Summers SW4350 User manual

Operator’s Manual
®
SUMMERS MANUFACTURING CO., INC.
WEB SITE: www.summersmfg.com
DEVILS LAKE, NORTH DAKOTA 58301 [phone]
IMPORTANT
THE OPERATOR IS RESPONSIBLE
FOR ADJUSTING THE MACHINE SINCE
MACHINE DOES NOT COME “FIELD
READY” FROM FACTORY.
CAUTION
READ & UNDERSTAND OPERATOR’S
MANUAL BEFORE USING MACHINE.
See www.summersmfg.com for latest version of all Summers Operator’s Manuals.
SW4350
(Superweeder)
8Z1101D © Summers Mfg. Co., Inc. 2019 Printed in USA
8Z1101D - SW4350 (Superweeder)
8Z1101D - SW4350 (Superweeder)

Page 2 © Summers Mfg. Co., Inc. 2019 8Z1101D
TABLE OF CONTENTS
FOREWARD..................................................................................................................................... 3
Preface .......................................................................................................................................3
Disclaimer ...................................................................................................................................3
Contact Information ....................................................................................................................3
Owner Registration Information ..................................................................................................3
WARRANTY ..................................................................................................................................... 4
SAFETY............................................................................................................................................ 5
Safety Information.......................................................................................................................5
General Safety Practices ............................................................................................................5
Safety During Transportation ......................................................................................................5
Safety Decals.........................................................................................................................6-10
Safety Light Operation ..............................................................................................................10
General Maintenance Safety Practices .................................................................................... 11
OPERATION................................................................................................................................... 12
Connecting to Implement..........................................................................................................13
Lift Arm Adjustment...................................................................................................................14
Unhitching................................................................................................................................. 11
MAINTENANCE & SPECIFICATIONS ........................................................................................... 13
Daily & Periodic Maintenance...................................................................................................13
Troubleshooting ........................................................................................................................13
PARTS LIST ................................................................................................................................... 14
Hitch...................................................................................................................................14 - 15
Drawbars ...........................................................................................................................16 - 17
Hydralic Depth Adjust ........................................................................................................18 - 19
Weeder Arms .....................................................................................................................20 - 21
5 ft. Harrow Sections .........................................................................................................22 - 23
Hitch Hydraulics.................................................................................................................24 - 25
40’ - 70’ S-Tine Hydraulics .................................................................................................26 - 27
30’ S-Tine Hydraulics.........................................................................................................28 - 29
Light Kit..............................................................................................................................30 - 31
Depth Control Hydraulics..........................................................................................................32
Part Numbers with Descriptions ........................................................................................33 - 36

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 3
FORWARD
Preface
This manual is intended for use with Superweeder for Summers® Manufacturing Company, Inc.
This book is composed of these basic sections: Safety, Operation & Maintenance, Troubleshooting
and Parts. The safety section provides complete instructions for the proper safe operation of a Sum-
mers Mfg. product. The Operation & Maintenance section provides information for the proper opera-
tion and maintenance. A complete parts breakdown is provided in the Parts section.
Parts are referenced in each drawing with the Summers Manufacturing part number. Use this part
number when ordering replacement parts from your Summers dealer. See the back section of the
manual for description of each part.
Reference to “Right” and “Left” in this book is determined when the machine is viewed from the rear.
Disclaimer
It is the policy of this company to improve its products whenever possible and practical to do so. We
reserve the right to make changes or improvements in the design or construction of parts at any time
without incurring the obligation to install such changes on products previously delivered.
Summers Manufacturing Company, Inc. strongly recommends that each operator READ and UN-
DERSTAND the Operator’s Manual before using the machine. In addition, the Operator’s Manual
should be REVIEWED at least Annually thereafter.
Contact Information
Summers Manufacturing Company, Inc.
103 Summers St. NW
Devils Lake, ND 58301
Toll Free: 1-800-732-4392
Local: 1-701-662-5391 (Devils Lake, ND)
1-605-226-3644 (Aberdeen, SD)
www.summersmfg.com
Owner Registration Information
Bring this information when ordering parts (Serial Number is located at front of hitch).
Name __________________________________ Size ____________________________
Address ________________________________ Serial Number ____________________
City ____________________________________ (located by the hitch)
State/Prov. ______________________________ Date Purchased __________________
Mail Code _______________________________ Dealer __________________________

Page 4 © Summers Mfg. Co., Inc. 2019 8Z1101D
WARRANTY
Summers warrants only products of its manufacture against operational failure caused
by defective materials or workmanship which occur during normal use within 36 months
from the date by the end user from Summers’ dealer.
Summers’ obligation is to replace, free of charge, any part of the product that Summers
inspection shows to be defective excluding transportation charges to Maddock, ND or Devils
Lake, ND and return and also excluding all transportation costs from Summers’ dealer to
the dealer’s customer and all other costs, such as removal and installation expense.
Summers shall not be liable for loss of time, manufacturing costs, labor, material, loss
of prots, consequential damages, direct or indirect, because of defective products whether
due to rights arising under the contract of sale or independently thereof, and whether or not
such claim is based on contract, tort or warranty.
Written permission for any warranty claim return must be rst obtained from authorized
Summers’ personnel. All returns must be accompanied with a complete written explanation
of claimed defects and the circumstances of operational failure.
Written warranty for all component parts used in the manufacture of Summers products
is available upon request. Warranty of such component parts will be determined by said
component manufacturer upon their inspection of the claimed defective part.
This express warranty is the sole warranty of Summers. There are no warranties, which
extend beyond the warranty therein expressly set forth. The sales for products of Summers
under any other warranty or guarantee express or implied is not authorized. This warranty
voids all previous issues.
Summers® Manufacturing Co., Inc.
Devils Lake, ND 58301
01/16

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 5
®
Safety
Safety Information
This safety alert symbol is used to denote possible danger and care should
be taken to prevent bodily injury. When you see this symbol it means
ATTENTION, BECOME ALERT! and/or YOUR SAFETY IS INVOLVED!
WARNING: Safe practices must be followed when working on or
operating this equipment. All personnel involved must:
• Read and understand the instructions and manuals for this machine.
• Be instructed in the safe use of tools and all lifting devices involved in the
assembly of this equipment.
• Clear the area of all personnel not involved in the assembly of this
machine.
General Safety Practices
1. READ and UNDERSTAND the Operator’s Manual before using any equipment. Review at least
annually thereafter.
2. VERIFY all safety devices and shields are in place before using any equipment.
3. KEEP hands, feet, hair and clothing away from moving parts.
4. STOP engine, place all controls in neutral, set parking brake, remove ignition key and wait for
all moving parts to stop before servicing, adjusting, maintaining or unplugging.
5. BE CAREFUL when working around high pressure hydraulic system.
6. DO NOT ALLOW RIDERS.
Safety During Transportation
1. ONLY TOW at a safe speed. Use caution when making corners and meeting tra󰀩c.
2. USE safety chain between tractor drawbar and implement hitch when transporting on public
roads.
3. ALWAYS use transport locks when transporting on public roads.
4. COMPLY with local lighting, marking and oversize regulations when transporting on highways.
5. FREQUENTLY check for tra󰀩c from rear, especially during turns.

