Sunrise Medical Quickie 7R User manual

O w n e r ’ s M a n u a l
Quickie®7R Adjustable
Quickie®7RS (welded)
Supplier: This manual must be given to the rider of this wheelchair.
Rider: Before using this wheelchair read this entire manual and save it
for future reference.
S E C T I O N E N G L I S H
QUICKIE 7R
Mode d’emploi
Quickie®7R réglable
Quickie®7RS (soudé)
Fournisseur : Ce manuel doit être remis à l’utilisateur / utilisatrice
de ce fauteuil roulant.
Utilisateur / Utilisatrice : Avant d’utiliser ce fauteuil roulant, lisez entière-
ment ce manuel et conservez le pour le consulter ultérieure-
ment.
Chaque fauteuil est livré avec un manuel d’instructions en anglais. Les versions en espagnol
et en français sont à votre disposition en format PDF sur le site : www.SunriseMedical.com.
Veuillez vous rendre à la page de votre produit pour télécharger le manuel dans la langue
souhaitée, ou contactez un fournisseur agréé Sunrise Medical.
M a n u a l d e I n s t r u c c i o n e s
Quickie®7R Ajustable
Quickie®7RS (soldada)
Distribuidor: Este manual debe ser entregado al pasajero de esta
silla de ruedas.
Pasalero: Antes de usar esta silla de ruedas, lea este manual en
su totalidad y guárdelo para futura referencia.
Cada una de las sillas se envía con un manual de instrucciones en inglés. El manual en español
o francés está disponible en formato PDF en nuestra página en Internet:
www.SunriseMedical.com. Ingrese a la página del producto específico para descargar el manual,
o comuníquese con el proveedor autorizado de Sunrise Medical.

MK-100084 Rev. A 2
QUICKIE 7R
I. INTRODUCTION
SUNRISE MEDICAL LISTENS
Thank you for choosing a Quickie wheelchair. We want to hear your questions or comments about this manual, the
safety and reliability of your chair, and the service you receive from your Sunrise supplier. Please feel free to write
or call us at the address and telephone number below:
Sunrise Medical
Customer Service Department
2842 Business Park Ave
Fresno, CA 93727
[phone]
Be sure to return your warranty card, and let us know if you change your address. This will allow us to keep you up
to date with information about safety, new products and options to increase your use and enjoyment of this wheel-
chair. If you lose your warranty card, call or write and we will gladly send you a new one.
FOR ANSWERS TO YOUR QUESTIONS
Your authorized supplier knows your wheelchair best, and can answer most of your questions about chair safety,
use and maintenance. For future reference, fill in the following:
Supplier:________________________________________________
Address:________________________________________________
_______________________________________________________
Telephone: ______________________________________________
Serial #: __________________ Date/Purchased: _______________
INFORMATION YOU S OULD KNOW
No component of this chair was made with Natural Rubber Latex.
DISPOSAL AND RECYCLING INFORMATION
When this product reaches the end of its life, please take it to an approved collection or recycling point designated
by your local or state government. This wheelchair is manufactured using a variety of materials, Your product
should not be disposed of as ordinary household waste. You should dispose of your wheelchair properly, according
to local laws and regulations. Most materials that are used in the construction of this product are fully recyclable.
The seperate collection and recycling of your product at the time of disposal will help conserve natural resources
and ensure that it is dosposed in a manner that protects the environment.
Ensure you are the legal owner of the product prior to arranging for the product disposal in accordance with the
above recommendations.

