STIEBEL ELTRON SN 5 SL User manual

275989
» SN 5 SL | SN 5 SLi comfort
» SN 10 SL | SN 10 SLi comfort
» SN 15 SL | SN 15 SLi comfort



GEBRAUCHS- UND MONTAGEANLEITUNG
OPERATING AND INSTALLATION INSTRUCTIONS
NOTICE D’UTILISATION ET DE MONTAGE
GEBRUIKS- EN MONTAGEAANWIJZING
,16758.&-$2%68*,,0217$¾81d92'.328½,7$.0217d½,.(=(/v6,v66=(5(/v6,87$67d6ɂɇɋɌɊɍɄɐɂəɉɈɆɈɇɌȺɀɍɂɗɄɋɉɅɍȺɌȺɐɂɂOFFENER (DRUCKLOSER) WARMWASSERSPEICHER | OPEN (PRESSURELESS) WATER HEATER |
CHAUFFE-EAU OUVERT (A ÉCOULEMENT LIBRE) | OPEN (DRUKLOZE) WARMWATERBOILER |
32-(012¤&,2:(%(=&,¤1,(1,2:(2*5=(:$&=(:2'<|%(=7/$.29¹=d62%1.29¹2+¢9$o7(3/v92'<|1<,72771<20d61v/.²/,0(/(*9=7d52/|ptlr}t}kcgiobqpro}koblpqjtgm~o}kdpfpobergdbtgm~

