Stryker M-1 Series User manual

2018/08 B.2 6100-109-005 REV B www.stryker.com
International - EN | CS | DA | DE | ES | FI | FR
| NL | PL | PT | SV | NN | HU | IT
Operations Manual
M-1® Roll-In System
6100

sample text

2018/08 B.2 6100-109-005 REV B www.stryker.com
M-1® Roll-In System
6100
Operations Manual

sample text

www.stryker.com 6100-109-005 REV B
English
EN
Symbols
Refer to instruction manual/booklet
Operating instructions/Consult instructions for use
General warning
Caution
Catalogue number
Serial number
Lot (batch) code
For US Patents see www.stryker.com/patents
CE mark
EC REP
Manufacturer
Date of manufacture
Safe working load
Type BF applied part

sample text

www.stryker.com 6100-109-005 REV B 1-1
English
EN
Table of Contents
Warning/Caution/Note Definition ...............................................................................................................1-3
Summary of safety precautions.................................................................................................................1-4
Introduction...........................................................................................................................................1-6
Product description...........................................................................................................................1-6
Indications for use............................................................................................................................1-6
Expected service life.........................................................................................................................1-7
Contraindications .............................................................................................................................1-7
Specifications..................................................................................................................................1-7
Product illustration............................................................................................................................1-8
Contact information ..........................................................................................................................1-9
Serial number location .................................................................................................................... 1-10
Date of manufacture....................................................................................................................... 1-10
Setup................................................................................................................................................. 1-11
Installation.......................................................................................................................................... 1-12
Installing the cot fastener................................................................................................................. 1-12
Operation ........................................................................................................................................... 1-14
Operating guidelines....................................................................................................................... 1-14
Proper lifting techniques.................................................................................................................. 1-14
Transferring the patient to the cot...................................................................................................... 1-15
Rolling the cot with a patient............................................................................................................. 1-15
Changing the cot height................................................................................................................... 1-15
Loading the cot into a vehicle............................................................................................................ 1-16
Unloading the cot from a vehicle ....................................................................................................... 1-17
Positioning operators and helpers...................................................................................................... 1-17
Raising or lowering the backrest........................................................................................................ 1-18
Raising or lowering the siderails ........................................................................................................ 1-18
Raising or lowering the footrest ......................................................................................................... 1-18
Raising or lowering the optional knee gatch ......................................................................................... 1-19
Applying or releasing a wheel lock..................................................................................................... 1-19
Applying or releasing the caster Steer-Lock......................................................................................... 1-20
Connecting the litter to the base........................................................................................................ 1-21
Removing the litter from the base ...................................................................................................... 1-21
Changing cot height with the optional base head end retractable lifting handles .......................................... 1-22
Extending or retracting the retractable lifting handles............................................................................. 1-23
Securing the patient with the restraint straps........................................................................................ 1-23
Adjusting restraint straps ................................................................................................................. 1-24
Adding a restraint strap extension...................................................................................................... 1-25
Securing the patient with the Pedi-Mate® infant restraint system ............................................................. 1-25
Installing the defibrillator platform...................................................................................................... 1-26
Installing the head extension with pillow .............................................................................................. 1-28
Positioning the optional three-stage IV pole ......................................................................................... 1-28
Attaching an oxygen bottle to the oxygen bottle holder ........................................................................... 1-29
Accessories ........................................................................................................................................ 1-30

English
EN
1-2 6100-109-005 REV B www.stryker.com
Table of Contents
Cleaning............................................................................................................................................. 1-31
Disinfecting......................................................................................................................................... 1-32
Preventive maintenance ........................................................................................................................ 1-33
Regular inspection and adjustments................................................................................................... 1-33

English
EN
www.stryker.com 6100-109-005 REV B 1-3
Warning/Caution/Note Definition
The words WARNING,CAUTION, and NOTE carry special meanings and should be carefully reviewed.
WARNING
Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe
potential serious adverse reactions and safety hazards.
CAUTION
Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the
user or patient or damage to the product or other property. This includes special care necessary for the safe and
effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use or
misuse.
Note: Provides special information to make maintenance easier or important instructions clearer.

