Sunlight Supply TITAN CONTROLS KRONUS 2 User manual

Kronus 2TM
Temperature, Humidity and CO² Controller
Instruction Manual
VANCOUVER, WASHINGTON U.S.A.
VANCOUVER, WASHINGTON U.S.A.
www.titancontrols.net
www.titancontrols.net
Notes:
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
________________________________________________
1 Square = 1 Foot
®

Kronus 2
• Warnings & Cautions
• Kronus 2- Temperature, Humidity and CO2 Controller
• Instructions for Operation
• Troubleshooting Tips
• Controller Specifications
• Installation Example
• Warranty Information
• Service and Repair Program
Warnings & Cautions
• Read all instructions before operating controller.
• Do not put your controller in an area where it can get wet or sprayed.
• Mount your controller securely to the wall using hardware provided.
• When using “bug bombs” in area, cover controller completely to avoid corrosion.
• There are no serviceable parts in controller. Do not attempt to repair the unit.
• Breaking “warranty” seal will void your warranty.
• Do not put paperclips, tools, etc. into unit. Possible electrocution may occur.
• Plug controller into surge protector to avoid potential damage to the unit.
• Make sure to verify your power source prior to plugging controller into outlet.
• Check that all equipment that will be activated by this controller is the proper voltage.
• Verify that your equipment does not exceed a total of 15 amps.
• This controller is designed for inside use only.
• Avoid placing the controller near heat generating sources.
• Use caution when operating controller in extremely humid environments.
• Do not use controller for purposes other than the unit was designed to function
• Use controller within defined environmental specifications.
• Ask your Dealer for tips and techniques regarding the use of this controller.
• Be conscientious when disposing of any products.
• Enjoy your Titan Controls environmental controller for years to come!
WARRANTY SERVICE
If after reviewing the troubleshooting tips the unit will still not work, you should return it to the
Dealer where you purchased it. They will be able to further evaluate the unit and test its various
components and quite possibly will be able to identify and/or fix any problems. If the Dealer is
unable to fix the unit, they will return it to us for factory repair.
If there are no Dealers in your area, you may contact us directly for technical support. If we
cannot help you resolve the problem over the phone, we will issue you a RMA number (Return
Merchandise Authorization) authorizing you to return the unit to us for factory reconditioning (if the
unit is under warranty). Contact the number below for a RMA and shipping address. Complete the
form below and include it with your unit. Also please write the RMA # on the outside of the box.
Please package the unit in its original packaging. If it is damaged in shipment we cannot be
responsible.
Once we receive the unit back, we will repair it within 48 hours (business) and return it to you
freight prepaid via FedEx or UPS ground shipment.
Include the following if returning directly to Titan Controls
• Proof of purchase • This completed form • RMA # on the outside of the box
Return Merchandise Authorization Number (Required
Company Name: ____________________________________________________________________________________
Contact Name: _____________________________________________________________________________________
Address: __________________________________________________________________________________________
____________________________________________________________________________________________________
Phone #: ___________________________________________________________________________________________
Email address: _______________________________________________________________________________
What is the nature of the problem?
______________________________________
___________________________________________________________
___________________________________________________________
___________________________________________________________
___________________________________________________________
_______________________________________________________
Send to your nearest location – shipping address will be given when the RMA # is issued:
www.titancontrols.net
For technical assistance call us at 1-888-80-Titan or 1-888-808-4826.
®

