Sunny Health & Fitness SF-B1001 User manual

I
IN ND DO OO OR R C CY YC CL LI IN NG G B BI IK KE E
S
SF F- -B B1 10 00 01 1
O
OW WN NE ER R’ ’S S M MA AN NU UA AL L
For Customer Service, please contact: [email protected]
The specifications of this product may
vary from this photo and are subject to
change without notice.

1
IMPORTANT SAFETY NOTICE
Make sure you fully understand the following precautions before assembling and operating the
machine:
1. Once fully assembled, please check that all hardware parts such as bolts, nuts and washers are
positioned and secured firmly.
2. Please check regularly that the safety chain guard that protects the moving parts of the
machine is secured and in good order.
3. Please always check the seat post, seat slider, pedals and handlebar are secured firmly before
getting on the bike.
4. To lubricate all moving parts annually is recommended.
5. In order to avoid entangling in any moving parts; do not wear loose clothing.
6. Do not remove feet from the pedals while they are in motion.
7. Always wear shoes when using the machine.
8. Dry the bike after each use to remove sweat and moisture. Wipe the machine with a damp cloth,
water and mild soap. Do not use a petroleum-based solvent to clean the machine, in order not to
damage the finish.
9. Please keep children away from the bike while it is in use. Do not allow children to use the bike.
This bike is designed for adults, not children.
10. Do not dismount the bike until the pedals have stopped moving completely.
11. Stop exercise immediately if you feel any of the following symptoms: nausea, shortness of
breath, faint, headache, pain, tightness in your chest or any discomfort.
12. Do not place fingers or any other objects into the moving parts of the bike.
13. Prior to any exercise, consult with your physician first to establish the exercise frequency, time
and intensity appropriate for your particular age and conditioning.
14. After exercising, please push down the tension controller to increase resistance so that the
pedals will not rotate freely and possibly hurt someone.
15. Maximum user’s weight is 220LB.
16. This equipment is designed for indoor and home use only, not intended for commercial use.

2
EXPLODED DIAGRAM

3
PARTS LIST
NOTE:Most of the listed assembly hardware has been packaged separately, but
some hardware items have been preinstalled in the identified assembly parts. In
these instances, simply remove and reinstall the hardware as assembly is
required.
Please reference the individual assembly steps and make note of all preinstalled
hardware. Prior to assembly of this product, remove all components from the
package and verify all the listed parts are supplied.
Part No. Description Qty Part No. Description Qty
1 Main frame 1 16 Square cap 1
2 Front stabilizer 1 17
Phillips tapping 2
3 Rear stabilizer 1 18 Hex nut M10 4
4 Handlebar 1 19
Water bottle
hld
1
5 Seat post 1 20 Nylon nut 2
6 Seat slider 1 21 Foam grip 2
7 Saddle 1 22 End cap 2
8 Pop-pin knob 3 23 Allen bolt 4
9L/R Pedal 1each 24 Spring washer 4
10L/R Crank 1each 25 A/B Handlebar cover 1each
11 Leveler feet 4 26 Handlebar post 1
12 Oblong cap 4 27 Phillips screw 4
13 Flat washer 10 28 Allen bolt 2
14 Allen bolt 4 29 Roller 2
15 Plastic bushing 3

4
ASSEMBLY INSTRUCTIONS
Step A:
Install the Front stabilizer (2) and Rear
stabilizer (3) to the Main frame (1) with
the Bolts (14) and Flat washers (13).
Please make sure that the Leveler feet
are on the bottom and the
transportation wheels are facing up and
towards the front of the bike.
Attach the Water bottle holder (19) to
the frame with the Screws (17).
Note: The Leveler feet (11) under the
stabilizers can be adjusted to keep the
equipment stable.
Step B:
Attach the Handlebar (4) to the Handlebar post (26), secured
with Allen bolts (23), Flat washers (13) and Spring washers (24).
Set the lower Handlebar cover (25B) on the square tube of the
Handlebar post (26) in alignment with the four grooves on the
mouth of the lower Handlebar cover (25B). When the lower
Handlebar cover (25B) slides to the top of the square tube of the
Handlebar post (26); rotate the cover 45 degrees to align with
the Handlebar (4). Use Phillips screws (27) to fix the Top cover
(25A) to the lower Handlebar cover (25B), so that the Handlebar
(4) and Handlebar post (26) are in between the Handlebar cover
pieces (25A/B). Turn and loosen the Knob (8), pull the pin, and
then insert the Handlebar assembly into the Main frame section
simultaneously. Make sure the pin settles into the desired hole
and then secure the Knob.