MK-00084 Rev. A
3
QUICKIE 7R
I. INTRODUCTION ............................................................... 2
II. TABLE OF CONTENTS ...................................................... 3
III. YOUR C AIR AND ITS PARTS ....................................... 4
IV. NOTICE - READ BEFORE USE ......................................... 5
A.Choose the Right Chair & Safety Options ................. 5
B. Review This Manual Often ............................................. 5
C.Warnings.............................................................................. 5
V. GENERAL WARNINGS....................................................... 5
A.Weight Limit ...................................................................... 5
B. Intended Use ..................................................................... 5
C.Attendants and Caregivers.............................................. 5
D. Accessories ......................................................................... 5
E. Know Your Chair .............................................................. 5
F. Reduce The Risk of an Accident ................................... 6
G.Safety Checklist ................................................................. 6
.Changes & Adjustments .................................................. 6
I. Environmental Conditions .............................................. 6
J. Terrain ................................................................................. 6
K. Street Use .......................................................................... 6
L. Motor Vehicle Safety ........................................................ 6
M.When You Need elp ..................................................... 7
VI. SAFETY WARNINGS: FALLS & TIP-OVERS.................. 8
A.Center of Balance ............................................................ 8
B. Dressing or Changing Clothes ...................................... 8
C.Obstacles ............................................................................ 8
D. Front Caster Lift ................................................................ 8
E. Reaching or Leaning.......................................................... 8
F. Moving Backward............................................................... 8
G.Escalators............................................................................. 9
.Ramps, Slopes & Sidehills ................................................ 9
I. Transfer ................................................................................ 10
J. Curbs & Single Steps......................................................... 10
K. Climbing a Curb or Single Step...................................... 11
L. Descending a Curb or Single Step................................. 11
M.Stairs ..................................................................................... 11
N.Climbing Stairs .................................................................. 11
O.Descending Stairs ............................................................. 11
VII. WARNINGS: COMPONENTS & OPTIONS ................. 12
A.Anti-Tip Tubes ................................................................... 12
B. Armrests ............................................................................. 12
C.Cushion & Sling Seats ...................................................... 12
D. Fasteners ............................................................................ 12
E. Footrests.............................................................................. 12
F. Pneumatic Tires ................................................................. 12
G.Offset Seating Option....................................................... 13
.Positioning Belts Option .................................................. 13
I. Push andles Option........................................................ 13
J. Quick-Release Axles ........................................................ 13
K. Rear Wheels ...................................................................... 13
L. Rear Wheel Locks ............................................................ 13
M.Modified Seat Systems ..................................................... 13
N.Seat and Back Upholstery .............................................. 14
O.Backrest Tension Adjustable ............................................ 14
P. Freestyle Back (Option)................................................... 14
Q.Folding Lock Down Adjustable Backrest ..................... 14
R. Seat Back.............................................................................. 14
VIII. USE AND MAINTENANCE ............................................... 15
A.Introduction ........................................................................ 15
B. Critical Safety Checks....................................................... 15
C.Cleaning................................................................................ 15
D. Safety Checklist.................................................................. 15
E. Troubleshooting Chart ..................................................... 15
F. To Mount and Remove Rear Wheels............................ 16
G.Wheel Locks....................................................................... 16
.Single Post eight Adjustable Armrests ....................... 17
I. Padded Swing-away Armrests ......................................... 17
J.Flip-up Footplate .................................................................. 17
K. Freestyle Back..................................................................... 17
L. Back Angle Performance .................................................. 18
M.Tension Adjustable Upholstery....................................... 18
N.Seat Sling Adjustment........................................................ 19
O.Ultra Light Seat Sling......................................................... 19
P. Cushion Installation........................................................... 19
Q.Storage Tips......................................................................... 19
R. Check Out........................................................................... 19
IX DEALER SERVICE AND ADJUSTMENT ......................... 20
A.Dealer Service Introduction............................................ 20
B. Critical Maintenance Tips................................................. 20
C.Cleaning................................................................................ 20
D. Rear Wheel Axle Nut Adjustment................................. 20
E. Anti-tip Receiver................................................................ 20
F. Wheel Locks....................................................................... 21
G.Armrest Receiver Attachment........................................ 21
.Padded Swing Away Armrest Option............................ 22
I. Casters ................................................................................. 22
J. Anti-Flutter Kit Installation ............................................. 23
K. Footrest eight Adjustment............................................ 23
L. Adjusting Rear Seat eight ............................................. 24
M.Depth Adjustable Backrest.............................................. 24
N.Back Angle Adjustment .................................................... 25
O.Freestyle Back Maintenance and Adjustment.............. 25
P. 4-LINK Rear Suspension.................................................. 26
Q.Rear Axle ............................................................................. 27
R. Rear Wheel Spacing ......................................................... 29
S. Back Angle Adjustment..................................................... 29
T. Check Out........................................................................... 30
X. SUNRISE LIMITED WARRANTY ..................................... 31
II. TABLE OF CONTENTS

QUICKIE 7R ADJUSTABLE AND 7RS
MK-100084 Rev. A 4
QUI C KI E 7R
III. OUR CHAIR AND ITS PARTS
1. Freestyle Backrest (Optional)
2. Tire
3. andrim
4. Quick Release Axle
5. Spokes
6. Caster wheel
7. Caster housing
8. Camber tube
9. Caster fork
10. Footrest
11. Wheel Lock
12. Seat Sling
All features may not be available with some chair setups or in conjunction with another chair feature.
