STIEBEL ELTRON DNM 3 Instruction Manual

Hydraulisch gesteuerter druckloser Mini-Durchlauferhitzer | Hydraulically controlled,
non-pressurised mini instantaneous water heater | Mini chauffe-eau instantané et à
écoulement libre à gestion hydraulique | Hydraulisch gestuurde drukloze mini-doorstromer
| Hydraulicznie sterowany bezciśnieniowy mini przepływowy ogrzewacz | Malý hydraulicky
řízený beztlakový průtokový ohřívač| Hydraulicky riadený mini prietokový ohrievač | Mini
încălzitor instant controlat electronic | Малогабаритный безнапорный проточный нагреватель с
гидравлическим управлением
» DNM 3
» DNM 4
» DNM 6
BEDIENUNG UND INSTALLATION
OPERATION AND INSTALLATION
UTILISATION ET INSTALLATION
BEDIENING EN INSTALLATIE
OBSŁUGA I INSTALACJA
OBSLUHA A INSTALACE
OBSLUHA A INŠTALÁCIA
OPERAREA ŞI INSTALAREA
ЭКСПЛУАТАЦИЯ И МОНТАЖ

24 | DNM www.stiebel-eltron.com

SPECIAL INFORMATION
OPERATION
1. General information ��������������������������������������� 25
2. Safety�������������������������������������������������������� 27
3. Appliance description ������������������������������������� 28
4. Settings ����������������������������������������������������� 28
5. Cleaning, care and maintenance ������������������������� 28
6. Troubleshooting �������������������������������������������� 29
INSTALLATION
7. Safety�������������������������������������������������������� 29
8. Appliance description ������������������������������������� 30
9. Preparations������������������������������������������������ 30
10. Installation�������������������������������������������������� 31
11. Commissioning ��������������������������������������������� 34
12. Appliance shutdown��������������������������������������� 35
13. Troubleshooting �������������������������������������������� 35
14. Maintenance ������������������������������������������������ 35
15. Specification ������������������������������������������������ 36
GUARANTEE
ENVIRONMENT AND RECYCLING

- The appliance may be used by children aged 3
and older and persons with reduced physical,
sensory or mental capabilities or a lack of ex-
perience and know-how, provided that they are
supervised or they have been instructed on how
to use the appliance safely and have understood
the resulting risks. Children must never play with
the appliance. Children must never clean the ap-
pliance or perform user maintenance unless they
are supervised.
- During operation, the tap can reach temperatures
in excess of 50 °C. There is a risk of scalding at
outlet temperatures in excess of 43°C.
- Ensure the appliance can be separated from the
power supply by an isolator that disconnects all
poles with at least 3mm contact separation.
- The specified voltage must match the mains
voltage.

ENGLISH
www.stiebel-eltron.com DNM | 25
OPERATION
General information
- The power cable must only be replaced (for ex-
ample if damaged) by a qualified contractor au-
thorised by the manufacturer, using an original
spare part.
- Secure the appliance as described in chapter "In-
stallation/ Installation".
- Observe the maximum permissible pressure (see
chapter "Specification/ Data table").
- The specific water resistivity of the mains water
supply must not be undershot (see chapter “In-
stallation / Specification / Data table”).
- Drain the appliance as described in chapter "In-
stallation/ Maintenance/ Draining the appliance".
OPERATION
1. General information
The chapter "Operation" is intended for appliance users and qual-
ified contractors.
The chapter "Installation" is intended for qualified contractors.
Note Read these instructions carefully before using the appli-
ance and retain them for future reference.
Pass on the instructions to a new user if required.
1.1 Safety instructions
1.1.1 Structure of safety instructions
KEYWORD Type of risk Here, possible consequences are listed that may result
from failure to observe the safety instructions.
 Steps to prevent the risk are listed.

OPERATION
General information
26 | DNM www.stiebel-eltron.com
1.1.2 Symbols, type of risk
Symbol Type of risk
Injury
Electrocution
Burns (burns, scalding)
1.1.3 Keywords
 Meaning
DANGER Failure to observe this information will result in serious
injury or death.
WARNING Failure to observe this information may result in serious
injury or death.
CAUTION Failure to observe this information may result in non-seri-
ous or minor injury.
1.2 Other symbols in this documentation
Note Notes are bordered by horizontal lines above and below
the text. General information is identified by the adjacent
symbol.
 Read these texts carefully.
Symbol
Material losses (appliance damage, consequential losses and environmen-
tal pollution)
Appliance disposal
 This symbol indicates that you have to do something. The ac-
tion you need to take is described step by step.
1.3 Units of measurement
Note Unless specified otherwise, all dimensions are given in
mm.
!
!