2
Deutsch Seite 6-7
Inhaltsverzeichnis
English page 8-10
List of contents
Français page 11-13
Sommaire
Nederlands bladzijde 14-16
Inhoudsopgave
Polski strona 20-22
Spis treści
Česky strana 24-26
Obsah
Magyar oldal 28-30
Tartalomjegyzék
rÂÚÚµÒÓsÛÙËÖÒÞËè&RÎÏÙÐËÖÒÏ1. Gebrauchsanleitung _________________________4
1.1 Gerätebeschreibung_____________________ 4
1.2 Das Wichtigste in Kürze ________________ 4
1.3 Bedienung ________________________________ 4
1.4 Wichtige Hinweise _______________________ 4
1.5 Pflege und Wartung _____________________ 4
1.6 Was tun wenn . . . ? _____________________ 4
1.7 Sonderzubehör ___________________________ 4
2. Montageanleitung ___________________________5
2.1 Geräteaufbau ____________________________ 5
2.2 Gerätebeschreibung_____________________ 5
2.3 Technische Daten ________________________ 5
2.4 Vorschriften und Bestimmungen _____ 5
2.5 Wichtiger Hinweis _______________________ 5
2.6 Montageort _______________________________ 5
2.7 Gerätemontage___________________________ 5
2.8 Erstinbetriebnahme _____________________ 5
2.9 Servicehinweise __________________________ 5
3. Störungsbeseitigung ________________________6
4. Umwelt und Recycling_______________________6
5. Kundendienst und Garantie ________________7
1. Operating Instructions ______________________8
1.1 Description of Unit_______________________ 8
1.2 The most important points in brief ___ 8
1.3 Operation __________________________________ 8
1.4 Important Note ___________________________ 8
1.5 Care and Maintenance __________________ 8
1.6 What to do if....___________________________ 8
1.7 Special accessories ______________________ 8
2. Installation Instructions _____________________9
2.1 Unit Type __________________________________ 9
2.2 Description of Unit_______________________ 9
2.3 Technical Data ____________________________ 9
2.4 Regulations and Conditions____________ 9
2.5 Important Notes__________________________ 9
2.6 Installation Site __________________________ 9
2.7 Unit Installation __________________________ 9
2.8 First Use ___________________________________ 9
2.9 Service Notes _____________________________ 9
3. Fault Repair ________________________________ 10
4. Environment and recycling ________________ 10
5. Guarantee___________________________________ 10
1. Instructions d’utilisation à l‘usage _______ 11
1.1 Description de l’appareil ______________ 11
1.2 Sommaire des informations essenti-
elles _______________________________________ 11
1.3 Utilisation ________________________________ 11
1.4 Observations importantes _____________ 11
1.5 Entretien et maintenance _____________ 11
1.6 Que faire si … ?__________________________ 11
1.7 Accessoires spécifiques ________________ 11
2. Instructions de montage __________________ 12
2.1 Composants de l’appareil ____________ 12
2.2 Description de l’appareil ______________ 12
2.3 Caractéristiques techniques __________ 12
2.4 Normes et réglementations __________ 12
2.5 Remarque importante _________________ 12
2.6 Lieu de montage _______________________ 12
2.7 Montage de l’appareil _________________ 12
2.8 Première mise en service______________ 12
2.9 Instructions de maintenance ___________ 12
3. Dépannage _________________________________ 13
4. Environment et recyclage__________________ 13
5. Garantie_____________________________________ 13
1. Gebruiksaanwijzing _______________________ 14
1.1 Beschrijving van het toestel___________ 14
1.2 In kort bestek ____________________________ 14
1.3 Bediening ________________________________ 14
1.4 Belangrijke instructies _________________ 14
1.5 Reiniging en onderhoud ______________ 14
1.6 Wat te doen, indien . . . ? _____________ 14
1.7 Speciale accessoires ____________________ 14
2. Montageaanwijzing _______________________ 15
2.1 Opbouw van het toestel _______________ 15
2.2 Beschrijving van het toestel___________ 15
2.3 Technische gegevens ___________________ 15
2.4 Voorschriften en bepalingen__________ 15
2.5 Belangrijke instructies _________________ 15