Please consult your authorized supplier for more information.
Adjustments
Caster angle, Center of Gravity, rear seat
height, back angle, footrest length, rear wheel
spacing, wheel locks, back height
Color
Quickie colors
Frame Dimensions
Frame width: Std 12" - 20"
Seat depth: 12" - 20"
Backrest
Non-folding
Folding Lock Down Angle Adjustable
eight-adjustable & angle: 11"-14", 12"-16",
14"-18", 16"-20" Fixed eight: 8"-20"
Opt– adjustable upholstery, vented adjustable
upholstery, folding push handles, tele-
scoping push handles
Opt– Freestyle Back
Footrest
Std– Tubular
Opt– Tubular w/Cover,
Angle Adjustable Platform,
Ultra lite platform footrest
Carbon Fiber Platform
Casters
Std - 5" Low-profile Polyurethane
Opt- 4" Low-profile Poly, 4" Micro Light Up
4"x1" Aluminum Poly
4"x1.5" Aluminum soft Roll, 3" Micro,
3" Micro Light Up
4", 5" & 6" x 1-1/2" wide poly, 6" Poly
Frog Legs
Armrests
Opt– Padded Swing-Away
Opt– Single-Post eight-Adjustable
Axle Bracket
Std– Fore/Aft CG Adjustable Bracket
Opt Camber– 0°, 3°, 6°
Axles
Std– stainless steel
Opt– quad-release axle nuts
Anti-tip tubes
Opt– Rear anti-tip tubes
Standard rear wheels
Std– Lite spoke, 5 spoke Mag
Quickie Performance wheels
Opt– Spinergy, LX & Spox, Ultra lightweight
Opt– Mountain, Topolino carton w/Red or
yellow accents.
Tire size
Std– 20”,22”,24",25", 26”
Tire types
Std - Pneumatic, Full Poly
Opt - Airless insert,
igh-pressure clincher
Black, (22”,24",26"),
Mountain bike Knobby V-TRAK
(24" only),
Shox, Schwalbe Marathon, Speed Run
(20”,22”,24”, 25”, 26”)
and rims
Std– aluminum
Opt– plastic-coated,
Natural Fit, Natural Fit LT, Natural Fit
(No Thumb Grip)
Spinergy Flex Rim, Surge, QGrip
Wheel locks
igh-push, high-pull, ergo scissor
Opt- compact
A
B
7RS (Welded)(Adjustable)
12
12
3
4
5
96
7
10
11
8
QUICKIE 7R

V. GENERAL WARNINGS
A. WEIG T LIMIT
WARNING
NEVER exceed the weight limit specified by Sunrise Medical. The weight
capacity provided by your manufacturer is for the combined weight of a rider
and items carried using on-board storage. If you do exceed the weight limit,
damage to your chair, a fall, tip-over or loss of control may occur and cause
severe injury to the rider or others.
Weight Capacity
Quickie 7R - 265lbs/(120kg).
B. INTENDED USE
The 7R wheelchair's intended use is to provide mobility to persons limited
to a sitting position.
WARNING
DO NOT use this device for purposes other than what is intended by the
manufacturer
1. The wheelchiar is not designed for weight training and is unsafe for
use as a seat while weight training. Weight training from the wheel-
chair substantially changes the stability of the chair and may cause
tipping.
2. DO NOT stand on the frame of the wheelchair.
3. NEVER allow someone to stand on your chair or use it as a step
ladder.
4. This chair is designed for a single rider only.
5. Unauthorized modifications and use of parts or accessories not sup-
plied or approved by Sunrise Medical may change the chair struc-
ture. This will void the warranty and may cause a safety hazard. If
the warning is ignored, damage to your chair, and the potential
severe injury of the person using the chair for unintended purposes
can occur.
C. ATTENDANTS AND CAREGIVERS
WARNING
Before you assist a rider, be sure to read all warnings contained in this
manual, and follow all instructions that apply. Be aware that after consulting
a healthcare advisor, you will need to learn safe and proven body mechanics
to use and create assistive methods best suited to your abilities.
D. ACCESSORIES
WARNING
Unauthorized modifications or use of parts, or accessories not supplied or
approved by Sunrise Medical may change the chair structure. This will void
the warranty and may cause a safety hazard.
Some problems that may occur, but are not limited to:
1. Incorrect Wheels and/or tires that put the rider at risk of a fall or tip-
over.
