Stratasys F123 Series Operating instructions

Part No. 401692-0001_REV_H
F123 Series Shared Office
3D Printing System
Site Preparation Guide

Site Preparation Guide
Page ii
Copyright
Copyright © 2017 - 2022 Stratasys Ltd. All rights reserved.
This documentation contains proprietary information of Stratasys Ltd. This information is supplied solely to
assist authorized users of this Stratasys 3D printing system. No part of this document may be used for other
purposes, and it may not be disclosed to other parties. The specifications on which this document is based
are subject to change without notice. No part of this book may be reproduced in any form or by any means,
nor stored in a database or retrieval system, without prior permission in writing from Stratasys Ltd.
If this document is distributed as a PDF file, you may print it for internal use.
Part No. 401692-0001_REV_H
Liability
Stratasys shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material. Stratasys makes no warranty of any kind
with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. It is the responsibility of the system owner/material buyer to determine that Stratasys
material is safe, lawful, and technically suitable for the intended application as well as identify the proper
disposal (or recycling) method consistent with local environmental regulations. Except as provided in
Stratasys' standard conditions of sale, Stratasys shall not be responsible for any loss resulting from any use of
its products described herein.
Trademarks
Stratasys, F123 Series, F170, F190 CR, F270, F370, F370 CR, GrabCAD, Insight, FDM, and all printer
materials are trademarks of Stratasys Ltd. and/or its subsidiaries or affiliates and may be registered in certain
jurisdictions. All other product names and trademarks are the property of their respective owners.

Page iii
Stratasys Confidential
Contents
Revision Log ................................................................................................. iv
Safety............................................................................................................ iv
Safe Environment................................................................................................................ iv
Introduction .................................................................................................... 1
How to Use This Guide........................................................................................................ 1
About the F123 Series Printers ........................................................................................... 1
System Components ........................................................................................................... 2
Site Requirements ......................................................................................... 4
Physical Specifications and Space Requirements .............................................................. 4
Environmental Requirements .............................................................................................. 7
AC Power Requirements..................................................................................................... 9
Workstation Requirements .................................................................................................. 9
LAN Requirements .............................................................................................................. 9
Preparing for Installation.............................................................................. 10
Inspect Crate for Damage ................................................................................................. 10
Required Tools and Equipment ......................................................................................... 10
Unpacking the Printer........................................................................................................ 10
Site Preparation Checklist ........................................................................... 17
Electrical Installation Requirements .................................................................................. 17
Environmental Requirements ............................................................................................ 17
Required Installation Tasks................................................................................................ 17

Site Preparation Guide Revision Log
Page iv
Revision Log
The following table lists the changes in each revision of this document.
Safety
The following basic safety tips are given to ensure safe installation, operation, and
maintenance of Stratasys equipment and are not to be considered as comprehensive on
matters of safety. Although the F123 Series printers are designed to be safe and reliable,
access to areas of the printer are potentially dangerous.
Safe Environment
• Connect equipment to a grounded facility power source. Do not defeat or bypass the
ground lead.
• Know the location of equipment branch circuit interrupters or circuit breakers and how to
turn them on and off in case of emergency.
• Know the location of fire extinguishers and how to use them. Use only ABC type
extinguishers on electrical fires.
• Know local procedures for first aid and emergency assistance at the customer facility.
• Use adequate lighting at the equipment.
• Maintain the recommended range of temperature and humidity in equipment area.
• Do not use this product in an environment containing volatile or flammable compounds.
Translations of this guide are updated periodically. If you are consuming a translated version, please
check the English version for the latest revision and list of updates.
Revision Date Description of Changes
A January 2017 First release of this document.
B February 2017 Updated USB ports and material storage spec.
C December 2017 Added heat output, updated material storage °C
temperature and deleted checklist item
D November 2018 Added TPU 92A (Elastomer) information
E November 2019 Added Diran and ESD7 information
F March 2020 Added 240V note
G March 2021 Added ABS-CF10 information
H May 2022 Added F190 CR and F370 CR

