STIEBEL ELTRON SBB 751 Instruction Manual

BEDIENUNG UND INSTALLATION
OPERATION AND INSTALLATION
UTILISATION ET INSTALLATION
BEDIENING EN INSTALLATIE
USO E INSTALLAZIONE
OBSLUHA A INSTALACE
Warmwasser-Standspeicher | Floorstanding DHW cylinder | Ballon ECS sur pied |
Staande warmwaterboiler | Acqua calda - Caldaia verticale | Stacionární zásobník
teplé vody
» SBB 751
» SBB 1001
» SBB 751 SOL
» SBB 1001 SOL

16 | SBB 751-1001 | SBB 751-1001 SOL WWW.STIEBEL-ELTRON.COM
CONTENTS | OPERATION
GENERAL INFORMATION
OPERATION
1. General information ��������������������������������������� 16
1.1 Safety instructions���������������������������������������������� 16
1.2 Other symbols in this documentation ���������������������� 17
1.3 Units of measurement ����������������������������������������� 17
2. Safety�������������������������������������������������������� 17
2.1 Intended use����������������������������������������������������� 17
2.2 General safety instructions ����������������������������������� 17
3. Appliance description ������������������������������������� 17
4. Cleaning, care and maintenance ������������������������� 18
5. Troubleshooting �������������������������������������������� 18
INSTALLATION
6. Safety�������������������������������������������������������� 19
6.1 General safety instructions ����������������������������������� 19
6.2 Regulations, standards and instructions������������������� 19
7. Appliance description ������������������������������������� 19
7.1 Standard delivery����������������������������������������������� 19
7.2 Accessories������������������������������������������������������� 19
8. Preparations������������������������������������������������ 19
8.1 Installation site�������������������������������������������������� 19
8.2 Transport ��������������������������������������������������������� 19
9. Preparing for installation ��������������������������������� 20
9.1 Fitting the thermal insulation, if appropriate������������� 20
9.2 Fitting the signal anode ��������������������������������������� 20
9.3 Fitting the thermometer and temperature sensor ������� 20
9.4 Fitting the heat transfer station, if appropriate ���������� 20
9.5 Fitting the flanged immersion heater, if appropriate ���20
9.6 Fitting the water connection and the safety assembly�� 20
9.7 Heating or solar installation���������������������������������� 21
10. Commissioning ��������������������������������������������� 21
10.1 Commissioning�������������������������������������������������� 21
10.2 Recommissioning����������������������������������������������� 21
11. Shutting down���������������������������������������������� 21
12. Troubleshooting �������������������������������������������� 21
13. Maintenance ������������������������������������������������ 21
13.1 Checking the safety valve ������������������������������������� 21
13.2 Draining the appliance ���������������������������������������� 21
13.3 Replacing the signal anode����������������������������������� 21
14. Specification ������������������������������������������������ 22
14.1 Dimensions and connections ��������������������������������� 22
14.2 Fault conditions ������������������������������������������������� 27
14.3 Data table �������������������������������������������������������� 27
GUARANTEE
ENVIRONMENT AND RECYCLING
OPERATION
1. General information
The chapter “Operation” is intended for appliance users and heat-
ing contractors.
The chapter “Installation” is intended for heating contractors.
Note Read these instructions carefully before using the appli-
ance and retain them for future reference.
Pass on the instructions to a new user if required.
1.1 Safety instructions
1.1.1 Structure of safety instructions
!KEYWORD Type of risk
Here, possible consequences are listed that may result
from failure to observe the safety instructions.
 Steps to prevent the risk are listed.
1.1.2 Symbols, type of risk
Symbol Type of risk
Injury
Electrocution
Burns
(burns, scalding)
1.1.3 Keywords
KEYWORD Meaning
DANGER Failure to observe this information will result in serious
injury or death.
WARNING Failure to observe this information may result in serious
injury or death.
CAUTION Failure to observe this information may result in non-
serious or minor injury.
!

