87 in.
(124mm)
3.25 in.(82mm) 1.62 in.(41mm)
13
13 4
14 1
15 2
15
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE REQUIRED, THESE HOLES
MUST BE FIELD DRILLED AS NEEDED
GREEN
YELLOW
BLUE
WHITE
RED
14
19724
PART OF 12
9
PNEUMATIC TIMER SWITCH ASSEMBLY
TOP
71100A MOUNTING INSTRUCTIONS
BOX MUST BE INSTALLED
WITH "TOP" FACING UPWARD
THESE (4) HOLES MUST
BE DRILLED OUT USING
A 3/16 in. DRILL BIT
16
DRILL (4)
3/16 DIA. HOLES
17
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
VIEW SHOWING
TYPICAL FLUSH MOUNT
TO SINGLE GANG BOX
OPTIONAL IF IS NOT USED
14
SWITCH DATA
RATED VOLTAGE - 240 VAC 10 AMP.
(RESISTIVE LIFE CYCLES 1,000,000)
NC
NO
GREEN
YELLOW
BLUE
WHITE
RED
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
NC
NO
NC
NO
DRILL (4)
3/16 DIA. HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW, WHITE AND BLUE
19068 SCREW
SELF TAPPING (4) PROVIDED
19014 SCREW #8 X 1 (4) PROVIDED
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE NEEDED, THESE HOLES
MUST BE FIELD DRILLED AS REQUIRED.
19018 ANCHOR (4) PROVIDED
19021 GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE NOT PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
GROUND LUG
(2) PROVIDED
SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
4.87 in.
(124mm)
- 4 -

- 5 -
BACKBOX PREPARATION
(NOT INCLUDED WITH FLUSH MOUNT COVERS)
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
BACKPLATE WITH MOLDED-IN
STAINLESS STEEL INSERT
SWITCH HOUSING MOLDED OF
POLYCARBONATE. CHOOSE RED,
GREEN, YELLOW, WHITE OR BLUE.
ALLEN HEAD
LOCKING SCREW
AND WRENCH
ALSO CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
BUTTON AND SWITCH ASSEMBLY
19015 WRENCH
(1) PROVIDED
FIGURE C
SURFACE BOX
INSTALLATION
19011 SCREW ALLEN HEAD
#8-32 x 3/8 (1) PROVIDED
10271 SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
1.62 in.
(41mm)
3.25 in. (82mm)
4.87 in.
(124mm)
PRODUCT DIMENSIONS
1.58 in.
(40mm)
1.375 in.
(35mm)
1.62 in.
(41mm)
3.25 in.(82mm)
4.87 in.
(124mm)
PRODUCT DIMENSIONS
1.56 in.
(40mm)
"A"
TO PROVIDE ADEQUATE CLEARANCE FOR CONTACTS,
(#0, #1, #3, #4) INSTALLATION
1.62 in.
(41mm)
3.25 in.(82mm)
4.87 in.
(124mm)
1.58 in.
(40mm)
"A"
GROUND SCREW
BUTTON AND SWITCH ASSEMBLY
SCREW #6-32 x 1 in.
(2) PROVIDED
SCREW #6 x 1-1/4 in.
(4) PROVIDED
KIT-71100A-COLOR SURFACE BOX
ANCHOR
(4) PROVIDED
DRILL (4) 3/16 in.
DIA HOLES
J
J
J
J
HSWITCH BACKPLATE
MOUNTING HOLES
BOX MUST BE INSTALLED WITH
ARROWS POINTING UPWARD
THESE HOLES MUST BE
DRILLED OUT USING A
5/32 in. DRILL BIT
H
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
19039 SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
19060 SCREW #6-32 x 1 in.
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
19021 GROUND SCREW
19018 ANCHOR
(4) PROVIDED
THIS VIEW FOR PAGE 6
DRILL (4)
3/16 DIA. HOLES
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
SCREW #6-32 x 1 in.