2.6 Plaats van montage ____________________ 15
2.7 Montage van het toestel _______________ 15
2.8 Eerste inbedrijfsname__________________ 15
2.9 Service-instructies ______________________ 15
3. Verhelpen van storingen __________________ 16
4. Millieu en recycling ________________________ 16
5. Garantie_____________________________________ 16
1. Instrukcja obsługi _________________________ 20
1.1 Opis urządzenia _________________________ 20
1.2 Ważne wskazówki w skrócie__________ 20
1.3 Obsługa ___________________________________ 20
1.4 Ważna wskazówka ______________________ 20
1.5 Konserwacja i czyszczenie_____________ 20
1.6 Co robić, gdy ...? ________________________ 20
1.7 Osprzęt dodatkowy _____________________ 20
2. Instrukcja montażu ________________________ 21
2.1 Budowa urządzenia ___________________ 21
2.2 Opis urządzenia _________________________ 21
2.3 Dane techniczne_________________________ 21
2.4 Przepisy i zalecenia _____________________ 21
2.5 Ważne wskazówki_______________________ 21
2.6 Miejsce montażu urządzenia _________ 21
2.7 Montaż urządzenia _____________________ 21
2.8 Pierwsze uruchomienie________________ 21
2.9 Wskazówki serwisowe _________________ 21
3. Usuwanie usterek _________________________ 22
4. Środowisko naturalne i recykling_________ 22
5. Gwarancja __________________________________ 22
1. Návod k použití ____________________________ 24
1.1 Popis přístroje ___________________________ 24
1.2 Nejdůležitější informace ve zkratce__ 24
1.3 Obsluha ___________________________________ 24
1.4 Důležité pokyny__________________________ 24
1.5 Ošetřování a údržba ____________________ 24
1.6 Co dělat, když . . .? _____________________ 24
1.7 Zvláštní příslušenství ___________________ 24
2. Instrukce k montáži ________________________ 25
2.1 Konstrukce přístroje ____________________ 25
2.2 Popis přístroje ___________________________ 25
2.3 Technická data___________________________ 25
2.4 Předpisy a ustanovení__________________ 25
2.5 Důležité pokyny__________________________ 25
2.6 Montážní místo _________________________ 25
2.7 Montáž přístroje_________________________ 25
2.8 První uvedení do provozu _____________ 25
2.9 Pokyny pro servis________________________ 25
3. Odstraňování závad _______________________ 26
4. Ekologie a recyklace _______________________ 26
5. Záruční podmínky__________________________ 26
1. Kezelési utasítás ___________________________ 28
1.1 A készülék leírása _______________________ 28
1.2 A legfontosabbak röviden _____________ 28
1.3 Kezelés ____________________________________ 28
1.4 Fontos figyelmeztetések _______________ 28
1.5 Tisztítás és karbantartás _______________ 28
1.6 Mit tegyenek, ha… ______________________ 28
2. Szerelési utasítás __________________________ 29
2.1 A készülék felépítése __________________ 29
2.2 A készülék leírása_______________________ 29
2.3 Műszaki adatok__________________________ 29
2.4 Előírások és meghatározások_________ 29
2.5 Fontos figyelmeztetések _______________ 29
2.6 A felszerelés helye _____________________ 29
2.7 A készülék felszerelés _________________ 29
2.8 Első üzembe helyezés__________________ 29
2.9 Szervízelőírások _________________________ 29
3. Hibaelhárítás _______________________________ 30
4. Környezet és újrahasznosítás______________ 30
5. Garancia_____________________________________ 30
1. ɂɧɫɬɪɭɤɰɢɹɩɨɷɤɫɩɥɭɚɬɚɰɢɢ_____ 31
ɈɩɢɫɚɧɢɟɩɪɢɛɨɪɚBBBBBBBBBBB31
ɄɨɪɨɬɤɨɨɫɚɦɨɦɜɚɠɧɨɦBBBBBB31
ɍɩɪɚɜɥɟɧɢɟBBBBBBBBBBBBBBBBB31
ȼɚɠɧɵɟɭɤɚɡɚɧɢɹBBBBBBBBBBBB31
ɍɯɨɞɢɬɟɯɧɢɱɟɫɤɨɟɨɛɫɥɭɠɢɜɚɧɢɟBBBBBBBBBBBBBBB31
ɑɬɨɞɟɥɚɬɶɟɫɥɢ«"BBBBBBBBBB31
ɋɩɟɰɢɚɥɶɧɵɟɩɪɢɧɚɞɥɟɠɧɨɫɬɢB31
ɂɧɫɬɪɭɤɰɢɹɩɨɦɨɧɬɚɠɭ_________ 32
ɄɨɧɫɬɪɭɤɰɢɹɩɪɢɛɨɪɚBBBBBBBBB32
ɈɩɢɫɚɧɢɟɩɪɢɛɨɪɚBBBBBBBBBBB32
ɌɟɯɧɢɱɟɫɤɢɟɯɚɪɚɤɬɟɪɢɫɬɢɤɢBBB32
ɉɪɟɞɩɢɫɚɧɢɹɢɨɩɪɟɞɟɥɟɧɢɹBBB32
ȼɚɠɧɵɟɭɤɚɡɚɧɢɹBBBBBBBBBBBB32
ɆɟɫɬɨɦɨɧɬɚɠɚBBBBBBBBBBBBBB32
ɆɨɧɬɚɠɩɪɢɛɨɪɚBBBBBBBBBBBBB32
ɉɟɪɜɵɣɜɜɨɞɜɷɫɤɩɥɭɚɬɚɰɢɸBBB32
ɍɤɚɡɚɧɢɹɩɨɫɟɪɜɢɫɧɨɦɭɨɛɫɥɭɠɢɜɚɧɢɸBBBBBBBBBBBBBBB32
ɍɫɬɪɚɧɟɧɢɟɧɟɢɫɩɪɚɜɧɨɫɬɟɣ_____ 33
Ɉɤɪɭɠɚɸɳɚɹɫɪɟɞɚɢɜɬɨɪɫɵɪɶɺ_ 33
Ƚɚɪɚɧɬɢɹ_______________________ 33