2. Adding a component to the frame, changing the structural integrity of
the chair.
3. Any modification or disassembly can potentially create an unsafe situa-
tion where rider and/or attendant are put at risk.
E. KNOW YOUR C AIR
WARNING
Every wheelchair is different. Take the time to learn the feel of this chair
before you begin riding. Start slowly, with easy, smooth strokes. If you are
used to a different chair, you may use too much force and tip over. If you
use too much force, damage to your chair, a fall, tip-over or loss of control
may occur and cause severe injury to the rider or others.
MK-00084 Rev. A
5
QUI C KI E 7R
IV. NOTICE– READ BEFORE USE
A. C OOSE T E RIG T C AIR & SAFETY OPTIONS
Sunrise provides a choice of many wheelchair styles to meet your needs.
This product is intended for single person use only. Final selection of the
type of wheelchair, options and adjustments rests solely with you and your
health care professional. Choosing the best chair for your unique mobility
needs, will depend on such things as:
1. Your disability, strength, balance and coordination.
2. The types of hazards you must overcome in daily use (where you
live and work, and other places you are likely to use your chair).
3. The need for options that will improve your positioning, safety and
comfort (such as anti-tip tubes, positioning belts, or special seating
systems).
B. REVIEW T IS MANUAL OFTEN
Before using this chair you, and each person who may assist you, should
read this entire manual and make sure to follow all instructions. Review the
warnings often, until they are second nature to you.
C. WARNINGS
The word “WARNING” refers to a hazard or unsafe practice that may cause
severe injury or death to you or to other persons. The “Warnings” are in
three main sections, as follows:
1. V — GENERAL WARNINGS
ere you will find a safety checklist and a summary of risks you
need to be aware of before you ride this chair.
2. VI– SAFETY WARNINGS: FALLS & TIP-OVERS
ere you will learn about practices for the safe use of your chair,
and how to avoid a fall or tip-over while you perform daily activities
in your chair.
3. VII — WARNINGS — COMPONENTS & OPTIONS
ere you will learn about the components of your chair and options
you can select for safety. Consult your authorized supplier and your
health care advisor to help you choose the best set-up and options
for safe use.
NOTE– Where they apply, you will also find “Warnings” in other sec-
tions of this manual. eed all warnings in these sections. If you
fail to do so a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.

MK-100084 Rev. A 6
QUI C KI E 7R V. G E N ERAL WA R NINGS
J. TERRAIN
WARNING
1. Based on ANSI/RESNA testing, Sunrise Medical recommends the use
of a caster wheel with a minimum diameter of 5”, if the wheelchair
will be overcoming obstacles up to 1/2” on a regular basis.
2. Your chair is designed for use on firm, even surfaces such as con-
crete, asphalt, indoor flooring, and carpets.
3. Do not operate your chair in sand, loose soil, or over rocky terrain.
4. If you use your chair on terrain that is rougher than described above
there is a danger that screws and bolts will loosen prematurely, and
that damage to wheels or axles could put the rider at risk of a fall,
tip-over, or loss of control.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
K. STREET USE
WARNING
1. This product is not intended for street use.
2. Avoid streets whenever possible.
3. Obey and follow all legal pedestrian pathways, and laws that apply to
pedestrians.
4. Be alert to the danger of motor vehicles in parking lots, or if you
must cross a road.
If you fail to heed this warning, damage to your chair, and a possible colli-
sion may occur and cause severe injury to the rider or others.
L. MOTOR VE ICLE SAFETY
If possible and feasible, the rider should transfer to the Original Equipment
Manufacturer vehicle seat and use the OEM vehicle restraint.
Sunrise Medical does provide a WC-19 Wheelchair Tie-Down and
Occupant Restraint System, otherwise called a Transit Option. To Identify
whether your wheelchair has been manufactured with the Transit Option
installed, look for four points of securement. Two Front points, (A) and
two rear points (B). These points are recognized by the securement point
decal which can be found on or near the securement points. If you wheel-
chair is equipped with the Transit Option please review the Transit
Securement supplement that was provided with the wheelchair for addi-
tional information and instructions. You can request a copy from your
authorized supplier, or Sunrise medical if you don’t have it.
21
F. REDUCE T E RISK OF AN ACCIDENT
WARNING
1. BEFORE you begin riding, you should be trained in the safe use of
this chair by your health care advisor.
2. Practice bending, reaching and transfers until you know the limit of
your ability. ave someone help you until you know what can cause
a fall or tip-over and how to avoid doing so.
