Sunjoy L-GZ798PST-E User manual

ASSEMBLY INSTRUCTIONS
ITEM# L-GZ798PST-E
IMPORTANT
Production Number: xxxxxxxxxx
Thank you very much for choosing Sunjoy Group.
Please take time to read these instructions thoroughly and follow each step carefully for safe and easy
operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. You can call us toll-free
at 1-866-578-6569 anytime 24 hours / 7 days a week. For further assistance , please write to us at
[email protected]

SAFETY INFORMATION:
Please read and understand this entire manual before attempting to assemble or install the
product.
When installing and assembling the item, it is recommended two or more adults are
involved.
This product is intended for outdoor use only and should be placed on flat, horizontal
ground.
Ensure enough clearance around the product.
Do not use the unit during an electrical storm, as there is a remote chance of getting
struck by lightning.
Do not climb on top of the item. Falling off it can result in serious injury, possibly even
death.
Never barbecue underthis item or use lanterns that contain open flames.
This package contains small items and plastic bags that should be kept away from
children.
Ensure all connectors and poles are firmly secured in position. It is important to do so
before use to avoid collapsing or damage to the item, which could also result in injury.
Center hook’s maximum weight capacity is 26 lbs.
WARNING:
Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that
meets CPAI-84 specifications for flame resistance. It is not fire proof. The fabric will burn if left
in continuous contact with any flame source. The application of any foreign substance to the
tent fabric may render the flame-resistant properties ineffective. Remove the roof during
severe weather conditions such as sustained strong winds, hurricanes, tropical downpours
and snow. The manufacturer or retailer is not liable for any loss of the product or other items
due tothe failure totake down the item during any inclement weather.
PREPARATION:
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 30 minutes
No Tools Required for Assembly.

P11149B01106
P11064C01106
P11065C01106
P11066C01106
P11067C01106
P10308B01106
P10480A01106
P10481A01106
P10482A01106
P10483A01106
P10309B01106
P10310B01106
P10112B01106
P12601C01106
P10252A01106
P10113B01106
P11726A01106
P00151B06011
Corner Panel
Long Cross Beam 1
Long Cross Beam 2
Short Cross Beam 1
Short Cross Beam 2
Oblique Beam
Long Middle Beam
Short Middle Beam
Bottom Long Middle Beam
Bottom Short Middle
Beam
Bottom Oblique Beam 1
Bottom Oblique Beam 2
Big Roof Connector
Hook
Small Roof Oblique Beam
Small Roof Connector
Corner Shelf
Big Canopy
A
B
C
D
E
F
G1
G2
H
I
J1
J2
K
L
M
N
O
P
4
2
2
2
2
4
2
2
2
2
2
2
1
1
4
1
4
1
Parts List
Part NO. QTY
CS NO. Image
Description

Fig.1: Spread the Corner Panel (A) on the ground
Fig.2: Insert Long & Short Cross Beam 2(C&E) into Long & Short Cross Beam 1(B&D),
tighten with
Knob (S).
Fig.3: Insert the assembled Cross Beam (B, C, D, E) into Corner Panel (A)
Hardware Pack 1
Small Canopy Q 1
Mosquito netting R 1
Knob S 12
P00152B06011
P00332B01903
P90804A07001
Part NO. QTY
CS NO. Image
Description

Fig.4: Insert the Oblique Beam (F) into Bottom Oblique Beam (J1&J2)
Fig.5: Insert the Big Roof Connector (K) into another side of the Oblique Beam (F)
Fig.6: Insert the assembled Bottom Oblique Beam (J1&J2) into the Corner Panel (A)
Fig.7: Insert the Middle Beam （G1&G2 ）into the Bottom Middle Beam (H&I)
Hardware Pack 2
Fig.8: Insert the Long Middle Beam (G1) and Short Middle Beam (G2) into the big Roof Connector (K),
attached the Hook (L) on the big Roof Connector (K)
Fig.9: Insert the assembled bottom middle beams (H&I) into the Cross Beam (E&C), tighten with Knob (S),
place the Big Canopy (P) to the roof, do not spread it.
Fig.10: Insert the Small Roof Oblique Beam (M) into the Small Roof Connector (N)
Fig.11: Attach Small Canopy (Q) to the small roof along the Small Roof Oblique Beam (M), aligning the corners
and stretching it to fit.
Fig.12: Insert the Small Roof Oblique Beam (M)
into the Oblique Beam (F)

AA Plastic Ring P90701B07007
P12406C01001
52 PCS
BB Φ6X180MM“7”Stake 16 PCS
Hardware Pack 3
Fig.13: Spread Large Canopy (P) to the roof along the Bottom Oblique Beam (J1&J2), aligning the corners
and stretching it to fit.
Fig.14: Place Corner Shelves (O) onto Corner Panels (A) as desired.
Fig.15: Hang Mosquito netting (R) to the Cross Beams (B, C, D, E), by using Plastic Ring (AA).
Fig.16: Secure the assembled gazebo to lawn with stakes (BB) through the bottom of corner panels (A ).
Part NO.
QTY
CS NO. ImageDescription

Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it
from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once these protective
coatings are scratched. This is not a defect and thus not covered by the warranty.
To minimize this condition, we recommend care when assembling & handling the product to prevent scratching
the paint. Should any scratching or damage occur, we recommend immediate touch-up with rust inhibiting
paint.
Surface rust can also be easily removed with a light application
of any rust removing solution, we also
If
no measure is taken to prevent this, the
oxidation may start dripping on to deck or patio and caused damaging stains, which may be difficult to
remove. This can be prevented if the above-mentioned measures
are taken to keep the product from oxidizing.
Limited Manufacturer’s Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal, residential
purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1) year. We
don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for
assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered.
Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser
and is non-transferable. Any replacement of warranted items will be in the original style and color, or a similar
style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions
or limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives
you specific rights, and you may also have other rights, which vary from state to state.
Made in China
recommend WD-40, which is readilyavailable in all majorstores.