English
EN
1-4 6100-109-005 REV B www.stryker.com
Summary of safety precautions
Always read and strictly follow the warnings and cautions listed on this page. Service only by qualified personnel.
WARNING
• Always replace the cot fastener if it has been involved in an accident to avoid the risk of injury due to product
damage.
• Always make sure that all cots meet the installation specifications for the Stryker cot fastener system.
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in
this manual.
• Do not allow untrained assistants to assist in the operation of the product.
• Always follow proper hand placement on hand grips. Keep all hands clear of the red safety bar pivots when you
load or unload the cot or change cot height position.
• Do not ride on the base of the cot.
• Do not transport the cot sideways to avoid the risk of tipping. Always transport the cot in a lowered position, head
end or foot end first to minimize the risk of tipping.
• Always keep hands, fingers, and feet away from moving parts. Use caution when placing your hands and feet near
the base tubes while you raise or lower the cot.
• Do not leave a patient unattended. Hold the product while a patient is on the product.
• Do not apply a wheel lock when a patient is on the product or when you move the product to avoid the risk of tipping.
• Do not use siderails as a patient restraint device.
• Always transport the cot at a lower height to reduce the risk of a cot tip. If possible, obtain additional assistance or
take an alternate route.
• Always avoid high obstacles, such as curbing, steps, or rough terrain to avoid the risk of the product tipping over.
• Always lock the caster Steer-Lock knob and casters when you load or unload the cot from a vehicle or loading tray
system to avoid the risk of the product tipping.
• Always lock the caster Steer-Lock knob and casters when change the cot height to avoid the risk of the product
tipping.
• Always lock the base frame before you remove the loading wheels from the vehicle patient compartment floor or
loading tray system. An unlocked base frame will not support the cot and injury to the patient or operator could
result.
• Practice changing height positions and loading the cot until you fully understand the operation of the product.
• Always support the load of the patient, cot, and accessories after the weight is off of the ground.
• Do not apply a wheel lock when a patient is on the product or when you move the product to avoid the risk of tipping.
• Do not install or apply a wheel lock on a product with worn wheels that are less than 6 in. diameter.
• Always use all restraint straps to secure the patient on the cot. An unrestrained patient may fall from the cot.
• Do not attach restraint straps to the base tubes or cross tubes.
• Always locate the buckle away from obstructions or accessories on the cot to avoid the risk of accidental release of
Pedi-Mate®infant restraint system and injury to the infant.
• Always use any appropriate personal protective equipment while power washing to avoid inhaling contagion. Power
washing equipment may aerate contamination.
CAUTION
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in
this manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable
operation resulting in injury to patient or operator. Modifying the product also voids its warranty.

English
EN
www.stryker.com 6100-109-005 REV B 1-5
Summary of safety precautions
CAUTION (CONTINUED)
• The cot fastener system must be installed by qualified personnel. 1/4" steel backing plates (or equivalent) are
required beneath the mounting surface (ambulance floor or tray system) at all mounting points.
• Always clear any obstacles that may interfere and cause injury to the operator or patient before operating the
product.
• Do not apply the Steer-Lock and attempt to push the product sideways.
• Do not entangle the restraint straps in the base frame when you raise or lower the cot.
• Always secure the defibrillator platform to the product when you use the defibrillator platform.
• Always use and adjust the straps that are provided with the defibrillator platform to secure the defibrillator.
• Always change the installation location or adjust the straps for your specific defibrillator size or shape.
• Do not load the defibrillator platform above the safe working load of 30 lb (13.6 kg).
• Do not load the oxygen bottle holder above the safe working load of 15 lb (6.8 kg).
• Do not use two oxygen bottle holders at the same time.
• Do not steam clean or ultrasonically clean the product.
• Do not exceed 180° F (82° C) as the maximum water temperature.
• Do not exceed 1500 psi (130.5 bar) as the maximum water pressure. If you are using a hand held wand to wash the
product, keep the pressure nozzle at a minimum of 24 in. (61 cm) from the product.
• Always allow to air dry.
• Do not clean, disinfect, service, or perform maintenance while the product is in use.
• Always wipe the product with clean water and dry after cleaning. Some cleaning products are corrosive in nature
and may cause damage to the product. Failure to properly rinse and dry the product leaves a corrosive residue on
the surface of the product and may cause premature corrosion of critical components.
• Always use authorized parts to avoid the risk of product damage.

