Summit COOL1D User manual

WINE COOLER/REFROIDISSEUR DE VIN
INSTRUCTION MANUAL/ MANUEL D'INSTRUCTIONS
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS. /
AVANT UTILISATION, VEUILLEZ LIRE ET SUIVRE TOUTES LES RÈGLES DE
SÉCURITÉ ET LES
INSTRUCTIONS D'UTILISATION.
Felix Storch, Inc.
An ISO 9001:2015 registered company
770 Garrison Ave
Bronx, New York 10474
www.summitappliance.com
Model No. / No. des Modèles: COOL1D / LX1D / WC1D
Write Model and Serial Numbers here/ Écrivez les numéros de
modèle et de série ici :
Model No/ Modèle No.:
Serial No/ Serie No.:

2
TABLE OF CONTENTS
Appliance Safety 3
Important Safeguards 3-4
Location of Parts 5
Installation Instructions 6-10
Before Using your Appliance 6
Installation of your Appliance 6-9
Shelves and Capacity 10
Electrical Connection 11
Extension Cord 11
Installing the Stainless Steel Handle 12
Full Overlay Panel Installation Instructions 12
Operating your Appliance 13-14
Control Panel 13
Setting the Temperature Control 13
Interior Light 13
Sabbath Mode 14
Defrosting 14
Warning System 14
Care and Maintenance 15
Cleaning your Appliance 15
Power Failure 15
Vacations 15
Moving your Appliance 15
Energy-Saving Tips 15
Troubleshooting 16
Limited Warranty 17
French Version of the Manual 18-32

3
APPLIANCE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the Safety Alert Symbol. The symbol alerts you to potential hazardsthat
can kill or injure you and others. All safety messages will follow the SafetyAlert
Symbol and either the word DANGER or WARNING.
DANGER means that failure to heed this safety
statement may result in severe personal injury or
death.
WARNING means that failure to
heed this safety statement may
result in extensive product damage,
serious personal injury, or death.
All safety messages will alert you about the potential hazard, tell you how to reduce the chance of injury,
and let you know what can happen if the instructions are not followed.
IMPORTANT SAFEGUARDS
Before the appliance is used, it must be properly positioned and installed as described in
this manual, so read the manual carefully. To reduce the risk of fire, electrical shock or
injury when using the appliance, follow basic precautions, including the following:
• Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter,and
do not use an extension cord.
• Replace all panels before operating.
• It is recommended that a separate circuit serving only your appliance be provided.Use
receptacles that cannot be turned off by a switch or pull chain.
• Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or
explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance. The fumes can create a fire hazard or explosion.
• Do not connect or disconnect the electric plug when your hands are wet.
• Unplug the appliance or disconnect the power before cleaning or servicing. Failure to do socan
result in electrical shock or death.
• Do not attempt to repair or replace any part of your appliance unless it is specifically recommended
in this manual. All other servicing should be referred to a qualified technician.
• In the event of any damage:
o Avoid open flames and anything that creates a spark,
o Disconnect from the power source,
• Air the room in which the appliance is located for several minutes and contact theService
Department for advice.
• Replacing component parts and servicing shall be done by factory-authorized service personnel.

4
FOLLOW WARNINGS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
• Use two or more people to move and install appliance. Failure to do so can result in backor
other injuries.
• To ensure proper ventilation for your appliance, the front of the appliance must be completely
unobstructed. Choose a well-ventilated area with temperatures above 50°F (10°C) and below 89°F
(32°C).
• The appliance should not be located next to ovens, grills, or other sources of high heat.
• The appliance must be installed with all electrical, water, and drain connections inaccordance
with state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly
grounded in accordance with the National Electrical Code and local codes and ordinances, is
required.
• Do not kink or pinch the power supply cord of the appliance.
• The size of the fuse (or circuit breaker) should be 15 amperes.
• It is important that the appliance be leveled in order to work properly. You may need tomake
several adjustments to level it.
• All installations must be in accordance with local plumbing code requirements.
• Make certain that the pipes are not pinched, kinked, or damaged during installation.
• Check for leaks after connection.
• Never allow children to operate, play with or crawl inside the appliance.
• Do not use solvent-based cleaning agents or abrasives on the interior. These cleanersmay
damage or discolor the interior.
• Use this appliance only for its intended purpose as described in this User Manual.
• Keep fingers out of the “pinch point” areas. Clearances between the drawers andcabinet
are necessarily small. Be careful closing drawers when children are in the area.
• This appliance is intended to be used in household and similar applications such as
- Staff kitchen areas in shops, offices, and other working environments.
- Farm houses and by clients in hotels, motels, and other residential type environments.
- Bed and breakfast type environments.
- Catering and similar non-retail applications.
• WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer.
• WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are
of the type recommended by the manufacturer.
• If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified
persons in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
Risk of child entrapment!
Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are still dangerous,
even if they will “just sit in the garage a few days.”
Before discarding your old appliance: Take off the doors
Leave the shelves in place so that children may not easily climb inside.
- SAVE THESE INSTRUCTIONS -

