Stryker Renaissance Series User manual

Renaissance Series
1010 Emergency Care Stretcher
1510 PACU Stretcher
721 Advanced Transport Stretcher
MAINTENANCE MANUAL
For Parts or Technical Assistance
1–800–327–0770
IMPORTANT
File in your
maintenance
records

Table of Contents
Introduction
Specifications 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning / Caution / Note Definition 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventative Maintenance
Cleaning 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Biannual Checklist 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Information
Pneumatic Fowler Adjustment 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Board Counterbalance Adjustment 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail Latch Adjustment 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Linkage Adjustment – Dual Side Control Base 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Linkage Adjustment – Dual End Control Base 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly Replacement 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Cover Installation And Removal 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic System Troubleshooting 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Hydraulic Fluid Level 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Of Excess Air (Vacuum) From The Hydraulic System 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Descent Rate Adjustment 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Check Valve Replacement
Replacement Of Valve #1 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Of Valve #2 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Of Valve (Poppet) #3 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjustment 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Lubrication 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly Drawings and Parts Lists
Side Control Base Assembly (with Brakes) 18, 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjuster Assembly 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Cam Assembly 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reduced Length Brake/Steer Base Option 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Base Assembly (with Brakes) 24, 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Brake Pedal Assembly, Foot 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Brake Pedal Assembly, Head 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly with Steerlock 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster and Caster Cover Replacement Kits 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fifth Wheel Assembly 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side Control Base Labeling Assembly (for serial # before 93073000 – 1010,1510 & 9309000 – 721) 30.
End Control Base Labeling Assembly (for serial # before 93073000 – 1010,1510 & 9309000 – 721) 31. .
Side Control Base Assembly (with Jacks) 32, 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Base Assembly, Pump 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Base Assembly, Head End, Left 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Base Assembly, Head End, Right 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side Control Base Hood Assembly 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Base Assembly (with Jacks) 38, 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump Pedal Assembly, Head 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump Pedal Assembly, Foot 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Base Hood Assembly 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Assembly 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Base Assembly 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Folddown Siderail Litter Assembly (for 1010 stretchers with serial # before 93073000) 44–46. . . . . . . . . . . . .
Folddown Siderail Litter Assembly (for 1510 stretchers with serial # before 93073000) 47–49. . . . . . . . . . . . .
Jack Support and Trend. Limiter Assembly 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trend. Limiter Assembly 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short Transfer System to Frame Ass’y (for 1010 & 1510 stretchers with serial # before 93073000) 52. . .
Long Transfer System to Frame Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 53
Short Transfer System Assembly, Left (for 1010 & 1510 stretchers with serial # before 93073000) 54. . .

