Style selections 2290FM-18-251 User manual

1
ITEM #1051239; 32255009
ROLLING ELECTRIC
FIREPLACE
MODEL #2290FM-18-251
Français p. 13
ATTACH YOUR RECEIPT HERE
STYLE SELECTIONS and logo design are trademarks or
registered trademarks of LF, LLC. All rights reserved.
Serial Number _______________ Purchase Date _______________
Questions, problems, missing parts? Before returning to your retailer, call our customer service
department at 877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Sunday.
You could also contact us at [email protected] or visit www.lowespartsplus.com.
AS21016

2
TABLE OF CONTENTS
Package Contents ............................................................................................................................... 3
Hardware Contents.............................................................................................................................. 3
Safety Information ............................................................................................................................... 4
Preparation.......................................................................................................................................... 6
Assembly Instructions.......................................................................................................................... 6
Operating Instructions ......................................................................................................................... 7
Care And Maintenance........................................................................................................................ 9
Troubleshooting................................................................................................................................. 10
One-Year Limited Warranty ................................................................................................................11
Replacement Parts List ..................................................................................................................... 12

3
PACKAGE CONTENTS
O
A
QP
PART DESCRIPTION QUANTITY
A Mantel 1
O Insert 1
P Remote Control 1
Q Battery 2
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
AA
PART DESCRIPTION QUANTITY
AA Touch-up Pen 1

4
SAFETY INFORMATION
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the
following:
DANGER
• Read all instructions before using this heater.
• If the information in this manual is not followed
exactly, an electric shock or fire may result causing
property damage, personal injury or loss of life.
WARNING
• This appliance is hot when in use. To avoid burns,
DO NOT let bare skin touch hot surfaces. Keep
combustible material, such as furniture, pillows,
bedding, papers, clothes and curtains at least 3
feet from this appliance and keep them away from
the sides and rear.
• Extreme caution is necessary when any heater
is used by or near children or individuals with
disabilities and whenever the fireplace is left
operating and unattended.
• DO NOT run cord under carpeting. DO NOT cover
cord with throw rugs, runners, or similar coverings.
DO NOT route cord under furniture or appliances.
Arrange cord away from traffic areas and where it
will not be tripped over.
• DO NOT insert or allow foreign objects to enter
any ventilation or exhaust opening as this may
cause an electric shock or fire, or damage the
appliance.
• This appliance has hot and arcing or sparking
parts inside. DO NOT use it in areas where
gasoline, paint or flammable vapors or liquids are
used or stored. This fireplace should not be used
as a drying rack for clothing. Christmas stockings
or decorations should not be hung in the area of it.
• Use this appliance only as described in the
manual. Any other use is NOT recommended by
the manufacturer and may cause fire, electric
shock or injury to persons.
CAUTION
• If possible, ALWAYS unplug this appliance when
not in use.
• DO NOT operate any heater with a damaged
cord or plug or after the heater malfunctions. DO
NOT operate any heater if it has been dropped
or damaged in any manner. Disconnect power
at service panel and have heater inspected by a
reputable electrician before reusing.
• Any repairs to this fireplace should be carried out
by a qualified service person.
• Under no circumstances should this fireplace be
modified. Parts having to be removed for servicing
must be replaced prior to operating this fireplace
again.
• DO NOT use outdoors.
• This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. NEVER
place heater where it may fall into a bathtub or
other water container.
• To disconnect this appliance, turn controls to the
off position, then remove plug from outlet.
• ONLY connect to properly grounded outlets.
• This appliance, when installed, must be electrically
grounded in accordance with local codes, with the
current CSA C22.1 Canadian Electrical Code or
follow U.S.A. Installations, follow local codes and
the National Electrical Code, ANSI/NFPA N0.70.
• To prevent a possible fire, DO NOT block air
intakes or exhaust in any manner. DO NOT use
on soft surfaces, like a bed, where opening may
become blocked.
• The heaters MUST NOT be located immediately
below a socket-outlet.
• ALWAYS plug heaters directly into a wall outlet /
receptacle. NEVER use with an extension cord or
re-loadable power tap (outlet / power strip).
• DO NOT slide insert on top of wood to avoid
scratching wood surface.
• DO NOT place any object on top of the insert or
block the air intakes/vents as this can cause the
unit to overheat and could cause a fire.