5
LOCATION OF PARTS
NOTES:
• This wine cooler is designed for indoor use only.
• For ventilation purposes, the solid face of the drawer must face toward the door.
S.S. drawer
Control panel
Wine shelf
Handle
S.S. foaming door
Rolling slideway
Door gasket

6
INSTALLATION INSTRUCTIONS
Before Using your Appliance
• Remove the exterior and interior packing.
• Before connecting the appliance to the power source, let it stand upright for approximately
2 hours. This will reduce the possibility of a malfunction in the cooling system from handling
during transportation.
• Clean the interior surface with lukewarm water, using a soft cloth.
• Install the handle on the drawers if they are not already attached.
Installation of your Appliance
The appliance is designed for built-in, recessed, or free-standing installation
CAUTION: This appliance is not designed for the storage of medicine or other medical products.
• Place your appliance where the floor is strong enough to support it when it is fully loaded. To
level the appliance, adjust the front leveling legs.
• For free-standing installation, 5” (127mm) of space between the back and sides of the
appliance, and 4” (102mm) at the top, are suggested. This allows for proper air circulation.
For built-in installation, keep 2” (50mm) at the rear. Make sure the air ventilation channels at
the back of appliances are never covered or blocked in any way.
• Avoid locating the appliance in moist areas.
• Plug the appliance into an exclusive, properly grounded wall outlet.
NOTE: It is recommended that you do not install the appliance near an oven, radiator, or other
heating sources. Heat sources may increase electrical consumption, and direct sunlight may
affect the outer coating. Do not install in a location where the temperature will fall below
50°F (10°C). For best performance, do not install the appliance behind a cabinet door or
block the base grille.
Built-in Installation
CAUTION: For this model, please take into consideration the clearances required for air intake and
exhaust.
Hot air must be driven by the ventilation to the rear wall of the cooler and then expelled upwards.
The ventilation channels shall be at least 5.11”x2.36” (130x60mm) in cross-section.
Warning: to ensure proper operation, the ventilation grilles must never be obstructed or covered.

7
Ventilation channel 5.11x2.36 in. (130x60mm)
*Height needed if installing with included grille.
12” (14
3/4
)
*
11.9” (303mm)
Recess the cooler into the kitchen
cabinet and remove the S.S. drawer.
NOTE: If you are unable to cut a top
ventilation hole, install the included
ventilation grille and allow for extra
ventilation space.

8
a
b
Adjust side limited block
(b) close to the kitchen
cabinet and remove the
4 limited block covers
(a) on the left and right
inside walls of
the cooler cabinet.
c b
Drill the screw (c)
through the left and
right side holes
(b) to affix the unit to
the kitchen cabinet.

9
a. Side limited cover (2pcs on each side of cabinet) b. Side limited block (2pcs on each side of cabinet)
c. Screw
a b
Put side limited block
cover (a) and cover
the screw holes. (b)
Put the S.S. drawer back into the wine
cooler.

10
Shelves and capacity
This model includes 2 movable wine shelves, you can store the wine with or without using the wine
shelves. However, there will be different bottle capacities depending on if you use the wine shelves or not.
Wine shelf
• Without using wine shelves, it can store 8 bottles of wine with a maximum diameter of86mm
• With using wine shelves, it can store 4 bottles of wine with a maximum diameter of86mm