Table of Contents
Assembly Drawings and Parts Lists (Continued)
Short Transfer System Assembly, Right (for 1010 & 1510 stretchers with serial # before 93073000) 55. .
Long Transfer System Assembly, Left (for 1010 & 1510 stretchers with serial # before 93073000) 56. . .
Long Transfer System Assembly, Right (for 1010 & 1510 stretchers with serial # before 93073000) 57. .
Board Support Assembly 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crank Fowler Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 59. . . . . . . . . . . . . . . .
Crank Fowler Subassembly (for 1010 & 1510 stretchers with serial # before 93073000) 60. . . . . . . . . . . .
Fowler Crankscrew Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 61. . . . . . . . . .
Manual Fowler Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 62. . . . . . . . . . . . . .
Pneumatic Fowler Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 63. . . . . . . . . . .
Pneumatic Fowler to Frame Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 64. . .
Knee Gatch Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 65. . . . . . . . . . . . . . . . .
Foot/Thigh & Midsection Subass’y (for 1010 & 1510 stretchers with serial # before 93073000) 66. . . . . .
Knee Gatch Crankscrew Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 67. . . . . .
Footsection Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 68. . . . . . . . . . . . . . . . .
Foot End Push Handle Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 69. . . . . . .
Head End Push Handle Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 70. . . . . . .
Push Handle Assembly 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail Ass’y, Right & Left 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tethered I.V. Pole Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 73. . . . . . . . . . . .
Tethered I.V. to Frame Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 74. . . . . . . .
Permanent I.V. Pole Assembly (for 1010 stretchers with serial # before 93073000) 75. . . . . . . . . . . . . . . .
Permanent I.V. Pole Mounting Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 76.
Replacement Perm. I.V. Pole Ass’y, Foot (for 1010 & 1510 stretchers with serial # before 93073000) 77.
Replacement Perm. I.V. Pole Ass’y, Head (for 1010 & 1510 stretchers with serial # before 93073000) 78
Replacement Permanent I.V. Pole Ass’y (for 1010 & 1510 stretchers with serial # before 93073000) 79.
Foot Extension/ Defibrillator Tray Ass’y80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fowler X–Ray Cassette Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 81. . . . . .
Fowler X–Ray Cassette Mounting Ass’y (for 1010 & 1510 stretchers with serial # before 93073000) 82. .
Foot Board/Chartholder Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 83. . . . . . .
Upright Oxygen Bottle Holder Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 83.
Heel Stirrup and Support Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 84. . . . .
Right Stirrup Support Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 85. . . . . . . . .
Left Stirrup Support Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 86. . . . . . . . . .
Heel Stirrup Assembly (for 1010 & 1510 stretchers with serial # before 93073000) 87. . . . . . . . . . . . . . . . .
C–Spine Cassette Holder Assembly (for serial # before 93073000 –1010,1510 & 9309000 –721) 87.1. . .
C–Spine Support Pole Assembly (for serial # before 93073000 –1010,1510 & 9309000 –721) 87.2. . . . . .
C–Spine Storage Bracket Assembly (for serial # before 93073000 –1010,1510 & 9309000 –721) 87.3. . .
Litter Assembly (for 721 stretchers with serial # before 9309000) 88–90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Support and Trend. Limiter Assembly 91. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer System Assembly, Right (for 721 stretchers with serial # before 9309000) 92. . . . . . . . . . . . . . .
Transfer System Assembly, Left (for 721 stretchers with serial # before 9309000) 93. . . . . . . . . . . . . . . . .
Pneumatic Fowler to Litter Assembly (for 721 stretchers with serial # before 9309000) 94. . . . . . . . . . . .
Pneumatic Fowler Assembly (for 721 stretchers with serial # before 9309000) 95. . . . . . . . . . . . . . . . . . . .
Manual Fowler to Litter Assembly (for 721 stretchers with serial # before 9309000) 96. . . . . . . . . . . . . . .
Manual Fowler Assembly (for 721 stretchers with serial # before 9309000) 97. . . . . . . . . . . . . . . . . . . . . .
Footsection Assembly (for 721 stretchers with serial # before 9309000) 98. . . . . . . . . . . . . . . . . . . . . . . . .
Siderail Ass’y, Right & Left (for 721 stretchers with serial # before 9309000) 99. . . . . . . . . . . . . . . . . . . . .
Tethered I.V. Pole Assembly (for 721 stretchers with serial # before 9309000) 100. . . . . . . . . . . . . . . . . . . .
Foot Board/Chartholder (for 721 stretchers with serial # before 9309000) 101. . . . . . . . . . . . . . . . . . . . . . . .
Upright Oxygen Bottle Holder (for 721 stretchers with serial # before 9309000) 101. . . . . . . . . . . . . . . . . . .
Defibrillator Tray Assembly (for 721 stretchers with serial # before 9309000) 102. . . . . . . . . . . . . . . . . . . . .
Litter Assembly (for 1010 stretchers with serial # after 93073000) 103–105. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents
Assembly Drawings and Parts Lists (Continued)
Litter Assembly (for 1510 stretchers with serial # after 93073000) 106–108. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stat. Foot End Ass’y (Aluminum) (for 1010 & 1510 stretchers with serial # after 93073000) 109. . . . . . . . .
Stat. Foot End Ass’y (Fiberresin) (for 1010 & 1510 stretchers with serial # after 93073000) 110. . . . . . . . .
Pneumatic Fowler Ass’y (for 1010 & 1510 stretchers with serial # after 93073000) 111. . . . . . . . . . . . . . . . .
Crank Fowler Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 112. . . . . . . . . . . . . . . . .
Fowler Crankscrew Ass’y (for 1010 & 1510 stretchers with serial # after 93073000) 113. . . . . . . . . . . . . . . .