3








3
4
C26_02_06_0045
2
1
5
6
7
8
C
A
F
B
G
E
D
26_02_06_0052
26_02_01_0067
26_02_06_0049 26_02_06_0048
26_02_06_0050




















26_02_01_0389
Typ SN 5 SL
SN 5 SLi
SN 10 SL
SN 10 SLi
SN 15 SL
SN 15 SLi
a230 mm 275 mm 295 mm
b263 mm 295 mm 316 mm
d140 mm 200 mm 200 mm
e303 mm 387 mm 495 mm
h421 mm 503 mm 601 mm
i118 mm 116 mm 106 mm
dSN 10 SL | SN 10 SLi
SN 15 SL | SN 15 SLi
2 kW
C26_02_01_0070
SN 5 SL | SN 5 SLi: 200 mm
C26_02_06_0051
SN 15 SL | SN 15 SLi: 170 mm
SN 15 SL | SN 15 SLi: 320 mm
3,3 kW
C26_02_01_0069
SN 10 SL | SN 10 SLi: 130 mm
SN 15 SL | SN 15 SLi: 170 mm
SN 10 SL | SN 10 SLi: 260 mm
SN 15 SL | SN 15 SLi: 320 mm
2 kW
a
b
c
2 kW 3,3 kW

8
1. Operating Instructions for the user and engineer
1.1 Description of Unit
The open (pressure-less) water heater con-
stantly maintains the water content at the
preset temperature.
On heating, the expansion water drips through
the outlet fitting.
Only fittings for open (pressureless) water
heaters may be installed.
We recommend Stiebel Eltron fittings: for or-
der no. see 1.7 "Special accessories".
1.2 The most important points
in brief
• Set the desired hot water temperature
at the temperature selector (1)
• The unit is heating when the display (2)
lights.





1
C26_02_06_0053
2
1.3 Operation
Temperature setting
°C = cold. On this setting, the unit, but not
the fitting or water pipe, is protected
from frost
Eco = recommended energy-saving setting
(approx. 60 °C), low limescale forma-
tion
85 = max. temperature setting.
Note:
On request, the engineer can restrict the tem-
perature on the unit (see 2.8 “First Use”) so
that the temperature can be set anywhere up
to the temperature limit.
Heating time:
If the entire water content is used, the heating
time is that shown on the diagram.
35 °C 55 °C E 65 °C 85 °C
[min]
SN 15SL | SLi
2 kW
SN 10SL | SLi
2 kW
SN 15SL | SLi
3,3 kW
SN 5 SL | SLi
2 kW
40
35
30
25
20
15
10
5
0
Example SN 5 SL | SN 5 SLi:
Temperature setting: 65 °C
Heating time: approx. 9.5 minutes
Mixed water quantity:
Using the temperature, you set a mixed water
quantity for e.g. 40 °C.
[ l ]
SN 15 SL | SLi
SN 10 SL | SLi
SN 5 SL | SLi
45
40
35
30
25
20
15
10
5
0
40 °C 55 °C E 65 °C 85 °C
Example SN 5 SL | SN 5 SLi:
Temperature setting: 65 °C
Cold water feed: 15 °C
Mixed water quantity: approx. 10 l
1.4 Important Note
•The water heater must not be pres-
surized. Never block the fitting outlet
and do not use a Perlator or hose with jet
controller.
•If the temperature is set higher than 45 °C,
very hot water can flow immediately!
• If it is intended that children or people
with restricted physical, sensory or mental
capabilities are to operate the appliance,
they must only be permitted to do so after
appropriate instruction has been provided by
the person responsible for their safety.
Children should be supervised to ensure that
they do not play with the device.
Risk of scalding!
•We recommend the use of the temperature
restrictor set by the engineer, unless abso-
lutely necessary otherwise.
• 2 kW versions: to avoid danger from ac-
cidental resetting of the protective tempera-
ture restrictor in the case of a fault, the unit
must not be connected via a timer switch.
Limescale can block the outlet and hence pres-
surize the heater.
Signs of limescale are boiling sounds and
reduced water flow. In this case have the unit
and fitting descaled by an engineer
On use of a shower fitting (see 1.7 Special Ac-
cessories), regular descaling is necessary (re-
moval of limescale from the spray head).
The thermostat knob may only be removed by
an engineer.
All information in these Operating and Instal-
lation Instructions must be observed. The
instructions contain important information for
safety, operation and maintenance of the unit.
1.5 Care and Maintenance
To clean the unit, simply wipe with a damp
cloth. Do not use abrasive or aggressive clean-
ing agents.
Maintenance work should only be
performed by an engineer.
1.6 What to do if....
...there is no hot water:
Check the thermostat, plug and fuse.
...there is a boiling sound from the unit:
Have the unit and fitting descaled by an en-
gineer.
...see also 3. „Fault repair by the user and
engineer”.
If an engineer is called for a problem, to help
him resolve this more quickly and efficiently,
please give him the information below on the
unit rating plate (8):

