Stryker Surgistool 830 User manual

Medical
For parts or technical
assistance call
800 327 0770 (option 2)
Surgistool
Model 830
Operations/
Maintenance
Manual
Important
Information
File in your
maintenance
records

Table of Contents
Introduction
Specifications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning / Caution / Note Definition 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Pedal Operation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting The Back Rest 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting The Optional Wrist Rests 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventative Maintenance 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic System Troubleshooting 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Excess Air From The Hydraulic System 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Descent Rate Adjustment 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Hydraulic Fluid Level 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Hood Removal 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Valve Replacement 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjustment 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Reference Replacement Parts List 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly Drawings And Parts Lists
Seat to Base Assembly 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motorcycle Seat to Base Assembly 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Round & Obround Seat Assembly 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motorcycle Seat Assembly 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Assembly 16, 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Assembly 18−20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump Pedal Assembly 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Release Pedal Assembly 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Assembly 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Back Rest Assembly 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Wrist Rest Assembly 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Seat Riser Assembly 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limited Warranty
Obtaining Parts and Service 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Warranty Coverage 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Authorization 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freight Damage Claims 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction
2
INTRODUCTION
This manual is designed to assist you with the operation and maintenance of the Model 830 Surgistool II.
Read it thoroughly before using the equipment or beginning any maintenance on it.
SPECIFICATIONS
Maximum Weight Capacity 300 pounds
Upper/Lower Height Range 28.5 −21 inches
Upper/Lower Height Range w/2” Riser Kit 30.5 −23 Inches
Stryker reserves the right to change specifications without notice.
WARNING / CAUTION / NOTE DEFINITION
The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.
WARNING
Alerts the reader about a situation, which if not avoided, could result in death or serious injury. It may also
describe potential serious adverse reactions and safety hazards.
CAUTION
Alerts the reader of a potentially hazardous situation, which if not avoided, may result in minor or moderate
injury to the user or patient or damage to the equipment or other property. This includes special care neces-
sary for the safe and effective use of the device and the care necessary to avoid damage to a device that
may occur as a result of use or misuse.
NOTE
This provides special information to make maintenance easier or important instructions clearer.
Back to Table of Contents

Operation Guide
3
BASE PEDAL OPERATION
A
B
CSIDE VIEW
(A) Push down to set Surgistool brake. Lift up to release brake.
(B) Pump to raise Surgistool height.
(C) Depress to lower Surgistool height.
Back to Table of Contents

Operation Guide
4
ADJUSTING THE BACK REST
To adjust the height of the back rest, turn
knob (A) counterclockwise. Slide the
back rest up or down to the desired height.
Turn knob (A) clockwise and tighten until
the back rest is secure.
To move the back rest closer to the seat
or farther away from the seat, turn knob
(B) counterclockwise. Slide the back rest
in or out. Turn knob (B) clockwise until the
back rest is secure.
ADJUSTING THE OPTIONAL WRIST RESTS
To adjust the height of the optional wrist rests, turn
knob (A) counterclockwise. Raise or lower the wrist
rest to the desired height. Turn knob (A) clockwise un-
til the wrist rest is secure.
To pivot the wrist rest assembly, turn knob (B) counter-
clockwise. Pivot the wrist rest to the desired position.
Turn knob (B) clockwise until the wrist rest assembly
is secure.
A
B
A
B
Back to Table of Contents

Preventative Maintenance
5
CHECKLIST
All fasteners secure (reference all assembly prints)
Brake pedal engages with proper tension (page 9)
All casters secure and swivel properly
Wrist rests swivel and raise properly
No rips or cracks in seat, back rest or wrist rest covers
All adjustment knobs intact and functioning properly
No leaks at hydraulic connections
Hydraulic jack holding properly (page 7)
Hydraulic drop rate set properly (page 7)
Hydraulic oil level sufficient (page 8)
Lubricate where required
Serial No.
Completed By:_________________________________ Date:_____________
NOTE
The serial number label is located under the base frame (see page 11 for reference)
NOTE
Preventative maintenance should be performed at a minimum of annually. A preventative maintenance pro-
gram should be established for all Stryker Medical equipment. Preventative maintenance may need to be
performed more frequently based on the usage level of the product.
Back to Table of Contents