Knee Gatch Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 114. . . . . . . . . . . . . . . . . .
Knee Gatch Assembly (Aluminum) (for 1010 & 1510 stretchers with serial # after 93073000) 115. . . . . . . .
Knee Gatch Assembly (Fiberresin) (for 1010 & 1510 stretchers with serial # after 93073000) 116. . . . . . . .
Knee Gatch Crankscrew Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 117. . . . . . .
Short Transfer System Assembly, Left (for 1010 & 1510 stretchers with serial # after 93073000) 118. . . . .
Short Transfer System Assembly, Right (for 1010 & 1510 stretchers with serial # after 93073000) 119. . .
Foot End Push Handle to Frame Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 120
2–Stage I.V. Ass’y, Head & Foot (for 1010 & 1510 stretchers with serial # after 93073000) 121. . . . . . . . .
2–Stage I.V. Pole Assembly 122. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–Stage I.V. Ass’y, Head & Foot (for 1010 & 1510 stretchers with serial # after 93073000) 123.1. . . . . . . . . .
3–Stage I.V. Pole Assembly (for 1010 stretchers with serial # after 93073000) 123.2. . . . . . . . . . . . . . . . . . . .
3–Stage I.V. Pole Assembly (for 1510 stretchers with serial # after 93073000) 123.3. . . . . . . . . . . . . . . . . . . .
2nd Stage Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 123.4. . . . . . . . . . . . . . . . . . . .
3rd Stage Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 123.5. . . . . . . . . . . . . . . . . . . .
Tethered I.V. Pole Mounting Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 124. . . .
Tethered I.V. Pole Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 125. . . . . . . . . . . . .
Tethered I.V. Pole Trough Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 126. . . . . .
Litter Assembly (for 721 stretchers with serial # after 9309000) 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short Transfer System to Frame Ass’y (for 721 stretchers with serial # after 9309000) 130. . . . . . . . . . . .
Long Transfer System to Frame Assembly (for 721 stretchers with serial # after 9309000) 131. . . . . . . . .
Long Transfer System Assembly, Left (for 721 stretchers with serial # after 9309000) 132. . . . . . . . . . . . .
Long Transfer System Assembly, Right (for 721 stretchers with serial # after 9309000) 133. . . . . . . . . . . .
Pneumatic Fowler Assembly (for 721 stretchers with serial # after 9309000) 134. . . . . . . . . . . . . . . . . . . . .
Manual Fowler Assembly (for 721 stretchers with serial # after 9309000) 135. . . . . . . . . . . . . . . . . . . . . . . .
2–Stage I.V. Ass’y, Head & Foot (for 721 stretchers with serial # after 9309000) 135.1. . . . . . . . . . . . . . . . . .
2–Stage I.V. Pole Assembly (for 721 stretchers with serial # after 9309000) 135.2. . . . . . . . . . . . . . . . . . . . . .
3–Stage I.V. Assembly, Head & Foot (for 721 stretchers with serial # after 9309000) 135.3. . . . . . . . . . . . . .
3–Stage I.V. Pole Assembly (for 721 stretchers with serial # after 9309000) 135.4. . . . . . . . . . . . . . . . . . . . . .
2nd Stage Assembly (for 721 stretchers with serial # after 9309000) 135.5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
3rd Stage Assembly (for 721 stretchers with serial # after 9309000) 135.6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tethered I.V. Pole Mounting Assembly (for 721 stretchers with serial # after 9309000) 136. . . . . . . . . . . . .
Tethered I.V. Pole Trough Assembly (for 721 stretchers with serial # after 9309000) 137. . . . . . . . . . . . . . .
C–Spine Cassette Holder Assembly (for serial # after 93073000 –1010,1510 & 9309000 –721) 138. . . .
Defibrillator Tray Assembly (for serial # after 93073000 –1010,1510 & 9309000 –721) 139. . . . . . . . . . . .
Foot Board/Chartholder Assembly (for serial # after 93073000 –1010,1510 & 9309000 –721) 140. . . . . .
Upright Oxygen Bottle Holder Assembly (for serial # after 93073000 –1010,1510 & 9309000 –721) 140.
Fowler X–Ray Cassette Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 141. . . . . . . .
X–Ray Cassette Mounting Assembly (for 1010 & 1510 stretchers with serial # after 93073000) 142. . . . . .
Side Control Base Labeling Ass’y 143, 144. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side Control Graphics 145, 146. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Base Labeling Ass’y 147, 148. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Graphics 149, 150. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Parts 151. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty
Obtaining Parts and Service 152. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Warranty Coverage 152. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Authorization 153. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freight Damage Claims 153. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3
Introduction
INTRODUCTION
This manual is designed to assist you with the operation and maintenance of the 1010 Emergency Care
Stretcher, the 1510 PACU Bed and the 721 Advanced Transport Stretcher. Read it thoroughly before using
the equipment or beginning any maintenance on it.
SPECIFICATIONS
1010 1510 721
Maximum Weight Capacity 500 pounds 500 pounds 500 pounds
Overall Bed Length \ Width 83 1/2”\ 31 1/2”81 1/2”\ 34”81”/30”
Minimum \ Maximum Bed Height 22”\ 35”22”\ 35”24.5”/38.0”
Fowler Angle 0 to 90 degrees 0 to 90 degrees 0 to 90 degrees
Knee Gatch Angle 0 to 35 degrees 0 to 35 degrees N/A
Trendelenberg \ Reverse Trendelen-
berg +12 to –18 degrees +12 to –18 degrees +12 to –12 degrees
WARNING / CAUTION / NOTE DEFINITION
The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.
WARNING
The personal safety of the patient or user may be involved. Disregarding this information could result in injury
to the patient or user.
CAUTION
These instructions point out special procedures or precautions that must be followed to avoid damaging the
equipment.
NOTE
This provides special information to make maintenance easier or important instructions clearer.
WARNING
Patients should be discouraged from sitting directly on the ends of the stretcher. Excessive weight will cause
the litter surface to tip up, possibly causing patient injury.