3. Be aware that you must develop your own methods for safe use
best suited to your level of function and ability.
4. NEVER try a new maneuver on your own. Ask the advice of your
health care provider to lower the risk of a fall or tip over.
5. Get to know the areas where you plan to use your chair. Look for
hazards and learn how to avoid them.
G. SAFETY C ECKLIST
WARNING
Before Each Use Of Your Chair:
1. Make sure the chair rolls easily and that all parts work smoothly.
Check for noise, vibration, or a change in ease of use. (This may indi-
cate low tire pressure, loose fasteners, or damage to your chair).
2. Immediately repair any problem. Your authorized supplier can help
you find and correct the problem.
3. Check to see that both quick-release rear axles are locked. When
locked, the axle button will “pop out” fully. If not locked, the wheel
may come off and cause you to fall.
4. If your chair has anti-tip tubes, lock them in place.
. C ANGES & ADJUSTMENTS
WARNING
1. See your healthcare advisor and have them adjust seating compo-
nents any time a change or adjustment needs to be made.
2. Unauthorized modifications or use of parts not supplied or
approved by Sunrise may change the chair structure. This will void
the warranty and may cause a safety hazard.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
I. ENVIRONMENTAL CONDITIONS
WARNING
1. Use extra care if you must ride your chair on a wet or slick surface.
If you are in doubt, ask for help.
2. Contact with water or excess moisture may cause your chair to
rust or corrode. Avoid all extreme weather situations if possible.
a. Do not use your chair in a shower, pool or other body of water.
The chair tubing and parts are not water-tight and may rust or
corrode from the inside.
b. Avoid excess moisture (for example, do not leave your chair in a
damp bathroom while taking a shower).
c. Dry your chair as soon as you can if it gets wet, or if you use
water to clean it.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
Loo for this symbol on your wheelchair. It indicates wheelchair
securement points which conform to ANSI/RESNA (1998) V.1 –
Section 19 & ANSI/RESNA (2012) V.4 WC-19.
12
A
B

MK-00084 Rev. A
7
QUI C KI E 7R
WARNING
If your chair is NOT equipped with the Transit Option:
1. NEVER let anyone sit in this chair while in a moving vehicle.
a. ALWAYS move the rider to an approved vehicle seat.
b. ALWAYS secure the rider with proper motor vehicle restraints.
2. In an accident or sudden stop the rider may be thrown from the
chair. Wheelchair seat belts will not prevent this, and further injury
may result from the belts or straps.
3. NEVER transport this chair in the front seat of a vehicle. It may shift
and interfere with the driver.
4. ALWAYS secure this chair so that it cannot roll or shift.
5. Do not use any chair that has been involved in a motor vehicle acci-
dent. The frame and/or components may have been changed due to
the accident. Such items could be, but are not limited to: bent, loos-
ened, and/or broken components that were subjected to an impact.
Failure to heed these warnings puts you and others that may assist you at a
high risk of injury.
M. W EN YOU NEED ELP
WARNING
For The Rider: Make sure that each person who helps you reads and fol-
lows all warnings and instructions that apply.
For Attendants:
1. Work with the rider’s doctor, nurse or therapist to learn safe meth-
ods best suited to your abilities and those of the rider.
2. Tell the rider what you plan to do, and explain what you expect the
rider to do. This will put the rider at ease and reduce the risk of an
accident.
3. Make sure the chair has push handles. They provide secure points for
you to hold the rear of the chair to prevent a fall or tip-over. Check
to make sure push handle grips will not rotate or slip off.
4. To prevent injury to your back, use good posture and proper body
mechanics. When you lift or support the rider or tilt the chair, bend
your knees slightly and keep your back as upright and straight as you
can.
5. Remind the rider to lean back when you tilt the chair backward.
6. When you descend a curb or single step, slowly lower the chair in
one easy movement. Do not let the chair drop the last few inches to
the ground. This may damage the chair or injure the rider.
7. To avoid tripping, unlock and rotate anti-tip tubes up, out of the way.
8. Whenever you aren’t attending the wheelchair, ALWAYS use the
wheel-lock to secure the rear wheels, and lock the anti-tip tubes in
place.
If you fail to ask for help when in doubt, you run a high risk of a fall, tip-
over or loss of control that may occur and cause severe injury to the rider
or others.
V. G E N ERAL WA R NINGS

VI. WARNINGS: FALLS & TIP-OVERS
MK-100084 Rev. A 8
QUI C KI E 7R
7. Keep both of your hands on the handrims as you go over an obsta-
cle.