Cleaning
6
Hand wash all surfaces with warm water and mild detergent. Dry thoroughly. DO NOT STEAM CLEAN,
PRESSURE WASH, HOSE OFF OR ULTRASONICALLY CLEAN. Using these methods of cleaning is not
recommended and may void this product’s warranty.
In general, when used in those concentrations recommended by the manufacturer, either phenolic type or
quaternary type disinfectants can be used. Iodophor type disinfectants are not recommended for use be-
cause staining may result. The following products have been tested and have been found not to have a harm-
ful effect WHEN USED IN ACCORDANCE WITH MANUFACTURERS RECOMMENDED DILUTION.*
TRADE NAME DISINFECTANT
TYPE
MANUFACTURER
*MANUFACTURER’S
RECOMMENDED
DILUTION
A33 Quaternary Airwick (Professional Products Division) 2 ounces/gallon
A33 (dry) Quaternary Airwick (Professional Products Division) 1/2 ounce/gallon
Beaucoup Phenolic Huntington Laboratories 1 ounce/gallon
Blue Chip Quaternary S.C. Johnson 2 ounces/gallon
Elimstaph Quaternary Walter G. Legge 1 ounce/gallon
Franklin Phenomysan F2500 Phenolic Purex Corporation 1 1/4 ounce/gallon
Franklin Sentinel Quaternary Purex Corporation 2 ounces/gallon
Galahad Phenolic Puritan Churchill Chemical Company 1 ounce/gallon
Hi−To r Quaternary Huntington Laboratories 1/2 ounce/gallon
LPH Phenolic Vestal Laboratories 1/2 ounce/gallon
Matar Phenolic Huntington Laboratories 1/2 ounce/gallon
Omega Quaternary Airwick (Professional Products Division) 1/2 ounce/gallon
Quanto Quaternary Huntington Laboratories 1 ounce/gallon
Sanikleen Quaternary West Chemical Products 2 ounces/ gallon
Sanimaster II Quaternary Service Master 1 ounce/gallon
Vesphene Phenolic Vestal Laboratories 1 1/4 ounce/ gallon
Quaternary Germicidal Disinfectants, used as directed, and/or Chlorine Bleach products, typically 5.25% So-
dium Hypochlorite in dilutions ranging between 1 part bleach to 100 parts water, and 2 parts bleach
to 100 parts water are not considered mild detergents. These products are corrosive in nature and
may cause damage if used improperly. If these types of products are used to clean Stryker equipment,
measures must be taken to insure the unit is rinsed with clean water and thoroughly dried following cleaning.
Failure to properly rinse and dry the unit will leave a corrosive residue on the surface of the unit, possibly
causing premature corrosion of critical components.
NOTE
Failure to follow the above directions when using these types of cleaners may void this product’s warranty.
Back to Table of Contents

Service Information
7
HYDRAULIC SYSTEM TROUBLESHOOTING
PROBLEM/SYMPTOM SOLUTION
Jack will not raise to full height. Add hydraulic fluid (see below). Check for leaks.
Jack will not hold in raised position. Close the needle valve completely. If the jack holds,
replace valve (page 9). If the jack does not hold, re-
place jack.
Jack will not pump up. Remove excess air (vacuum) in system (see below).
If the jack still will not pump up, replace jack.
Contact Stryker technical support at 1−800−327−0770 for further assistance.
REMOVING EXCESS AIR (VACUUM) FROM THE HYDRAULIC SYSTEM
1. Pump the jack completely up and continue to pump the pedal after the jack reaches the top. This will
force the air through the system and the jack should now pump up.
JACK DESCENT RATE ADJUSTMENT
1. Pump the jack up to full height.
2. The descent rate butterfly valve is located on the manifold assembly. Reach under the base hood and
turn the valve clockwise to decrease the rate of descent. Turn it counterclockwise to increase the rate
of descent.
Back to Table of Contents

Service Information
8
CHECKING HYDRAULIC FLUID LEVEL
Required Tools:
5/32” Allen Wrench 3/8” Open End Wrench 3/4” Open End Wrench
Needle Nose Pliers
Procedure:
1. Using a 5/32” Allen wrench and a 3/8” open end wrench, remove the four button head cap screws and
four nylock nuts under the seat holding the seat assembly to the base.
2. Using needle nose pliers, remove the cotter pin under the base weldment plate.
3. Remove the base hood (see page 9).
4. Be sure there are no hydraulic leaks. If there are, the hydraulic jack must be replaced.
5. Lower the jack to the full down position.
6. Using a 3/4” open end wrench, slowly turn the fill plug located on the side of the reservoir counterclock-
wise to allow excess system pressure to vent. Remove the fill plug.
7. The hydraulic fluid should be visible at the bottom of the fill hole. If it is not, add Mobil Aero HFA hydraulic
fluid (Stryker part number 2020−70−475) until the fluid is visible at the bottom of the fill hole. Replace
the fill plug.
CAUTION
Use of other types of oil may damage hydraulic units.
8. Replace the base hood.
Back to Table of Contents