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND SCREW
ANCHOR
(4) PROVIDED
THIS VIEW FOR PAGE 6
DRILL (4)
3/16 DIA. HOLES
BACKPLATE WITH MOLDED-IN
STAINLESS STEEL INSERT
SWITCH HOUSING MOLDED
OF POLYCARBONATE. CHOOSE
RED, GREEN, YELLOW,
WHITE OR BLUE.
ALLEN HEAD
LOCKING SCREW
AND WRENCH
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
19039 SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
19060 SCREW #6-32 x 1 in.
(2) PROVIDED
19021
GROUND SCREW
19018 ANCHOR
(4) PROVIDED
DRILL (4)
3/16 DIA. HOLES
.728 in.
(18.49mm)
2.4 in.
(60.96mm)
3.218 in.
(81.74mm)
4.132 in.
(104.95mm)
4.83 in.
(122.68mm)
1.578 in.
(40.08mm)
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
BACKPLATE WITH MOLDED-IN
STAINLESS STEEL INSERT
SWITCH HOUSING MOLDED OF
POLYCARBONATE. CHOOSE RED,
GREEN, YELLOW, WHITE OR BLUE.
ALLEN HEAD
LOCKING SCREW
AND WRENCH
ALSO CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
BUTTON AND SWITCH ASSEMBLY
19015 WRENCH
(1) PROVIDED
FIGURE C
SURFACE BOX
INSTALLATION
19011 SCREW ALLEN HEAD
#8-32 x 3/8 (1) PROVIDED
10271 SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
1.62 in.
(41mm)
3.25 in. (82mm)
4.87 in.
(124mm)
PRODUCT DIMENSIONS
1.58 in.
(40mm)
1.375 in.
(35mm)
1.62 in.
(41mm)
3.25 in.(82mm)
4.87 in.
(124mm)
PRODUCT DIMENSIONS
1.56 in.
(40mm)
"A"
TO PROVIDE ADEQUATE CLEARANCE FOR CONTACTS,
(#0, #1, #3, #4) INSTALLATION
1.62 in.
(41mm)
3.25 in.(82mm)
4.87 in.
(124mm)
1.58 in.
(40mm)
"A"
GROUND SCREW
BUTTON AND SWITCH ASSEMBLY
SCREW #6-32 x 1 in.
(2) PROVIDED
SCREW #6 x 1-1/4 in.
(4) PROVIDED
KIT-71100A-COLOR SURFACE BOX
ANCHOR
(4) PROVIDED
DRILL (4) 3/16 in.
DIA HOLES
J
J
J
J
HSWITCH BACKPLATE
MOUNTING HOLES
BOX MUST BE INSTALLED WITH
ARROWS POINTING UPWARD
THESE HOLES MUST BE
DRILLED OUT USING A
5/32 in. DRILL BIT
H
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
19039 SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
19060 SCREW #6-32 x 1 in.
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
19021 GROUND SCREW
19018 ANCHOR
(4) PROVIDED
THIS VIEW FOR PAGE 6
DRILL (4)
3/16 DIA. HOLES
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
SCREW #6-32 x 1 in.
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND SCREW
ANCHOR
(4) PROVIDED
THIS VIEW FOR PAGE 6
DRILL (4)
3/16 DIA. HOLES
BACKPLATE WITH MOLDED-IN
STAINLESS STEEL INSERT
SWITCH HOUSING MOLDED
OF POLYCARBONATE. CHOOSE
RED, GREEN, YELLOW,
WHITE OR BLUE.
ALLEN HEAD
LOCKING SCREW
AND WRENCH
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
19039 SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
19060 SCREW #6-32 x 1 in.
(2) PROVIDED
19021
GROUND SCREW
19018 ANCHOR
(4) PROVIDED
DRILL (4)
3/16 DIA. HOLES
.728 in.
(18.49mm)
2.4 in.
(60.96mm)
3.218 in.
(81.74mm)
4.132 in.
(104.95mm)
4.83 in.
(122.68mm)
1.578 in.