..............
C26_02_06_0054
1.7 Special accessories
Stiebel Eltron order numbers:
• Two-handle tempering fittings
- sink fitting:
WKM 22 24 34
- shower fitting:
WDM 22 24 35
• Single lever mixer fittings
- sink fitting:
MEK 22 24 43
- shower fitting:
MED 22 24 44

9
2. Installation Instructions for the engineer
Installation and electrical connection may
only be carried out by an engineer in accord-
ance with these instructions.
2.1 Unit Type A
1Temperature selection knob
2Indicator light
3Cold water connection (blue)
4Hot water connection (red)
5Electrical connection line
6Suspension rail
7Electric heating flange
8Rating plate
2.2 Description of Unit
Open (pressureless) water heater for oversink
installation, to supply a water tap, for heating
cold water to EN 806.
Only fittings for open (pressureless) water
heaters may be installed.
We recommend Stiebel Eltron fittings: for or-
der no. see 1.7 "Special accessories".
2.3 Technical Data
Current data on the rating plate.
Type SN 5SL
SN5SLi SN10SL SN10SLi SN15SL SN15SLi SN 15 SL SN15SLi
Nominal ca-
pacity
5 l 10 l 15 l 15 l
Design open
Weight 3,0 kg 4,6 kg 5,8 kg 6,1 kg
Heating
power
2,0 kW 2,0 kW 2,0 kW 3,3 kW
Voltage 230 V
Flow rate,
max.
5
l/min
10
l/min
12
l/min
Protection to
EN 60529
IP 24 D
Connection
line with
plug
ca. 650 mm
Temperature
setting range
ca. 35 °C - 85 °C
(fully adjustable)
Table 1
2.4 Regulations and Conditions
• Perfect function and operating safety can
only be guaranteed with the original
Stiebel Eltron accessories and spare parts
designed for the unit.
• The fitting outlet serves for ventilation. Do
not block the outlet connector or fitting
swivel arm. Do not use a perlator or hose
with jet regulator.
•Electrical connection
- Plug connection:
An earthed socket is required. This must
be freely accessible after the device has
been installed. If country-specific plugs
and sockets are used, they must be fitted
with an earthing contact and must con-
form to the individual national standards.
- Fixed connection:
If the appliance is instended to be con-
nected to the AC mains (appliance con-
nection socket), it must be capable of
all-pole disconnection from the mains by
means of a circuit sever of at least 3 mm.
SN 5 SL | SN 5 SLi and SN 10 SL | SN 10 SLi:
Installation with a direct (fixed) electrical
cable is not permitted.
SN 15 SL and SN 15 SLi:
Installation with a fixed connection cable
is only permitted in conjunction with the
installation kit "Permanent electrical con-
nection" (Stiebel Eltron order no. 22 32 19).
Only with this installation kit is protection
class IP 24 D retained.
• The conditions of the local electricity sup-
ply company and competent water supply
authority must be observed.
2.5 Important Notes
If this unit is exposed to water pres-
sure, the container may leak and
cause water damage.
2.6 Installation Site B
The heater should be installed in a frost-free
room, vertically with water connections at the
bottom.
The maximum permitted length of connecting
pipe from fitting to unit is 1 m. If this is ex-
ceeded, an additional pipe ventilator must be
installed in the overflow line.
2.7 Unit Installation
• Mount the suspension rail, position using
mounting template (5 l unit pages 18-19;
10 and 15 l in pack). Select fixing materials
according to the strength of the wall.
Excess line length can be stored in the cable
holder Cprovided.
• Suspend the unit.