Page 6 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Safety
WARNING
DANGER
NOTICE
CAUTION
Safety Decals
Indicates an immediate hazardous situation that will result in death or serious
injury. The color associated with Danger is RED.
Indicates a potentially hazardous situation that could result in death or serious
injury. The color associated with Warning is ORANGE.
Indicates a potentially hazardous situation that may result in minor or moderate
injury. It may also be used to alert against unsafe practices. The color associated
with Caution is YELLOW.
The Notice decals and statements in this manual are to inform the operator
of the correct uids or operational practices for this machine. Failure to follow
these notices will result in damage to the machine. The color associated with
Notice is GREEN.
How to install safety signs?
1. Be sure that the installation area is clean and
dry.
2. Be sure the temperature is above 50° F (10°
C).
3. Decide on the exact position before removing
the backing paper.
4. Remove the smallest portion of the split
backing paper.
5. Align the sign over the specied area and
carefully press the small portion with the
exposed sticky backing in place.
6. Slowly peel back the remaining paper and
carefully smooth the remaining portion of the
sign in place.
7. Small air pockets can be pierced with a pin
and smoothed out using the piece of sign
backing paper.
1. Keep safety signs clean and legible at all
times.
2. Replace safety signs that are missing or
have become illegible.
3. Replaced parts that displayed a safety sign
should also display the current sign.
4. Safety signs are available from your dealer’s
parts department or the factory.

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 7
®
Safety
SH DECALS12/17/2013 9HD0880.iam/
DECALS
3
9
4
12
8
1
7
10
16
5
6
11
13
14
15
2

Page 8 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Safety
Safety Decal Locations
The types of safety signs and locations on the equipment are shown in the illustrations below. Good
safety requires that you familiarize yourself with the various safety signs, the type of WARNING
and the area or particular function related to that area, that requires your SAFETY AWARENESS.
IMPORTANT: If Safety Signs have been damaged, removed, become illegible or parts replaced
without safety signs, new signs must be applied. New safety signs are available
from your authorized dealer.
Safety Decals
DECALS
ITEM PN QTY DESCRIPTION
1 8Z0075 1 TRANSPORT LOCK DECAL
WARNING
REMOVE TRANSPORT LOCK(S) BEFORE LOWERING MACHINE.
IF LOCK(S) DO NOT REMOVE FREELY, INSURE THAT
CYLINDERS ARE COMPLETELY FILLED WITH HYDRAULIC
FLUID AND ARE SUPPORTING THE LOAD TO BE LOWERED.
8Z0075
2 8Z0087 2 “WARNING” PINCH POINT FRAME PINCH POINT HAZARD
KEEP AWAY
To prevent serious injury or death from crushing:
• Stay away from frame hinge area when folding
wings.
• Keep others away.
• Do not fold wings when bystanders are present.
DANGER
8Z0087
3 8Z0092 1 “WARNING” HITCH DECAL
FRAME PINCH POINT HAZARD
KEEP AWAY
To prevent serious injury or death from crushing:
• Stay away from frame hinge area when folding
wings.
• Keep others away.
• Do not fold wings when bystanders are present.
DANGER
8Z0087
3 8Z0093 1 “WARNING” AUTO-FOLD
DECAL
WARNING
AUTO-FOLD LOCK CYLINDER MUST BE FULLY RETRACTED DURING FIELD
OPERATION. HOLD HYDRAULIC LEVER FOR 5 SECONDS AFTER CYLINDER IS
FULLY RETRACTED TO INSURE THAT IT IS FULLY PRESSURIZED. IF THE
TRACTOR HYD. SYSTEM DOES NOT HOLD PRESSURE OR THERE IS A CHANCE
OF ACCIDENTALLY EXTENDING THE LOCK CYLINDER DURING FIELD
OPERATION, MANUAL VALVE MUST BE CLOSED AFTER LOCK IS ENGAGED. IF
AUTO-FOLD LOCK CYLINDER EXTENDS DURING FIELD OPERATION, DAMAGE
WILL OCCUR AND WARRANTY IS VOID. 8Z0093
4 8Z0100 1 MADE IN THE USA DECAL
PROUDLY MADE IN THE U.S.A.
EMPLOYEE
OWNED
WWW.SUMMERSMFG.COM

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 9
®
Safety
Safety Decal Locations (cont’d)
5 8Z0102 1 “IMPORTANT” REAR
JACK(S)
IMPORTANT
RAISE REAR JACK(S)
BEFORE MOVING
IMPLEMENT
8Z0102
6 8Z0204 2 5.5” SUMMERS DECAL
®
7 8Z0232 1 “WARNING” AUTO-FOLD
DECAL
WARNING
STAND CLEAR OF SPRING LOADED
ARMS AND CABLES AT ALL TIMES.
8Z0232
8 8Z0276 1 GENERAL MACHINE
CAUTION DECAL
CAUTION
1. Read and understand Operator’s Manual before using machine.
2. For Sprayers:
a. Read and follow chemical manufacturers’ WARNINGS, instructions and procedures before
using.
b. Use recommended personal protective equipment to reduce or eliminate chemical contact.
c. Never run pump dry.
3. Verify all safety devices and shields are in place before using machine.
4. Keep hands, feet, hair and clothing away from moving parts.
5. Stop engine, place all controls in neutral, set parking brakes, remove ignition key and wait for
all moving parts to stop before servicing, adjusting, maintaining or unplugging.
6. Be careful when working around high pressure hydraulic system.
7. Do not allow riders.
8. Check all wheel bolts DAILY for tightness.
9. Refer to Operator’s Manual for periodic and annual maintenance.
10. For Towed Implements, DO NOT EXCEED 20 MPH.
8Z0276
9 8Z0342 1 INSTALL CYL LOCKS
DECAL
WARNING
TO AVOID INJURY
INSTALL CYLINDER
LOCKS BEFORE
TRANSPORTING OR
SERVICING MACHINE. 8Z0342
10 8Z0344 1 WING DANGER DECAL
TO AVOID INJURY OR DEATH
STAND CLEAR OF MACHINE
WHEN WINGS ARE BEING
RAISED AND LOWERED.
MECHANICAL OR HYDRAU-
LIC FAILURE CAN ALLOW
WINGS TO FALL RAPIDLY.
8Z0344
DANGER