(40.08mm)
FIELD DRILLING FOR CONDUIT
ENTRY IS REQUIRED.
LOCATIONS SHOWN ALSO APPLY
TO OPPOSITE, PARALLEL SIDES.

- 6 -
CONTACT DIAGRAM
SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
1.62 in.
(41mm)
3.25 in. (82mm)
PRODUCT DIMENSIONS
DRILL (4)
3/16 DIA.
HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW,
WHITE AND BLUE
SCREW
SELF TAPPING
(4) PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
1.58 in.
(40mm)
1.375 in.
(35mm)
SCREW #8 X 1
(4) PROVIDED
IF WIRE ACCESS OR CONDUIT
ENTRY HOLES ARE NEEDED,
THESE HOLES MUST BE FIELD
DRILLED AS REQUIRED.
ANCHOR
(4) PROVIDED
GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE
NOT PROVIDED
19021 GROUND LUG
(2) PROVIDED
19060 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
TIMER RANGE ADJUSTMENT SCREW
* IF NEEDED, MAKE VERY SMALL
ADJUSTMENTS*
TURN COUNTER CLOCKWISE
TO INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
BUTTON AND SWITCH ASSEMBLY
WRENCH
(1) PROVIDED
SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
PUSH
PUSH
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
13 4
14 1
15 2
19724
PART OF 12
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO INCREASE TIMER SPEED
ADJUSTMENT RANGE – 2 TO 60 SECONDS
FACTORY SETTING – 25 TO 45 SECONDS
FAST
SLOW
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
1
2
3
4
5
6
7
89
10
10
11
12
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
10
PRODUCT DIMENSIONS
3.18 in. (81mm)
4.87 in.
(124mm)
3.25 in.(82mm) 1.62 in.(41mm)
13
13 4
14 1
15 2
15
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE REQUIRED, THESE HOLES
MUST BE FIELD DRILLED AS NEEDED
GREEN
YELLOW
BLUE
WHITE
RED
14
19724
PART OF 12
9
PNEUMATIC TIMER SWITCH ASSEMBLY
TOP
71100A MOUNTING INSTRUCTIONS
BOX MUST BE INSTALLED
WITH "TOP" FACING UPWARD
THESE (4) HOLES MUST
BE DRILLED OUT USING
A 3/16 in. DRILL BIT
16
DRILL (4)
3/16 DIA. HOLES
17
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
VIEW SHOWING
TYPICAL FLUSH MOUNT
TO SINGLE GANG BOX
OPTIONAL IF IS NOT USED
14
SWITCH DATA
RATED VOLTAGE - 240 VAC 10 AMP.
(RESISTIVE LIFE CYCLES 1,000,000)
NC
NO
GREEN
YELLOW
BLUE
WHITE
RED
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
NC
NO
NC
NO
DRILL (4)
3/16 DIA. HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW, WHITE AND BLUE
19068 SCREW
SELF TAPPING (4) PROVIDED
19014 SCREW #8 X 1 (4) PROVIDED
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE NEEDED, THESE HOLES
MUST BE FIELD DRILLED AS REQUIRED.
19018 ANCHOR (4) PROVIDED
19021 GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE NOT PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
GROUND LUG
(2) PROVIDED
SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
4.87 in.
(124mm)
CONTACTS
One set NO and one set NC
SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
1.62 in.
(41mm)
3.25 in. (82mm)
PRODUCT DIMENSIONS
DRILL (4)
3/16 DIA.
HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW,
WHITE AND BLUE
SCREW
SELF TAPPING
(4) PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
1.58 in.
(40mm)
1.375 in.
(35mm)
SCREW #8 X 1
(4) PROVIDED
IF WIRE ACCESS OR CONDUIT
ENTRY HOLES ARE NEEDED,
THESE HOLES MUST BE FIELD
DRILLED AS REQUIRED.
