Stryker SYSTEM G 7305-001-000 User manual

2016-05 7305-001-700 Rev-A www.stryker.com
Instructions For Use
ENGLISH (EN)
ESPAÑOL (ES)
ITALIANO (IT)
PORTUGUÊS (PT)
TÜRKÇE (TR)
РУССКИЙ (RU)
中文 (ZH)
한국어 (KO)
STRYKER SYSTEM G™
Rotary Drill
7305-001-000
Rotary Drill Attachments
7307-XXX-XXX Series
4103-XXX-XXX Series

2 www.stryker.com
EN 7305-001-700 Rev-A
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . 3
Audience . . . . . . . . . . . . . . . . . . . . 3
Conventions . . . . . . . . . . . . . . . . . . . 3
Contact Information . . . . . . . . . . . . . . . 3
Intellectual Property . . . . . . . . . . . . . . . 3
Indications For Use . . . . . . . . . . . . . . . . . . 3
Contraindications . . . . . . . . . . . . . . . . . . . 3
Safety Directives . . . . . . . . . . . . . . . . . . . 3
For Use With . . . . . . . . . . . . . . . . . . . . . 4
Power and Care Components . . . . . . . . . . . 4
Attachments and Cutting and Fixation Tools . . . . 4
Wire and Pin Collets . . . . . . . . . . . . . 4
Keyed Chucks . . . . . . . . . . . . . . . . 4
Keyless Chucks . . . . . . . . . . . . . . . 4
Drill Attachments. . . . . . . . . . . . . . . 4
Reamer Attachments. . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . 5
Handpiece. . . . . . . . . . . . . . . . . . . . 5
Safety Switch . . . . . . . . . . . . . . . . . . 6
Attachments . . . . . . . . . . . . . . . . . . . 6
Wire and Pin Collets . . . . . . . . . . . . . 6
Keyed Chucks . . . . . . . . . . . . . . . . 6
Keyless Chucks . . . . . . . . . . . . . . . 6
Drill and Reamer Attachments . . . . . . . . 7
Definitions . . . . . . . . . . . . . . . . . . . . . . 7
Instructions . . . . . . . . . . . . . . . . . . . . . 7
To Process the Equipment . . . . . . . . . . . . 7
To Charge a Power Module . . . . . . . . . . . . 7
To Install a Power Module . . . . . . . . . . . . 8
Sterile Assistant . . . . . . . . . . . . . . . 8
Circulating Assistant . . . . . . . . . . . . . 8
Sterile Assistant . . . . . . . . . . . . . . . 9
To Install an Attachment . . . . . . . . . . . . . 9
To Install and Remove a Cutting or Fixation Tool . .10
Wire and Pin Collets . . . . . . . . . . . . .10
Keyed Chucks . . . . . . . . . . . . . . . 11
Keyless Chucks . . . . . . . . . . . . . . 11
Drill and Reamer Attachments . . . . . . . .12
To Operate a Handpiece . . . . . . . . . . . . .12
To Remove an Attachment . . . . . . . . . . . .13
To Remove a Power Module . . . . . . . . . . .13
Specifications . . . . . . . . . . . . . . . . . . . .14
Handpiece. . . . . . . . . . . . . . . . . . . .14
Attachments . . . . . . . . . . . . . . . . . . .14
Wire and Pin Collets . . . . . . . . . . . . .14
Keyed Chucks . . . . . . . . . . . . . . . .15
Keyless Chucks . . . . . . . . . . . . . . .15
Drill Attachments. . . . . . . . . . . . . . .15
Reamer Attachments. . . . . . . . . . . . .16
Transfer Shield. . . . . . . . . . . . . . . . . .16
Product Safety Compliance . . . . . . . . . . . . . .16
Electromagnetic Compatibility . . . . . . . . . . . . .17