• Fit the water connections C, set the flow
rate (see 2.3 Technical Data and Description
of Unit).
Note on two-handle mixer set:
The control handles for the two-handle mi-
xer set are supplied to DIN 44897:
cold water left (blue)
hot water right (red).
2.8 First Use
(By the engineer only!)
I. Open the hot water fitting or set the one-
hand mixer to “warm” until the water
emerges free from bubbles.
II. Connect the electrical plug and select the
temperature.
Danger of running dry!
If the sequence is changed, the pro-
tective temperature restrictor will trip in.
2 kW: ... in this case, add water and isolate
the unit from the power supply briefly.
3,3 kW: ... in this case, replace the thermo-
stat and temperature limiter.
III. Temperature setting restrictor F:
Only if the restricted temperature setting
is required is the max. temperature set
via the restrictor ring.
IV. Remove protective film from controls.
Unit hand-over:
Explain to the user how the unit works and
how to operate it. Point out any possible dan-
gers (scalding). Give him these Installation
and Operating Instructions for safe keeping.
2.9 Service Notes
Before all work, first isolate the unit
from the power supply and remove
the unit from the wall.
• Open unit G:
aPull off thermostat and temperature re-
strictor ring. Remove screw.
bLower locking bolt
c Swivel housing cover aside and remove.
dFor SN 10 SL | SN 10 SLi and SN 15 SL |
SN 15 SLi only:
open clamp band (protection against tilt-
ing).
• Replace electrical power line:
To replace the connecting line use Stiebel
Eltron.
2 kW: Order no. 02 06 71, or with an
H05VV-F3x1.0 line
3.3 kW: Order no. 02 39 71, or with an
H05VV-F3x1.5 line.
Circuit diagram D
• Positioning of thermostat / temperature
restrictor sensor in protective pipe:
When replacing or removing the thermostat /
restrictor, insert the sensor in the protective
pipe according to E; on SN 5 SL and SN 5 SLi,
also attach the temperature sensor below the
earth plug.
• Drain unit:
The unit is drained via the connector.
• Descaling:
Remove heating flange, remove coarse scale
by careful tapping, immerse heating element
in limescale remover up to the flange plate.
• Checking earth conductor to BGV A3:
Disconnect the plug and remove the thermo-
stat. Test at the thermostat fixing screw and
earth contact of the connection line.
English

10
5. Guarantee
For guarantees please refer to the pespective
terms and conditions of supply for your coun-
try.
4. Environment and recycling
The installation, electrical connection
and first operation of this appliance
should be carried out by a qualified installer.
The company does not accept liability for
failure of any goods supplied which accor-
dance with the manufacturer‘s instructions.
$$$ "'+(('  !)'("#('$#'#+(("& &)'-!)'(# ('$&( -"'$#'##&"(# # &) (#"'
3. Fault Repair for the user and engineer
Fault Cause Rectification
No hot water despite hot water fit-
ting being fully open.
No power. User / Engineer: Check fuses on domestic system.
Limescale on jet regulator. User / Engineer: Clean or replace jet regulator on fitting.
Protective temperature restrictor
(STB) has tripped.
Engineer: Eliminate cause of fault (replace thermostat).
Note on protective temperature restrictor (STB) / re-
strictor:
2 kW unit: STB resets automatically when the unit
power supply is disconnected
3.3 kW unit: Replace restrictor.
Boiling sound in heater. Limescale in heater. Engineer: Descale unit.
Table 2