Site Preparation Guide Introduction
Page 1
Introduction
How to Use This Guide
This guide provides information for selecting an appropriate location for the F123 Series
printer. This guide also provides instructions for unpacking and preliminary set-up. Information
of particular importance is presented in one of three formats:
About the F123 Series Printers
The Stratasys F123 Series 3D printers incorporate the latest in innovative technology to
provide you with precise prototypes from a CAD design. Stratasys’ Fused Deposition Modeling
(FDM) technology provides prototype parts, including internal features, which can be used to
field-test form, fit, and function. Direct Digital Manufacturing (DDM) allows for the creation of
customized end-use parts straight from 3D CAD data. The F123 Series printers feature a
servo/belt driven XY gantry with multiple modeling material capability.
A Warning: indicates a procedure that may cause injury to an operator if the
procedure is not followed.
A Warning: will precede the paragraph of instruction to which it relates.
A Caution: indicates a procedure that may cause damage to equipment if the
procedure is not followed.
A Caution: will precede the paragraph of instruction to which it relates.
A NOTE is used to highlight a specific point or to provide an operational tip. While
useful, a NOTE does not indicate a procedure that can cause injury or damage if it is
not followed.
A NOTE will follow the paragraph of instruction to which it relates.

Site Preparation Guide Introduction
Page 2
System Components
• The F123 Series Printer
• Material Package(s)
• Welcome Kit (containing documentation on how to download your user guide and common
tools for maintaining the printer)
• GrabCAD Print Software Package
• A Computer Workstation (not sold by Stratasys)
F170 Highlights
• Maximum build area of 10 x 10 x 10 inch (254 x 254 x 254 mm)
• Material Bays: 1 model, 1 support
• Touchscreen Graphical User Interface
• Wi-Fi capabilities
• Three USB ports (2 in front, 1 in back)
• Camera for remote monitoring
F190 CR Highlights
• Maximum build area of 12 x 10 x 12 inch (308 x 254 x 308 mm)
• Material Bays: 1 model, 1 support
• Touchscreen Graphical User Interface
• Auto changeover capabilities
• Wi-Fi capabilities
• Three USB ports (2 in front, 1 in back)
• Camera for remote monitoring
F270 Highlights
• Maximum build area of 12 x 10 x 12 inch (308 x 254 x 308 mm)
• Material Bays: 2 model, 2 support
• Touchscreen Graphical User Interface
• Auto changeover capabilities
• Wi-Fi capabilities
• Three USB ports (2 in front, 1 in back)
• Camera for remote monitoring

Site Preparation Guide Introduction
Page 3
F370/F370 CR Highlights
• Maximum build area of 14 x 10 x 14 inch (356 x 254 x 356 mm)
• Material Bays: 2 model, 2 support
• Insight Software Package
• Touchscreen Graphical User Interface
• Auto changeover capabilities
• Wi-Fi capabilities
• Three USB ports (2 in front, 1 in back)
• Camera for remote monitoring

Site Preparation Guide Site Requirements
Page 4
Site Requirements
Decide where to install the printer based on the following:
1. Space Requirements
2. Environmental Requirements
3. Electrical Requirements
4. LAN Requirements
Physical Specifications and Space Requirements
Dimensions and Weights
Make sure that the installation site floor space can accommodate the printer’s weight and
dimensions, plus required clearances.
The F123 Series printers are capable of generating vibrations depending mainly
on part build geometry and material characteristics. This consideration will need
to be taken into account if locating the printer near vibration sensitive equipment.
Status Dimensions/Weights
Crated
Width: 48 inches (122 cm)
Depth: 40 inches (102 cm)
Height: 76 inches (193 cm)
Uncrated
Width: 34 inches (86 cm)
Depth: 28 inches (71 cm)
Height: 64 inches (163 cm)
Shipping Weight (crated) 706 pounds (320 kg)
Printer Weight (uncrated) 500 pounds (227 kg)

Site Preparation Guide Site Requirements
Page 5
Figure 1: F123 Center of Mass
All dimensions are in inches and are taken from the center of the front left leveling
foot.