7305-001-700 Rev-A EN
www.stryker.com 3
Introduction
This instructions for use manual contains information
intended to ensure the safe, effective, and compliant use
of your product.
Audience
This manual is intended for in-service trainers, physicians,
nurses, and surgical technologists. Keep and consult this
reference manual during the life of the product.
Conventions
The following conventions are used in this manual:
▪ A WARNING highlights a safety-related issue. ALWAYS
comply with this information to prevent patient and/or
healthcare staff injury.
▪ A CAUTION highlights a product reliability issue.
ALWAYS comply with this information to prevent
product damage.
▪ A NOTE supplements and/or clarifies procedural
information.
Contact Information
For additional information, including safety information, in-
service training, or current literature, contact your Stryker
sales representative or call Stryker customer service
at 1-269-323-7700 or 1-800-253-3210. Outside the US,
contact your nearest Stryker subsidiary.
Intellectual Property
Trademarks not the property of Stryker Corporation are
the property of their respective owners.
Indications For Use
The STRYKER SYSTEM G Rotary Drill (handpiece) is
a surgical battery-powered instrument intended for use
during a variety of orthopedic and trauma procedures
to provide power to operate various accessories or
attachments, which may include a pin/wire driver, a driver
bit, and/or a drill bit.
This handpiece is designed for surgical procedures where
hard tissue and/or bone must be reamed, drilled and/or
fixated with screws, including, but not limited to, the hand
wrist, elbow, shoulder, foot, ankle, knee, and hip.
Contraindications
None known.
Safety Directives
WARNINGS:
▪ Before using this equipment, read and understand the
instructions for use. Pay particular attention to safety
information.
▪ Only trained and experienced healthcare professionals
should use this equipment.
▪ The healthcare professional performing any procedure
is responsible for determining the appropriateness of
this equipment and the specific technique used for
each patient. Stryker does not recommend surgical
procedure or technique.

4 www.stryker.com
EN 7305-001-700 Rev-A
For Use With
This section identifies components intended to be used
with the equipment to obtain a safe combination.
WARNINGS:
▪ Use only Stryker-approved equipment, unless
otherwise specified.
▪ Use of unapproved electrical equipment may result
in increased electromagnetic emissions or decreased
electromagnetic immunity of the system.
NOTE: For a complete list of components or ordering
information, contact your Stryker sales representative or
call Stryker customer service. See the Contact Information
section. Outside the US, contact your nearest Stryker
subsidiary.
Power and Care Components
Description REF
STRYKER SYSTEM G Transfer
Shield
7304-120-000
STRYKER SYSTEM G Power
Module
7309-120-000
STRYKER SYSTEM G Charger,
2-Bay
7310-120-000
STRYKER SYSTEM G Sterilization
Cases
7302-120-000
7302-130-000
Attachments and Cutting and
Fixation Tools
WARNING: All cutting and fixation tools are intended
for single use only.
Wire and Pin Collets
NOTE: Wire and pin collets REF 4103-063-000, 4103-
126-000S3, and 4103-126-000 are not compatible with
STRYKER SYSTEM G.
Attachment REF Tools
STRYKER
SYSTEM G
Wire Collet
7307-001-000 Kirschner wires and
Steinmann pins
from 0.7 to 1.8 mm
in diameter
STRYKER
SYSTEM G Pin
Collet, Small
7307-002-000 Kirschner wires and
Steinmann pins
from 2.0 to 3.2 mm
in diameter
STRYKER
SYSTEM G Pin
Collet, Large
7307-003-000 Kirschner wires and
Steinmann pins
from 3.0 to 4.2 mm
in diameter
Keyed Chucks
NOTE: Each chuck is supplied with a chuck key (REF
1331-001-009)
Attachment REF Tools
1:1 1/4 inch
(6.4 mm) Keyed
Chuck
4103-131-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
High Torque 1/4
inch (6.35 mm)
Drill with Chuck
2:1 with Key
4103-180-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
3.25:1 1/4 inch
(6.4 mm) Keyed
Chuck
4103-231-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Keyless Chucks
NOTE: The Keyless Chuck Adaptor (REF 4103-082-131) is
intended for use with standard Trinkle attachments.
Attachment REF Tools
Keyless Chuck
Adaptor
4103-082-131 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Keyless Drill
Attachment
4103-133-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Drill Attachments
Attachment REF Tools
1:1 AO Small
Drill
4103-110-000 Drill bits, taps,
automatic
screwdrivers, and
tools with AO snap-
lock shanks
1:1 Hudson 4103-113-000 Drill bits, reamers,
taps, automatic
screwdrivers, and
tools with Hudson
fittings
1:1 Hudson/
Modified Trinkle
4103-135-000 Drill bits, reamers,
automatic
screwdrivers, and
tools with Hudson
or modified Trinkle
fittings
1:1 Trinkle 4103-160-000 Drill bits, reamers,
automatic
screwdrivers, and
tools with standard
Trinkle fittings