11
Electrical Connection
This appliance should be properly grounded for your safety. The power cord of this appliance is
equipped with a three-prong plug, which mates with standard three-prong wall outlets to minimize
the possibility of electrical shock.
Do not, under any circumstances, cut or remove the third (grounding) prong from the power cord
supplied. For personal safety, this appliance must be properly grounded. Any questions concerning
power and/or grounding should be directed toward a certified electrician or an authorized service
center.
This appliance requires a standard 115/120 Volt AC ~60Hz three-prong grounded electrical outlet.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly
grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and
obligation to have it replaced with a properly grounded 3-prong wall outlet.
To prevent accidental injury, the cord should be secured behind the appliance and not left exposed
or dangling.
The appliance should always be plugged into its own individual electrical outlet, which has a voltage
rating that matches the rating label on the appliance. This provides the best performance and
prevents overloading house wiring circuits, which could cause a fire hazard from overheating. Never
unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull it straight out
from the receptacle. Immediately repair or replace all power cords that have become frayed or
otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at
either end. When moving the appliance, be careful not to damage the power cord.
Extension Cord
Due to potential safety concerns under certain conditions, it is strongly recommended that you do
not use an extension cord with this appliance. However, if you must use an extension cord, it is
necessary that it be a UL/CUL-Listed, 3-wire grounding-type appliance extension cord that has a
grounding-type plug. The electrical rating of the cord must be 115 volts and at least 10 amperes.
WARNING
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged,
have it replaced by a qualified electrician or an authorized service center.

12
8.4” (214mm)
Installing the Stainless Steel Handle
This appliance includes one stainless steel handle
that is not required to operate the appliance. To
install the handle, follow the instructions below:
1. Remove the door gasket.
2. Install the handle with the screws provided. DO
NOT over-tighten as this will cause damage to
the stainless steel door surface.
3. Reinstall the door gasket.
Full Overlay Panel Installation
Instructions
This model is designed for a field-installed
overlay panel, which can cover the stainless
steel to give a built-in appearance. The
overlay panel and appropriate hardware are
not included with the appliance, and you must
install the panel yourself.
Please follow the instructions below for
installation:
1. Remove any items stored inside the
drawers and take the drawers out.
2.
Peel off the gasket and remove the handle
by removing the two screws that attach the
handle to the door.
3.
Drill the 6 holes shown by using a 9/50”
drill bit on the 4 sides of the drawer door
front. (Fig.2)
4.
Cut the overlay panels with 3/4” thickness
to the following dimensions: 17.87” x
11.9” (WxH).
5. If reusing the handle that came with the
appliance, drill two holes with a diameter
of 9/50” in the overlay panel.
6. If user-supplied handle will be used,
attach the handle to the overlay panels by
using the flat head screws and drive the
screws flush with the panels.
7. Attach the handle and overlay panel
together to the drawer face using 2
M4x45 screws and through the 2 existing
holes on the door face. Then attach the
overlay panel to the drawer face using 6
M4x45 screws and through 6 existing
holes inside the door groove. (Fig. 3)
8.
Attach the overlay panel to the drawer face
through the existing holes inside the door
groove, using the 6 M4x45 screws.
9.
Peel back the gaskets, then align the left
and right side channels with the tracks in the
cabinet.
6.14” (156mm)

13
OPERATING YOUR APPLIANCE
Install the appliance in a place where the ambient temperature is between 50ºF and 89ºF (10º to
32ºC), and ideally about 77ºF (25ºC). If the ambient temperature is above or below the
recommended temperatures, the interior temperatures may fluctuate, and the optimal operating
temperature may not be reached.
Control Panel
The dot will light on when Sabbath mode on These 2 dots will flash if door opening alarm is on
ON/OFF Power
To turn the appliance off, press and hold the key for 5 seconds until the temperature display
goes off.
NOTE: Pressing the ON/OFF key once can switch off the audible alarm when the alarm is on.
Setting the Temperature Control
• You can set the temperature by pressing the UP or DOWN symbol. The temperature preset at the
factory is 46°F or 8°C.
• The range of set temperatures is from 46°F to 68°F or 8°C to 20°C.
• Set the temperature by pressing the UP or DOWN symbol.
• The temperature will increase by 1°C/1ºF each time you press the UP symbol and will decrease
by 1°C/1 ºF each time you press the DOWN symbol.
• Select the temperature display in Fahrenheit or Celsius degrees. To change the temperature from
Fahrenheit to Celsius or from Celsius to Fahrenheit, press and hold the UP and DOWN symbols
for 3 seconds.
Interior Light
• The interior light will turn on/off automatically when you open or close the door.
ON/OFF
UP
DOWN

14
Sabbath Mode
• Sabbath mode is available for the observance of certain religious holidays. This mode turns off
the displays, interior light, and audible alarms and prevents them from turning on again. Normal
cooling operations will still take place.
• To initiate Sabbath mode, press the ON/OFF and UP symbols at the same time and hold for 3
seconds. The dot in the upper left corner of the LED screen will on and confirm that Sabbath
mode is ON.
• Sabbath mode can be canceled by repeating the process above. Sabbath Mode will
automatically turn off after 24 hours. If the power goes off, when it is recovered, Sabbath Mode
will turn off.
Defrosting
Under normal operating conditions, the appliance does not require manual defrosting.
Warning System
Door Opening Alarm
If the door has been left open for more than 5 minutes, the 2 dots on the screen will flash and beep
3 times every 5 seconds. Press any key or close the door to stop the alarm.