Page 10 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Safety
Safety Decal Locations (cont’d)
11 8Z0346 1 ELECTROCUTION-TILLAGE
EQUIP. DECAL
8Z0346
TO AVOID INJURY OR DEATH
DO NOT CONTACT
ELECTRICAL LINES.
DANGER
12 8Z0800 14 REFLECTOR - YELLOW -
ADHESIVE BACKED
13 8Z0805 4
REFLECTOR - RED-
ORANGE
ADHESIVE BACKED
14 8Z0810 6
REFLECTOR - RED -
ADHESIVE BACKED
15 8Z2120 2 SW4350 DECAL
Safety Light Operation
Figure 1
The Summers Safety Light Kit is equipped with a 7 pin
connector which meets SAE J560 specication. To pro-
tect 7 pin connector, store in dust cap (8K8067) when not
attached to towing vehicle.

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 11
®
Safety
General Maintenance Safety Practices
NOTE: Read the entire section before beginning work.
Before You Begin
• YOU ARE RESPONSIBLE for the safe maintenance of the superweeder.
• DO NOT ALLOW CHILDREN or other unauthorized persons within the superweeder operational
area.
• WEAR PERSONAL PROTECTIVE EQUIPMENT which includes a hard hat, eye protection, work
gloves and steel toed boots with slip resistant soles.
• DO NOT MODIFY the equipment or substitute parts in any way. Unauthorized modications may
impair the function and/or safety of the machine.
• USE SUITABLE LIFTING DEVICE for components which could cause personal injury.
• BLOCK UP ANY RAISED PART of the machine. Be sure machine is stable after blocking.
• ALWAYS INSPECT LIFTING CHAINS AND SLINGS for damage or wear.
• BE SURE LIFTING DEVICE IS RATED TO HANDLE THE WEIGHT.
• STOP ENGINE,place all controls in neutral, set parking brake, remove ignition key and wait for
all moving parts to stop before servicing or adjusting.
• BE SURE PRESSURE IS RELIEVED from hydraulic circuits before servicing or disconnecting
from tractor.
• USE EXTREME CARE when assembling, servicing or adjusting.
• Never Unhitch a 4-Rank Superweeder that has been opened up into eld position but has not
been completely lowered to the ground.
• Always park machine in a level area, block hitch and tranport tires so machine cannot roll.
• Always be sure transport locks are engaged when making adjustments on machine in raised or
transport position.
• Never rotate S-tines forward or backward with machine in transport position.

Page 12 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Operation
TRANSPORT TO FIELD POSITION
1. Hitch machine to tractor drawbar using a locking hitch pin and safety chain. Connect hydraulic
hoses and wiring. Retract jacks and rotate into storage position.
2. Select a level area to lower machine into eld position.
3. IMPORTANT: Remove transport locks. Store locks in storage guide
4. Back up machine slowly, maneuvering so wings open evenly. If wings do not open evenly, pull
ahead and repeat procedure. Cables must not catch on machine while backing up. If cable be-
comes caught on machine, drive forward until wings are in transport position and carefully unhook
cable from obstruction.
5. Open wings until auto-fold arms rest on hitch and cables become slack. Fully retract auto-fold
lock cylinder until autofold arms are locked in place and the hinged wing cylinder is fully retracted
(if applicable)
6. Extend main lift cylinders to lower machine into field position.If pull cables become
tight before transport wheel is off the ground, back up to provide slack in cable.
FIELD TO TRANSPORT POSITION
1. Stop in a level area and back tractor up to provide slack in pull cables.
2. Open manual lock valve on auto-fold lock cylinder. Fully extend auto-fold lock cylinder.
3. Fully retract hydraulic depth adjustment cylinders (if so equipped).
4. Fully retract lift cylinders to raise sections.
5. While machine is resting on its transport wheels, drive tractor forward. Wings should fold to trans-
port position. NOTE: Transport wheels must rotate against “toe-in” adjustment bolts and follow
directly behind knuckles. Transport wheel “toe-in” can be adjusted by moving outside 3/4” adjust-
ment set screws (8X0665, page 6-5). “Toe-in” and proper lubrication of pivot will make it easier
to unfold machine into eld position.
6. IMPORTANT: Install transport locks.
Machine must not be adjusted to exceed a maximum S-tine tillage depth of 5” in loose soil
conditions. In hard soil conditions, S-tines must not exceed 3” tillage depth.
HYDRAULIC DEPTH ADJUSTMENT (HDA) OPTION
To set depth, install stroke control collars (purchase locally) on 3-1/2” X 8” stroke (HDA) cylinders lo-
cated on hitch. Collars of identical thickness must be installed on both cylinders. Rephasing cylinders
are used for hydraulic depth adjustment. Do not operate HDA cylinders fully extended. Immediately
after fully raising hydraulic depth adjustment cylinders, quickly lower 1/2”. If hydraulic depth adjust-
ment cylinders are left in fully raised position, they will settle. If machine has settled unevenly, fully
extend hydraulic depth adjustment cylinders and hold hydraulic lever until machine levels. After it
levels, quickly lower 1/2”.