English
EN
1-6 6100-109-005 REV B www.stryker.com
Introduction
This manual assists you with the operation or maintenance of your Stryker product. Read this manual before operating
or maintaining this product. Set methods and procedures to educate and train your staff on the safe operation or
maintenance of this product.
CAUTION
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in
this manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable
operation resulting in injury to patient or operator. Modifying the product also voids its warranty.
Notes
• This manual is a permanent part of the product and should remain with the product even if the product is sold.
• Stryker continually seeks advancements in product design and quality. This manual contains the most current
product information available at the time of printing. There may be minor discrepancies between your product and
this manual. If you have any questions, contact Stryker Customer Service or Technical Support at 1-800-327-0770.
Product description
The Stryker Model 6100 M-1® Roll-In System is a manual ambulance cot. The platform on a wheeled frame supports
and transports a maximum weight of 500 lb (227 kg). The product is for use in pre-hospital and hospital environments.
The product is collapsible for use in emergency vehicles. The removable litter and patented Steer-Lock System™
provide enhanced maneuverability. To assist with patient transport, the product features:
• Lift handles at four corners
• Patient restraint straps
• Adjustable pneumatic backrest
• Optional accessories
For maximum patient comfort, you can select from one of three different litter positions, including:
• Shock
• Flat leg
• Optional Gatch
Indications for use
The Stryker Model 6100 M-1® Roll-In System is a non-powered, wheeled stretcher. The product supports and
transports the entire body of a traumatized, ambulatory or non-ambulatory human patient (including infants and adults).
In emergency or transport vehicles, the product:
• Supports patients in a supine (horizontal) or sitting position
• Facilitates the transportation of associated medical equipment (for example, oxygen bottles, or IV bags)
This product is for use in pre-hospital and hospital environments. You can use the product for emergency and non-
emergency applications. The maximum weight capacity is 500 lb (227 kg), which is the sum of the patient, mattress, and
accessory weight. Intended operators of the product include:
• Trained professionals
• Emergency medical service
• Medical care center personnel
• Medical first responders
Ambulance cots are for transportation purposes. They are not intended for extended stay or for use as hospital beds.
They are also not intended for use in devices that change air pressure, such as hyperbaric chambers.