OPERATION
SAFETY
ENGLISH
WWW.STIEBEL-ELTRON.COM SBB 751-1001 | SBB 751-1001 SOL | 17
1.2 Other symbols in this documentation
Note General information is identified by the symbol shown
on the left.
 Read these texts carefully.
Symbol Meaning
Material damage
(Appliance and consequential losses, environmental pol-
lution)
Appliance disposal
 This symbol indicates that you have to do something. The ac-
tion you need to take is described step by step.
1.3 Units of measurement
Note All measurements are given in mm unless stated oth-
erwise.
2. Safety
2.1 Intended use
The appliance is intended for heating and storing potable water
when operating a heat pump with a high output. The DHW and
cylinder are heated in combination with the WTS charging station
available as an accessory.
Suitable flanged immersion heaters can be fitted by a heating
contractor.
Any other use beyond that described shall be deemed inappropri-
ate. Observation of these instructions and of instructions for any
accessories used is also part of the correct use of this appliance.
2.2 General safety instructions
WARNING Burns There is a risk of scalding at outlet temperatures in ex-
cess of 43 °C.
!WARNING Injury
Where children or persons with limited physical, sensory
or mental abilities are allowed to control this appliance,
ensure that this will only happen under supervision or
after appropriate instruction by a person responsible
for their safety.
Children should be supervised to ensure that they never
play with the appliance!
Note The appliance is under pressure.
During the heat-up process, expansion water will drip
from the safety valve. If water continues to drip when
the heat-up process is completed, please inform your
qualified contractor.
3. Appliance description
The internal steel cylinder is coated in “anticor®” enamel and is
equipped with a signal anode to protect the inside of the cylinder
against corrosion.
SBB 751 SOL and SBB 1001 SOL
These appliance types are additionally equipped with an indirect
coil for heating with solar energy.
!

OPERATION
CLEANING, CARE AND MAINTENANCE
18 | SBB 751-1001 | SBB 751-1001 SOL WWW.STIEBEL-ELTRON.COM
4. Cleaning, care and maintenance
 Have a contractor regularly check the appliance, the safety
assembly and all fitted accessories.
 Never use abrasive or corrosive cleaning agents. A damp
cloth is sufficient for cleaning all plastic parts.
Protective anode
!Material damage
If the consumption indicator changes colour from white to
red, have the signal anode checked by a heating contrac-
tor and if necessary replaced.
12
26�03�01�1345
Signal anode consumption indicator
1 white = anode OK
2 Red = check by heating contractor required
Scaling
 Almost every type of water deposits limescale at high tem-
peratures. This settles inside the appliance and affects both
the performance and service life. The indirect coils and fitted
accessories should therefore be descaled from time to time.
A heating contractor who knows the local water quality will
tell you when the next service is due.
5. Troubleshooting
Telephone your contractor.
To facilitate and speed up your enquiry, please provide the serial
number from the type plate (000000-0000-000000):
26�03�01�1353

ENGLISH
WWW.STIEBEL-ELTRON.COM SBB 751-1001 | SBB 751-1001 SOL| 19
INSTALLATION
SAFETY
INSTALLATION
6. Safety
Only a qualified contractor should carry out installation, commis-
sioning, maintenance and repair of the appliance.
6.1 General safety instructions
We can only guarantee trouble-free function and operational reli-
ability if original spare parts intended for the appliance are used.
6.2 Regulations, standards and instructions
Note Observe all applicable national and regional regulations
and instructions.
7. Appliance description
7.1 Standard delivery
Delivered with the appliance:
- Signal anode
- Temperature sensors
- Heat conducting paste
- Thermometer
- additional type plate
- Label “Signal anode information”
7.2 Accessories
7.2.1 SVGW-approved accessories
Charging station
Heat transfer stations absorb heating circuit energy by means
of a plate heat exchanger. Heating energy for DHW heating is
transferred into the cylinder primary circuit. The heat transfer
stations are equipped with one circulation pump for each of these
circumstances.
7.2.2 Further accessories
Safety assemblies and pressure reducing valves
Depending on the static pressure, safety assemblies and pressure
reducing valves are available. These type-tested safety assemblies
protect the appliance against unacceptable excess pressure.
Flanged immersion heaters and thermal insulation
In addition, flanged immersion heaters and thermal insulation are
available as accessories.
8. Preparations
8.1 Installation site
 Always install the appliance in a room free from the risk of
frost and near the draw-off point.
 Ensure that the floor is even and has sufficient load bear-
ing capacity and check the height of the room (see chapter
“Specification / Data table”).
Minimum clearances
≥400 ≥175
≥600≥200
≥800
D0000057344
The minimum side clearances can be swapped to left or right.
 Observe minimum distances.
8.2 Transport
Use the lifting eyes at the top of the appliance to assist handling.