ENGLISH
www.stiebel-eltron.com DNM | 27
OPERATION
Safety
2. Safety
2.1 Intended use
The appliance is intended for domestic use. It can be used safely
by untrained persons. The appliance can also be used in a non-do-
mestic environment, e.g. in a small business, as long as it is used
in the same way.
This appliance is designed to heat DHW. The appliance is designed
for one hand washbasin.
Any other use beyond that described shall be deemed inappro-
priate. Observation of these instructions and of the instructions
for any accessories used is also part of the correct use of this
appliance.
2.2 General safety instructions
DANGER Scalding During operation, the tap can reach temperatures in ex-
cess of 50 °C.
There is a risk of scalding at outlet temperatures in ex-
cess of 43 °C.
!WARNING Injury
The appliance may be used by children aged 3 and older
and persons with reduced physical, sensory or mental
capabilities or a lack of experience and know-how, pro-
vided that they are supervised or they have been in-
structed on how to use the appliance safely and have
understood the resulting risks. Children must never play
with the appliance. Children must never clean the ap-
pliance or perform user maintenance unless they are
supervised.
DANGER Electrocution Any damaged power cables must be replaced by a qual-
ified electrician. This prevents potential hazards from
arising.
!Material losses
Protect the appliance and tap against frost.

OPERATION
Appliance description
28 | DNM www.stiebel-eltron.com
!Material losses
Ensure that the non-pressurised appliance is not exposed
to any pressure as this could cause irreparable damage:
 Only use the special aerator provided.
 Never use aerators or hoses with aerators.
 Never seal the tap outlets.
 Prevent scale build-up at the tap outlets (see chapter
"Cleaning, care and maintenance").
2.3 Test symbols
See type plate on the appliance.
3. Appliance description
The hydraulically controlled, non-pressurised mini instantaneous
water heater heats the water directly at the draw-off point. The
heating system starts automatically when the tap is opened. The
short pipe runs ensure that energy and water losses are minimal.
The DHW output depends on the cold water temperature, the heat-
ing output and the flow rate.
The bare wire heating system is suitable for hard and soft water
areas. This heating system has a low susceptibility to scale build-
up. The heating system ensures quick and efficient DHW provision
at the hand washbasin.
Fitting the special aerator supplied provides an optimum water jet.
4. Settings
The appliance heating system switches on automatically as soon
as you open the DHW valve at the tap or activate the sensor of a
sensor tap. The water is heated. The water temperature can be
adjusted at the tap:
For the start volume, see chapter "Specification/ Data table/ On".
Increasing the temperature
 Reduce the flow rate at the tap.
Reducing the temperature
 Open the tap further or add more cold water.
Following an interruption to the water supply
See chapter "Commissioning/ Recommissioning".
5. Cleaning, care and maintenance
 Never use abrasive or corrosive cleaning agents. A damp
cloth is sufficient for cleaning the appliance.
!Material losses
Scale build-up at the tap outlets can put the appliance
under pressure and may cause irreparable damage.

ENGLISH
www.stiebel-eltron.com DNM | 29
INSTALLATION
Troubleshooting
 Check the taps regularly. Limescale deposits at the tap out-
lets can be removed using commercially available descaling
agents.
 Have the electrical safety of the appliance regularly checked
by a qualified contractor.
 Regularly descale or replace the special aerator (see chapter
"Appliance description/Accessories").
6. Troubleshooting
Problem  Remedy
The appliance will not
start despite the DHW
valve being fully open.
No power at the appli-
ance. Check the fuse/MCB in your fuse box/distribu-
tion board.
The aerator in the tap is
scaled up or dirty. Clean and/or descale the aerator or replace the
special aerator.
The water supply has been interrupted. Vent the appliance and the cold water inlet line
(see chapter "Settings").
If you cannot remedy the fault, notify your contractor. To facilitate
and speed up your request, provide the number from the type
plate (000000-0000-000000).
DNM . . No.: 000000-0000-000000
INSTALLATION
7. Safety
Only a qualified contractor should carry out installation, commis-
sioning, maintenance and repair of the appliance.
7.1 General safety instructions
We guarantee trouble-free function and operational reliability only
if original accessories and spare parts intended for the appliance
are used.
!Material losses
Observe the max. permissible inlet temperature. Higher
temperatures may damage the appliance. You can limit
the inlet temperature by means of a central thermostatic
valve (see chapter "Appliance description/ Accessories").
!Material losses
Only operate the appliance with non-pressurised taps.