Preventative Maintenance
4
CHECKLIST (PERFORM A MINIMUM OF TWICE A YEAR)
All fasteners secure (reference all assembly prints)
Siderails move and latch properly (page 7)
All casters lock with brake pedal engaged (page 16)
Steer function working properly
All casters secure and swivel properly
Body restraints working properly
I.V. pole intact and operating properly (page 73–79, 121–126 or 135.1–137.2)
Oxygen bottle holder intact and operating properly (page 37, 41, 101 or 140)
Fowler operates and latches properly
Knee Gatch operates properly (page 65)
Trendelenberg/Reverse Trendelenberg operating properly
No rips or cracks in mattress cover
Transfer boards intact and operating properly (page 6)
Arm board support levers intact and operating properly (page 58)
Ground chain intact
No leaks at hydraulic connections
Hydraulic jacks holding properly (page 11)
Hydraulic drop rate set properly (page 13)
Hydraulic oil level sufficient (page 12)
Lubricate where required, including the brake adjuster assembly and brake cam (page 16)
Accessories and mounting hardware in good condition and working properly
Serial No.______________
______________
______________
______________
______________
Completed By:_________________________________ Date:_____________

Cleaning
5
Clean Velcro AFTER EACH USE. Saturate Velcro with disinfectant and allow disinfectant to evaporate. (Ap-
propriate disinfectant for nylon Velcro should be determined by the hospital.)
In general, when used in those concentrations recommended by the manufacturer, either phenolic type or
quaternary type disinfectants can be used with Staph–Chek fabrics. Iodophor type disinfectants are not rec-
ommended for use on Staph–Chek fabrics because staining may result. The following products have been
tested by the Herculite Laboratory and have been found not to have a harmful effect on Staph–Chek fabrics
WHEN USED IN ACCORDANCE WITH MANUFACTURERS RECOMMENDED DILUTION.*
TRADE NAME DISINFECTANT
TYPE
MANUFACTURER *MANUFACTURER’S RECOMMENDED
DILUTION
A33 Quaternary Airwick (Professional Products Division) 2 ounces/gallon
A33 (dry) Quaternary Airwick (Professional Products Division) 1/2 ounce/gallon
Beaucoup Phenolic Huntington Laboratories 1 ounce/gallon
Blue Chip Quaternary S.C. Johnson 2 ounces/gallon
Elimstaph Quaternary Walter G. Legge 1 ounce/gallon
Franklin
Phenomysan
F2500
Phenolic Purex Corporation 1 1/4 ounce/gallon
Franklin Sentinel Quaternary Purex Corporation 2 ounces/gallon
Galahad Phenolic Puritan Churchill Chemical Company 1 ounce/gallon
Hi–Tor Quaternary Huntington Laboratories 1/2 ounce/gallon
LPH Phenolic Vestal Laboratories 1/2 ounce/gallon
Matar Phenolic Huntington Laboratories 1/2 ounce/gallon
Omega Quaternary Airwick (Professional Products Division) 1/2 ounce/gallon
Quanto Quaternary Huntington Laboratories 1 ounce/gallon
Sanikleen Quaternary West Chemical Products 2 ounces/ gallon
Sanimaster II Quaternary Service Master 1 ounce/gallon
Vesphene Phenolic Vestal Laboratories 1 1/4 ounce/ gallon
Quaternary Germicidal Disinfectants, used as directed, and/or Chlorine Bleach products, typically 5.25% So-
dium Hypochlorite in dilutions ranging between 1 part bleach to 100 parts water, and 2 parts bleach to 100
parts water are not considered mild detergents. These products are corrosive in nature and may cause dam-
age to your stretcher if used improperly. If these types of products are used to clean Stryker patient handling
equipment, measures must be taken to insure the stretchers are rinsed with clean water and thoroughly dried
following cleaning. Failure to properly rinse and dry the stretchers will leave a corrosive residue on the surface
of the stretcher, possibly causing premature corrosion of critical components. Failure to follow the above
directions when using these types of cleaners may void this product’s warranty.
REMOVAL OF IODINE COMPOUNDS
This solution may be used to remove iodine stains from mattress cover and foam footrest pad surfaces.
1. Use a solution of 1–2 tablespoons Sodium Thiosulfate in a pint of warm water to clean the stained area.
Clean as soon as possible after staining occurs. If stains are not immediately removed, allow solution to
soak or stand on the surface.
2. Rinse surfaces which have been exposed to the solution in clear water before returning bed to service.