20 | SBB 751-1001 | SBB 751-1001 SOL WWW.STIEBEL-ELTRON.COM
INSTALLATION
PREPARING FOR INSTALLATION
9. Preparing for installation
9.1 Fitting the thermal insulation, if appropriate
 Position the appliance in its intended site.
 Fit the thermal insulation according to the instructions sup-
plied. For this, ensure that there is enough space for the
installation task. You can then link the appliance into the
heating and DHW system.
9.2 Fitting the signal anode
!Material damage
When operating the cylinder without consumption indica-
tor, leave the plug in the threaded hole.
26�02�09�0031
 Pull the plug out by simultaneously pushing the pressure
ring down.
 Push the open pipe end of the consumption indicator into the
aperture of the anode.
9.3 Fitting the thermometer and temperature
sensor
 Insert the thermometer as far as it will go and align it.
 Insert the temperature sensor into the sensor pipe as far as it
will go. Apply heat conducting paste.
9.4 Fitting the heat transfer station, if appropriate
 Install the charging station in accordance with the operating
and installation instructions supplied.
9.5 Fitting the flanged immersion heater, if
appropriate
 Remove the dummy flanges to install flanged immersion
heaters in accordance with the operating and installation in-
structions supplied. Maintain the DC separation towards the
cylinder.
9.6 Fitting the water connection and the safety
assembly
9.6.1 Safety instructions
Note Carry out all water connection and installation work in
accordance with regulations.
!Material damage
If a flanged immersion heater is fitted and plastic pipe-
work is used at the same time, observe chapter “Speci-
fication/ Fault conditions”.
!Material damage
Operate the appliance only with pressure-tested taps and
valves.
Cold water line
Copper, steel or plastic pipework are approved materials.
!Material damage
A safety valve is required.
DHW line
Copper or plastic pipework are approved materials.
9.6.2 Water connection
 Flush the line thoroughly.
 Install a type-tested safety assembly. Bear in mind that, de-
pending on the static pressure, you may also need a pressure
reducing valve.
 Connect the DHW outlet line and the cold water inlet line.
 Size the drain so that water can drain off unimpeded when
the safety valve is fully opened. The blow-off aperture of the
safety valve must remain open to the atmosphere.
 Fit the blow-off line of the safety assembly with a constant
slope.
 Observe the information in the installation instructions of the
safety assembly.