®
8Z1101D © Summers Mfg. Co., Inc. 2019 Page 13
Maintenance & Specications
Daily Maintenance:
Check all wheel bolts for tightness.
Daily Greasing:
Two zerks on each knuckle.
Two zerks on each cable fold arm.
One zerk on each transport axle pivot.
60 & 70 Ft. machines only: One zerk on
each Hinged Wing Pivot.
Weekly Maintenance:
Inspect wheel bearings for tightness.
Seasonal Maintenance:
Disassemble, clean and repack wheel bearings.
Lubricate all zerks with a good grade of general purpose grease.
Inspect entire machine for loose or worn fasteners. Tighten or replace as required.
TIRE INFLATION: IF 280 70 R15 - 64 PSI 40 MPH maximum. Exceeding
this speed voids warranty.
TROUBLESHOOTING
1. Wings trail too far apart in trans-
port. Insu󰀩cient transport wheel toe-in. Adjust transport wheel toe-in.
2. Wings are not pulling evenly in eld
position.
Cable pull brackets are improperly
located.
Relocate cable pull brackets so wings
slightly lead center.
3. Auto-Fold arms do not rotate into
transport position. Improper pivot bracket adjustment.
Adjust pivot bracket with bolts to
provide clearance between the cable
fold arm bottom guide and hitch tube.
(6-4)
4. Wings of machine bounce. Improper wing support tire ination. Inate tires to proper pressure.
5. Harrow sections not riding level. Top pull chains are improperly ad-
justed.
Adjust top pull chain by placing pin in
di󰀨erent adjustment hole on lift arm.
6. S-tines tend to rotate out of the
ground
Hydraulic cylinder leaking. Repair or replace hydraulic cylinder.
Tractor hydraulic circuit not holding
pressure. Repair tractor valve.

Page 14 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Parts
DESCRIPTIONPNITEM
CLAMP HOSE 5" #728A10041
HYD CYL 5" X 32" 3500PSI8C05322
PIN 1 X 5-7/8" 22'HTCH PLTD8C14203
PIN 1 X 6-1/2" CYL DBLWSHR8C14524
PIN 1-1/4 X 14" PIVOT8C14705
U-BOLT 3/8 X 8 X 5" SQ8C17026
U-BOLT 3/4 X 8-1/16 X 6" SQ8C17607
CLAMP 1/2" WIRE ROPE8C19008
SPRING AFLDCABL 1.56"OD GLVNZD8C19209
SPRING AUTOFOLD ARM RAW8C1940
10
SPRING AFOLD LOCK 3"OD BLACK8C1950
11
22' HITCH8C220012
TRNSPRT LOCK 1/2X3X32"CYL8C224613
OSCILLATING AXLE ASSY8C231414
SPACR BRCKT HTCH AXL ATTCH8C231815
PIVOT BRCKT A-FLD 22'HTCH8C262016
ARM A-FLD LEFT 20&22'HTCH8C263017
ARM A-FLD RGHT 20&22'HTCH8C263518
LOCK ASSY AUTOFLD 22'HTCH 90-8C265019
BUSHING A-FOLD LOCK- 5/16"8C266020
FRONT ATTCH DUAL CABLE8C269021
A-FLD ARM LIFTER8C270022
A-FLD ARM LFTER BOLT PLATE8C271023
CLEVIS FOR EYE-EYE CABLE 99-8D031224
HITCH PIECE CAST CAT.3CTD PNTD8D072025
CHAIN 3 LINK .625"DIA. ALLOY Z
8D240226
SAFETY CHAIN 3/8" X 4'
8D246027
PIN 1 X 2-3/4" CABLE PLATED
8D273028
IF280/70R15 134D ON 15X10X6WHL8D304629
HYD HOSE HOLDER PNTD BLK 91-8D850230
JACK 7000# SIDE CRANK 15" LIFT8D853731
HYD CYL 2.5 X8" W/O DPTHCNTRL8D911832
HUB&AXLE ASSY 614(GBGI-2"RCVR)8K110033
PIN 1-1/4 X 6-1/8"8K162034
EYEBOLT 1.25DIAX1"EYE YZ 12-8K172035
MODULE AG ENHNCDW/BRAKE6PIN08-8K8030A36
EYEBOLT 3/4"-10NC X 5/8"EYE8R614537
BOLT WHEEL 9/16"-18 UNF- 1.25"8R691438
QUICKLINK 1/4" YELLOW ZINC8S107639
BOLT PIVOT CHSLTRP&WNGLFT YZ8T330040
HOLDER MANUAL-PAK8T438541
U-BOLT 1/2 X 3 X 3" SQ
8W120442
MANIFOLD BLOCK ALUMINUM 10PORT
8W136043
BOLT 3/8-16NC X 2" GR5 ZDI
8X000844
BOLT 1/2-13NC X 1-1/2" GR5 YZ8X0063
45
BOLT 1/2-13NC X 4-1/2" GR5 ZDI8X007446
BOLT 3/4-10NC X 1-1/4" GR5 YZ8X011047
BOLT 3/4-10NC X 10" GR5 ZDI8X012548
BOLT 1-8NCX7" W/1.5"THDGR5 YZ8X014049
BOLT 1-8NC X 20" GR5 YZ8X015050
SCREW 8 X .75" FLANGE HD8X017051
NUT 3/8"-16NC NY-LOCK GR2 YZ8X020252
NUT 3/8"-16NC SERFLANG GR2 YZ8X020353
NUT 8-32 HEX YZ SER FLNG8X020854
NUT 1/2"-13NC NY-LOCK GR2 YZ8X024255
NUT 1/2"-13NC SERFLANG GR2 YZ8X024656
NUT 3/4"-10NC HEX GR2 YZ8X026057
NUT 3/4"-10NC NY-LOCK GR2 YZ8X026158
NUT 3/4"-10NC CNTRLOCK GR2 YZ
8X026559
NUT 1"-8NC HEX GR2 YZ
8X028060
NUT 1"-8NC NY-LOCK GR2 YZ
8X028161
NUT 1"-14TPI TOPLOCK GR 8 Z8X028262
NUT 1-1/4"-7NC HEX GR2 YZ8X028463
LOCKWASHER 3/4" YLW ZNC8X030664
LOCKWASHER 1" YLW ZNK8X030965
LOCKWASHER 1-1/4" YLW ZNC8X031166
WASHER 3/4"(13/16"ID)FLAT YZ8X031867
WASHER 1-1/4" SAE FLAT YZ8X032768
COTTER PIN 1/4 X 2" YZ8X041469
COTTER PIN 3/16 X 1-1/2"8X041570
COTTER PIN 5/16 X 2-1/2" YZ8X041871
LIGHT MODULE BRACKET8X080372
MANUAL-PAK 3DIA X 11.75" 09-8Z100073
B
HITCH (NO HDA)3/21/2019 9W7022A.iam/
HITCH (NO HDA)
47
67
30
67
13
69
2
68
34
68 71
15
59
64
46
48
14
55 33
29
38
12
65
60
61
27
49
67
58
61
20
69
28
21
26 24
32 37 11
7
5
45
64
57
16
10
58
37
89
39
42
56
1
73
70
61 30
31
41
55
3
471
44
43
36
52
54
51 53
6
72
18
17
19
55
23
22 46
4
69
40
62
25
50
63
66
35