English
EN
www.stryker.com 6100-109-005 REV B 1-7
Introduction
Expected service life
The Stryker Model 6100 M-1 Roll-In System has a five year expected service life under normal use conditions and with
appropriate periodic maintenance.
Contraindications
None known.
Specifications
For the Stryker Model 6100 M-1 Roll-In System base unit (6100-003-000), knee gatch litter (6100-031-000), and flat
foot section litter (6100-033-000).
Safe working load
Note: Safe working load indicates
the sum of the patient, mattress,
and accessory weight.
500 lb 227 kg
Backrest articulation/shock position ( 6100-031-000
and 6100-033-000)
0° to 75°
Length/width (6100-003-000) 77 in. / 21 in. 195.6 cm / 53.3 cm
Length/width (6100-031-000) 74.5 in. / 22.1 in. 189.2 cm / 56.1 cm
Length/width (6100-033-000) 74.8 in. / 22.1 in. 189.9 cm / 56.1 cm
Height1(6100-
003-000)
Position 1 14.4 in. 36.6 cm
Position 2 24.4 in. 62.0 cm
Position 3 30.0 in. 76.2 cm
Position 4 34.6 in. 87.9 cm
Position 5 37.6 in. 95.5 cm
Position 6 39.3 in. 99.8 cm
Position 7 13.0 in. 33.0 cm
Position 8 Not applicable Not applicable
Height1(6100-031-000 and 6100-033-000) 7.3 in. 18.5 cm
Weight2(6100-003-000) 77.7 lb 35.2 kg
Weight2(6100-031-000) 44.6 lb 20.2 kg
Weight2(6100-033-000) 40.2 lb 19.0 kg
Maximum weight capacity (6100-031-000 and 6100-
033-000)
500 lb 227 kg
Wheel diameter/ width (6100-031-000 and 6100-033-
000)
4.0 in. / 0.8 in. 10.2 cm / 2.0 cm
Handle extension (6100-031-000 and 6100-033-000) 7.75 in. 19.7 cm

English
EN
1-8 6100-109-005 REV B www.stryker.com
Introduction
Specifications (Continued)
Caster diameter/width (6100-003-000) 6 in. / 2 in. 15.2 cm / 5.1 cm
Shock position (6100-031-000) +17°
Knee gatch position (6100-031-000) 30°
Minimum operators required for loading/ unloading 1
Recommended fastener systems Model 638 1 Floor Mounted - Center Mount, Straight
Guide
Model 6373 Tray Mounted - Center Mount, DIN Guide
Model 6376 Floor Mounted - Center Mount, Straight
Guide - No side restraints
Recommended floor/tray height 27 in. - 31 in. 68.6 cm - 78.7 cm
1Height is measured from bottom of mattress at seat section to ground level.
2Standard base unit is weighed without optional accessories.
Stryker reserves the right to change specifications without notice.
The yellow and black color scheme is a proprietary trademark of Stryker Corporation.
Product illustration
A
BC
D
E
F
G
H
I
K
L
M
NP
J
N
M
G
F
F

English
EN
www.stryker.com 6100-109-005 REV B 1-9
Introduction
Product illustration (Continued)
R
T
U
V
W
X
YZ
R
R
V
W
Y
AA AB
A Base frame N Transport wheels
B Caster Steer-Lock knob P Wheel locks
C Foot end R Retractable litter lifting handles
DFoot end release handle (green) TKnee gatch release levers
EFoot end release handle (red) UKnee gatch lifting handle
FHand grips V Roller wheel
G Head end W Optional DIN retention pin
HHead end release handle (red) X Litter frame
ILitter release button (blue) Y Siderail release handle
J Litter retention brackets Z Perimeter bumper
KLoading wheel AA Backrest
LRelease button (green) AB Backrest adjustment release handle
MRetractable base lifting handle (optional)
Contact information
Contact Stryker Customer Service or Technical Support at: 1-800-327-0770.
Stryker Medical
3800 E. Centre Avenue
Portage, MI 49002
USA
To view your operations or maintenance manual online, see https://techweb.stryker.com/.
Have the serial number (A) of your Stryker product available when calling Stryker Customer Service or Technical
Support. Include the serial number in all written communication.

English
EN
1-10 6100-109-005 REV B www.stryker.com
Introduction
Serial number location
A
Figure 1-1: Serial number location
Date of manufacture
The year of manufacture is the first 2 digits of the serial number.