6
Service Information
PNEUMATIC FOWLER ADJUSTMENT
Required Tools:
3/32 Hex Allen Wrench 5/8 Open End Wrench
1/8 Hex Allen Wrench Channel Lock Pliers
3/16 Hex Allen Wrench Towel or Cloth
7/16 Open End Wrench Thread ”Locktite”
Adjustment Procedure:
1. Refer to drawings 1010–31–90 and 1510–31–25 (Pneumatic Fowler Assembly, page 63) or 721–31–70
(Pneumatic Fowler Assembly, page 95).
2. For easier access, move Fowler to 75 degrees or higher.
3. Using a 3/32 hex Allen wrench, remove set screws (N), located in center of yokes (D).
4. Wrap a towel or cloth around the gas cylinder actuator shaft(s) so as not to mark the shaft. Using channel
lock pliers, turn actuator shaft(s) into yoke(s) (D) until tight.
5. Using thread locktite, reinstall set screws (N).
6. While holding the jam nut spacers (R) with a 5/8 open end wrench, turn the adjustment screws (P) using
a 3/16 hex Allen wrench until they JUST touch the cylinder pins.
7. Bring the Fowler fully down, and with the handle fully released, using a 1/8 hex Allen wrench, tighten the
bottom set screws (S) so the handle is lifted 1/8–1/4 inch above the spine tube. Both set screws must
touch the handle. Using a 7/16 open end wrench, tighten the jam nuts (Y) on these set screws.
8. Be sure the Fowler will travel from flat to at least 90 degrees. If it doesn’t, turn each adjustment screw (P)
clockwise 1/2 turn. Repeat until at least 90 degrees of travel is achieved.
9. Lower the Fowler to a 5–10 degree angle and release the handle. Apply approximately 50 pounds down-
ward to the end of the Fowler. If either side drifts down, turn the adjustment screw (P) on that side 1/4
turn counterclockwise. Repeat until the Fowler is firm with 50 pounds applied.
10. While holding the adjustment screws (P), tighten the jam nut spacers (R).
TRANSFER BOARD COUNTERBALANCE ADJUSTMENT
Required Tools:
7/16 Open End Wrench
Adjustment Procedure:
1. Raise the transfer board to the full up position.
2. Unhook the extension spring at the eye bolt.
3. Using a 7/16 open end wrench, loosen the jam nut at the eye bolt.
4. Adjust the eye bolt to the desired position.
5. Tighten the jam nut.
6. Hook the extension spring to the eye bolt.
7. Allow the transfer board to lower on its own.
8. Repeat steps 1–7 until the desired counterbalance is achieved.

7
Service Information
SIDERAIL LATCH ADJUSTMENT
Required Tools:
1/8 Hex Allen Wrench
WARNING
The siderail latch adjustment is pre–set at the factory, and there should not normally be a need for readjust-
ment. If adjustment must be done it is important to follow the procedure below. If it is not done properly, injury
to the patient or user could occur.
Adjustment Procedure:
1. Using a 1/8 hex Allen wrench, adjust the hex Allen screw located on the latch assembly opposite the latch.
Turning the Allen screw clockwise will DECREASE the amount of ”play”in the latching mechanism. Turn-
ing counterclockwise will INCREASE the amount.
NOTE
The amount of ”play”in the siderail, when in full up engaged position, should be approximately 1/8 to 3/16
inches.
CAUTION
Too much ”play”when the siderail is in the full up engaged position will give the siderail the appearance of
being unstable and could also cause premature wearing of the latch system.
Too little ”play”will obstruct the latch and keep it from engaging completely in the full up position, which may
cause damage to the latch and/or injury to the patient or user.