15
CARE AND MAINTENANCE
Cleaning your Appliance
• Turn off the power, unplug the appliance, and remove all items.
• Wash the inside surfaces with a solution of warm water and baking soda (a quart of water to
about 2 tablespoons of baking soda).
• Wring excess water out of the sponge or cloth when cleaning the area where the controls are
located, or near any electrical parts.
• Wash the outside cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry
with a clean, soft cloth.
• Use an approved stainless steel cleaner to clean the doors and handle. Do not use steel wool
or a steel brush on the stainless steel.
CAUTION: Failure to unplug the appliance before cleaning could result in electrical shock or other
personal injuries.
Power Failure
Most power failures are corrected within a few hours and should not affect the temperature of your
appliance if you minimize the number of times the drawers are opened. If the power is going to be off
for a longer period of time, take the proper steps to protect the contents.
Vacations
• Short vacations: Leave the appliance operating during vacations of less than three weeks.
• Long vacations: If the appliance will not be used for several months, remove all items, and turn
off the appliance. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave
the drawers slightly open.
Moving your Appliance
1. Remove all stored items.
2. Securely tape down all loose parts (baskets, dividers) inside your appliance.
3. Turn the adjustable legs up to the base to avoid damage.
4. Tape the drawers shut.
5. Be sure the appliance stays secure and in an upright position during transportation. Also,
protect the outside of the appliance with a blanket or similar item.
Energy-Saving Tips
• The appliance should be located in the coolest area of the room, away from heat-producing
appliances, and out of direct sunlight.
• Ensure that the appliance is adequately ventilated. Never cover air vents.
• Do not keep the drawers open longer than necessary.
• Let hot foods cool to room temperature before placing them in the appliance.
• Be sure to wrap foods properly, and wipe containers dry before placing them in the appliance.
This reduces frost build-up inside the appliance.
• Appliance bins and baskets should not be lined with aluminum foil, wax paper, or paper towels.
Liners interfere with cold air circulation, making the appliance lessefficient.

16
TROUBLESHOOTING
You can solve many common problems easily, possibly saving you the cost of a service call. Try the
suggestions below to see if you can solve the problem before calling the servicer.
PROBLEM
POSSIBLE CAUSE
REMEDY
The
appliance
does not
operate
 The appliance is not connected to a power
source
 The appliance is turned off
 A triple circuit breaker or blown fuse
 Connect the appliance to a power source
 Turn on the appliance
 Turn the circuit breaker on or replace the
fuse
The
appliance is
not cold
enough
 The temperature is not set correctly
 The drawer is opened too often
 The drawer was not closed completely
 The drawer is not hermetically sealed
 The condenser is too dirty
 The ventilation opening is blocked or is too
dusty
 Check the set temperature. The ambient
temperature could require a lower
temperature setting, set a lower temperature
 Do not open the drawer more often than
necessary
 Close the drawer properly
 Check the seal and clean or replace it
 Clean the condenser, when necessary
 Clear any obstructions and wipe off the dust.
The
appliance
turns itself on
and off
frequently
 The ambient room temperature is higher
than average
 A large amount of food has been added to
the appliance
 The drawer is opened too often
 The drawer is not closed completely
 The drawer gasket does not seal properly
 Place the appliance in a location with a
cooler ambient temperature
 Leave the appliance to work until the set
temperature has been reached
 Do not open the drawer more often than
necessary
 Close the drawer properly
 Check the drawer seal and clean it or
replace it.
The light
does not
work

The appliance is not connected to a power
supply
 A tripped circuit breaker or a blown fuse
 The light is switched off on the control
panel
 Connect the appliance
 Turn the circuit breaker on or replace the
fuse
 Switch on the light
Vibration
The appliance is not properly leveled
Level the appliance using the adjustable feet
The
appliance
makes too
much noise
The appliance is not properly leveled
Level the appliance with the adjustable feet
The drawer
will not close
properly
 The appliance is not properly leveled
 The gasket is dirty
 The baskets or bins are out of position
 Level the appliance with the adjustable feet
 Clean the drawer gaskets
 Check the baskets and bins and refit them
correctly.
Display “LL,”
“EE”
 “LL” indicates the temperature sensor open
circuit
 “EE” indicates the temperature sensor
short circuit
Call for service.
If you've checked the table above and find that you still need help with your appliance, call our Customer
Service facility at 800-932-4267 or visit summitappliance.com/support between 9:00 AM and 5:00 PM ET. We
will do our best to answer your questions.