ANCHOR
(4) PROVIDED
GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE
NOT PROVIDED
19021 GROUND LUG
(2) PROVIDED
19060 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
TIMER RANGE ADJUSTMENT SCREW
* IF NEEDED, MAKE VERY SMALL
ADJUSTMENTS*
TURN COUNTER CLOCKWISE
TO INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
BUTTON AND SWITCH ASSEMBLY
WRENCH
(1) PROVIDED
SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
PUSH
PUSH
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
13 4
14 1
15 2
19724
PART OF 12
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO INCREASE TIMER SPEED
ADJUSTMENT RANGE – 2 TO 60 SECONDS
FACTORY SETTING – 25 TO 45 SECONDS
FAST
SLOW
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
1
2
3
4
5
6
7
89
10
10
11
12
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
10
PRODUCT DIMENSIONS
3.18 in. (81mm)
4.87 in.
(124mm)
3.25 in.(82mm) 1.62 in.(41mm)
13
13 4
14 1
15 2
15
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE REQUIRED, THESE HOLES
MUST BE FIELD DRILLED AS NEEDED
GREEN
YELLOW
BLUE
WHITE
RED
14
19724
PART OF 12
9
PNEUMATIC TIMER SWITCH ASSEMBLY
TOP
71100A MOUNTING INSTRUCTIONS
BOX MUST BE INSTALLED
WITH "TOP" FACING UPWARD
THESE (4) HOLES MUST
BE DRILLED OUT USING
A 3/16 in. DRILL BIT
16
DRILL (4)
3/16 DIA. HOLES
17
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
VIEW SHOWING
TYPICAL FLUSH MOUNT
TO SINGLE GANG BOX
OPTIONAL IF IS NOT USED
14
SWITCH DATA
RATED VOLTAGE - 240 VAC 10 AMP.
(RESISTIVE LIFE CYCLES 1,000,000)
NC
NO
GREEN
YELLOW
BLUE
WHITE
RED
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
NC
NO
NC
NO
DRILL (4)
3/16 DIA. HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW, WHITE AND BLUE
19068 SCREW
SELF TAPPING (4) PROVIDED
19014 SCREW #8 X 1 (4) PROVIDED
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE NEEDED, THESE HOLES
MUST BE FIELD DRILLED AS REQUIRED.
19018 ANCHOR (4) PROVIDED
19021 GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE NOT PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
GROUND LUG
(2) PROVIDED
SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
4.87 in.
(124mm)
SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
1.62 in.
(41mm)
3.25 in. (82mm)
PRODUCT DIMENSIONS
DRILL (4)
3/16 DIA.
HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW,
WHITE AND BLUE
SCREW
SELF TAPPING
(4) PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
1.58 in.
(40mm)
1.375 in.
(35mm)
SCREW #8 X 1
(4) PROVIDED
IF WIRE ACCESS OR CONDUIT
ENTRY HOLES ARE NEEDED,
THESE HOLES MUST BE FIELD
DRILLED AS REQUIRED.
ANCHOR
(4) PROVIDED
GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE
NOT PROVIDED
19021 GROUND LUG
(2) PROVIDED
19060 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
TIMER RANGE ADJUSTMENT SCREW
* IF NEEDED, MAKE VERY SMALL
ADJUSTMENTS*
TURN COUNTER CLOCKWISE
TO INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
BUTTON AND SWITCH ASSEMBLY
WRENCH
(1) PROVIDED
SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
PUSH
PUSH
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
13 4
14 1
15 2
19724
PART OF 12
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO INCREASE TIMER SPEED
ADJUSTMENT RANGE – 2 TO 60 SECONDS
FACTORY SETTING – 25 TO 45 SECONDS
FAST
SLOW
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
1
2
3
4
5
6
7
89
10
10
11
12
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
10
PRODUCT DIMENSIONS
3.18 in. (81mm)
4.87 in.