8
Service Information
PEDAL LINKAGE ADJUSTMENT –DUAL SIDE CONTROL BASE
Required Tools:
3/32 Hex Allen Wrench
7/16 Open End Wrench
1/2 Open End Wrench
(2) Wooden blocks (10 –12 inches in length)
Adjustment Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. To adjust the foot end descent pedal, use a 5/32 hex Allen wrench to loosen the set screw (C) in the stop
collar (D) on the release rod. Hold the pedal parallel to the floor and slide the collar up to the bracket on
the release rod. Tighten the set screw on the stop collar. Be sure the head end and foot end descent
pedals are level with each other. Repeat for the head end pedal, if necessary.
4. Once the pedals are level, be sure the paddle on the end of the release rod for the foot end jack is slightly
touching the actuating stem on the jack base. If it is not, use a 3/32 hex Allen wrench to loosen the set
screw on the paddle hub. Adjust the paddle to JUST touch the stem of the jack. Tighten the set screw
in the paddle hub. Repeat for the head end jack, if necessary.
5. Depress the pedal for the foot end jack. The jack should start to descend about the same time the paddle
on the end of the rod contacts the sleeve on the jack actuating stem. The bracket on the foot pedal body
should hit the stop screw (B). Any further movement could cause damage to the stem components inside
the jack housing. To adjust the stop screw, use a 1/2 open end wrench to loosen the hex jam nut (A).
Turn the screw and re–tighten the hex jam nut. Repeat for the head end jack.
6. Pump the litter up to full height.
7. Step on both descent pedals at the same time. Both ends of the litter should lower with the foot end lower-
ing slightly faster than the head end. If it does not, refer to the procedure for adjusting the jack descent
rate.
8. Remove the wooden blocks supporting the base hood. Use the pedal cut–outs on the side of the hood
as a guide for proper re–positioning.

9
Service Information
PEDAL LINKAGE ADJUSTMENT –DUAL END CONTROL BASE
Required Tools:
7/16 Open End Wrench
1/2 Open End Wrench
(2) Wooden Blocks (10 –12 inches in length)
Adjustment Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. The descent pedals should be level with each other and there should be approximately 4 inches between
the floor and the bottom of the pedal. To raise the pedal height, use a 1/2 open end wrench to loosen the
hex jam nut (E). Using your hand, turn the screw (D) into the bracket. To lower the pedal height, loosen
the screw. Tighten the hex jam nut (E) after the correct height is achieved.
4. Once the pedals are level, the release rod can be adjusted. Using a 7/16 wrench, turn nut (B) clockwise
to shorten the release length and counterclockwise to increase the length.
5. Depress the pedal and be sure the jack descent is triggered when the pedal is approximately one inch from
the floor. The descent should stop when the pedal is released and the jack height should hold. Repeat
the above procedures for the descent pedal at the other end of the bed.
6. After adjusting each descent pedal individually, depress both pedals at the same time. Both jacks should
start descending when the pedals are approximately one inch from the floor. The foot end should lower
slightly faster than the head end. If it does not, see procedure for adjusting the jack descent rate.
7. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.

10
Service Information
CASTER ASSEMBLY REPLACEMENT*
Required Tools:
1/8 Roll Pin Punch Drill with 1/8 inch Drill Bit
Flat Punch (any size larger than 1/8) Hammer
Needle Nose Pliers Floor Jack
3/4 Inch Wrench (2) Wooden Blocks (10 –12 inches in length)
1 Inch Wrench Torque Wrench (w/ Ft. Lbs. Adjust.)
Replacement Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. Using a 1/8 roll pin punch and hammer, remove roll pin located in center of lug nut holding wheel assembly
to base frame.
4. Carefully remove plastic wheel covers.
5. Using a floor jack, lift base frame approximately 4 inches off the ground.
6. While holding cap screw with a 3/4 inch wrench, turn lug nut with a 1 inch wrench to loosen wheel assembly
from base frame. Remove wheel.
7. Install the new wheel assembly with new lug nut and tighten down to 60 –65 foot–pounds torque.
WARNING
Never reuse the old lug nut, cap screw or roll pin once removed from base frame.
8. Lower the floor jack and set aside to be used, if needed, with another wheel.
9. Drill a 1/8 hole in center of lug nut, going completely through the lug nut.
CAUTION
Be careful not to ”oblong”the hole in the lug nut when drilling.
10. Using needle nose pliers, hold on to roll pin and tap into place. Finish driving roll pin with a flat head punch
and a hammer until flush with the lug nut.
11. Install plastic wheel covers onto wheel.
12. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.
1/8 Inch
Through Lug Nut
(60–65 Ft.–Lb.)
Support Tube
1 Inch
Dia.
Roll Pin
*Replacement Part Number 715–100–127 (Caster and Cover Assembly)