17
LIMITED WARRANTY
ONE-YEAR LIMITED WARRANTY
Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated
and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-
specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a
designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing
defects. Plastic parts, shelves and cabinets are warranted to be manufactured to commercially acceptable
standards and are not covered from damage during handling or breakage.
ITEMS WARRANTOR WILL NOT PAY FOR:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to
replace or repair fuses or to correct wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as
filters) are excluded from warranty coverage.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products not
approved by warrantor.
4. Replacement parts or repair labor costs for appliances operated outside the United States.
5. Repairs to parts or systems resulting from unauthorized modifications made to theappliance.
6. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.
WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR
LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO
THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
Felix Storch, Inc.
An ISO 9001:2015 registered company
770 Garrison Ave
Bronx, New York 10474
www.summitappliance.com
For parts and accessory ordering,
troubleshooting, and helpful hints, visit:
www.summitappliance.com/support
WARNING: This product can expose you to chemicals including Nickel (Metallic) which is
known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov
Note: Nickel is a component in all stainless steel and some other metallic compositions.

18
SÉCURITÉ DE L'APPAREIL
Votre sécurité et celle des autres sont très importantes.
Nous avons fourni de nombreux messages de sécurité importants dans ce manuel et sur votre appareil. Lisez et respectez
toujours tous les messages de sécurité.
C’est le symbole d'alerte de sécurité. Le symbole vous avertit des dangers qui peuvent vous
tuer ou vous blesser ainsi que d'autres personnes. Tous les messages de sécurité suivront
le symbole d'alerte de sécurité et le mot DANGER ou AVERTISSEMENT.
DANGER signifie que le non-respect de cette déclaration de
sécurité peut entraîner des blessures graves ou la mort.
WARNING ou AVERTISSEMENT signifie que le
non-respect de cette déclaration de sécurité peut
entraîner des dommages importants au produit,
des blessures graves ou la mort.
Tous les messages de sécurité vous avertiront du danger, vous indiqueront comment réduire les risques de blessure et
vous indiqueront ce qui peut arriver si les instructions ne sont pas suivies.
GARANTIES IMPORTANTES
Avant d'utiliser l'appareil, il doit être correctement positionné et installé comme décrit dans ce manuel,
alors lisez attentivement le manuel. Pour réduire le risque d'incendie, d'électrocution ou de blessure lors
de l'utilisation de l'appareil, suivez les précautions de base, y compris les suivantes :
• Branchez dans une prise à 3 broches mise à la terre, ne retirez pas la broche de mise à la terre, n'utilisez pas d'adaptateur
et n'utilisez pas de rallonge.
• Remplacez tous les panneaux avant d'utiliser.
• Il est recommandé de prévoir un circuit séparé desservant uniquement votre appareil. Utilisez des prises qui ne peuvent pas
être fermées par un interrupteur ou une chaînette.
• Ne nettoyez jamais les pièces de l'appareil avec des liquides inflammables. Ces fumées peuvent créer un risque d'incendie
ou d'explosion. Et ne stockez pas ou n'utilisez pas d'essence ou d'autres vapeurs et liquides inflammables à proximité de cet
appareil ou de tout autre appareil. Les fumées peuvent créer un risque d'incendie ou d'explosion.
• Ne branchez ou ne débranchez pas la prise électrique lorsque vos mains sont mouillées.
• Débranchez l'appareil ou coupez l'alimentation avant le nettoyage ou l'entretien. Le non-respect de cette consigne peut
entraîner un choc électrique ou la mort.
• N'essayez pas de réparer ou de remplacer une pièce de votre appareil à moins que cela ne soit spécifiquement
recommandé dans ce manuel. Toute autre réparation doit être confiée à un technicien qualifié.
• En cas de dommage :
o Évitez les flammes nues et tout ce qui crée une étincelle,
o Débrancher de la source d'alimentation,
o Aérez la pièce dans laquelle se trouve l'appareil pendant quelques minutes et contactez le service après-vente pour
obtenir des conseils
• Le remplacement des composants et l'entretien doivent être effectués par du personnel d'entretien autorisé par
l'usine.