ENGLISH
WWW.STIEBEL-ELTRON.COM SBB 751-1001 | SBB 751-1001 SOL| 21
INSTALLATION
COMMISSIONING
9.7 Heating or solar installation
9.7.1 Water quality, solar circuit
A glycol/water mixture of up to 60% is permitted for the indirect
coil in the solar circuit if only dezincification-resistant metals,
glycol-resistant gaskets and diaphragm expansion vessels suitable
for glycol are used throughout the installation.
9.7.2 Oxygen diffusion
!Material losses
Avoid open heating systems and plastic pipes in under-
floor heating systems which are permeable to oxygen.
In underfloor heating systems with plastic pipes that are per-
meable to oxygen and in open vented heating systems, oxygen
diffusion may lead to corrosion on the steel components of the
heating system (e.g. on the indirect coil of the DHW cylinder, on
buffer cylinders, steel heating elements or steel pipes).
!Material losses
The products of corrosion (e.g. rusty sludge) can settle in
the heating system components and can result in a lower
output or fault shutdowns due to reduced cross-sections.
!Material losses
Avoid open vented solar thermal systems and plastic
pipes which are permeable to oxygen.
With plastic pipes that are permeable to oxygen, oxygen diffusion
may lead to corrosion on the steel components of the solar thermal
system (e.g. on the indirect coil of the DHW cylinder).
10. Commissioning
10.1 Commissioning
 Open a draw-off point until the appliance has filled up and
the pipework is free of air.
 Adjust the flow rate. For this, observe the maximum permis-
sible flow rate with a fully opened tap (see chapter “Specifi-
cation / Data table”). If necessary reduce the flow rate at the
butterfly valve of the safety assembly.
 Carry out a tightness check.
 Switch the mains power ON if required.
 Check the function of the fitted accessories.
 Check the function of the safety assembly.
SBB 751 SOL | SBB 1001 SOL
 Thoroughly flush the indirect coil with water before connect-
ing the solar thermal system.
10.1.1 Appliance handover
 Explain the appliance function to users and familiarise them
with its operation.
 Make users aware of potential dangers, especially the risk of
scalding.
 Hand over these instructions.
10.2 Recommissioning
See chapter “Commissioning”.
11. Shutting down
 Drain the appliance. See chapter “Maintenance / Draining the
appliance”.
12. Troubleshooting
Fault Cause Remedy
The safety valve drips
when the heating is
switched off.
The valve seat is con-
taminated.
Clean the valve seat.
13. Maintenance
WARNING Electrocution Carry out all electrical connection and installation work
in accordance with relevant regulations.
WARNING Electrocution Before any work on the appliance, disconnect all poles
of the appliance from the power supply.
If you need to drain the appliance, observe chapter “Draining the
appliance”.
13.1 Checking the safety valve
 Regularly vent the safety valve on the safety assembly until a
full water jet is discharged.
13.2 Draining the appliance
WARNING Burns Hot water may escape during the draining process.
If the appliance needs to be drained for maintenance or to protect
the whole installation when there is a risk of frost, proceed as
follows:
 Close the shut-off valve in the cold water inlet pipe.
 Open the hot water taps on all draw-off points.
 Drain the appliance via the charging station return (see chap-
ter “Specification / Dimensions and connections”). Please
note that residual water remains in the appliance.
13.3 Replacing the signal anode
 Replace the signal anode if it becomes depleted. Observe
the maximum permissible transition resistance between the
anode and the cylinder 0.3 Ω.

22 | SBB 751-1001 | SBB 751-1001 SOL WWW.STIEBEL-ELTRON.COM
INSTALLATION
SPECIFICATION
14. Specification
14.1 Dimensions and connections
SBB 751
i18
c06
d21
c01
c10
d22
h43
i03
h06
h05
h06
i02
d35
d24
d36
D0000020368
SBB 751
c01 Cold water inlet Male thread G 2 A
c06 DHW outlet Male thread G 2 A
c10 DHW circulation Male thread G 1 A
d21 Charging station flow Male thread G 2 A
d22 Charging station return Male thread G 2 A
d24 Charging station return opt. Male thread G 2 A
d35 Heat source flow optional Male thread G 2 A
d36 Heat source return optional Male thread G 2 A
h05 Sensor heat pump DHW Diameter mm 9.5
h06 Sensor heat pump DHW optional Diameter mm 9.5
h43 Thermometer Diameter mm 14.5
i02 Flange 1 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i03 Flange2 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i18 Protective anode Female thread G 1 1/4

ENGLISH
WWW.STIEBEL-ELTRON.COM SBB 751-1001 | SBB 751-1001 SOL | 23
INSTALLATION
SPECIFICATION
SBB 1001
c06
c01
d22 d36
c10
h43
h06
i03
h05
h06
i02
d21
d24
d35
i18
D0000017401
SBB 1001
c01 Cold water inlet Male thread G 2 A
c06 DHW outlet Male thread G 2 A
c10 DHW circulation Male thread G 1 A
d21 Charging station flow Male thread G 2 A
d22 Charging station return Male thread G 2 A
d24 Charging station return opt. Male thread G 2 A
d35 Heat source flow optional Male thread G 2 A
d36 Heat source return optional Male thread G 2 A
h05 Sensor heat pump DHW Diameter mm 9.5
h06 Sensor heat pump DHW optional Diameter mm 9.5
h43 Thermometer Diameter mm 14.5
i02 Flange 1 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i03 Flange2 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i18 Protective anode Female thread G 1 1/4

