Summer Central Station User manual

Central Station
Safety Gate
OWNER’S MANUAL
Please read the following instructions carefully.
Keep this instruction manual and save for future reference.
For technical support, contact us at1-401-671-6551
or www.summerinfant.com/contact
Tools required: Phillips head screwdriver,
measuring tape (not included),and wrench (included).
For use with children from 6 - 24 months.
Keep small parts away from children.
Adult assembly required.
Fits openings from 28.5 in.- 52 in.wide.

components
hardware:
K
x4 x4
L
2
M N
OP
x4 x4
x1x4
Gate Door
Gate Frame
A
B
Large Extension Frame
Medium Extension Frame
C
D
Small Extension Frame
Upper Latch
Handle/Release Button
Top Latch
E
Tension Bolts with Tension Nuts (4)
M
Adhesive Mounting Pads (4)
N
F
G
Wall Cups (4)
O
P
Wall Anchors (4)
Screws (4)
Wrench (4)
I
L
Extension Pins (6)
K
Door Stop
J
Lower Latch
H
C ED
J
Children have died or been seriously injured when gates are not securely installed.
• ALWAYS install and use gate as directed using all required parts.
• Install according to manufacturer’s instructions.
• Stop using when a child can climb over or dislodge the gate.
• Use only with the locking/latching mechanism securely engaged.
• To prevent falls, never use at top of stairs without wall mounting cups and door stopper.
• You MUST install wall cups to keep gate in place. Without wall cups, child can push out and escape.
• NEVER use a gate to keep child away from pool.
• NEVER leave child unattended.
• ALWAYS close and lock the gate behind you.
• This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.
• Do not use if any components are missing or damaged.
• Adult assembly required. Exercise care when unpacking and assembling product.
CAUTION: KEEP SMALL PARTS OUT OF CHILD’S REACH.
WARNING
NOTE: Gate will appear as
though door is o-center
when taken out of the
package until you mount it
into the doorframe and
tighten the bolts according
to the instructions.
BA
H
I
FG

3
gate configurations (choosewhich best fits your scenario)
1 2
4
(28.5 in - 31.25 in.)
without extension frames
(32 in. - 35.25 in.)
with small extension frame
(34.75 in. - 38 in.)
with medium extension frame
NEVER install three extension frames on the
same side of the gate. If using more than one
extension frame, use one on each side of the gate.
!
Note: This instruction book illustrates installation of gate conguration .
If choosing gate conguration , skip ahead to Step 1, page 6. Otherwise,
follow Step #1, page 5, using the appropriate extension frames that
best t your scenario.
Important: Gate includes a door stop (component ) which prevents the gate
from swinging open in one direction. When installing the gate at the top of stairs,
be sure that the door stop is on the stairway side of the gate so the door cannot
open over the stairs. While the door stop comes assembled on the gate, it can be
removed and installed on either side of the gate frame.
When gate is not used at top of stairs, door stop may be removed to allow gate
door to open in either direction.
I
5
3
6
78
(44.75 in. - 48 in.)
with medium and large extension frames
(48.75 in. - 52 in.)
with small, medium and large extension frames
(38 in. - 41.25 in.)
with large extension frame
(38.75 in. - 42 in.)
with small and medium extension frames
(42 in. - 45.25 in.)
with small and large extension frames
WARNING
sm
lg
lg sm med
med
!
sm med sm lg
med lg
1
8
Measure the width of the opening where you intend to
install the gate. Refer to the following illustrations to
determine the correct installation conguration.
Baseboard molding may change which conguration is
appropriate.

4
assembly
Connect the extension frames to the gate frame
by sliding the pins into the adjacent holes.