Kronus 2 – Temperature, Humidty
and CO²Controller
The Kronus 2 is used to maintain the temperature, humidity and CO2 in your growing environ-
ment. Both the temperature and humidity can be adjusted by setting the dials on the front of the
controller to your preferred settings. If the temperature or humidity exceeds the predetermined
settings then the controller begins a ten (10) minute “environmental polling process”. If after ten
(10) minutes the temperature or humidity still exceeds the settings, then an exhaust fan is activated
and will run until the temperature or humidity is lower than the set point. After the temperature or
humidity has lowered below the selected temperature or humidity level, the ‘CO2 On’ green LED
is lit and your CO2 system is reactivated. This innovative function serves two purposes: One, this
allows maximum CO2 coverage with minimum CO2 waste and two, your exhaust fan is working
only when it is required, saving power and wear & tear on your equipment. There is a convenient
“Grow Zone” section on each dial to give the grower an easy to use reference point for plant
success. Controllers created for our industry, by our industry.
The Kronus 2 allows up to 15 Amps of maximum capacity on a standard 120 Volt circuit. The Kronus
2 is built with the highest quality components to provide the user with years of trouble free service.
Instructions for Operation
• Securely mount your Kronus 2 in your grow area and away from any
moisture, spray, pesticides, etc.
• Plug your fan into the “Exhaust Fan Output’ outlet.
• Turn the fan ‘ON’ to the highest setting possible.
• Plug your CO2 Controller (Atlas 1) or a short cycle timer (Apollo 1) into the “CO2 Output” outlet.
• Then, plug your CO2 Generator or CO2 Regulator/Tank into the controller/short
cycle timer (See Installation Example section for more information)
• Set the ‘Temperature’ and ‘Humidity’ dials at the preferred temperature and
humidity levels for your garden.
• Place the remote sensor in the grow area up to 25 feet away from the Kronus 2 at
plant canopy height.
• After the ‘CO2 Output’ is disabled, the Kronus 2 begins a ten (10) minute delay process
by polling the temperature and humidity levels to confirm that ventilation is still required.
If confirmed after 10 minutes, then ventilation process begins and continues until the
temperature and humidity levels are lowered to the dials settings. However, if the temperature
and humidity drop to within the dial settings during the ten (10) minute period, then the
‘CO2 Output’ outlet is reactivated and resumes normal functioning.
• Plug the Kronus 2 into a maximum 120 Volt – 15 Amp outlet.
• Use of a surge protection device is recommended to protect your Kronus 2 from potential
damage.
• Turn the Kronus 2 power switch to the ‘ON’ position.
• Your Kronus 2 will now control your exhaust fan and CO2 equipment at the desired settings.
Warranty Information
• Titan Controls warrants the original purchase of this product against defects in material and
workmanship under normal use for three (3) years from the date of purchase.
• During the warranty period, Titan Controls will, at our option, and without charge, repair or
replace this product if the controller or any of its components fail or malfunction.
• All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA)
number prior to any service of the product.
• This warranty is expressly in lieu of all other warranties, expressed or implied, including
the warranties of merchantability and fitness for use and of all other obligations or liabilities
on the part of the seller.
• This warranty shall not apply to this product or any part thereof which had been damaged by
accident, abuse, misuse, modification, negligence, alteration or misapplication.
• Controllers with serial numbers or date tags that have been removed, altered or obliterated;
broken seals or that show evidence of tampering; mismatched board serial numbers or
nonconforming parts, are excluded from coverage.
• Titan Controls makes no warranty whatsoever in respect to accessories or parts not
supplied by Titan Controls.
• Monetary refunds of the warranty will not be given.
• The Buyer assumes all responsibility regarding the use & installation of this controller.
• All warranty service is provided through the factory or an authorized service representative.
• This warranty shall apply only to the United States, including Alaska, Hawaii and
territories of the United States.
• Defective controllers need to be returned with the “proof of purchase/receipt”.
• For additional warranty information, contact a Titan Controls Technical Service
Representative or your Dealer.
• NOTE: Titan Controls is a manufacturer of environmental controls. All sales offerings to the
public are done through a nationwide group of Dealers. No sales offerings will be made
directly to the general public.
Service and Repair Program
• For all service and repairs please contact one of our Technical Service Representatives for a
Return Merchandise Authorization (RMA) number.
• All factory service & repairs will be completed within 48 hours of receipt of controller and after
authorization by customer for repairs.
• Titan Controls will, at its discretion, repair or replace the controller.
• Factory calibration services are available for all Titan Controls. Returning Units: Please contact
your retail store for returns.

Troubleshooting Tips
If the Kronus 2 is not performing as expected, try the following:
a. Make sure that the power switch is lit and in the ‘ON’ position.
b. Confirm that your power source is active by using a voltage test meter and
providing 120 Volts to the controller.
c.Validate the voltage outputs of the Kronus 2 are active by adjusting the dial to the lowest
settings and using a voltage test meter, fan or 120 Volt light to verify power is flowing through
the controller.
d. Ensure that the exhaust fan is ‘ON’ and set to the maximum level.
e. Verify that the Kronus 2 is set at the proper levels to activate and deactivate equipment.
f. If your ventilation equipment does not turn off, verify that your exhaust fan is the
correct size for your grow area. Increase size of fan, (if necessary).
g. Inspect the remote sensor and make sure it is dry. If not, allow to dry prior to activating.
h. Check the remote sensor to verify that the green LED is steady ‘ON’ and NOT blinking.
i. If the green ‘ON’ LED on the Kronus Temperature and Humidity sensor is blinking, there is a
communication problem between the sensor and the controller. Contact your Dealer or our
Technical Service Representative to help you.
j. If you are still having problems with your Kronus 2, please contact our Technical Service
Representative to assist you further.
Controller Specifications:
• Size = 9.5"H x 8.5"W x 2.5"D
• Weight = 3 lbs.
• Input Voltage = 120 Volts/AC
• Output Voltage = 120 Volts/AC
• Maximum Amperage = 15 Amps
• Operating Hertz = 60 Hz
• Minimum/Maximum Humidity Control Levels = 40% to 90% (non-condensing)
• Humidity Accuracy = ±5% of desired setting
• Minimum/Maximum Temperature Control Levels = 45° to 95°F (7° to 35°C)
• Temperature Accuracy = ± 2°F of desired setting
• RoHS compliant = Yes
• Cord set = 6 feet - 14/4 SWJ
• Remote Sensor Cable = 25 feet/Cat 5e/RJ45
• Storage Temperature = 32° to 135°F (0 to 58°C)
• Operating Temperature = 45° to 95°F (7 to 35°C)
Installation Example
Kronus 2
120 Volt
Power in
Exhaust Fan
Remote
Sensor
CO2
Generator
CO2
Tank
OR
Kronus
Sensor
Atlas 1
CO² Monitor
and Controller
Controlling a CO² Tank or CO² Generator & Exhaust Fan