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 15
®
Parts
HITCH PARTS LIST
ITEM PN DESCRIPTION
1 8A1004 CLAMP HOSE 5" #72
2 8C0532 HYD CYL 5" X 32" 3500PSI
3 8C1420 PIN 1 X 5-7/8" 22'HTCH PLTD
4 8C1452 PIN 1 X 6-1/2" CYL DBLWSHR
5 8C1470 PIN 1-1/4 X 14" PIVOT
6 8C1702 U-BOLT 3/8 X 8 X 5" SQ
7 8C1760 U-BOLT 3/4 X 8-1/16 X 6" SQ
8 8C1900 CLAMP 1/2" WIRE ROPE
9 8C1920 SPRING AFLDCABL 1.56"OD GLVNZD
10 8C1940 SPRING AUTOFOLD ARM RAW
11 8C1950 SPRING AFOLD LOCK 3"OD BLACK
12 8C2200 22' HITCH
13 8C2246 TRNSPRT LOCK 1/2X3X32"CYL
14 8C2314 OSCILLATING AXLE ASSY
15 8C2318 SPACR BRCKT HTCH AXL ATTCH
16 8C2620 PIVOT BRCKT A-FLD 22'HTCH
17 8C2630 ARM A-FLD LEFT 20&22'HTCH
18 8C2635 ARM A-FLD RGHT 20&22'HTCH
19 8C2650 LOCK ASSY AUTOFLD 22'HTCH 90-
20 8C2660 BUSHING A-FOLD LOCK- 5/16"
21 8C2690 FRONT ATTCH DUAL CABLE
22 8C2700 A-FLD ARM LIFTER
23 8C2710 A-FLD ARM LFTER BOLT PLATE
24 8D0312 CLEVIS FOR EYE-EYE CABLE 99-
25 8D0720 HITCH PIECE CAST CAT.3CTD PNTD
26 8D2402 CHAIN 3 LINK .625"DIA. ALLOY Z
27 8D2460 SAFETY CHAIN 3/8" X 4'
28 8D2730 PIN 1 X 2-3/4" CABLE PLATED
29 8D3046 IF280/70R15 134D ON 15X10X6WHL
30 8D8502 HYD HOSE HOLDER PNTD BLK 91-
31 8D8537 JACK 7000# SIDE CRANK 15" LIFT
32 8D9118 HYD CYL 2.5 X8" W/O DPTHCNTRL
33 8K1100 HUB&AXLE ASSY 614(GBGI-2"RCVR)
34 8K1620 PIN 1-1/4 X 6-1/8"
35 8K1720 EYEBOLT 1.25DIAX1"EYE YZ 12-
36 8K8030A MODULE AG ENHNCDW/BRAKE6PIN
37 8R6145 EYEBOLT 3/4"-10NC X 5/8"EYE
38 8R6914 BOLT WHEEL 9/16"-18 UNF- 1.25"
39 8S1076 QUICKLINK 1/4" YELLOW ZINC
40 8T3300 BOLT PIVOT CHSLTRP&WNGLFT YZ
41 8T4385 HOLDER MANUAL-PAK
42 8W1204 U-BOLT 1/2 X 3 X 3" SQ
43 8W1360 MANIFOLD BLOCK ALUMINUM10PORT
44 8X0008 BOLT 3/8-16NC X 2" GR5 ZDI
45 8X0063 BOLT 1/2-13NC X 1-1/2" GR5 YZ
46 8X0074 BOLT 1/2-13NC X 4-1/2" GR5 ZDI
47 8X0110 BOLT 3/4-10NC X 1-1/4" GR5 YZ
48 8X0125 BOLT 3/4-10NC X 10" GR5 ZDI
49 8X0140 BOLT 1-8NCX7" W/1.5"THDGR5 YZ
50 8X0150 BOLT 1-8NC X 20" GR5 YZ
51 8X0170 SCREW 8 X .75" FLANGE HD
52 8X0202 NUT 3/8"-16NC NY-LOCK GR2 YZ
53 8X0203 NUT 3/8"-16NC SERFLANG GR2 YZ
54 8X0208 NUT 8-32 HEX YZ SER FLNG
55 8X0242 NUT 1/2"-13NC NY-LOCK GR2 YZ
56 8X0246 NUT 1/2"-13NC SERFLANG GR2 YZ
57 8X0260 NUT 3/4"-10NC HEX GR2 YZ
58 8X0261 NUT 3/4"-10NC NY-LOCK GR2 YZ
59 8X0265 NUT 3/4"-10NC CNTRLOCK GR2 YZ
60 8X0280 NUT 1"-8NC HEX GR2 YZ
61 8X0281 NUT 1"-8NC NY-LOCK GR2 YZ
62 8X0282 NUT 1"-14TPI TOPLOCK GR 8 Z
63 8X0284 NUT 1-1/4"-7NC HEX GR2 YZ
64 8X0306 LOCKWASHER 3/4" YLW ZNC
65 8X0309 LOCKWASHER 1" YLW ZNK
66 8X0311 LOCKWASHER 1-1/4" YLW ZNC
67 8X0318 WASHER 3/4"(13/16"ID)FLAT YZ
68 8X0327 WASHER 1-1/4" SAE FLAT YZ
69 8X0414 COTTER PIN 1/4 X 2" YZ
70 8X0415 COTTER PIN 3/16 X 1-1/2"
71 8X0418 COTTER PIN 5/16 X 2-1/2" YZ
72 8X0803 LIGHT MODULE BRACKET
73 8Z1000 MANUAL-PAK 3DIA X 11.75" 09-