Site Preparation Guide Site Requirements
Page 6
Minimum Operational Clearances
Sufficient rear and side clearances allow for proper air circulation, while sufficient front
clearance allows enough room for the oven door and drawers to be opened.
Figure 2: Minimum Clearances
Side Clearance Minimum 4 inches (10.16 cm) on each side
Rear Clearance Minimum 6 inches (15.24 cm)
Front Clearance Minimum 20 inches (50.8 cm)
Overhead Clearance Minimum 20 inches (50.8 cm)
20 inches (50.8 cm) minimum for overhead clearance
20 inches
(50.8 cm)
FrontRear
6 inches
(15.24 cm)
4 inches
(10.16 cm)
4 inches
(10.16 cm)

Site Preparation Guide Site Requirements
Page 7
Environmental Requirements
• The F123 Series printer is for indoor use only.
• Air quality conditions with excessive solid particulates (conductive or non-conductive) may
result in system damage.
• Air quality conditions in which airborne oils are allowed to accumulate on or within the
printer can damage the plastic components.
• System operating temperature shall be in the range of 59°F to 86°F (15°C to 30°C), with
relative humidity range of 30% to 70% non-condensing.
• System storage temperature shall be in the range of 32°F to 95°F (0°C to 35°C), with
relative humidity range of 20% to 90% non-condensing.
• Altitude shall not exceed 6561.68 feet (2000 m).
• Material storage shall be in the range of 55°F to 86°F (13°C to 30°C), with relative humidity
less than 70%.
• Noise emission (acoustic): <32dBA when idle, <46dBA when building
Heat Output
Heat dissipation occurs mostly through the top of the printer. Heat output is material dependent
due to the various temperatures maintained in the build chamber.
Material Type Heat Output (while building) Heat Output (while idle)
ABS ~2300 BTU/hr ~1800 BTU/hr
ABS ESD7 ~2300 BTU/hr ~1800 BTU/hr
ABS-CF10 ~2600 BTU/hr ~2200 BTU/hr
PC-ABS ~2600 BTU/hr ~2100 BTU/hr
PLA ~550 BTU/hr ~35 BTU/hr
ASA ~2300 BTU/hr ~1800 BTU/hr
TPU 92A ~2300 BTU/hr ~1800 BTU/hr
DiranTM 410MF07 ~2950 BTU/hr ~2900 BTU/hr
Nylon-CF10 ~2600 BTU/hr ~2200 BTU/hr

Site Preparation Guide Site Requirements
Page 8
Power Consumption
Power consumption is material dependent due to the various temperatures maintained in the
build chamber.
Material Type Power Consumption
(while building)
Power Consumption
(while idle)
Power Consumption
(while sleeping)
ABS 650 W 510 W 10 W
ABS ESD7 650 W 510 W 10 W
ABS-CF10 750 W 650 W 10 W
PC-ABS 750 W 610 W 10 W
PLA 150 W 10 W 10 W
ASA 650 W 510 W 10 W
TPU 92A 650 W 510 W 10 W
Diran 410MF07 850 W 825 W 10 W
Nylon-CF10 750 W 650 W 10 W