Service Information
9
BASE HOOD REMOVAL
Required Tools:
Standard Screwdriver 7/16” Open End Wrench
5/32” Allen Wrench Bungee Cords or String
Procedure:
1. Using a standard screwdriver, pop off the 3 black plastic caps covering the screws holding on the base
hood, being careful not to damage the caps.
2. Remove the nylock nuts, cap screws and washers holding the base hood to the base frame.
3. Lift up the hood and, using bungee cords or string, secure the hood to the bottom of the seat assembly.
4. After service is complete, lower the hood and reinstall the fasteners and protective caps.
HYDRAULIC VALVE REPLACEMENT
Required Tools:
Standard Screwdriver 3/4” Open End Wrench
Replacement Procedure:
1. Pump the jack fully up and raise the base hood (see above).
2. Turn butterfly valve (A) clockwise to close off the needle valve.
3. Remove the cap screw and washers holding the manifold as-
sembly (B) on the hydraulic jack.
4. Using a 3/4” open end wrench, remove the needle valve (C) from
the manifold assembly.
5. Install the new needle valve, reattach the manifold assembly,
open the butterfly valve and reattach the base hood.
6. Be sure the jack is operating properly before returning the Surgi-
stool to service.
BRAKE ADJUSTMENT
Required Tools:
1/2” Open End Wrench
Adjustment Procedure:
1. Loosen the top jam nut (A) on the brake foot assembly.
2. With your fingers, turn the brake shaft assembly (B)
clockwise to loosen the brake tension or counterclockwise
to tighten the brake tension.
3. Tighten the top jam nut when the desired tension is
achieved.
A
B
C
.032
A
B
.000
Back to Table of Contents

Quick Reference Replacement Parts List
10
PART NAME PART NUMBER
Brake Assembly 830−10−450. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Tip 830−10−451. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Jack Assembly w/Control 830−10−70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pad, Back Rest 830−20−20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pad, Wrist Rest 830−40−10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal, Brake 716−1−275. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal, Pump & Release 715−1−126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relief Valve, Hydraulic Jack 763−20−34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat, Motorcycle 763−201−29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat, Obround Pad 830−30−10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat, Tear Drop Pad 830−20−10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat Riser Kit, 2” 830−201−28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T−Handle, Female 24−45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T−Handle, Male 24−44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back to Table of Contents

Seat to Base Assembly, Round & Obround Seat
11
(ROUND SEAT SHOWN)
Assembly part numbers
830−20−101 (Round) &
830−30−101 (Obround)
(reference only)
Item Part No. Part Name Qty.
A(page 13) Seat Assembly 1
B16−28 Nylock Nut 4
C11−63 Flat Washer 4
D4−193 Hex Soc. But Hd. Cap Scr. 4
E(page 16 & 17) Hydraulic Base Assembly 1
F 830−90−4 Name Plate 1
J 921−1−252 Serial No. Label 1
Back to Table of Contents

Seat to Base Assembly, Motorcycle Seat
12
Assembly part number
830−201−20
(reference only)
Item Part No. Part Name Qty.
A(page 14) Motorcycle Seat Assembly 1
B16−28 Nylock Nut 4
C11−63 Flat Washer 4
D4−193 But. Hd. Cap Screw 4
E(page 16 & 17) Hydraulic Base Assembly 1
F 830−90−4 Name Plate 1
G 921−1−252 Serial No. Label 1
Back to Table of Contents

830−20−100/830−30−100 Seat Assembly, Round/Obround
13
S1
S2
Item Part No. Part Name Qty.
A 830−20−30 Seat Bracket Weldment 1
B 830−20−34 Backrest Support Bar 1
C 830−20−35 Clamp Weldment 1
D 830−20−38 Wear Strip 4
E 830−20−28 Female Hinge 1
F 830−20−26 Male Hinge and Pin 1
H 830−20−27 Flat Hd. Carriage Bolt 1
J24−45 T−Handle, Female 1
K24−44 T−Handle, Male 1
L12−12 Lockwasher 12
M4−193 Hex Soc. But. Hd. Cap Screw 12
N14−20 Nylon Washer 1
P11−4 Flat Washer 1
R 830−20−25 Hinge Spring 1
S1 830−30−10 Obround Seat Assembly 1
S2 830−20−10 Round Seat Assembly 1
T 830−20−20 Back Rest Assembly 1
W 830−91−3 Rotation Label 1
X38−278 Compression Spring 1
Back to Table of Contents