Service Information
10.1
CASTER COVER INSTALLATION AND REMOVAL
Double Prongs
Single Prong
align cover with axle nut or bolt head, as shown.
Push down on the opposite side of the cover until
single prong engages with caster horn.
Push with palm on cover until
ProperlyAttached
Cover
To remove wheel cover, insert large screwdriver into cut–out in
side of wheel cover and into the space between the double prongs.
Pry up cover to disengage double prongs and push sharply upward
double prongs engage.
1.
2.
3.
Looking through the larger of the two side cut–outs,
Top View (Cut–Away)
Top View (Cut–Away)
Top View (Cut–Away)
to disengage single prong.

Service Information
10.2
CASTER MAINTENANCE
Required Tools:
5/8”Wrench
11/16”Wrench
Maintenance Procedure:
AB
C
D
Remove the plastic caster cover (see page 10.1).
Using the 5/8”wrench and the 11/16”wrench, remove the centerlock nut (item A) from the through bolt
(item B) for the caster wheel.
Support the corner of the stretcher where the wheel is being removed and remove the through bolt (item
B) and the molded wheel (item C) .
Clean the through bolt, molded wheel, and the inside of the caster horn (item D) removing any dirt and
debris. Ensure the bearings in the molded wheel spin freely and easily.
Replace the molded wheel and the through bolt.
Replace the centerlock nut on the through bolt and use the 5/8”and 11/16”wrenches to tighten it securely.

Service Information
HYDRAULIC SYSTEM TROUBLESHOOTING
NOTE
Be sure the pedal linkage has been adjusted properly before beginning service on the jacks (see page 8 or
page 9).
PROBLEM/SYMPTOM SOLUTION
Jack will not raise to full height. Add hydraulic fluid (see p.12). Check for leaks.
Jack will not hold in raised position. Close the needle valve completely. If the jack
holds, replace valve #1 (see p. 14). If the jack
does not hold, replace valve #2 (see p. 15).
Jack will not pump up and the jack actuator rod
does not move. Close the needle valve. If the jack will now pump
up, replace valve #1. If the jack still will not pump
up after closing the needle valve, replace valve #3
(see p. 15).
Jack will not pump up but the jack actuator rod
does move when the pump pedal is activated. Replace valve #2 (see p. 15).
Jack will not pump up and the jack actuator rod
may or may not move. Remove excess air (vacuum) in system (see p. 12).
Contact Stryker technical service at 1–800–327–0770 for further assistance.

Service Information
12
CHECKING HYDRAULIC FLUID LEVEL
Required Tools:
3/8 Open End Wrench
3/4 Open End Wrench
Procedure:
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the jacks.
1. Using a 3/8 open end wrench, remove square head set screws from both head and foot end jack support
tubes. Remove litter top and set aside.
2. Lift base hood off base frame and set aside.
3. Be sure there are no hydraulic leaks. If there are, jack replacement will be necessary.
4. Lower the jack to the full down position.
5. Using a 3/4 open end wrench, slowly turn the fill plug located on the side of the reservoir counterclockwise
to allow excess system pressure to vent. Remove the fill plug.
6. The hydraulic fluid should be visible at the bottom of the fill hole. If it is not, add Mobil Aero HFA hydraulic
fluid (Stryker part number 2020–70–475) until the fluid is visible at the bottom of the fill hole. Replace the
fill plug.
CAUTION
Use of other types of oil may damage hydraulic units.
7. Replace the hood and the litter.
REMOVAL OF EXCESS AIR (VACUUM) FROM THE HYDRAULIC SYSTEM
Procedure:
1. Verify all hydraulic linkages are secure and operating properly (see pedal linkage adjustment procedure
page 8 or 9).
2. Using pump pedal, actuate system several times. This will force the air through the system and the jack
should now pump up.

Service Information
13
JACK DESCENT RATE ADJUSTMENT
Required Tools:
Screwdriver
(2) Wooden Blocks (10 –12 inches in length)
Adjustment Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. The descent rate needle valve is located on the base of the jack. Turning the needle valve clockwise, with
a screwdriver, will decrease the rate of descent. Turning it counterclockwise will increase the rate of de-
scent.
4. Adjust the needle valve so that the foot end of the stretcher descends slightly faster than the head end.
NOTE
The larger percentage of a patient’s weight is located in the torso area. Adjust descent rate accordingly.
5. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.
NOTE
The jack descent rate was preset at the factory to drop the foot end faster than the head. It is recommended
that the foot drop faster to avoid patient disorientation.