(124mm)
3.25 in.(82mm) 1.62 in.(41mm)
13
13 4
14 1
15 2
15
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE REQUIRED, THESE HOLES
MUST BE FIELD DRILLED AS NEEDED
GREEN
YELLOW
BLUE
WHITE
RED
14
19724
PART OF 12
9
PNEUMATIC TIMER SWITCH ASSEMBLY
TOP
71100A MOUNTING INSTRUCTIONS
BOX MUST BE INSTALLED
WITH "TOP" FACING UPWARD
THESE (4) HOLES MUST
BE DRILLED OUT USING
A 3/16 in. DRILL BIT
16
DRILL (4)
3/16 DIA. HOLES
17
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
VIEW SHOWING
TYPICAL FLUSH MOUNT
TO SINGLE GANG BOX
OPTIONAL IF IS NOT USED
14
SWITCH DATA
RATED VOLTAGE - 240 VAC 10 AMP.
(RESISTIVE LIFE CYCLES 1,000,000)
NC
NO
GREEN
YELLOW
BLUE
WHITE
RED
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
NC
NO
NC
NO
DRILL (4)
3/16 DIA. HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW, WHITE AND BLUE
19068 SCREW
SELF TAPPING (4) PROVIDED
19014 SCREW #8 X 1 (4) PROVIDED
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE NEEDED, THESE HOLES
MUST BE FIELD DRILLED AS REQUIRED.
19018 ANCHOR (4) PROVIDED
19021 GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE NOT PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
GROUND LUG
(2) PROVIDED
SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
4.87 in.
(124mm)
SWITCH INFORMATION
LEAD WIRE COLORS
IN PARENTHESIS.

- 7 -
SCREW ALLEN HEAD
#8 - 32 x 3/8 (1) PROVIDED
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
1.62 in.
(41mm)
3.25 in. (82mm)
PRODUCT DIMENSIONS
DRILL (4)
3/16 DIA.
HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW,
WHITE AND BLUE
SCREW
SELF TAPPING
(4) PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
1.58 in.
(40mm)
1.375 in.
(35mm)
SCREW #8 X 1
(4) PROVIDED
IF WIRE ACCESS OR CONDUIT
ENTRY HOLES ARE NEEDED,
THESE HOLES MUST BE FIELD
DRILLED AS REQUIRED.
ANCHOR
(4) PROVIDED
GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE
NOT PROVIDED
19021 GROUND LUG
(2) PROVIDED
19060 SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
TIMER RANGE ADJUSTMENT SCREW
* IF NEEDED, MAKE VERY SMALL
ADJUSTMENTS*
TURN COUNTER CLOCKWISE
TO INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
BUTTON AND SWITCH ASSEMBLY
WRENCH
(1) PROVIDED
SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
PUSH
PUSH
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
13 4
14 1
15 2
19724
PART OF 12
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO INCREASE TIMER SPEED
ADJUSTMENT RANGE – 2 TO 60 SECONDS
FACTORY SETTING – 25 TO 45 SECONDS
FAST
SLOW
ITEM QTY. PART No. NAME
PART DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
2
1
1
10271
201001
2201014
201002
201005
201006
19001
SWITCH HOUSING
PUSH BUTTON
BUTTON SPRING
SHELL ASM.
PLUNGER
BACK PLATE ASM.
SCREW 8-32 x 3/8
3/32 ALLEN WRENCH
1
2
3
4
5
6
7
89
10
10
11
12
102601 SWITCH BRACKET
19021 GROUND LUG
3
NUT- SWITCH ASM.
PNEUMATIC SWITCH ASM.
19015
200890
10
PRODUCT DIMENSIONS
3.18 in. (81mm)
4.87 in.