7305-001-700 Rev-A EN
www.stryker.com 5
Reamer Attachments
Attachment REF Tools
3.25:1 AO
Large Reamer
4103-210-000 Drill bits, flexible
reamers, automatic
screwdrivers, and
tools with AO snap-
lock shanks
3.25:1 Hudson 4103-213-000 Drill bits, reamers,
taps, automatic
screwdrivers, and
tools with Hudson
fittings
3.25:1 Hudson/
Modified Trinkle
4103-235-000 Drill bits, reamers,
automatic
screwdrivers, and
tools with Hudson
or modified Trinkle
fittings
3.25:1 Trinkle 4103-260-000 Drill bits, reamers,
automatic
screwdrivers, and
tools with standard
Trinkle fittings
4:1 Hudson 4103-413-000 Drill bits, reamers,
taps, automatic
screwdrivers, and
tools with Hudson
fittings
4:1 Hudson/
Modified Trinkle
4103-435-000 Drill bits, reamers,
automatic
screwdrivers, and
tools with Hudson
or modified Trinkle
fittings
Features
Handpiece
A
FE
C
B
D
A Safety Switch – Locks one or both of the
triggers.
B Release Lever – Push to release an
attachment from the handpiece.
C Reverse Trigger – Controls the variable
speed operation of the handpiece in a
counterclockwise direction.
D Forward Trigger – Controls the variable
speed operation of the handpiece in a
clockwise direction.
E Door – Opens to allow installation of a
power module.
F Latch – Secures the door.

6 www.stryker.com
EN 7305-001-700 Rev-A
Safety Switch
Forward Mode – Only the forward
trigger is functional. The reverse
trigger is locked to prevent
inadvertent operation of the
handpiece in a counterclockwise
direction.
Forward/Reverse Mode – Both
triggers are functional.
Safe Mode – Both triggers are
locked to prevent inadvertent
operation of the handpiece.
Attachments
Wire and Pin Collets
C
BA
A Clamping Lever – Secures and releases the
wire or pin from the attachment.
B Pre-adjust Knob – Allows the collet to
receive wires and pins of various diameters.
C J-Notch – Secures the attachment in the
handpiece.
Keyed Chucks
A
C
B
A Jaws – Secure the cutting tool in the
attachment.
B Chuck Key – A tool used to open and close
the jaws.
C J-Notch – Secures the attachment in the
handpiece.
Keyless Chucks
C
BA
D
A Lock Switch – Locks the collar to prevent
inadvertent operation of the attachment (REF
4103-133-000 only).
B Chuck – Rotates to open and close the
jaws.
C Jaws – Secure the cutting tool in the
attachment.
D J-Notch – Secures the attachment in the
handpiece.

7305-001-700 Rev-A EN
www.stryker.com 7
Drill and Reamer Attachments
A
B
A Retaining Collar – Slide to allow installation
of a cutting tool.
B J-Notch – Secures the attachment in the
handpiece.
Definitions
The symbols located on the equipment and/or labeling
are defined in this section and/or in the Symbol Definition
Chart. See the Symbol Definition Chart supplied with the
equipment.
Symbol Definition
General Warning Sign
Forward/Reverse Trigger
(Action is in the direction of the arrow.)
Forward/Reverse Trigger
(Action is in the direction of the arrow.)
F/R 1 min/
4 min X 3
Duty Cycle
(See the Specifications section.)
Lock
Unlock
Direction of Rotation
Alignment Mark
USE ONLY
STRYKER
POWER
MODULE
Use only Stryker power module.
STERILIZE
WITH DOOR
FULLY OPEN
Sterilize with door fully open.
SSmall Diameter
LLarge Diameter
Run
Load
SERIAL Serial Number
Instructions
To Process the Equipment
WARNING: Upon initial receipt and before each
use, process the equipment as indicated in the care
instructions manual supplied with the equipment.
To Charge a Power Module
Fully charge the power module before first and every use.
NOTES:
▪ For charging instructions, see the instructions for use
supplied with the battery charger.
▪ For additional information, including safety information,
see the instructions for use supplied with the power
module.