5
1
assembly (continued)
Slide tension bolts
into upper and lower holes
on both sides of
the gate assembly.
x 4
K
2

6
The distance between the gate and the wall
should never exceed 2.75 in.
IMPORTANT
Stand the gate in the
center of the opening.
!
Make sure door stop is facing desired direction.
For top of stair use, door stop must be on stair
side of gate. Gate door must open away from
stairs.
AB
1
Make sure the bottom of
the gate is completely flat
to the floor.
Slide tension bolts out
until they touch the
door frame or wall.
Checking the gate fit in the door frame

7
Use the tension nuts
to tighten both of the
bottom tension bolts.
Use the tension nuts
to tighten both of the
top tension bolts.
8
tighten!
tighten!
tighten!
tighten!
2
3
Checking the gate fit in the door frame (cont.)
Proceed to Wall Cup Installation section once check is complete.

8
With a pencil, trace
the entire outline
of each tension bolt
directly onto the wall.
x 4
Loosen the
lower and upper
tension nuts and
remove gate.
loosen!
loosen!
x 2
x 2
Door stop must be
on stair side of gate.
Gate door must open
away from stairs.
!
At the top of the
landing, position the
gate a minimum of
3-6 inches (8-15cm)
away from the top
step.
IMPORTANT
1
2
You MUST install wall cups to keep gate in place.
Without wall cups, child can push out and escape.
WARNING
wall cup installation

9
Mark drill holes
with a pencil
through the center
of each wall cup.
Mark drill holes
with a pencil
through the center
of each wall cup.
x4
Place a wall cup over
the center of each circular
outline on the wall.
Place a wall cup over
the center of each circular
outline on the wall.
3
wall cup installation (cont.)

wall cup/top ofstairs installation (continued)
10
x 4
1
st
Drill a 7/32''pilot hole
into each of the 4
center marks.
Drill a 7/32'' pilot hole
into each of the 4
center marks.
2
nd
Insert wall anchors
into pilot holes.
Insert wall anchors
into pilot holes.
N
4

Attach one pad to
the back of each
wall cup.
peel
peel
2
nd
3
rd
Remove backing
from one side of each
adhesive mounting pad.
Remove
backing.
1
st
5
Align the wall cups
so the center hole
is placed directly
over the wall anchor.
Stick the wall cups
to the wall.
!
Make sure
all wall cups
are facing up.
Make sure
all wall cups
are facing up.
wall cup/top of stairs installation (continued)
press
press
press
press
6
11
x 4
x 4
M
L

x4
Screw wall cups
into wall.
x 4
wall cup/top of stairs installation (continued)
7
8
12
O
Repeat "installation"
steps on page 5.
The 4 tension bolts
will rest within
each wall cup.
x 4

wall cup/top ofstairs installation(continued)
13
P
Tighten all 4
tension nuts
with the provided
wrench.
x 4
FINISHED!
Adjust the top tension nuts
to make sure the
release button tab resides
in the latch handle recess.
installation

testing the installation
14
testing the installation
operation
to unlock gate: hold-open feature:
Slide release buton.
Lift gate open.
To activate, open gate door
at least 90º in
either direction.
Close the gate.
Make sure the
upper and lower
latches lock
securely.
push!
push!
Push the gate and
extension frames
to check
stability.
1
st
2
nd
2
nd
1
st

15
troubleshooting
maintenance
If the gate does not close properly:
1. Gate is not properly aligned in the
door frame.
Solution: Loosen all four tension bolts
and reposition gate so that it matches
the “correct” image. Re-tighten
tension bolts.
2. Pressure of tension bolts needs
to be adjusted.
Solution: Loosen or tighten the upper tension
bolts. Ensure the upper latch engages securely
when the gate swings closed, and that it can be
released properly when the release button is
pushed back.
replacement hardware kit #33170-50
• Regularly check tension bolts to make sure the gate is securely in place.
• Do not use the gate if any components are damaged or missing.
• Surface-clean with a damp cloth or sponge, using mild detergent and warm water.
correct!
incorrect!
To order a replacement hardware kit, contact our Consumer Relations Team at 1-401-671-6551
or www.summerinfant.com/contact.

Colors and styles may vary.
MADE IN CHINA.
D0000000670 2/20
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket,RI 02895 USA
1-401-671-6551
© 2020 Summer Infant (USA),Inc.
We're here to help!
If you have any questions or need assistance,
contact our Consumer Relations Team at
1-401-671-6551 or www.summerinfant.com/contact