24 | SBB 751-1001 | SBB 751-1001 SOL WWW.STIEBEL-ELTRON.COM
INSTALLATION
SPECIFICATION
SBB 751 SOL
i18
h43
h06
i03
h05
h06
h28
i02
d21
c06
d26 d22
c01
d25
c10
D0000017355
SBB 751 SOL
c01 Cold water inlet Male thread G 2 A
c06 DHW outlet Male thread G 2 A
c10 DHW circulation Male thread G 1 A
d21 Charging station flow Male thread G 2 A
d22 Charging station return Male thread G 2 A
d25 Solar flow Female thread G 1
d26 Solar return Female thread G 1
h05 Sensor heat pump DHW Diameter mm 9.5
h06 Sensor heat pump DHW optional Diameter mm 9.5
h28 Sensor solar cylinder Diameter mm 9.5
h43 Thermometer Diameter mm 14.5
i02 Flange 1 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i03 Flange2 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i18 Protective anode Female thread G 1 1/4

ENGLISH
WWW.STIEBEL-ELTRON.COM SBB 751-1001 | SBB 751-1001 SOL| 25
INSTALLATION
SPECIFICATION
SBB 1001 SOL
c06
c01
h43
h06
i03
h05
h06
i02
d21
h28
d26
d25
c10
i18
i18
d22
D0000017403
SBB 1001 SOL
c01 Cold water inlet Male thread G 2 A
c06 DHW outlet Male thread G 2 A
c10 DHW circulation Male thread G 1 A
d21 Charging station flow Male thread G 2 A
d22 Charging station return Male thread G 2 A
d25 Solar flow Female thread G 1
d26 Solar return Female thread G 1
h05 Sensor heat pump DHW Diameter mm 9.5
h06 Sensor heat pump DHW optional Diameter mm 9.5
h28 Sensor solar cylinder Diameter mm 9.5
h43 Thermometer Diameter mm 14.5
i02 Flange 1 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i03 Flange2 Diameter mm 280
Pitch circle diameter mm 245
Screws M 14
Torque Nm 80
i18 Protective anode Female thread G 1 1/4

26 | SBB 751-1001 | SBB 751-1001 SOL WWW.STIEBEL-ELTRON.COM
INSTALLATION
SPECIFICATION
Appliance cross-section SBB 751 SOL | SBB 1001 SOL
c06
c01
d26
d25
c10
h43
i03
i02
26�03�01�1371
h06
h05
h06
d21
h28
d22
26�03�01�1375
14.2 Fault conditions
In the event of a fault, temperatures of up to 95 °C at 1.0 MPa can
occur depending on the type of heart source used.

ENGLISH
WWW.STIEBEL-ELTRON.COM SBB 751-1001 | SBB 751-1001 SOL | 27
GUARANTEE
ENVIRONMENT AND RECYCLING
14.3 Data table
SBB 751 SBB 1001 SBB 751 SOL SBB 1001 SOL
229292 229293 229294 229295
Hydraulic data
Nominal capacity l763 1004 736 971
Capacity, lower indirect coil l 20.5 25.2
Surface area, lower indirect coil m² 3 4.0
Pressure drop at 1.0 m³/h, lower indirect coil hPa 39 52
Mixed water volume at 40°C (15°C/60°C) l 1264 1650 1230 1599
Application limits
Max. permissible pressure MPa 1 1 1 1
Test pressure MPa 1.5 1.5 1.5 1.5
Max. permissible temperature °C 95 95 95 95
Max. flow rate l/min 90 90 90 90
Max. recommended collector aperture area m² 15 20
Dimensions
Height mm 1777 2277 1777 2277
Diameter mm 790 790 790 790
Diameter incl. thermal insulation mm 1010 1010 1010 1010
Height when tilted mm 1840 2335 1840 2335
Weights
Weight, full kg 960 1267 971 1296
Weight, empty kg 210 267 242 296
INSTALLATION | GUARANTEE | ENVIRONMENT AND RECYCLING
SPECIFICATION
GUARANTEE
ENVIRONMENT AND RECYCLING
Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only grant-
ed if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.