8 www.stryker.com
EN 7305-001-700 Rev-A
To Install a Power Module
Sterile Assistant
1. Set the safety switch to the safe mode position.
2. Turn the latch to the unlock position and open the
door.
3. Place the sterile transfer shield over the open
compartment.
4. Present the compartment to the Circulating Assistant.
Circulating Assistant
WARNING: DO NOT contaminate the handpiece.
The transfer shield guards the sterile handpiece from
contamination during power module installation.
1. Hold the power module by the handle.
2. Insert the power module through the transfer shield
into the open compartment.
3. Push the handle down.

7305-001-700 Rev-A EN
www.stryker.com 9
WARNING: ALWAYS sterilize the contaminated
transfer shield before using it again.
4. Remove the contaminated transfer shield.
Sterile Assistant
WARNINGS:
▪ When closing the door, hold the door by the latch.
DO NOT touch the edges of the door or the internal
surface of the door that faces the power module.
▪ ALWAYS verify the door is securely closed to prevent
exposing the power module to the sterile field.
1. Holding the door by the latch, use the door to push the
power module handle down until it locks into position
against the power module.
2. Close the door and turn the latch to the lock position.
Verify the mark on the latch aligns with the lock
symbol and the door is securely closed.
NOTE: Although one power module is usually sufficient
for one operation, Stryker recommends preparing a
second handpiece with power module to ensure quick
intraoperative exchange of handpieces under sterile
conditions.
To Install an Attachment
1. Align the J-notch with the handpiece and insert the
attachment until it snaps securely into place.
2. Gently pull on the attachment to verify it is secure.

10 www.stryker.com
EN 7305-001-700 Rev-A
To Install and Remove a Cutting or
Fixation Tool
Wire and Pin Collets
1. Select the appropriate collet for the desired wire or pin
diameter.
NOTE: All collets have a pre-adjust knob with small and
large diameter settings.
Wire Collet (REF 7307-001-000)
Setting Wire or Pin Diameter
Small (S) 0.7 to 1.2 mm
Large (L) 1.3 to 1.8 mm
Pin Collet, Small (REF 7307-002-000)
Setting Wire or Pin Diameter
Small (S) 2.0 to 2.6 mm
Large (L) 2.7 to 3.2 mm
Pin Collet, Large (REF 7307-003-000)
Setting Wire or Pin Diameter
Small (S) 3.0 to 3.6 mm
Large (L) 3.7 to 4.2 mm
2. Pull and rotate the pre-adjust knob to align the
symbols for the desired wire or pin diameter. After
alignment, snap the knob back into place.
S
S
L
L
3. Insert the wire or pin through the front of the collet
or the back of the handpiece until the desired length
extends from the collet.
4. Pull the clamping lever back to grasp the wire or pin.
5. To remove the wire or pin, or to adjust the wire length,
release the clamping lever.

7305-001-700 Rev-A EN
www.stryker.com 11
Keyed Chucks
1. Use the chuck key to open the jaws.
2. Insert the tool into the center of the jaws.
3. Use the chuck key to close the jaws.
4. Visually inspect the tool to make sure it is centered in
the jaws.
5. Gently pull on the tool to verify it is secure.
6. To remove the tool, use the chuck key to open the
jaws again.
Keyless Chucks
1. Hold the attachment and manually rotate the chuck to
open the jaws.
2. Insert the tool into the center of the jaws.
WARNING: DO NOT operate the handpiece to close
the jaws on the cutting tool.
3. Hold the attachment and manually rotate the chuck to
close the jaws.
4. Visually inspect the tool to make sure it is centered in
the jaws.
5. Gently pull on the tool to verify it is secure.
6. To remove the tool, hold the attachment and manually
rotate the chuck to open the jaws again.