(124mm)
3.25 in.(82mm) 1.62 in.(41mm)
13
13 4
14 1
15 2
15
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE REQUIRED, THESE HOLES
MUST BE FIELD DRILLED AS NEEDED
GREEN
YELLOW
BLUE
WHITE
RED
14
19724
PART OF 12
9
PNEUMATIC TIMER SWITCH ASSEMBLY
TOP
71100A MOUNTING INSTRUCTIONS
BOX MUST BE INSTALLED
WITH "TOP" FACING UPWARD
THESE (4) HOLES MUST
BE DRILLED OUT USING
A 3/16 in. DRILL BIT
16
DRILL (4)
3/16 DIA. HOLES
17
16
17
4
4
19014
19018
SCREW 8 x 1
ANCHOR
VIEW SHOWING
TYPICAL FLUSH MOUNT
TO SINGLE GANG BOX
OPTIONAL IF IS NOT USED
14
SWITCH DATA
RATED VOLTAGE - 240 VAC 10 AMP.
(RESISTIVE LIFE CYCLES 1,000,000)
NC
NO
GREEN
YELLOW
BLUE
WHITE
RED
71100A OUTLET BOX (SURFACE )
SCREWS 6-32 x 1. 00
19010
SCREW 3.5mm x 13mm
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
NC
NO
NC
NO
DRILL (4)
3/16 DIA. HOLES
71100A SURFACE BOX
RED, GREEN, YELLOW, WHITE AND BLUE
19068 SCREW
SELF TAPPING (4) PROVIDED
19014 SCREW #8 X 1 (4) PROVIDED
IF WIRE ACCESS OR CONDUIT ENTRY
HOLES ARE NEEDED, THESE HOLES
MUST BE FIELD DRILLED AS REQUIRED.
19018 ANCHOR (4) PROVIDED
19021 GROUND LUG
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND JUMPER WIRE NOT PROVIDED
TYPICAL FLUSH MOUNT
GANG BOX
GROUND LUG
(2) PROVIDED
SCREW
#6-32 X 1
(2) PROVIDED
BUTTON AND
SWITCH ASSEMBLY
CAN BE INSTALLED
ON ANY EXISTING
SINGLE GANG BOX
4.87 in.
(124mm)
3.18 (81mm)
1.62 (41mm)
3.25 (82mm)
4.87
(124mm)
PNEUMATIC OPERATED TIMER, OPENS
OR CLOSES CIRCUIT AFTER TIME DELAY.
NO ELECTRICITY TO OPERATE
10 AMP, FOR C CONTACTS
IDEAL FOR SECURITY APPLICATIONS
CORROSION RESISTANT BODY
ADJSTABLE TIME RANGE
PRODUCT DIMENSIONS
CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
FAST
SLOW
TIME RANGE ADJUSTMENT SCREW
TURN COUNTER CLOCKWISE TO
INCREASE TIMER SPEED.
ADJUSTMENT RANGE - 2 TO 60 SECONDS
FACTORY SETTING - 25 TO 45 SECONDS
SWITCH DATA
RESOLUTION: 2 TO 60 SECONDS
ACCURACY: 10% REPEAT ACCURACY
POWER: NONE TO OPERATE, SWITCHES
UP TO 10 AMPS @ 240 VOLTS
RESET: AT CYCLE END
LIFE CYCLES: 1,000,000
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
FAST
SLOW
NC
NO
PNEUMATIC TIMER
SWITCH ASSEMBLY
BACKPLATE WITH MOLDED-IN
STAINLESS STEEL INSERT
SWITCH HOUSING MOLDED OF
POLYCARBONATE. CHOOSE RED,
GREEN, YELLOW, WHITE OR BLUE.
ALLEN HEAD
LOCKING SCREW
AND WRENCH
ALSO CAN BE INSTALLED ON ANY
EXISTING SINGLE GANG BOX
BUTTON AND SWITCH ASSEMBLY
19015 WRENCH
(1) PROVIDED
FIGURE C
SURFACE BOX
INSTALLATION
19011 SCREW ALLEN HEAD
#8-32 x 3/8 (1) PROVIDED
10271 SWITCH HOUSING
RED, GREEN, YELLOW,
WHITE AND BLUE
1.62 in.
(41mm)
3.25 in. (82mm)
4.87 in.
(124mm)
PRODUCT DIMENSIONS
1.58 in.
(40mm)
1.375 in.
(35mm)
1.62 in.