Page 16 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Parts
DETAIL A
DETAIL B
DETAIL C
DESCRIPTIONPNITEM
PIN 1-1/2 X 11-1/2" KNCKL8C14801
U-BOLT 3/8 X 8 X 9" SQ8C17102
U-BOLT 7/8 X 8-1/16 X 10" SQ8C1780
3
KNUCKLE 88.25°OFFSET LEFT8C1800
4
KNUCKLE 88.25°OFFSET RIGHT8C1802
5
CENTER 22' HTCH 8"SQ-10'8C22126
BRCKT CABLE PULL 8"SQ WNG8C2260
7
JACK ATTCH BRCKT- WING8C22808
TRNSPRT AXLE 2.5" RCVR 90°8C24249
CLEVIS FOR EYE-EYE CABLE 99-8D031210
PIN 1 X 2-3/4" CABLE PLATED8D273011
IF280/70R15 134D ON 15X10X6WHL8D304612
IF280/70R15 134D ON 15X8X8WHL8D306013
JACK 7000# SIDE CRANK 15" LIFT8D853714
HUB&AXLE ASSY 614(GBGI-2"RCVR)8K110015
HUB&AXLE ASSY HD812(2.5"RCVR)8K110516
BRCKT SMV ATTCH 4-8"FRAME98-8K820018
PIN 2 X 13-1/2" HARDENED GREASABLE8P391219
BOLT WHEEL 9/16"-18 UNF- 1.25"8R691420
SIGN SLOW MOVING VEHICLE(SMV)8S1120
21
MNT SPADE W/HRDWR SMV SIGN8S1126
22
8W175023
SPINDLE HOLDER 2"8W800424
HYD CYL 2.5 X 4"8W800525
WINGTUBE15' X 8SQ 60'&70'8W800726
WINGTUBE 15' PRT2 (70')8W800827
STL 1" 14.5X2.25"8W800928
HINGED WING PIN8W801029
BOLT 5/16-18NC X 1-1/4"GR5 YZ8X0021B30
BOLT 1/2-13NC X 2-1/2" GR5 YZ8X006831
BOLT 1/2-13NC X 3-3/4" GR5 YZ8X007232
BOLT 1/2-13NC X 4-1/2" GR5 ZDI8X007433
BOLT 5/8-11NC X 5" GR5 ZDI8X009534
BOLT 3/4-10NC X 3" GR5 YZ8X011435
BOLT 1-8NC X 3.5" GR5 YZ8X014236
NUT 3/8"-16NC SERFLANG GR2 YZ
8X020337
NUT 5/16"-18NC SERFLANG GR2 YZ
8X021138
NUT 1/2"-13NC NY-LOCK GR2 YZ
8X024239
NUT 5/8"-11NC NY-LOCK GR2 YZ8X025340
NUT JAM 3/4"-10NC GR2 ZDI8X025941
NUT 3/4"-10NC HEX GR2 YZ8X026042
NUT 7/8"-9NC HEX GR2 YZ8X026843
NUT 1"-8NC NY-LOCK GR2 YZ8X028144
NUT 1-1/2"-6NC JAM GR2 YZ8X028645
LOCKWASHER 3/4" YLW ZNC8X030646
LOCKWASHER 7/8" YLW ZNC8X030747
WASHER 1" SAE FLAT YZ8X031648
WASHER 17/32"ID X 1.25"OD YZ8X033049
WASHER 2.03IDX2-7/8ODX 9GA PLN8X036250
WASHER 2.03IDX2-7/8ODX 1/4"PLN8X036651
COTTER PIN 1/4 X 2" YZ8X041452
COTTER PIN 5/16 X 2-1/2" YZ8X041853
SET SCRW SQ HD 3/4-10X4.5" YZ
8X066554
A
B
C
DRAWBAR SW20
10/21/2019 9W7022B.iam/
26
3
23
47
43
43
47
8
14
43
47
52
10 7
11
3
15
39
24
46
42
32
12
20
27
25
28
48
36
44
24
39 15
32
29
34
40
19
5
6
2
37
30
21
18
22 38
4
31
49
1
39
45
12
13 50
51
53
43
47
16 39
33
9
35
54
41
17

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 17
®
Parts
DRAWBAR PARTS LIST
ITEM PN DESCRIPTION
1 8C1480 PIN 1-1/2 X 11-1/2” KNCKL
2 8C1710 U-BOLT 3/8 X 8 X 9” SQ
3 8C1780 U-BOLT 7/8 X 8-1/16 X 10” SQ
4 8C1800 KNUCKLE 88.25° OFFSET LEFT
5 8C1802 KNUCKLE 88.25° OFFSET RIGHT
6 8C2212 CENTER 22’ HTCH 8”SQ-10’
7 8C2260 BRCKT CABLE PULL 8”SQ WNG
8 8C2280 JACK ATTCH BRCKT- WING
9 8C2424 TRNSPRT AXLE 2.5” RCVR 90°
10 8D0312 CLEVIS FOR EYE-EYE CABLE 99-
11 8D2730 PIN 1 X 2-3/4” CABLE PLATED
12 8D3046 IF280/70R15 134D ON 15X10X6WHL
13 8D3060 IF280/70R15 134D ON 15X8X8WHL
14 8D8537 JACK 7000# SIDE CRANK 15” LIFT
15 8K1100 HUB&AXLE ASSY 614(GBGI-2”RCVR)
16 8K1105 HUB&AXLE ASSY HD812(2.5”RCVR)
17 8K7123 NUT WHEEL BOLT 5/8-18UNF 97-
18 8K8200 BRCKT SMV ATTCH 4-8”FRAME98-
19 8P3912 PIN 2 X 13-1/2” HARDENED GREASABLE
20 8R6914 BOLT WHEEL 9/16”-18 UNF- 1.25”
21 8S1120 SIGN SLOW MOVING VEHICLE(SMV)
22 8S1126 MNT SPADE W/HRDWR SMV SIGN
23 8W1750 CABLE GUIDE BRACKET
24 8W8004 SPINDLE HOLDER 2”
25 8W8005 HYD CYL 2.5 X 4”
26 8W8007 WINGTUBE15’ X 8SQ 60’&70’
27 8W8008 WINGTUBE 15’ PRT2 (70’)
28 8W8009 STL 1” 14.5X2.25”
29 8W8010 HINGED WING PIN
30 8X0021B BOLT 5/16-18NC X 1-1/4”GR5 YZ
31 8X0068 BOLT 1/2-13NC X 2-1/2” GR5 YZ
32 8X0072 BOLT 1/2-13NC X 3-3/4” GR5 YZ
33 8X0074 BOLT 1/2-13NC X 4-1/2” GR5 ZDI
34 8X0095 BOLT 5/8-11NC X 5” GR5 ZDI
35 8X0114 BOLT 3/4-10NC X 3” GR5 YZ
36 8X0142 BOLT 1-8NC X 3.5” GR5 YZ
37 8X0203 NUT 3/8”-16NC SERFLANG GR2 YZ
38 8X0211 NUT 5/16”-18NC SERFLANG GR2 YZ
39 8X0242 NUT 1/2”-13NC NY-LOCK GR2 YZ
40 8X0253 NUT 5/8”-11NC NY-LOCK GR2 YZ
41 8X0259 NUT JAM 3/4”-10NC GR2 ZDI
42 8X0260 NUT 3/4”-10NC HEX GR2 YZ
43 8X0268 NUT 7/8”-9NC HEX GR2 YZ
44 8X0281 NUT 1”-8NC NY-LOCK GR2 YZ
45 8X0286 NUT 1-1/2”-6NC JAM GR2 YZ
46 8X0306 LOCKWASHER 3/4” YLW ZNC
47 8X0307 LOCKWASHER 7/8” YLW ZNC
48 8X0316 WASHER 1” SAE FLAT YZ
49 8X0330 WASHER 17/32”ID X 1.25”OD YZ
50 8X0362 WASHER 2.03IDX2-7/8ODX 9GA PLN
51 8X0366 WASHER 2.03IDX2-7/8ODX 1/4”PLN
52 8X0414 COTTER PIN 1/4 X 2” YZ
53 8X0418 COTTER PIN 5/16 X 2-1/2” YZ
54 8X0665 SET SCRW SQ HD 3/4-10X4.5” YZ