12 www.stryker.com
EN 7305-001-700 Rev-A
Drill and Reamer Attachments
1. Slide the retaining collar back.
2. Hold the retaining collar in position and insert the tool
into the attachment.
3. Release the retaining collar.
4. Gently pull on the tool to verify it is secure.
5. To remove the tool, slide the retaining collar back
again.
To Operate a Handpiece
WARNINGS:
▪ DO NOT open the handpiece housing during surgery
as the inside of the device is not sterile.
▪ ALWAYS follow the specified duty cycle to prevent the
equipment from overheating. See the Specifications
section.
▪ ALWAYS consult attachment and tool labeling for
product-specific duty cycles and instructions for use.
▪ DO NOT use this equipment in areas in which
flammable anesthetics or flammable agents are mixed
with air, oxygen, or nitrous oxide.
▪ Take special precautions regarding electromagnetic
compatibility (EMC) when using this equipment. Place
the equipment into service according to the EMC
information contained in this manual.
▪ Portable and mobile radio frequency (RF)
communications equipment can affect the function of
this equipment.
▪ This equipment should not be used adjacent to or
stacked with other equipment. If adjacent or stacked
use is necessary, ALWAYS verify normal operation in
the configuration in which it will be used.
▪ ALWAYS operate the equipment within the specified
environmental condition values:
Temperature
Limitation
Humidity
Limitation
Atmospheric
Pressure Limitation
1. Before operating the equipment, verify the following:
▪ You are using Stryker-approved equipment.
▪ The equipment is not damaged.
▪ The equipment is clean and sterile.
▪ You have properly assembled the equipment.
▪ You have installed a fully-charged power module.
NOTE: If you experience difficulty during operation,
contact your Stryker sales representative or call Stryker
customer service. See the Contact Information section.
Outside the US, contact your nearest Stryker subsidiary.

7305-001-700 Rev-A EN
www.stryker.com 13
2. Set the safety switch to the forward or forward/reverse
mode position.
NOTE: Set the safety switch back to the safe mode
position when the handpiece is idle or when passing the
handpiece to another person.
CAUTION: DO NOT apply excessive pressure or restrict
the motion of the cutting or fixation tool during operation.
An excessive load on the system may cause the power
module to temporarily shut down. If this happens, release
the trigger to resume operation or allow the power module
to cool for 20 to 40 minutes.
3. Pull the triggers to control the variable speed operation
of the handpiece.
NOTE: Typical power module run time is 5 minutes or
longer, depending on surgical procedure and technique.
To Remove an Attachment
1. Push the release lever down and pull the attachment
from the handpiece.
To Remove a Power Module
NOTE: Keep the power module as clean as possible
because it cannot be sterilized.
1. Wipe all debris from the external surfaces of the
handpiece.
2. Turn the latch to the unlock position and open the
door.
3. Use the handle to remove the power module from the
handpiece.

14 www.stryker.com
EN 7305-001-700 Rev-A
Specifications
Handpiece
Model: STRYKER SYSTEM G Rotary Drill
Catalog Number: 7305-001-000
Dimensions:
Length: 168.15 mm
Width: 83.82 mm
Height: 226.10 mm
Mass: 1.043 kg
Nominal Speed:
Drill: 825 revolutions per minute
Ream: 250 revolutions per minute
Mode of Operation: Non-continuous
Duty Cycle: 1 minute on/4 minutes off, 3 times
Rest Between Cycles: 4 hours
Applied Part: The handpiece, attachment, and cutting or fixation tool as defined by the manufacturer
Maximum Temperature
of Applied Part:
Less than 43 °C, as tested to the Product Safety Compliance standards at a maximum ambient
temperature of 30 °C.
Power Supply: Internally Powered
Ingress Protection (IP): IPX0
Equipment Type: Type BF Applied Part
European Conformity:
Attachments
Wire and Pin Collets
Model: STRYKER SYSTEM G
Wire Collet
STRYKER SYSTEM G
Pin Collet, Small
STRYKER SYSTEM G
Pin Collet, Large
Catalog Number: 7307-001-000 7307-002-000 7307-003-000
Dimensions:
Length: 88 mm 88 mm 88 mm
Diameter: 26 mm 26 mm 26 mm
Mass: 0.27 kg 0.27 kg 0.27 kg
Gear Ratio: 1:1 1:1 1:1
Ingress Protection (IP): IPX0
European Conformity:

7305-001-700 Rev-A EN
www.stryker.com 15
Keyed Chucks
Model: 1:1 1/4 inch (6.4 mm) Keyed
Chuck
High Torque 1/4 inch (6.35 mm)
Drill with Chuck 2:1 with Key
3.25:1 1/4 inch (6.4 mm)
Keyed Chuck
Catalog Number: 4103-131-000 4103-180-000 4103-231-000
Dimensions:
Length: 105.90 mm 111.25 mm 118.62 mm
Diameter: 28.60 mm 33.80 mm 28.60 mm
Mass: 0.313 kg 0.198 kg 0.182 kg
Gear Ratio: 1:1 2:1 3.25:1
Ingress Protection (IP): IPX0
European Conformity:
Keyless Chucks
Model: Keyless Chuck Adaptor Keyless Drill Attachment
Catalog Number: 4103-082-131 4103-133-000
Dimensions:
Length: 87.12 mm 126.50 mm
Diameter: 30.07 mm 31.95 mm
Mass: 0.185 kg 0.157 kg
Gear Ratio: 1:1 1:1
Ingress Protection (IP): IPX0
European Conformity:
Drill Attachments
Model: 1:1 AO Small Drill 1:1 Hudson 1:1 Hudson/Modified
Trinkle
1:1 Trinkle
Catalog Number: 4103-110-000 4103-113-000 4103-135-000 4103-160-000
Dimensions:
Length: 89.50 mm 84.33 mm 78.25 mm 79.85 mm
Diameter: 26.04 mm 26.04 mm 26.04 mm 26.04 mm
Mass: 0.185 kg 0.183 kg 0.157 kg 0.154 kg
Gear Ratio: 1:1 1:1 1:1 1:1
Ingress Protection (IP): IPX0
European Conformity:

16 www.stryker.com
EN 7305-001-700 Rev-A
Reamer Attachments
Model: 3.25:1 AO
Large Reamer
3.25:1 Hudson 3.25:1
Hudson/
Modified
Trinkle
3.25:1 Trinkle 4:1 Hudson 4:1 Hudson/
Modified
Trinkle
Catalog Number: 4103-210-000 4103-213-000 4103-235-000 4103-260-000 4103-413-000 4103-435-000
Dimensions:
Length: 95.45 mm 100.46 mm 94.00 mm 97.30 mm 100.46 mm 94.00 mm
Diameter: 27.95 mm 27.95 mm 27.95 mm 27.70 mm 32.40 mm 32.40 mm
Mass: 0.198 kg 0.256 kg 0.182 kg 0.180 kg 0.225 kg 0.208 kg
Gear Ratio: 3.25:1 3.25:1 3.25:1 3.25:1 4:1 4:1
Ingress Protection (IP): IPX0
European Conformity:
Transfer Shield
Model: STRYKER SYSTEM G Transfer Shield
Catalog Number: 7304-120-000
Dimensions:
Length: 150.9 mm
Width: 103.5 mm
Height: 37.0 mm
Mass: 77 g
European Conformity:
Product Safety Compliance
International Electrotechnical Commission (IEC)
IEC 60601-1 A1: R:2012 (3.1 Edition): Medical Electrical Equipment – Part 1: General Requirements for Basic Safety and
Essential Performance; IEC Corrigendum 1 (2006); IEC Corrigendum 2 (2007); Amendment 1 (2012)
IEC 60601-1-6: 2013: USABILITY – Medical electrical equipment – Part 1-6: General requirements for basic safety and
essential performance – Collateral standard: Usability – Edition 3.1 Consolidated Reprint.
IEC 62366: 2014: USABILITY – Medical devices – Application of usability engineering to medical devices - Edition 1.1
Consolidated Reprint.
IEC 60601-1-2: 2010: EMC (Version 3.0) – Medical electrical equipment – Part 1-2: General requirements for basic safety
and essential performance – Collateral standard: Electromagnetic compatibility – Requirements and tests – Edition 3.0
IEC 62133: 2012/12/06 Edition: 2.0: Secondary Cells and Batteries Containing Alkaline or other Non-Acid Electrolytes
– Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for use in Portable
Applications, Corrigendum 1:2013
European Committee for Electrotechnical Standardization (CENELEC)
EN 60601-1:2006/A1:2013 (3.1 Edition): Medical electrical equipment Part 1: General requirements for basic safety and
essential performance – Incorporates Amendment A12: 2014