5
SAFETY INFORMATION (CONTINUED)
Electrical Connection
• A 15-Amp, 120-volt, 60 Hz circuit with a properly
grounded outlet is required. Preferably, the
fireplace will be on a dedicated circuit as other
appliances on the same circuit may cause the
circuit breaker to trip or the fuse to blow when the
heater is in operation. The unit comes standard
with 6-ft. three-wire cord, exiting from the rear of
the fireplace. DO NOT exceed the current rating of
the current tap.
Grounding Instructions
• This heater is for use on 120 volt. The cord has a
plug as shown below. See illustration or grounding
instruction. An adapter as shown at C is available
for connecting three-blade grounding type plugs
to two-slot receptacles. The green grounding plug
extending from the adapter must be connected to
a permanent ground such as a properly grounded
outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
A B C
Grounding Pin
Grounding Means
Metal
Screw
Cover of
Grounding
Box
Adapter
SAVE THESE INSTRUCTIONS

6
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
ASSEMBLY INSTRUCTIONS
Note: Pull up to open the flip up door.

7
OPERATING INSTRUCTIONS
Control Panel Remote Control
AAA 1.5V
AAA 1.5V
To use the remote control, first insert two
AAA batteries (included) into the remote
control. Ensure the polarities of the
batteries match the inside of the battery
compartment.
Note: When the indicator lights are all on, there is no operation for 10 seconds, the machine enters the
blanking state, and the indicator lights are all off. Enter the blanking state. When any button is pressed again,
all the indicators will light up and display the state value or letter before blanking. If the button responds again
within 10 seconds, press the button to adjust the displayed corresponding function, 10 seconds blanking time
is reset.
Power Function
• Press the POWER ICON to turn the main power to the unit ON or OFF.
• The POWER ICON on the control panel and the remote control has the same highest priority
(compared to HEATER, FLAME).
• The POWER ICON has a memory function, its function is to memorize the current state (except
the timing function) and close all the functions that have been turned on. Press this button again to
restore the state set before turning off.
• If you use this key to turn off all the functions of the machine, you cannot turn on the machine by
pressing other keys.
• The digital tube displays the flame position by default when it is powered on: L4 high light.
Flame & Ember Bed Brightness Function
• Press the FLAME BRIGHTNESS ICON to adjust the flame and ember bed brightness at the same
time.
• Press the FLAME BRIGHTNESS ICON again to scroll down through the flame brightness settings:
L4-L3-L2-L1-OFF. In the OFF state, the flame ember bed goes out.
• The digital tube will display the corresponding value according to the user's setting, OFF does not
display.
• Brightness level: L4 (high light), L3 (medium light), L2 (low light), L1 (slightly light).
Heater Function
• Press HEATER ICON to turn on and off the heating function.
• When the HEATER is turned on and the temperature is displayed, press and hold the HEATER
ICON for 5 seconds to enter the temperature adjustment mode for temperature adjustment.
Note: This option is only available if using the control panel.
• Press and hold the POWER ICON for 5 seconds, the temperature unit will flash 3 times and then
you can switch between Fahrenheit and Celsius.
Note: This option is only available if using the control panel.

8
OPERATING INSTRUCTIONS (CONTINUED)
• Press and hold the HEATER ICON for 10 seconds to engage the heater function. Press and
hold the HEATER ICON for 10 seconds again to disengage the heater function. (See HEATER
OVERRIDE section below for more details).
Note: This option is only available if using the control panel.
• If the flame and ember bed brightness are off before the heating function is turned on, after turning
on the heat, the flame and ember bed brightness is slightly light on by default.
• When the heating function is turned on for the first time, the temperature unit is set to 82°F by
default.
Increase/Decrease Button
Note: This option is only available if using the remote control.
• Press the INCREASE/DECREASE button to adjust the heater’s thermostat setting.
• Press the INCREASE/DECREASE button again to scroll up through the pre-set temperature
settings: The thermostat setting range is 64°F (18°C) to 82ºF (27°C), ON. (FA is a fan function. The
fan works normally, but the heater does not work.)
• Set the temperature to “ON” to have the heater run continually.
Timer Function
• Press the TIMER ICON to set the countdown for the unit’s main power.
• Press the TIMER ICON again to scroll through the timer settings, which are: 1H, 2H, 3H, 4H, 5H,
6H, 7H, 8H, OFF. (The default is 8H.).
• After setting the timer time, if you press POWER ICON, it will turn off the timer and enter standby.
HEATER OVERRIDE
The power to the heater can be disengaged to prevent the heater from being accidentally or unintentionally
powering on. This feature is primarily added to help prevent children from powering on the heater when it is
not desired.
• To enable the heater override function press and hold HEATER ICON for 10 seconds. The flame and ember
bed brightness will flash 6 times quickly, indicating that the lock is successful. When the heat is locked,
press the HEATER ICON, the ember bed brightness will flash 6 times to remind the user that the heat is
locked.
• To unlock the heater function, press and hold the HEATER ICON for 10 seconds. The flame and ember bed
brightness will flash 6 times quickly. The heater function is now engaged. By pressing the HEATER ICON
again you will be able to adjust the heat temperature to your desired temperature.
MEMORY FUNCTION
This unit has a memory function that allows you to turn off the MAIN POWER and retains all the other function
settings (excluding the TIMER function).
• When the unit’s main power is OFF, press the POWER ICON once on the insert control panel or on the
remote control to power the unit ON and “wake up” the individual function at the last setting. Press the icon
again to adjust it and press the main POWER ICON on the insert or on the remote control to turn the unit
OFF and save the new setting into memory.
• When the unit is powered ON, the LED readout will show the saved temperature setting. If a temperature
setting was not saved, it will show the flame brightness setting saved in memory. If neither one has a setting
saved to memory, then only the ember bed will glow (as a power light indicator).
• Another way to reset the memory is to unplug the unit from the wall.

