Sunnydaze Decor LDE-694 User manual

Page 1 / 2
CELEBRATION BEAR
WITH BANNER
LDE-694
Read this manual carefully before use and save it for future reference.
EASY INSTALLATION AND OPERATION INSTRUCTIONS
This item should take approximately 15 minutes to install and inate, when assembled according to this manual.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
2/2021
WARNINGS:

This item contains small parts that can be a choking hazard. Keep all
plastic and wire parts away from children.
Ensure all parts
are accounted for.

Inatable Product Lawn Stakes
Banners Tether Ropes
Blower LED Lights
UL Adapter
Please read and follow all instructions carefully before using the product and retain for future reference.
1. This product is not intended for permanent installation or use.
2. Do not mount or place near gas or electric heaters, replace, candles, or other similar heat sources.
3. Do not secure product wiring with staples or nails or place on sharp hooks or nails.
4. Unplug the product when leaving the house, when retiring for the night, or if left unattended.
5. This is an electrical product and not a toy! To avoid risk of re, burns, personal injury or electric shock, this product
should not be played with or placed where children can reach it.
6. Do not hang ornaments or other objects from the cord.
7. Before using or reusing, inspect the product carefully. Discard and DO NOT operate the product if cuts, cracks,
damages or frayed wire insulation cord, loose connections, or exposed copper wire are visible.
8. Do not remove or change the bulb(s) inside while the power is on.
9. Replace failed bulb(s) immediately. Purchase bulb(s) of the same rated voltage and wattage to prevent overheating.
IMPORTANT SAFETY INFORMATION

WARNING:



Page 2 / 2
STEP 1: Remove all contents from packaging and lay out the deated inatable on a clean, clear area that is away from
sharp objects.
STEP 2: Ensure the zipper at the base of the inatable is zipped shut.
STEP 3: Locate the air intake on the blower and make sure it is clear of fabric or other obstructions, and that it is facing
upright.
STEP 4: Plug the adapter plug into a properly grounded GFCI wall outlet. The blower/fan will immediately begin to ll
the inatable product with air. NOTE: It is helpful to lift up on the fabric as the blower inates the unit to avoid clogging
the blower air intake.
STEP 5: Once fully inated, tie the included tether ropes to the sewn-in loops on the sides of the inatable. Gently pull
on the tether ropes to extend and straighten them out. Position the extended tether ropes with equal spacing distance.
STEP 6: To secure the inatable into the ground, push lawn stakes through the loops that are sewn to the bottom of the
inatable. Push the additional lawn stakes into the ground a few inches out from where the loose ends of the tether ropes
are lying on the ground. Tie the loose ends of the tether ropes to the tops of the lawn stakes. Gently pull and tighten each
tether rope to adjust the inatable to an upright and fully secure position.
STEP 7: To hang the banner, open the clips that are located on the hands of the unit by
pulling the lever upward. Place the banner between the teeth of the clip and carefully
press the clip lever closed.
2/2021
CARE AND STORAGE

For best performance, operate this item indoors or in a sheltered outdoor area. It is also recommend that you bring this
item indoors during adverse weather (extreme cold, strong winds and/or rain). When not in use, store this product in its
original packaging. Keep away from heat and moisture.
1. Only use the transformer supplied by the manufacturer.
2. Adults should supervise children while this product is in use. Keep children away from the transformer, as it heats up
during operation.
3. Assemble the product according to the instructions and read all instructions carefully before assembly.
4. Spot clean fabric with a damp cloth. Never use harsh chemicals or abrasive materials.
ASSEMBLY

TROUBLESHOOTING
Carefully read and follow all Care and Storage, Safety, and Assembly Instructions; the most common
troubleshooting tips are referenced under each set of instructions.

1. The power source may have been interrupted, or the cord may be unplugged.
2. Blower airow may be obstructed. Unplug the blower and check that the intake vent is free from debris. Also
ensure the inatable product is not blocking the intake vent.
3. Check that the zipper near the blower is closed.
4. Inspect fabric for holes and tears. Do not use if product if fabric is damaged.