INSTALLATION
Appliance description
30 | DNM www.stiebel-eltron.com
7.2 Instructions, standards and regulations
Note Observe all applicable national and regional regulations
and instructions.
The specific electrical resistance of the water must not fall below
that stated on the type plate. In a linked water network, factor in
the lowest electrical resistance of the water (see chapter "Speci-
fication/ Data table"). Your water supply utility will advise you of
the specific electrical water resistance or conductivity.
8. Appliance description
8.1 Standard delivery
The following are delivered with the appliance:
- Sieve inside the cold water inlet
- Special aerator "SR"
- Company logo for oversink installation
8.2 Accessories
Special aerator "SR"*
- SR 3: Part number 289591
for DHM 3 and DHM 4
- SR 5: Part number 270582
for DHM 6 and DHM 7
* For use in thread M22/M24.
Non-pressurised taps
- WEN Sensor tap for washbasins
- MAW Wall mounted tap for oversink installation
- MAZ Twin-lever basin tap
- MAE Mono lever basin tap
ZTA 3/4 - central thermostatic valve
Thermostatic valve for central premixing, for example for operat-
ing an instantaneous water heater with a solar thermal system.
9. Preparations
 Flush the water line thoroughly.
Water installation
No safety valve is required.
Taps/valves
 Use suitable taps (see chapter "Appliance description/
Accessories").

ENGLISH
www.stiebel-eltron.com DNM | 31
INSTALLATION
Installation
Note Fitting the special aerator supplied provides an optimum
water jet.
10. Installation
10.1 Installation location
Install the appliance in a room free from the risk of frost and near
the draw-off tap.
Ensure that the lateral fixing screws for the cover are always ac-
cessible.
The appliance is suitable for undersink installation (water con-
nections at the top) and oversink installation (water connections
at the bottom).
DANGER Electrocution Protection rating IP 25 is only ensured if the appliance
back panel is fitted.
 Always fit the appliance back panel.
10.2 Installation options
10.2.1 Undersink installation, non-pressurised, with non-
pressurised tap
26_02_05_0080
Appliance installation
 Mount the appliance on the wall.
Note The wall must have sufficient load bearing capacity.

INSTALLATION
Installation
32 | DNM www.stiebel-eltron.com



26_02_05_0083
 Undo the cover fixing screws by two turns.
 Undo the snap fastener using a screwdriver.
 Remove the appliance cover with the heater towards the
front.


26_02_05_0084
 Using pliers, break out the knock-out for the power cable
in the appliance cover. Correct the contours with a file if
necessary.
 Use the appliance back panel as a drilling template.
 Secure the appliance back panel to the wall with suitable
rawl plugs and screws.

ENGLISH
www.stiebel-eltron.com DNM | 33
INSTALLATION
Installation



26_02_05_0085
 Route the power cable through the cable entry in the back
panel.
 Hook in the appliance cover with the heater at the bottom.
 Click the heater into place using the snap fastener.
 Secure the appliance cover with the cover fixing screws.
Tap installation
!Material losses
When making the connections, counter the torque on the
appliance using a size 14 spanner.
 Install the tap. For this, also observe the tap operating and
installation instructions.
10.2.2 Oversink installation, non-pressurised, with non-
pressurised tap
26_02_05_0081_
Tap installation
 Install the tap. For this, also observe the tap operating and
installation instructions.
!Material losses
 When making the connections, counter the torque
on the appliance using a size 14 spanner; see chap-
ter "Installation alternatives/ Undersink installa-
tion".
Appliance installation
 Fit the appliance to the tap with the water connections.