Site Preparation Guide Site Requirements
Page 9
AC Power Requirements
• 50/60 Hz.
• Voltage: 100-132, 200-240 VAC.
• Maximum input voltage variation: ±10% of nominal
• Current: 15/7A.
• The grounded electrical outlet must connect to either a Euro or a US power cord plug
(provided in the Welcome Kit) and must be located within 6 feet (1.83m) of the printer.
Operation of the printer outside this range is not recommended; degradation of performance
and shortened component life expectancy will be experienced. Facilities who are unsure of
their power quality should contact their service provider.
Workstation Requirements
For GrabCAD Print workstation requirements please visit:
http://help.grabcad.com/article/195-system-requirements-for-grabcad-print.
For Insight workstation requirements please visit the Stratasys website.
LAN Requirements
If utilizing a LAN connection for communication and file transfer functions, the LAN connection
is a 100 base T, Ethernet protocol, RJ45 connector. One 15 foot (4.57 m) CAT6, 10/100 base T
cable is supplied with the printer, located in the Welcome Kit. The printer will function in either
DHCP or Static IP configurations.
A LAN connection is not required however, as the printer is also capable of file transfer via a
Wi-Fi connection or a USB flash drive plugged into either of the printer’s USB ports. See the
F123 Series User Guide for detailed information and instructions on transferring files to the
printer.
Caution:
A power cable is provided for connecting the printer to the AC electric source. Do not
use it with other equipment.
Caution:
Do not use an extension cord or power strip; doing so can result in intermittent power
issues. Connect the power cord directly into the receptacle or UPS.

Site Preparation Guide Preparing for Installation
Page 10
Preparing for Installation
Inspect Crate for Damage
Before opening the shipping crate, inspect the crate for signs of exterior damage. Report
evidence of excessive damage to Stratasys and the shipping company.
Required Tools and Equipment
• Basic hand tools (powered screwdriver or drill with Phillips bit).
• Utility knife.
• A pallet jack or forklift may be required to move the system.
Unpacking the Printer
Figure 3: Ramp Clearance
If you intend to remove the printer from its shipping base via the ramp, make sure that
there is at least 81 inches (206 cm) of clearance for the ramp and the printer before
you begin the process of unpacking the printer (Figure 3). The printer’s shipping base
indicates the location of the ramp.
81 Inches
(206 cm)

Site Preparation Guide Preparing for Installation
Page 11
Remove Shipping Materials
1. Inspect the Tilt Indicators (2) and ShockWatch indicator affixed to the exterior of the
cardboard box. If possible, take a picture of these indicators to share with your installation
representative. If damage is detected upon installation, this photo will assist your
installation representative in determining the cause of damage (Figure 4).
2. Using a Phillips screwdriver, remove the cover mount screws from the base of the crate
(Figure 4).
Figure 4: Shipping Crate Detail
3. Carefully cut the shipping bands (Figure 4).
4. Remove the cardboard cover from the top of the crate (Figure 5).
5. Remove the 2 protective cardboard container panels encasing the printer (Figure 5).
Shipping
Bands (6)
Cover Mount
Screws
Tilt
Indicator
ShockWatch Indicator
(1 as shown)
(2 as shown)
Rear View Front View
Warning: Personal Injury Hazard
Shipping bands are very tight; when cutting shipping bands they may pop open with
force. Wear safety glasses when removing the shipping bands.

Site Preparation Guide Preparing for Installation
Page 12
6. Remove the foam restraining insert from the top of the printer (Figure 5).
Figure 5: Unpacking the Printer (cover removed)
7. Remove the printer from the shipping base, this can be done using a fork lift (see “Remove
Printer from Shipping Base - Fork Lift Instructions” (page 13)) or manually via the use of a
ramp (see “Remove Printer from Shipping Base - Ramp Instructions” (page 14)).
Protective
Cardboard
Container
Panels (x2)
Cover
Foam Insert