7305-001-700 Rev-A EN
www.stryker.com 17
Electromagnetic Compatibility
Guidance and manufacturer’s declaration - electromagnetic emissions
The STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) is intended for use in the electromagnetic environment specified below. The customer or the
user of the STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) should assure that it is used in such an environment.
Emissions test Compliance Electromagnetic environment - guidance
RF emissions
CISPR 11
Group 1 The STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic
equipment.
RF emissions
CISPR 11
Class B The STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) is suitable for use in all establishments, including
domestic establishments and those directly connected to the public low-voltage power supply network that
supplies buildings used for domestic purposes.
Harmonic
emissions
IEC 61000-3-2
N/A
Voltage
fluctuations/flicker
emissions
IEC 61000-3-3
N/A
Guidance and manufacturer’s declaration - electromagnetic immunity
The STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) is intended for use in the electromagnetic environment specified below. The customer or the
user of the STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) should assure that it is used in such an environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic environment -
guidance
Electrostatic discharge (ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood, concrete or
ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30%.
Electrical fast transient/burst
IEC 61000-4-4
±2 kV for power supply lines
±1 kV for input/output lines
N/A
N/A
N/A
Surge
IEC 61000-4-5
±1 kV line(s) to line(s)
±2 kV line(s) to earth
N/A
N/A N/A
Voltage dips, short interruptions and
voltage variations on power supply
input lines
IEC 61000-4-11
<5% UT(>95% dip in UT)
for 0,5 cycle
40% UT(60% dip in UT)
for 5 cycles
70% UT(30% dip in UT)
for 25 cycles
<5% UT(>95% dip in UT)
for 5 seconds
N/A
N/A
N/A
N/A
N/A
Power frequency (50/
60 Hz) magnetic field
IEC 61000-4-8
3 A/m 3 A/m Power frequency magnetic fields
should be at levels characteristics
of a typical location in a typical
commercial or hospital environment.
NOTE: UTis the alternating current mains voltage prior to application of the test level.

18 www.stryker.com
EN 7305-001-700 Rev-A
Guidance and manufacturer’s declaration - electromagnetic immunity
The STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) is intended for use in the electromagnetic environment specified below. The customer or the
user of the STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) should assure that it is used in such an environment.
Immunity test IEC 60601 test
level Compliance level Electromagnetic environment - guidance
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to
80 MHz
N/A
Portable and mobile RF communications equipment should be used no closer to any
part of the STRYKER SYSTEM G Rotary Drill (REF 7305-001-000), including cables,
than the recommended separation distance calculated from the equation applicable to
the frequency of the transmitter.
Recommended separation distance:
150 kHz to 80 MHz
80 MHz to 800 MHz
800 MHz to 2.5 GHz
Where Pis the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer and dis the recommended separation
distance in meters (m). Field strengths from fixed RF transmitters, as determined by
an electromagnetic site survey,ashould be less than the compliance level in each
frequency range.bInterference may occur in the vicinity of equipment marked with the
following symbol:
(Non-ionizing electromagnetic radiation)
Radiated RF
IEC 61000-4-3
3 V/m
80 MHz to
2.5 GHz
[E1] = 3 V/m
NOTE 1: At 80 MHz and 800MHz the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and
people.
aField strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters,
an electromagnetic site survey should be considered. If the measured field strength in the location in which the STRYKER SYSTEM G Rotary Drill (REF
7305-001-000) is used exceeds the applicable RF compliance level above, the STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) should be observed
to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the STRYKER
SYSTEM G Rotary Drill (REF 7305-001-000).
bOver the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Recommended separation distances between portable and mobile RF communications equipment and the STRYKER SYSTEM G Rotary Drill (REF
7305-001-000)
The STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) is intended for use in the electromagnetic environment in which radiated RF disturbances
are controlled. The customer or the user of the STRYKER SYSTEM G Rotary Drill (REF 7305-001-000) can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the STRYKER SYSTEM G Rotary Drill
(REF 7305-001-000) as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output power of
transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
11. 2 1. 2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance din meters (m) can be estimated using the
equation applicable to the frequency of the transmitter, where Pis the maximum output power rating of the transmitter in watts (W) according to the
transmitter manufacturer.
NOTE 1: At 80 MHz and 800MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and
people.