English
EN
www.stryker.com 6100-109-005 REV B 1-11
Setup
CAUTION
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in
this manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable
operation resulting in injury to the patient or operator. Modifying the product also voids its warranty.
Remove all shipping and packaging materials from the product prior to use.
Unpack the cartons and check all items for proper operation. Make sure that the product is working properly before it is
put into service.
Make sure that the patient compartment of the vehicle where you will be using the product has a:
• Smooth rear edge for product loading.
• Level floor that his large enough for the folded product and cot fastener system.
• Stryker Model 6373, 6376, or 6381 cot fastener system (not included)
• Floor or tray system loading height between 27.0 in. (68.6 cm) and 31.0 in. (78.7)
Note: Always remove loose items or debris from the patient compartment floor. Loose items or debris may interfere with
the cot rolling smoothly or the operation of the cot faster.
When necessary, modify the vehicle to fit the cot. Do not modify the cot.
This manual should be considered a permanent part of the product and should remain with the product even if the
product is subsequently sold.
Stryker continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your product
and this manual. If you have any questions, contact Stryker Customer Service or Technical Support at 1-800-327-0770.

English
EN
1-12 6100-109-005 REV B www.stryker.com
Installation
Installing the cot fastener
The Stryker Model 6373, 6376, and 6381 cot fastener systems are compatible only with cots that conform to the
installation specifications. Cots that meet these specifications include:
• Stryker Model 6100 M-1 Roll-In System
• Ferno-Washington Model X-21
WARNING
• Always replace the cot fastener if it has been involved in an accident to avoid the risk of injury due to product
damage.
• Always make sure that all cots meet the installation specifications for the Stryker cot fastener system.
CAUTION
The cot fastener system must be installed by qualified personnel. 1/4" steel backing plates (or equivalent) are required
beneath the mounting surface (ambulance floor or tray system) at all mounting points.
For more information about the Stryker cot fastener systems, see the Cot Fastener Operations and Maintenance
Manuals.
12000 model year or earlier. Stryker is not responsible for changes in specifications to other manufacturer’s cots.
Figure 1-2: Model 6376: View 2A
Figure 1-3: Model 6376: View 2B

English
EN
www.stryker.com 6100-109-005 REV B 1-13
Installation
Installing the cot fastener (Continued)
Figure 1-4: Model 6373: View 2C
Figure 1-5: Model 6373: View 2D

English
EN
1-14 6100-109-005 REV B www.stryker.com
Operation
Operating guidelines
WARNING
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in
this manual.
• Do not allow untrained assistants to assist in the operation of the product.
• Always follow proper hand placement on hand grips. Keep all hands clear of the red safety bar pivots when you
load or unload the cot or change cot height position.
• Do not ride on the base of the cot.
• Do not transport the cot sideways to avoid the risk of tipping. Always transport the cot in a lowered position, head
end or foot end first to minimize the risk of tipping.
• Always keep hands, fingers, and feet away from moving parts. Use caution when placing your hands and feet near
the base tubes while you raise or lower the cot.
CAUTION
Always clear any obstacles that may interfere and cause injury to the operator or patient before operating the product.
• Operate the product only as described in this manual.
• Read all labels and instructions on the product before use.
• Practice changing height positions and loading the cot until you fully understand the operation of the product.
• Always load or unload an occupied cot with a minimum of two trained operators. Two operators must be present
when a cot is occupied. Stryker recommends that both operators are at the foot end to reduce the load on each
operator. One or two operators can lift from the foot end of the cot.
• Do not adjust, roll, or load the cot into a vehicle without advising the patient. Stay with the patient and control the
product at all times.
• You can transport the cot in any position. Stryker recommends that the operators transport the patient in the lowest
comfortable position to maneuver the cot.
• Only use the wheel locks during patient transfer or without a patient on the product.
• Do not apply a wheel lock when an occupant is on the product or when moving the product to avoid the risk of
tipping.
• Always use all restraint straps to secure the patient on the product. An unrestrained patient may fall from the
product.
• Use properly trained helpers to control the cot, when necessary.
Proper lifting techniques
When you lift the product and occupant, follow these proper lifting techniques to avoid the risk of injury:
• Keep your hands close to your body
• Keep your back straight
• Coordinate all movement with your partner
• Lift with your legs
• Avoid twisting