(41mm)
3.25 in.(82mm)
4.87 in.
(124mm)
PRODUCT DIMENSIONS
1.56 in.
(40mm)
"A"
TO PROVIDE ADEQUATE CLEARANCE FOR CONTACTS,
(#0, #1, #3, #4) INSTALLATION
1.62 in.
(41mm)
3.25 in.(82mm)
4.87 in.
(124mm)
1.58 in.
(40mm)
"A"
GROUND SCREW
BUTTON AND SWITCH ASSEMBLY
SCREW #6-32 x 1 in.
(2) PROVIDED
SCREW #6 x 1-1/4 in.
(4) PROVIDED
KIT-71100A-COLOR SURFACE BOX
ANCHOR
(4) PROVIDED
DRILL (4) 3/16 in.
DIA HOLES
J
J
J
J
HSWITCH BACKPLATE
MOUNTING HOLES
BOX MUST BE INSTALLED WITH
ARROWS POINTING UPWARD
THESE HOLES MUST BE
DRILLED OUT USING A
5/32 in. DRILL BIT
H
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
19039 SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
19060 SCREW #6-32 x 1 in.
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
19021 GROUND SCREW
19018 ANCHOR
(4) PROVIDED
THIS VIEW FOR PAGE 6
DRILL (4)
3/16 DIA. HOLES
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
SCREW #6-32 x 1 in.
(2) PROVIDED
BUTTON AND SWITCH ASSEMBLY
GROUND SCREW
ANCHOR
(4) PROVIDED
THIS VIEW FOR PAGE 6
DRILL (4)
3/16 DIA. HOLES
BACKPLATE WITH MOLDED-IN
STAINLESS STEEL INSERT
SWITCH HOUSING MOLDED
OF POLYCARBONATE. CHOOSE
RED, GREEN, YELLOW,
WHITE OR BLUE.
ALLEN HEAD
LOCKING SCREW
AND WRENCH
DRILL POINT LOCATIONS PROVIDED
TOP AND BOTTOM FOR 1/2 in.
CONDUIT FITTINGS.
DRILL AS NEEDED
KIT-71100A BOX (SURFACE MOUNT)
RED, GREEN, YELLOW, WHITE AND BLUE
19039 SCREW #6 x 1-1/4 in.
(4) PROVIDED
PNEUMATIC TIMER MODEL
WITH PROVIDED
SURFACE BACKBOX
19060 SCREW #6-32 x 1 in.
(2) PROVIDED
19021
GROUND SCREW
19018 ANCHOR
(4) PROVIDED
DRILL (4)
3/16 DIA. HOLES
.728 in.
(18.49mm)
2.4 in.
(60.96mm)
3.218 in.
(81.74mm)
4.132 in.
(104.95mm)
4.83 in.
(122.68mm)
1.578 in.
(40.08mm)
INSTALLATION
WITH PROVIDED
SURFACE BACK BOX
WITHOUT PROVIDED
SURFACE BACK BOX
ADA mounting compliance
requires the operable part
of the initiating device shall
not be less than 1.1m (3 1/2
ft.) or greater than 1.37m (4
1/2 ft.) above nished oor
service.

2008 A-IS
WARRANTY
Three year guarantee against breakage of polycarbonate in normal use (one year on electro
mechanical and electronic components).
Electronic warranty form at www.sti-usa.com/wc14.
WARNING: This product can expose you to chemicals including Bisphenol A, which
is known to the State of California to cause reproductive harm and Dichloromethane,
which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov.
Taylor House • 34 Sherwood Road • Bromsgrove, Worcestershire • B60 3DR • England
Tel: [phone] • [email protected] • www.sti-emea.com
Unit 7A • Lockhead Avenue • Airport Business Park • Waterford • X91 HWF2 • Ireland
[email protected] • www.sti-emea.com
2306 Airport Rd • Waterford, MI 48327, USA
Phone: [phone] • [email protected] • www.sti-usa.com
June2015
EMEA
USA