2 www.stryker.com
ES 7305-001-700 Rev-A
Contenido
Introducción . . . . . . . . . . . . . . . . . . . . . 3
Destinatarios. . . . . . . . . . . . . . . . . . . 3
Convenciones . . . . . . . . . . . . . . . . . . 3
Información de contacto . . . . . . . . . . . . . 3
Propiedad intelectual . . . . . . . . . . . . . . . 3
Indicaciones de uso . . . . . . . . . . . . . . . . . 3
Contraindicaciones . . . . . . . . . . . . . . . . . . 3
Directivas de seguridad . . . . . . . . . . . . . . . . 3
Para uso con. . . . . . . . . . . . . . . . . . . . . 4
Componentes para la alimentación y el cuidado . . 4
Acoplamientos y herramientas de corte y fijación . 4
Introductores de alambre y clavos. . . . . . . 4
Portabrocas con llave . . . . . . . . . . . . 4
Portabrocas sin llave . . . . . . . . . . . . . 4
Acoplamientos de taladro. . . . . . . . . . . 4
Acoplamientos escariadores . . . . . . . . . 5
Características . . . . . . . . . . . . . . . . . . . . 5
Pieza de mano. . . . . . . . . . . . . . . . . . 5
Interruptor de seguridad . . . . . . . . . . . . . 6
Acoplamientos . . . . . . . . . . . . . . . . . . 6
Introductores de alambre y clavos. . . . . . . 6
Portabrocas con llave . . . . . . . . . . . . 6
Portabrocas sin llave . . . . . . . . . . . . . 6
Acoplamientos de taladro y escariador . . . . 7
Definiciones . . . . . . . . . . . . . . . . . . . . . 7
Instrucciones. . . . . . . . . . . . . . . . . . . . . 7
Para procesar el equipo . . . . . . . . . . . . . 7
Para cargar un módulo de alimentación . . . . . . 7
Para instalar un módulo de alimentación. . . . . . 8
Asistente estéril . . . . . . . . . . . . . . . 8
Asistente circulante . . . . . . . . . . . . . 8
Asistente estéril . . . . . . . . . . . . . . . 9
Para instalar un acoplamiento. . . . . . . . . . . 9
Para instalar y retirar una herramienta de
corte o fijación. . . . . . . . . . . . . . . . . .10
Introductores de alambre y clavos. . . . . . .10
Portabrocas con llave . . . . . . . . . . . 11
Portabrocas sin llave . . . . . . . . . . . . 11
Acoplamientos de taladro y escariador . . . .12
Para utilizar una pieza de mano. . . . . . . . . .12
Para retirar un acoplamiento . . . . . . . . . . .13
Para retirar un módulo de alimentación . . . . . .13
Especificaciones . . . . . . . . . . . . . . . . . . .14
Pieza de mano. . . . . . . . . . . . . . . . . .14
Acoplamientos . . . . . . . . . . . . . . . . . .14
Introductores de alambre y clavos. . . . . . .14
Portabrocas con llave . . . . . . . . . . . .15
Portabrocas sin llave . . . . . . . . . . . . .15
Acoplamientos de taladro. . . . . . . . . . .15
Acoplamientos escariadores . . . . . . . . .16
Escudo de transferencia . . . . . . . . . . . . .16
Homologaciones de seguridad de los productos . . . .16
Compatibilidad electromagnética . . . . . . . . . . .17