INSTALLATION

34 | DNM www.stiebel-eltron.com
10.3 Making the electrical connection
DANGER Electrocution Carry out all electrical connection and installation work
in accordance with relevant regulations.
DANGER Electrocution Ensure that the appliance is earthed.
Ensure the appliance can be separated from the power
supply by an isolator that disconnects all poles with at
least 3mm contact separation.
DANGER Electrocution The appliances are delivered with a power cable (DNM3
with plug).
Connection to a permanent power supply is possible,
provided the fixed cable has a cross-section that is at
least equal to that of the standard power cable of the
appliance. A maximum cross-section of 3 x 6 mm² may
be used..
 If the appliance is installed over the sink, route the
power cable behind the appliance.
!Material losses
When making the connection to a standard safety socket
(in the case of a power cable with plug), ensure that the
socket is freely accessible after the appliance has been
installed.
!Material losses
Observe the type plate. The specified voltage must match
the mains voltage.
 Connect the power cable as shown in the wiring diagram
(see chapter "Specification/ Wiring diagram").
11. Commissioning
11.1 Initial start-up
26_02_05_0087
 Fill the appliance by running the tap several times until the
pipework and appliance are free of air.
 Carry out a tightness check.
 Insert the power cable plug, if present, into the standard
safety socket or set the fuse/MCB.
 Check the appliance function.
 In the case of oversink installation, affix the company logo
supplied over the existing company logo.

ENGLISH
www.stiebel-eltron.com DNM | 35
INSTALLATION
Appliance shutdown
11.2 Appliance handover
 Explain the appliance function to users and familiarise them
with its operation.
 Make the user aware of potential dangers, especially the risk
of scalding.
 Hand over these instructions.
11.3 Recommissioning
!Material losses
Following an interruption of the water supply, recommis-
sion the appliance by carrying out the following steps,
in order to prevent irreparable damage to the bare wire
heating system.
 Isolate the appliance from the power supply. Pull the power
cable plug, if present, from the socket, or remove the fuse/
reset the MCB.
 See chapter "Commissioning".
12. Appliance shutdown
 Isolate the appliance from the power supply by means of the
fuse/MCB in your fuse box or by pulling the power cable plug
from the socket.
 Drain the appliance (see chapter "Maintenance").
13. Troubleshooting
Problem  Remedy
The appliance will not
start despite the DHW
valve being fully open.
The aerator in the tap is
scaled up or dirty. Clean and/or descale the aerator or replace the
special aerator.
The sieve in the cold
water line is blocked. Clean the sieve after shutting off the cold
water inlet line.
The heating system is
faulty.
Check the resistance of
the heating system and
replace the appliance if
required.
14. Maintenance
DANGER Electrocution Before any work on the appliance, ensure omnipolar
disconnection from the power supply.
Draining the appliance
DANGER Scalding Hot water may escape during draining.
If the appliance needs to be drained for maintenance or to protect
the whole installation when there is a risk of frost, proceed as
follows:

INSTALLATION

36 | DNM www.stiebel-eltron.com
 Close the shut-off valve in the cold water inlet line.
 Open the draw-off valve.
 Undo the water connections on the appliance.
Cleaning the strainer
You can clean the fitted strainer after removing the cold water
supply pipe.
26_02_05_0065_
Checking the earth conductor
 Check the earth conductor (in Germany e.g. BGV A3) on the
earth conductor contact of the power cable and on the appli-
ance connector.
Appliance storage
 Store the dismantled appliance in a room free from the risk
of frost, as water residues remaining inside the appliance can
freeze and cause damage.
Replacing the power cable for the DNM 6
 When replacing the cable for the DNM 6, use a power cable
with 4 mm² cross-section.
15. Specification
15.1 Dimensions and connections
95
28
30
120
143
190
4,8
165
82
20
b02
b03
c06
c01
D0000018336
DNM
b02 Entry electrical cables I
b03 Entry electrical cables II
c01 Cold water inlet Male thread G 3/8 A
c06 DHW outlet Male thread G 3/8 A