9
CARE AND MAINTENANCE
• Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool whenever you are
cleaning the heater or fireplace.
• Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household
cleaners as these products will damage the metal trim.
• The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life
and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/
output vents are recommended.
• When the heater is not in use, the power cord should be stored properly to avoid contact with hot or sharp
objects.
• Any other servicing should be performed by an authorized service representative.
• Tips for using touch-up pen (AA): For scratches, stroke in direction of scratch. For worn areas, stroke in the
direction of wood grain. Rub excess colorant promptly with a soft cloth.
Replacing the Remote-Control Batteries
When the remote control (P) stops operating or its range
seems reduced, it is time to replace the batteries. Note:
The batteries should be removed if the product is to be left
unused for a long time.
1. The battery compartment is located on the back of the
remote control (P).
2. Remove battery cover from the back of remote control (P)
and remove the old batteries.
3. Insert 2pcs AAA batteries, ensuring the polarities of the
battery match the inside of the battery compartment.
4. Re-insert the battery door.
AAA 1.5V
AAA 1.5V
P
Note: Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc), or rechargeable (nicad, nimh, etc.) batteries.
Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from the
product.
Harmful if swallowed.
Disposal of Used Battery
A battery may contain hazardous substances that could be endangering the environment and human health.
• This symbol marked on the battery and/or packaging indicates that used
battery shall not be treated as municipal waste. Instead it shall be left at
the appropriate collection point for recycling.
• By ensuring the used battery is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health. The recycling of materials will help to conserve natural resources.
• Do not dispose of batteries in fire. Batteries may explode or leak.
For more information about collection and recycling of used batteries,
please contact your local municipality, your waste disposal service or the
point-of-sale where you purchased this battery.

10
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Error E1 displayed on
control panel.
The overheat sensor has
been engaged.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding the
heater. Until the problem is solved, the error will only appear
when the heater button is pressed.
Error E2 displayed on
control panel.
The thermostat sensor
is broken or not working
correctly.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding the
heater. Until the problem is solved, the error will only appear
when the heater button is pressed.
Error E3 displayed on
control panel.
The heater is not working. Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding the
heater. Until the problem is solved, the error will only appear
when the heater button is pressed.
No power; logs do not
glow.
The unit does not have
power.
Check that the power cord is securely plugged into a
standard 120V outlet. Then check to make sure the unit is
powered on.
No flame effect but
logs are glowing.
The flame effect is
powered off.
Push the flame brightness button until desired level is
achieved.
Heater and blower
do not power on but
rest of functions are
working.
Heater override function is
engaged
To unlock the heater, simply press and hold the temperature
button for 10 seconds (See page 8 Heater Override Section
for more details).
Power cord gets warm
to the touch.
Normal operation. This is normal for a heater appliance as it requires more
current to operate. Check the connections of the appliance
cord and the outlet. Make sure the plug fits tightly into the
outlet. During use, check the plug and outlet frequently to
determine if it is HOT; if so, discontinue use of the appliance
and consult with a qualified electrician to check or change
the overheating outlet(s).
Remote control does
not work.
Weak or failing batteries. Replace with 2 AAA batteries (See page 9 for more
information.)
Remote control signal
is weak and only
works sometimes.
Pressing the buttons too
quickly.
Press the buttons slowly and steadily to ensure the
transmitter recognizes the request.
Using the remote control
too far away or at an off
angle.
Move closer to the insert; the remote control will only work
within a distance of 20 feet and 45 degrees to either side
from the front of the fireplace insert.
Fan motor continues
to blow after unit is
powered off.
Normal operation. This is a standard feature; the blower runs for an additional
time to cool off heater tubes.