19
SUIVEZ LES AVERTISSEMENTS CI-DESSOUS UNIQUEMENT LORSQU'APPLICABLES À VOTRE MODÈLE
• Utilisez deux personnes ou plus pour déplacer et installer l'appareil. Le non-respect de cette consigne peut
entraîner des blessures au dos ou autres.
• Pour assurer une bonne ventilation de votre appareil, la face avant de l'appareil doit être complètement dégagée.
Choisissez un endroit bien aéré avec des températures supérieures à 10 °C (50 °F) et inférieures à 38 °C (100
°F).
• L'appareil ne doit pas être placé à côté de fours, de grils ou d'autres sources de chaleur élevée.
• L'appareil doit être installé avec toutes les connexions électriques, d'eau et de vidange conformément aux codes
nationaux et locaux. Une alimentation électrique standard (115 V CA uniquement, 60 Hz), correctement mise à la
terre conformément au Code national de l'électricité et aux codes et ordonnances locaux, est requise.
• Ne pas plier ni pincer le cordon d'alimentation de l'appareil.
• La taille du fusible (ou du disjoncteur) doit être de 15 ampères.
• Il est important que l'appareil soit de niveau pour fonctionner correctement. Vous devrez peut-être faire plusieurs
ajustements pour le mettre à niveau.
• Toutes les installations doivent être conformes aux exigences du code de plomberie local.
• Assurez-vous que les tuyaux ne sont pas pincés, pliés ou endommagés lors de l'installation.
• Vérifiez les fuites après le raccordement.
• Ne laissez jamais les enfants utiliser, jouer avec ou ramper à l'intérieur de l'appareil.
• N'utilisez pas de produits de nettoyage à base de solvants ni d'abrasifs à l'intérieur. Ces nettoyants peuvent
endommager ou décolorer l'intérieur.
• Utilisez cet appareil uniquement aux fins pour lesquelles il a été conçu, tel que décrit dans ce manuel d'utilisation.
• Gardez les doigts hors des zones de « point de pincement ». Les dégagements entre les tiroirs et le meuble sont
nécessairement faibles. Faites attention en fermant les tiroirs lorsque des enfants se trouvent à proximité.
• • Cet appareil est destiné à être utilisé dans des applications domestiques et similaires telles que
• - Zones de cuisine du personnel dans les magasins, bureaux et autres environnements de travail ;
• - Maisons de ferme et par des clients dans des hôtels, des motels et d'autres environnements de type
résidentiel ;
• - Environnements de type chambres d’hôtes ;
• - Restauration et applications similaires non commerciales.
• • AVERTISSEMENT : N'utilisez pas d'appareils mécaniques ou d'autres moyens pour accélérer le processus de
dégivrage, autres que ceux recommandés par le fabricant.
• • AVERTISSEMENT : N'utilisez pas d'appareils électriques à l'intérieur des compartiments de conservation des
aliments de l'appareil, à moins qu'ils ne soient du type recommandé par le fabricant.
• • Si le CORDON D'ALIMENTATION est endommagé, il doit être remplacé par le fabricant, son agent de service
ou des personnes de qualification similaire afin d'éviter tout danger.
• • Cet appareil n'est pas destiné à être utilisé par des personnes (y compris des enfants) ayant des capacités
physiques, sensorielles ou mentales réduites, ou un manque d'expérience et de connaissances, à moins
qu'elles n'aient reçu une supervision ou des instructions concernant l'utilisation de l'appareil par une personne
responsable de leur sécurité.
• • Les enfants doivent être surveillés pour s'assurer qu'ils ne jouent pas avec l'appareil.
Risque de piégeage d’enfants !
Le piégeage et la suffocation des enfants ne sont pas des problèmes du passé. Les appareils mis
au rebut ou abandonnés sont toujours dangereux, même s'ils « restent dans le garage quelques
jours ».
Avant de vous débarrasser de votre ancien appareil : Enlevez les portes
Laissez les étagères en place afin que les enfants ne puissent pas grimper facilement à l'intérieur.
- CONSERVEZ CES INSTRUCTIONS –

20
EMPLACEMENT DES PIÈCES
Panneau de
commande
Gérer
Joint de porte
Tiroir inox
Étagère à vin
Glissière roulant
Porte moussante SS
REMARQUES
:
Ce refroidisseur à vin est conçu pour une utilisation en intérieur uniquement.
Pour des raisons de ventilation, la face pleine du tiroir doit être orientée vers la porte.