Page 18 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Parts
DESCRIPTIONPNITEM
U-BOLT 3/4 X 8-1/16 X 6" SQ8C17601
22' HITCH8C2200
2
OSCILLATING AXLE ASSY8C2314
3
TIRE IF 280/70R15 134D TUBELESS8D3045
4
IF 280/70R15 134D ON 15X10X6WHL8D3046
5
IF280/70R15 134D ON 15X10X6WHL8D30466
ROLL PIN 1/4 X 2" ZINC8D9108
7
HUB&AXLE ASSY 614(GBGI-2"RCVR)8K11008
HYD CYL 3" X 8" RPHS 1.5" ROD8K84309
HYD CYL 3.5" X 8" RPHS 1.75" ROD8K843510
PIN 1 X 4" CYL-FOR1/4"ROLL PIN8K910211
STL 12GA X 1.75- 4" W/HLS 08-8R606012
PILLOWBLOCK CAP W/ZERK CAST8R606513
PILLOWBLOCK CAP CAST PNTD8R606714
BOLT WHEEL 9/16"-18 UNF- 1.25"8R691415
BOLT PIVOT CHSLTRP&WNGLFT YZ8T330016
STL 1" - 24.25 X 15.5"8W166017
STL 3/4" - 10 X 7.25"
8W180218
SPACER TUBE 1.25X.76- 1-1/16"
8W180619
PIVOT W/SPNDL HLDR WNG LFT SW
8W184020
PIVOT W/SPNDL HLDR WNG RGHT SW8W184221
STL 1" - 17.75 X 4.75"8W184522
HITCH PIVOT ASSY 22' HDA8W185023
CYL ATTCH HTCH UBLT LEFT8W186024
CYL ATTCH HTCH UBLT RGHT8W186225
L UHMW 2.5X2.5X3/8- 13" W/HLS8W188426
FLAT 5/16X 1.5 - 11-3/8"8W188627
ROLLERTUBE 1.5 X 1"ID- 1.5" 94-8W189028
NYLATRON 1"ODX .76"ID- 1-1/2"8W189529
BOLT 1/2-13NC X 3-1/4" GR5 YZ8X007030
BOLT 1/2-13NC X 4-1/2" GR5 ZDI8X007431
BOLT 5/8-11NC X 2-3/4" GR5 YZ8X009232
BOLT 3/4-10NC X 3" GR5 YZ8X011433
BOLT 3/4-10NC X 3-1/2" GR5 YZ
8X011534
BOLT 3/4-10NC X 6-1/2" GR5 YZ
8X012135
BOLT 3/4-10NC X 4-1/2" GR5 YZ
8X012236
BOLT 1-8NC X 5" GR5 YZ8X014337
NUT 1/2"-13NC NY-LOCK GR2 YZ8X024238
NUT 5/8"-11NC HEX GR2 YZ8X025039
NUT 3/4"-10NC HEX GR2 YZ8X026040
NUT 3/4"-10NC NY-LOCK GR2 YZ8X026141
NUT 3/4"-10NC CNTRLOCK GR2 YZ8X026542
NUT 1"-8NC NY-LOCK GR2 YZ8X028143
NUT 1"-14TPI TOPLOCK GR 8 Z8X028244
LOCKWASHER 5/8" YLW ZNC8X030445
LOCKWASHER 3/4" YLW ZNC8X030646
WASHER 1" SAE FLAT YZ8X031647
WASHER 1" SAE FLAT YZ8X031648
HYD DEPTH ADJUST
11/12/2019 9W5022B.iam/
46 40
41
19
22
43
40
46
18
9
17 33
20 37
36
30
8
38
37
47
15
28
29
42
34
39
45 14
12 13
32
46
40
10 23
2
35
27
26
41
3
31
38
8
6
15
1
11
7
16
4 7
44
21
RIGHT
LEFT
45
25
24