Deutschland
STIEBEL ELTRON GmbH & Co. KG
Dr.-Stiebel-Straße 33 | 37603 Holzminden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.de
Verkauf Tel. [phone] | Fax [phone] | [email protected]
Kundendienst Tel. [phone] | Fax [phone] | [email protected]
Ersatzteilverkauf Tel. [phone] | Fax [phone] | [email protected]
Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve
d‘erreurs et de modifications techniques! | Onder voorbehoud van ver
g
issin
g
en en technische wi
j
zi
g
in
g
en! |
Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmian
y
techniczne i
ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések
j
o
g
át
fenntartjuk! | Отсутствие ошибок не гарантируется. Возможны технические изменения. | Ch
y
b
y
a
technické zmeny sú vyhradené! Stand 9046
Australia
STIEBEL ELTRON Australia Pty. Ltd.
6 Prohasky Street | Port Melbourne VIC 3207
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel.com.au
Austria
STIEBEL ELTRON Ges.m.b.H.
Eferdinger Str. 73 | 4600 Wels
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.at
Belgium
STIEBEL ELTRON bvba/sprl
't Hofveld 6 - D1 | 1702 Groot-Bijgaarden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.be
China
STIEBEL ELTRON (Guangzhou) Electric
Appliance Co., Ltd.
Rm 102, F1, Yingbin-Yihao Mansion, No. 1
Yingbin Road
Panyu District | 511431 Guangzhou
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltron.cn
Czech Republic
STIEBEL ELTRON spol. s r.o.
K Hájům 946 | 155 00 Praha 5 - Stodůlky
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.cz
Finland
STIEBEL ELTRON OY
Kapinakuja 1 | 04600 Mäntsälä
Tel. [phone]
[email protected]
www.stiebel-eltron.fi
France
STIEBEL ELTRON SAS
7-9, rue des Selliers
B.P 85107 | 57073 Metz-Cédex 3
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.fr
Hungary
STIEBEL ELTRON Kft.
Gyár u. 2 | 2040 Budaörs
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.hu
Japan
NIHON STIEBEL Co. Ltd.
Kowa Kawasaki Nishiguchi Building 8F
66-2 Horikawa-Cho
Saiwai-Ku | 212-0013 Kawasaki
Tel. [phone] | Fax [phone]
[email protected]
www.nihonstiebel.co.jp
Netherlands
STIEBEL ELTRON Nederland B.V.
Daviottenweg 36 | 5222 BH 's-Hertogenbosch
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.nl
Poland
STIEBEL ELTRON Polska Sp. z O.O.
ul. Działkowa 2 | 02-234 Warszawa
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.pl
Russia
STIEBEL ELTRON LLC RUSSIA
Urzhumskaya street 4,
building 2 | 129343 Moscow
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ru
Slovakia
TATRAMAT - ohrievače vody s.r.o.
Hlavná 1 | 058 01 Poprad
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.sk
Switzerland
STIEBEL ELTRON AG
Industrie West
Gass 8 | 5242 Lupfig
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ch
Thailand
STIEBEL ELTRON Asia Ltd.
469 Moo 2 Tambol Klong-Jik
Amphur Bangpa-In | 13160 Ayutthaya
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltronasia.com
United Kingdom and Ireland
STIEBEL ELTRON UK Ltd.
Unit 12 Stadium Court
Stadium Road | CH62 3RP Bromborough
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.co.uk
United States of America
STIEBEL ELTRON, Inc.
17 West Street | 01088 West Hatfield MA
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron-usa.com
A 290889-38920-9063
4<AMHCMN=jaiijb>