Sunjoy Grand Summer User manual

1-4
Owner’s manual
Grand Summer Gazebo G-GZ039PST-2
1. WARNING
1. When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and use.
2. Some parts may contain sharp edges, wear protective gloves if necessary. At least two or more
people are recommended for safe assembly.
3. Keep all children and pets away from assembly area.
4. Begin assembly not less than 6 feet from any obstruction such as fence, garage,house, overhanging
branches, laundry line or electrical wires.
5. Install on level ground. This gazebo cannot be permanently staked or attached to concrete floor or
platform. This gazebo is intended for decorative and sunshade purposes only and is not meant to
withstand inclement weather including high winds, rain and snow. Gazebo fabric is water resistant,
not water proof and may leak during exposure to precipitation.
6. Check all nuts and bolts for tightness before and during usage.
7. Warning: keep all flame and heat sources away from this gazebo fabric. This gazebo is made with
fabric that meets cpai-84 specifications for flame resistance. It is not fire proof. The fabric will burn if
left in continuous contact with any flame source. The application of any foreign substance to the
gazebo fabric may render the flame-resistant properties ineffective.

2-4
No.
2. Part List
Part
Qty
No.
Part
Qty
A
Big Screen
4
O
Shelf
4
B
Small Screen
4
P
3-way Fitting
4
C
Pole (78.34in)
2
Q
4-way Fitting
4
D
Pole (51.77in)
2
R
Screw M6*30
TBZ0010630HQ
12
E
Pole (50.2in)
2
S
Screw M6*16
TBZ0010616HQ
16
F
Pole (67.32in)
4
T
Snap Link (Pre assembled)
20
G
Pole (55.51in)
2
U
Small Canopy
1
H
Pole (52.36in)
2
V
Big Canopy
1
I
Pole (57.48in)
4
W
Wrench
1
J
Pole (69.29in)
4
X
Washer (M6) TBZ10406HQ
28
K
Arm Connector
(16.14in)
2
Y
Stake （TBZ10706250XQ）
16
L
Arm Connector
(34.25in)
2
Z
Paint Bottle
1
M
Extreme Pole
(29.53in)
4
Y1
Mosquito Net Connector
1
N
Extreme top
connector
1
Z1
Mosquito Net
1
W1
Washer(M5)
TBZ10405HQ
30
X1
Screw M5*16
TBZ0010516HQ
30
A
D
B
AP
F
Fig.1
Fig.2
Fig.4
Fig.3
Y
AB
C
I
D
QL
K
M
H
G
F
PE
N
J J
Y1
Y1 J
J
I
A
B
Fig.5
Y1 I
G
X1
X
X1
X1
W1
W1
X1
X1
W1
S
W1 W1
X1
X
R
W1
C
H

3-4
3. Assembly Instructions
Step 1 Lay parts on ground as shown.
Step 2 Attachbigscreen(A)to smallscreen(B)usingscrew(R)andwasher(X).<Fig.1>Repeatthisprocedurefor
other screens. Then place these 4pcs completed screens (A&B) upright and set them at four corners to
form square approximately 12 x 10 feet across.
Step 3 Attach3-way fittings(P) to completed screens (A&B) using screws (X1) and washers (W1).<Fig. 4> Repeat
this procedure for other screens.
Step 4 Connect 2 completed screens (A&B) with pole (C) by screws (S)and washers (X) in the side 10 feet length.
Repeat this procedurefor opposite side. <Fig. 2>
Step 5 Insert pole (E)into pole (D), fastened by screw (X1) and washer (W1). <Fig. 3> Then attach this connected
pole (D&E) into 2 completed screens (A&B) by screw (S) and washer (X). Repeat this procedure for
opposite side. <Fig. 2>
Step 6 Insert one end of pole (I) into 3-way fitting (P), the other end into mosquitonet connector (Y1) as shown in
Fig. 4 & 5. Repeat this procedure for opposite side.
Step 7 Insert one end of pole (J) into 3-way fitting (P),the other end into mosquito net connector (Y1)as shown in
Fig. 4 & 3.Repeat this procedure for opposite side.
Step 8 Insertarmconnector(L)andarmconnector (K) into 4-wayfitting (Q), fasten by screw (X1)and washer(W1)
to form a square as figure.
Step9 Insertoneend ofpole(F)into3-wayfitting(P),theotherend into4-way fitting(Q).Repeatthisprocedurefor
opposite side.
Step10 Insert one end of pole (G) into arm connector (K), the other end into mosquito net connector (Y1) and
fasten it together with mosquito net connector (Y1) and pole (C) by screw (X1) and washer (W1).
<Fig. 5> Repeat this procedure for opposite side.
Step11 Insert one end of pole (H) into arm connector (L), fasten the other end with mosquito net connector (Y1)
and connected poles (D & E) together by screw (X1) and washer (W1). <Fig. 3> Repeat this procedure for
opposite side.
Step12 Put big canopy (V) over the frame, and fit it into frame.
Step13 Insertpole(M)intoextremeconnector(N).Putsmallcanopy(U)overtheextremeframe,fitcanopycorners
tothetoppartofextremepoles(M),andtheninsertthewholecompletedextremetopinto4-wayfitting(Q).
Step14 Put shelf (O) into completed screens (A& B). Hang mosquito net (Z1) up to the top part of poles (I) and

4-4
poles (J)
Step15 Secure the gazeboto the ground with stakes(Y).
Please do not return this product to the store. For technical assistance on assembly or replacement parts, call
Sunjoy Industries at [phone] from 8:30 AM to 5:30 PM EST Monday to Friday; or For expedited replacement
parts order, fax the attached completed customer service replacement form to 740 283 3549; or
email [e-mail] for assistance.
U
V
O