ENGLISH
www.stiebel-eltron.com DNM | 37
INSTALLATION

15.2 Wiring diagram
DNM 3-6
1/N/PE ~ 200-240 V
L N
V
85_02_05_0002
15.3 Increasing the temperature
At 230V, the following water temperature increases result:
1,4 1,8 2,2 2,6 3,0 3,4
20,0
22,5
25,0
27,5
30,0
32,5
35,0
37,5
40,0
42,5
45,0
3
2
1
84_02_02_0056
X Flow rate in l/min
Y Temperature increase in K
1 3.5kW - 230 V
2 4.4kW - 230 V
3 5.7kW - 230 V

Flow rate l/min 2.0
Increasing the temperature K25
Cold water supply temperature °C 12
Maximum possible outlet temperature °C 37

INSTALLATION

38 | DNM www.stiebel-eltron.com
Note An outlet temperature of 50°C can be achieved with the
lowest possible flow rate and the following cold water
inlet temperatures:
- DNM 3 >18°C
- DNM 4 >21°C
- DNM 6 >22°C
15.4 Application areas
For the specific electrical resistance and specific electrical
conductivity, see "Data table".
Standard specifi-
cation

 
Spec.
Resist-
ance
ρ ≥
Spec. Conductiv-
ity σ≤
Spec.
Resist-
ance
ρ ≥
Spec. Conductiv-
ity σ≤
Spec.
Resist-
ance
ρ ≥
Spec. Conductiv-
ity σ≤
Ωcm mS/m μS/cm Ωcm mS/m μS/cm Ωcm mS/m μS/cm
1100 91 909 970 103 1031 895 112 1117
15.5 Details on energy consumption
The product data complies with EU regulations relating to the Directive on the ecodesign of energy related products (ErP).
DNM 3 DNM 4 DNM 6
185411 185415 185418
Manufacturer STIEBEL ELTRON STIEBEL ELTRON STIEBEL ELTRON
Load profile XXS XXS XXS
Energy efficiency class A A A
Annual power consumption kWh 477 478 478
Energy conversion efficiency %39 38 38
Sound power level dB(A) 15 15 15
Special information on measuring efficiency None None None

ENGLISH
www.stiebel-eltron.com DNM | 39
INSTALLATION

15.6 Data table
DNM 3 DNM 4 DNM 6
185411 185415 185418
Electrical data
Rated voltage V200 220 230 240 200 220 230 240 200 220 230 240
Rated output kW 2.7 3.2 3.5 3.8 3.3 4.0 4.4 4.8 4.3 5.2 5.7 6.2
Rated current A13.3 14.5 15.2 15.8 16.7 18.2 19.1 20 21.6 23.6 24.7 25.8
MCB/fuse rating A16 16 16 16 20 20 20 20 25 25 25 32
Frequency Hz 50/60 50/60 50/60 50/60 50/60 50/60 50/60 50/60 50/60 50/60 50/60 50/60
Phases 1/N/PE 1/N/PE 1/N/PE
Max. mains impedance at 50Hz Ω 0.434 0.394 0.377 0.361
Specific resistance ρ15 ≥ (at ϑcold ≤25°C) Ω cm 1100 1100 1100
Specific conductivity σ15 ≤ (at ϑcold ≤25 °C) 909 909 909
Connections
Water connection G 3/8 A G 3/8 A G 3/8 A
Application limits
Max. permissible pressure MPa 000
Values
Max. permissible inlet temperature °C 35 35 35
On l/min > 1.6 > 2.0 > 2.6
Pressure drop at flow rate MPa 0.05 0.06 0.08
Flow rate for pressure drop l/min 1.6 2.0 2.6
Flow rate limit at l/min 2.2 2.8 4.3
DHW line l/min 2.0 2.5 3.2
Δϑon delivery K25 25 25
Hydraulic data
Nominal capacity l 0.1 0.1 0.1

INSTALLATION

40 | DNM www.stiebel-eltron.com
DNM 3 DNM 4 DNM 6
Versions
Oversink installation X X X
Undersink installation X X X
Open vented type X X X
IP rating IP25 IP25 IP25
Protection class 1 1 1
Insulating block Plastic Plastic Plastic
Heating system heat generator Bare wire Bare wire Bare wire
Cover and back panel Plastic Plastic Plastic
Colour White White White
Dimensions
Height mm 143 143 143
Width mm 190 190 190
Depth mm 82 82 82
Weights
Weight kg 1.4 1.4 1.4

ENGLISH
www.stiebel-eltron.com DNM | 41
GUARANTEE | ENVIRONMENT AND RECYCLING
GUARANTEE

Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only grant
-
ed if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment.
After use,
dispose of the various materials in accordance with national
regulations.