Service Information
14
HYDRAULIC CHECK VALVE REPLACEMENT
Required Tools:
3/8 Open End Wrench Stiff Wire (with bent, pointed end) Small Needle Nose Pliers
3/4 Open End Wrench Torque Wrench (with Ft. Lbs. adjust.)
7/32 Hex Allen Wrench 1/2 Inch Diameter Rod
Replacement of Valve #1
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the stretcher.
1. Using a 3/8 open end wrench, remove square head set screws from both head and foot end jack support
tubes. Remove litter top and set aside.
2. Lift base hood off base frame and set aside.
3. Lower the jack to full down position. The actuator must be manually lowered while depressing the appropri-
ate release pedal.
4. Remove the pin body assembly (4) with a 3/4 open end wrench and discard the housing gasket (5).
NOTE
Although the hydraulic fluid is not under pressure, some fluid loss will occur. The fluid loss should be minimal
but covering the floor is advisable.
5. Using a 7/32 hex Allen wrench, remove the valve plug (6).
6. Using a stiff wire with a bent, pointed end, remove and discard the valve (1) and the seal (7).
7. Install the new seal (7) flat to the bottom of its hole with a 1/2 inch diameter rod and install the new valve
(1) with the beveled end out (as shown in the illustration).
8. Install the valve plug (6) with the countersunk end first and the beveled end out. Tighten to 10 foot pounds
torque.
9. Install the pin body assembly (4) with the new housing gasket (5) and tighten to 10 foot pounds torque.
10. Pump up the jack to the maximum height. Apply weight to be sure the jack holds its position and there
are no hydraulic leaks before replacing the base hood and the litter.
ITEM PART NO. PART NAME
1 926–20–153 Check Valve
2 926–20–153 Check Valve
3 715–1–341 Poppet
4 715–100–312 Pin Housing Assembly*
715–270–100 Valve Assembly**
5 715–1–330 Housing Gasket
6 715–1–309 Valve Plug
7 926–20–154 Seal
8 715–1–101 Base Plug
9 926–20–156 Seal
10 715–1–309 Valve Plug
11 926–20–154 Seal
12 715–1–301 Base Plug
13 926–20–156 Seal
14 390–2–134 Conical Comp. Spring
* Used on jack part number 715–100–310.
** Used on jack part number 715–270–10.
(see label on side of jack reservoir for jack part number)
FILLER PLUG
3
14
12
13

Service Information
15
HYDRAULIC CHECK VALVE REPLACEMENT (CONT’D)
Replacement of Valve #2
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the jacks. Lower the jack rod completely to relieve the pressure on the pump piston side of the
jack. This will prevent large hydraulic fluid loss and possible damage when the base plugs are removed.
1. Remove the base plug (8) and discard the seal (9).
2. Remove the valve plug (10).
3. Using a stiff wire with a bent, pointed end, remove the valve (2) and the seal (11) and discard the seal.
4. Install the new seal (11) flat to the bottom of its hole with a 1/2”diameter rod.
5. Install the new valve (2) with the beveled end out (as shown in the illustration).
6. Install the valve plug (10) and tighten to 10 foot–pounds torque.
7. Install the new seal (9) with the base plug (8) and tighten to 10 foot–pounds torque.
8. Pump up the jack to the maximum height.
9. Be sure there are no hydraulic leaks before replacing the base hood and the litter.
Replacement of Valve (Poppet) #3
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the jacks. Lower the jack rod completely to relieve the pressure on the pump piston side of the
jack. This will prevent large hydraulic fluid loss and possible damage when the base plugs are removed.
1. Remove the base plug (12) and discard the seal (13).
2. Remove the compression spring (14).
3. Using a small needle nose pliers, remove the poppet (3).
4. Install the new poppet (3).
5. Install the compression spring (14).
6. Install the new seal (13) and the base plug (12) and tighten to 10 foot–pounds torque.
7. Pump up the jack to the maximum height to check its operation.
8. Check for hydraulic leaks before replacing the base hood and the litter.

Service Information
16
BRAKE ADJUSTMENT
Required Tools:
3/32”Hex Allen Wrench
Pry Bar
Thread ”Locktite”
BASE LUBRICATION
1. Lubricate brake adjuster rod
around area shown with MPG–2
grease or equivalent.
Do not grease area shown.