8Z1101D © Summers Mfg. Co., Inc. 2019 Page 19
®
Parts
HYDRALIC DEPTH ADJUST
ITEM PN DESCRIPTION
1 8C1760 U-BOLT 3/4 X 8-1/16 X 6" SQ
2 8C2200 22' HITCH
3 8C2314 OSCILLATING AXLE ASSY
4 8D3045 TIRE IF 280/70R15 134D TUBELESS
5 8D3046 IF 280/70R15 134D ON 15X10X6WHL
6 8D3046 IF280/70R15 134D ON 15X10X6WHL
7 8D9108 ROLL PIN 1/4 X 2" ZINC
8 8K1100 HUB&AXLE ASSY 614(GBGI-2"RCVR)
9 8K8430 HYD CYL 3" X 8" RPHS 1.5" ROD
10 8K8435 HYD CYL 3.5" X 8" RPHS 1.75" ROD
11 8K9102 PIN 1 X 4" CYL-FOR1/4"ROLL PIN
12 8R6060 STL 12GA X 1.75- 4" W/HLS 08-
13 8R6065 PILLOWBLOCK CAP W/ZERK CAST
14 8R6067 PILLOWBLOCK CAP CAST PNTD
15 8R6914 BOLT WHEEL 9/16"-18 UNF- 1.25"
16 8T3300 BOLT PIVOT CHSLTRP&WNGLFT YZ
17 8W1660 STL 1" - 24.25 X 15.5"
18 8W1802 STL 3/4" - 10 X 7.25"
19 8W1806 SPACER TUBE 1.25X.76- 1-1/16"
20 8W1840 PIVOT W/SPNDL HLDR WNG LFT SW
21 8W1842 PIVOT W/SPNDL HLDR WNG RGHT SW
22 8W1845 STL 1" - 17.75 X 4.75"
23 8W1850 HITCH PIVOT ASSY 22' HDA
24 8W1860 CYL ATTCH HTCH UBLT LEFT
25 8W1862 CYL ATTCH HTCH UBLT RGHT
26 8W1884 L UHMW 2.5X2.5X3/8- 13" W/HLS
27 8W1886 FLAT 5/16X 1.5 - 11-3/8"
28 8W1890 ROLLERTUBE 1.5 X 1"ID- 1.5" 94-
29 8W1895 NYLATRON 1"ODX .76"ID- 1-1/2"
30 8X0070 BOLT 1/2-13NC X 3-1/4" GR5 YZ
31 8X0074 BOLT 1/2-13NC X 4-1/2" GR5 ZDI
32 8X0092 BOLT 5/8-11NC X 2-3/4" GR5 YZ
33 8X0114 BOLT 3/4-10NC X 3" GR5 YZ
34 8X0115 BOLT 3/4-10NC X 3-1/2" GR5 YZ
35 8X0121 BOLT 3/4-10NC X 6-1/2" GR5 YZ
36 8X0122 BOLT 3/4-10NC X 4-1/2" GR5 YZ
37 8X0143 BOLT 1-8NC X 5" GR5 YZ
38 8X0242 NUT 1/2"-13NC NY-LOCK GR2 YZ
39 8X0250 NUT 5/8"-11NC HEX GR2 YZ
40 8X0260 NUT 3/4"-10NC HEX GR2 YZ
41 8X0261 NUT 3/4"-10NC NY-LOCK GR2 YZ
42 8X0265 NUT 3/4"-10NC CNTRLOCK GR2 YZ
43 8X0281 NUT 1"-8NC NY-LOCK GR2 YZ
44 8X0282 NUT 1"-14TPI TOPLOCK GR 8 Z
45 8X0304 LOCKWASHER 5/8" YLW ZNC
46 8X0306 LOCKWASHER 3/4" YLW ZNC
47 8X0316 WASHER 1" SAE FLAT YZ

Page 20 © Summers Mfg. Co., Inc. 2019 8Z1101D
®Parts
DETAIL A
A
DESCRIPTIONPNITEM
EYE BOLT SHORT 7/16" DIA8D17101
EYE BOLT LONG 1/2" DIA8D17202
SPRING PRESS 3/8" C-HRRW OPT8D17303
PIPE 1/2"SCH80- 2-1/8" W/WSHR8D17404
PIPE 1/2" SCH80- 1-1/4" -078D17505
CHAIN 6 LINK CASE HARDND-12.5"8D21006
CHAIN 8 LINK CASE HARDEND-17"8D22107
HYD CYL 2.5 X 8" SP W/ DEPTH CNTRL8D91168
TUBE8H13209
U-BOLT 3/4 X 2-1/8 X 4-1/4" SQ
8K550510
PLOWBOLT 3/8"X1.5"
8W100611
3/8" HVY NUT8W100712
S-TINE HIGH8W101213
CLAMP HI CLEARANCE S-TINE8W1014H14
SHOVEL 1/4 X 4" STINE8W102115
TUBE SQ 2 X 4T - P 18-8W122916
FLAT 3/8X1.5- 50" 4RNK SW 91-8W126417
LEVER 2"SQ TUBE SW-P 18-8W1271P18
CYL ATTCH LVR ROD SW -P 18-8W1281P19
BUSHING 2" SQ TUBE/S-TINE8W130020
WEEDER ARM BOLT PLATE8W800121
WEEDER ARM8W800222
TINE ADJUST CYL ATTACH8W800323
BOLT 7/16X1.25 5/8"THD GR5 ZDI8X003324
BOLT 7/16-14NC X 3-1/2"GR5 ZDI8X004425
CRG 7/16-14NC X 3-1/2" GR5 ZDI
8X004826
BOLT 1/2-13NC X 1-1/2" GR5 YZ
8X006327
BOLT 1/2-13NC X 2-1/4" GR5 ZDI8X006728
BOLT 1/2-13NC X 3" GR5 ZDI8X006929
BOLT 1/2-13NC X 3-3/4" GR5 YZ8X007230
BOLT 1-8NC X 6" FULL THRD8X0138A31
BOLT 1-8NC X 5" GR5 YZ8X014332
NUT 7/16"-14NC HEX GR2 ZDI8X023233
NUT 7/16"-14NC CNTRLOCK8X023334
NUT 1/2"-13NC HEX GR2 YZ8X024035
NUT 1/2"-13NC NY-LOCK GR2 YZ8X024236
NUT 3/4"-10NC HEX GR2 YZ8X026037
NUT JAM 1"-8NC GR2 ZDI8X027738
NUT 1"-8NC NY-LOCK GR2 YZ8X028139
LOCKWASHER 7/16" YLW ZNC8X030240
LOCKWASHER 1/2" YLW ZNC8X030341
LOCKWASHER 3/4" YLW ZNC
8X030642
LOCKWASHER 1" YLW ZNC
8X030943
WASHER 3/8" (7/16" ID)FLAT ZDI
8X032044
WASHER 17/32"ID X 1.25"OD YZ8X033045
WASHER 17/32"ID X 1.25"OD BLACK8X0330B46
COTTER PIN 3/16 X 1-1/2"8X041547
LYNCH PIN 3/16 X 1-1/4" YZ8X049248
SET SCRW SQ HD 7/16-14X 1" ZDI8X060549
WEEDER ARMS SW20
10/21/2019 9W7022B.iam/
36
45 30
7
6
7
36
27
24 20
36
40 33
22 23
29
8
39
32
39
21
43
31
38
45
48
46
47
1
4
2
41
35
49 33
5
28
3
9
45
28
36
17
25
40
33
18
19
37
42
10
16
26
40
34
11
15
44
12
8W1229 (6 TINE BAR)
8W1248 (9 TINE BAR)
HIGH CLEARANCE 8W1014H & 8W1012
STANDARD 8W1014 & 8W1011
14
13