Site Preparation Guide Preparing for Installation
Page 13
Remove Printer from Shipping Base - Fork Lift Instructions
1. Unlatch the two link locks securing the ramp in a vertical position (Figure 7). Remove the
foam insert from the top edge of the ramp and set the ramp aside.
2. Unlatch the link locks indicated in Figure 8 and remove the panels secured by these link
locks.
3. Remove all tape and carefully unwrap the printer by pulling the plastic bag downward.
4. Using a utility knife, cut away and remove the plastic bag’s material ensuring that the bag is
not blocking the fork lift openings or the printer’s wheels.
5. Using a forklift, carefully raise the printer vertically and remove the shipping base.
Figure 6: Opening for Forks
6. Gently lower the printer, until it rests on its wheels.
7. Inspect the printer’s exterior for dents and scratches. Immediately report any damage to
Stratasys and the shipping company.
8. Roll the printer into its approximate operating location.
Caution:
Use care when cutting the plastic bag to avoid scratching the printer’s surfaces.
Caution:
Access the fork lift openings from the back of the printer (Figure 6).
Position the printer to allow at least three feet of clearance on all sides until the
installation process is complete, see “Physical Specifications and Space
Requirements” (page 4). Refer to Chapter 2 of the F123 Series User Guide for final
setup instructions.
Opening for forks

Site Preparation Guide Preparing for Installation
Page 14
9. Open the oven door, cut the cable tie securing the startup materials, and remove the
startup materials from the oven chamber.
10. Open the top cover. Cut the zip ties securing the head and X bridge to the front left corner
of the gantry. Confirm that the toggle plate moves smoothly throughout the gantry.
11. Open the chamber door and remove the orange tape securing the tip wipe assemblies to
the purge chute.
12. Remove the protective film covering the Stratasys logo on the side panels.
Remove Printer from Shipping Base - Ramp Instructions
1. Unlatch the two link locks securing the ramp in a vertical position (Figure 7). Remove the
foam insert from the top edge of the ramp and set the ramp aside.
Figure 7: Ramp Hardware
Warning: Lifting Hazard
Before removing the printer via the ramp, ensure that you have enough manpower
to remove the printer from the shipping base, as the printer is heavy (see
“Dimensions and Weights” (page 4)). A minimum of 2 capable adults should be used
to remove the printer from the shipping base.
Link Lock
(1 per side)
Ramp (in vertical
shipping position)
Foam insert
location

Site Preparation Guide Preparing for Installation
Page 15
2. Unlatch the link locks indicated in Figure 8 and remove the panels secured by these link
locks.
Figure 8: Remove Shipping Base Panels
3. Secure the ramp to the shipping base using the 3 mounting holes on the edge of the
shipping base.
Figure 9: Ramp Connected
Unlatch this
link lock and
remove back
panel by
pulling it
upward.
Unlatch
these link
locks and
remove side
panel by
pulling it
upward.
Caution:
Use care when cutting the plastic bag to avoid scratching the printer’s surfaces.
Secure ramp to
shipping base via 3
post mounting holes

Site Preparation Guide Preparing for Installation
Page 16
4. Remove all tape and carefully unwrap the printer by pulling the plastic bag downward.
5. Using a utility knife cut, away and remove the plastic bag’s material. Ensure that the bag is
not blocking the exit side of the ramp or the printer’s wheels so that the printer can roll
freely down the ramp.
6. Make sure that all four stabilizing pads are in the highest possible position.
7. Carefully roll the printer from the shipping base using the ramp.
8. Inspect the printer’s exterior for dents and scratches. Immediately report any damage to
Stratasys and the shipping company.
9. Roll the printer into its approximate operating location.
10. Open the oven door, cut the cable tie securing the startup materials, and remove the
startup materials from the oven chamber.
11. Open the top cover. Cut the zip ties securing the head and X bridge to the front left corner
of the gantry. Confirm that the toggle plate moves smoothly throughout the gantry.
12. Open the chamber door and remove the orange tape securing the tip wipe assemblies to
the purge chute.
When removing the printer it is recommended that one person guide each side of
the printer.
Position the printer to allow at least three feet of clearance on all sides until the
installation process is complete, see “Physical Specifications and Space
Requirements” (page 4). Refer to Chapter 2 of the F123 Series User Guide for final
setup instructions.