5
Step C:
Lock the Saddle (7) on the Seat slider (6) tightly
with wrench.
Adjust the front & back distance of Seat slider (6),
then lock the Seat slider (6) on the Seat post (5)
tightly with Pop-pin knob (8).
Insert the Seat post (5) to the rear upright tube of
Main frame (1), then adjust the height properly and
lock them tightly with Pop-pin knob (8).
Note: You could adjust the front & back distance of
Seat slider (6) by loosing properly the Pop-pin knob
(8) on Seat post (5); you could also adjust the
height of Seat post (5) by loosing properly the
Pop-pin knob (8) on the rear upright tube on Main
frame (1).
Make sure the Saddle (7) is locked tightly on Seat
slider (6) before moving.
Step D:
Attach the Pedals (9L/R) to the Cranks (10L/R)
respectively, viewed from the rider’s seated
position.
Note: Both pedals are labeled, L FOR LEFT
and R FOR RIGHT.
Important:
To tighten，turn the left pedal
COUNTERCLOCKWISE and the right pedal
CLOCKWISE.

6
OPERATION
Leveling the Bike
This bike can be leveled to compensate for uneven surfaces. To
level the bike, please raise or lower four leveler feet located on
the underside of the front and rear stabilizers (Fig.1).
Resistance Adjustment
Pedaling resistance is controlled by the tension control knob (Fig.2).
To increase resistance turn the tension control knob clockwise (+).
To decrease resistance turn the tension control knob
counterclockwise (-). Resistance adjustment can be easily made at
any time. Emergency brake is also equipped in the machine by
simply pushing down the tension knob.
Seat Adjustment
Appropriate seat height helps you exercise efficiently; reduces the
risk of injury and makes you feel more comfortable. Adjusting the
seat forward or backward helps you work on different lower body
muscle groups.
1. Place one pedal in the upward position. Place your foot in the
toe clips, then get in the bike.
2. If your leg is bent too much, you should move the seat up. If
your foot can not touch the pedal or your leg is too straight, you
should move the seat down.
3. Dismount the bike. Loosen and pull the pop pin (Fig.3), then
raise or lower the seat post to the desired position. Make sure
the pop pin settles into the desired hole and then secure it firmly.
4. Loosen and pull the pop pin (Fig.4), then move the seat slider
forward or backward to the desired position. When the seat
slider is in the desired position, secure the pop pin firmly.

7
Handlebar Adjustment
Loosen and pull the pop pin (Fig.5), then raise or lower the handlebar
to the desired position for a more efficient & comfortable ride. Make
sure the pop pin settles into the desired hole and then secure it firmly.
Pedal Strap Adjustment
Place the ball of each foot in the toe clip until the front of the shoe fits
snugly in the toe clip cage. Rotate one foot to within arm’s reach, then
pull up the strap until the toe clip cage fits the shoe snugly and insert
the strap end back into the hoop of the toe clip (Fig.6). Repeat for the
other foot.
Workout
Once you are sitting comfortably, begin pedaling slowly, with your hands resting comfortably on
the handlebar. After you feel secure, you can change seat positions, hand positions and
resistance levels for added enjoyment and variety during your workout.
Dismounting the Bike
Increase the resistance by turning the tension control knob clockwise until the flywheel stops, or
pedal slower until you come to a complete stop.
Warning!
Do not dismount the bike or remove your feet from the pedals until the pedals have completely
stopped.
Moving the Bike
Carefully lift the rear stabilizer to move the bike to another location
(Fig.7). Please gently move the bike as any sudden impact may
affect the operation of the machine.