830−201−100 Motorcycle Seat Assembly
14
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 830−20−30 Seat Bracket Weldment 1 S 763−201−29 Seat & Mtg. Hardware 1
B 830−20−34 Backrest Support Bar 1 T 830−20−20 Back Rest Assembly 1
C 830−20−35 Clamp Weldment 1 W 830−91−3 Rotation Label 1
D 830−20−38 Wear Strip 4 X 38−278 Compression Spring 1
E 830−20−28 Female Hinge 1 Y 763−201−27 Adjustment Plate 2
F 830−20−26 Male Hinge and Pin 1 AA 11−2 Flat Washer 4
H 830−20−27 Flat Hd. Carriage Bolt 1 AB 3−76 Hex Hd. Cap Screw 2
J24−45 Female T−Handle 1 AC 763−201−28 U−Bracket 1
K24−44 Male T−Handle 1 AF 16−28 Nylock Nut 8
L12−12 Lockwasher 10 AH 763−201−24 Pivot Assembly 2
M4−193 But. Hd. Cap Screw 10 AJ 3−49 Hex Hd. Cap Screw 2
N14−20 Nylon Washer 1 AK 830−21−12 Seat Adapter Weldment 1
P11−4 Flat Washer 1 AL 11−179 Washer 2
R 830−20−25 Hinge Spring 1
Back to Table of Contents

Notes
15
Back to Table of Contents

830−10−100 Base Assembly
16
Back to Table of Contents

830−10−100 Base Assembly
17
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A 830−10−40 Base Weldment 1 AJ 4−20 Soc. Hd. Cap Screw 4
B(page 18) Jack & Control Assembly 1 AL 763−20−21 Hose Sleeve 3
C 830−10−50 Surgistool II Hood 1 AM 11−63 Flat Washer 11
D 830−10−51 Bellows 1 AN 16−28 Nylock Nut 7
E 830−10−55 Mounting Plate Weldment 1 AP (page 22) Release Pedal Assembly 1
F27−3 Cotter Pin 2 AR 830−10−24 Release Spring 1
H 830−10−180 Pump Link Weldment 1 AS 4−85 Soc. Hd. Cap Screw 2
J(page 21) Pump Pedal Assembly 1 AT 12−5 Lock Washer 2
K28−95 Retaining Ring 2 AW 11−16 Flat Washer 2
L11−4 Flat Washer 3 AY 38−15 Adjustable Clamp 2
M14−20 Plastic Flat Washer 3 AZ 763−20−13 Manifold Mounting Bracket1
N37−196 Protective Cap 3 BA 715−1−133 Spring Guide 1
P4−186 But. Hd. Cap Screw 3 BB 763−1−15 Jack Spring 1
R37−80 Retaining Washer 3 BC 763−1−16 Spring Guide 1
S 830−10−53 Caster 3 BD 390−1−67 Jack Washer 1
T11−13 Flat Washer 3 BE 37−55 Protective Cap 3
W16−64 Nylock Nut 3 BF 4−135 But. Hd. Cap Screw 3
Y 830−10−35 Brake Tip 1 BH 37−56 Retaining Washer 3
Z 830−10−34 Foot 1 BJ 946−1−60 Stryker Logo Label 2
AA 11−3 Flat Washer 1 BK 830−90−1 Rear Label 1
AB 14−21 Flat Washer 1 BL 830−90−2 Front Label 1
AD 15−12 Nut 1 BM 830−90−6 Pump Label 1
AF 763−1−33 Brake Nut 1 BN 830−90−7 Release Label 1
AH (page 23)* Brake Assembly 1
* Complete brake assembly (including items AH, Y & Z) is part number 830−10−450. Brake tip and foot assembly (includ-
ing items Y & Z) is part number 830−10−451.
Back to Table of Contents

830−10−70 Jack Assembly
18
Item Part No. Part Name Qty.
A48−13 Needle Valve 1
B48−146 90°Adjustable Elbow 1
C 390−2−147 L−Fitting 1
D 763−20−23 Return Line 1
E 763−20−34 Replacement Valve Ass’y 1
F(page 19) Jack Assembly 1
G 830−10−71 Pressure Line 1
Back to Table of Contents

Jack Assembly
19
Assembly part number 830−10−60 ( reference only)
Item Part No. Part Name Qty. Item Part No. Part Name Qty.
A45−904 Quad Ring 1 P 830−10−62 Actuator Cylinder 1
B 715−1−340 Machined Cap 1 R 390−2−139 Retaining Collar 2
C 390−1−243 Gasket 1 S 390−2−136 Pump Cylinder 1
D 390−2−137 Pump Cap 1 T 390−1−237 Pump Gasket 1
E(page 20) Jack Base Assembly 1 W 830−10−63 Actuator 1
F 390−2−147 ”L” Fitting 1 Y 715−1−331 Piston End 1
H 390−2−128 Packing 1 Z 926−20−161 Cup Packing 1
J 388−1−38 Plug 1 AA 926−20−162 Wear Ring 1
K 390−2−135 Pump Piston 1 AB 4−14 Soc. Hd. Cap Screw 1
L 830−10−61 Reservoir 1 AC 390−1−238 Actuator Gasket 1
M45−110 O−Ring 2 AD 45−14 O−Ring 1
N 390−1−244 Base Gasket 1
Back to Table of Contents