Deutschland
STIEBEL ELTRON GmbH & Co. KG
Dr.-Stiebel-Straße 33 | 37603 Holzminden
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.de
Verkauf Tel. [phone] | Fax [phone] | [e-mail]
Kundendienst Tel. [phone] | Fax [phone] | [e-mail]
Ersatzteilverkauf Tel. [phone] | Fax [phone] | [e-mail]
Irr tum un d tec hni sch e Änd e ru n ge n v or b e ha l te n! | Sub jec t t o e r r or s and tec hni c al cha ng e s! | S ous rés e r v e d ‘e r reu r s
et de modifications techniques! | Onder voorbehoud van vergissingen en technische wijzigingen! | Salvo error o
m o d i f i c a c i ó n t é c n i c a ! | E x c e p t o e r r o o u a l t e r a ç ã o t é c n i c a | Z a s t r z e ż o n e z m i a n y t e c h n i c z n e i e w e n t u a l n e b ł ę d y | O m y l y a
technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések jogát fenntartjuk! | Отсутствиеошибокне
гарантируется. Возможны технические изменения. | Chyby a technické zmeny sú vyhradené! Stand 9147
Australia
STIEBEL ELTRON Australia Pty. Ltd.
6 Prohasky Street | Port Melbourne
VIC 3207
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel.com.au
Austria
STIEBEL ELTRON Ges.m.b.H.
Gewerbegebiet Neubau-Nord
Margaritenstraße 4 A | 4063 Hörsching
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.at
Belgium
STIEBEL ELTRON bvba/sprl
't Hofveld 6 - D1 | 1702 Groot-Bijgaarden
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.be
China
STIEBEL ELTRON (Guangzhou) Electric
Appliance Co., Ltd.
Rm 102, F1, Yingbin-Yihao Mansion, No. 1
Yingbin Road
Panyu District | 511431 Guangzhou
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltron.cn
Czech Republic
STIEBEL ELTRON spol. s r.o.
K Hájům 946 | 155 00 Praha 5 - Stodůlky
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.cz
Finland
STIEBEL ELTRON OY
Kapinakuja 1 | 04600 Mäntsälä
Tel. [phone]
[e-mail]
www.stiebel-eltron.fi
France
STIEBEL ELTRON SAS
7-9, rue des Selliers
B.P 85107 | 57073 Metz-Cédex 3
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.fr
Hungary
STIEBEL ELTRON Kft.
Gyár u. 2 | 2040 Budaörs
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.hu
Japan
NIHON STIEBEL Co. Ltd.
Kowa Kawasaki Nishiguchi Building 8F
66-2 Horikawa-Cho
Saiwai-Ku | 212-0013 Kawasaki
Tel. [phone] | Fax [phone]
[e-mail]
www.nihonstiebel.co.jp
Netherlands
STIEBEL ELTRON Nederland B.V.
Daviottenweg 36 |
5222 BH 's-Hertogenbosch
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.nl
Poland
STIEBEL ELTRON Polska Sp. z O.O.
ul. Działkowa 2 | 02-234 Warszawa
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.pl
Russia
STIEBEL ELTRON LLC RUSSIA
Urzhumskaya street 4,
building 2 | 129343 Moscow
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.ru
Slovakia
TATRAMAT - ohrievače vody s.r.o.
Hlavná 1 | 058 01 Poprad
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.sk
Switzerland
STIEBEL ELTRON AG
Industrie West
Gass 8 | 5242 Lupfig
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.ch
Thailand
STIEBEL ELTRON Asia Ltd.
469 Moo 2 Tambol Klong-Jik
Amphur Bangpa-In | 13160 Ayutthaya
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltronasia.com
United Kingdom and Ireland
STIEBEL ELTRON UK Ltd.
Unit 12 Stadium Court
Stadium Road | CH62 3RP Bromborough
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron.co.uk
United States of America
STIEBEL ELTRON, Inc.
17 West Street | 01088 West Hatfield MA
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebel-eltron-usa.com
A 272916-40002-9244
4<AMHCMN=hcjbgi>