8. Never push or pull on an object (such as furniture or a doorjamb)
to propel your chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
D. FRONT CASTER LIFT
WARNING
Front caster lift can occur when the front wheels, ordinarily in contact with
the ground, are either intentionally, or unintentionally caused to lift from
the ground while the rear wheels remain in contact. Pitch control (partial
or full) should NEVER be attempted without consulting your healthcare
advisor and making sure that anti-tips are installed.
If you fail to heed this warning, you are at a high risk of damage to your
chair, a fall, tip-over or loss of control that may occur and cause severe
injury to the rider or others.
E. REAC ING OR LEANING
WARNING
If you reach or lean it will affect the center of balance of your chair. This
may cause you to fall or tip over. When in doubt, ask for help or use a
device to extend your reach.
1. NEVER reach or lean if you must shift your weight sideways or rise up
off the seat.
2. NEVER reach or lean if you must move forward in your seat to do
so. Always keep your buttocks in contact with the backrest.
3. NEVER reach with both hands (you may not be able to catch your-
self to prevent a fall if the chair tips).
4. NEVER reach or lean to the rear unless your chair has anti-tip tubes
locked in place.
5. DO NOT reach or lean over the top of the seat back. This may
damage one or both backrest tubes and cause you to fall.
6. If You Must Reach Or Lean:
a. Do not lock the rear wheels. This creates a tip point and makes
a fall or tip-over more likely.
b. Do not put pressure on the footrests.
c. Move your chair as close as you can to the object you wish to
reach.
d. Do not try to pick up an object from the floor by reaching
down between your knees. You are less likely to tip if you reach
to the side of your chair.
e. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
f. Firmly grasp a rear wheel or an armrest with one hand. This will
help to prevent a fall if the chair tips.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
F. MOVING BACKWARD
WARNING
Use extra care when you move your chair backward. Your chair is most
stable when you propel yourself forward. You may lose control or tip over
if one of the rear wheels hits an object and stops rolling.
1. Propel your chair slowly and smoothly.
2. If your chair has anti-tip tubes, make sure to lock them in place.
3. Stop often and check to be sure your path is clear.
If you fail to heed this warning, you are at a high risk of damage to your
chair, a fall, tip-over or loss of control that may occur and cause severe
injury to the rider or others.
A. CENTER OF BALANCE
WARNING
The point where this chair will tip forward, back or to the side depends on
its center of balance and stability. ow your chair is set up, the options you
select and the changes you make may affect the risk of a fall or tip-over.
1. The Most Important Adjustment Is:
The position of the rear wheels. The more you move the rear
wheels forward, the more likely your chair will tip over backward.
2. The Center Of Balance Is Also Affected By:
a. A change in the set-up of your chair, including:
• The distance between the rear wheels.
• The amount of rear wheel camber.
• The seat height and seat angle.
• Backrest angle.
b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
d. A back pack or other options and the amount of added weight.
3. To Reduce The Risk Of An Accident:
a. Consult your doctor, nurse or therapist to find out what axle
and caster position is best for you.
b. Consult your authorized supplier BEFORE you modify or adjust
this chair. Be aware that you may need to make other changes
to correct the center of balance.
c. ave someone help you until you know the balance points of
your chair and how to avoid a tip-over.
d. Use anti-tip tubes.
If you fail to heed these warnings, you are at a high risk of a fall, tip-over or
loss of control that could cause severe injury to the rider or others.
B. DRESSING OR C ANGING CLOT ES
WARNING
Your weight may shift if you dress or change clothes while seated in this
chair.
To reduce the risk of a fall or tip-over:
1. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
2. Lock anti-tip tubes in place. (If your chair does not have anti-tip
tubes, back it up against a wall and lock both rear wheels).
If you fail to heed this warning, damage to your chair, a fall, tip-over or loss
of control may occur and cause severe injury to the rider or others.
C. OBSTACLES
WARNING
Riding over curbs or obstacles can cause tipping and serious bodily harm. If
you have any doubt that you can safely cross any curb or obstacle, ALWAYS
ASK FOR ELP. Be aware of your riding skills and personal limitations.
Develop new skills only with the help of a companion.
To avoid the risk of traversing obstacles:
1. Keep a lookout for danger – scan the area well ahead of your chair
as you ride.
2. Make sure the floor areas where you live and work are level and free
of obstructions.
3. Remove or cover threshold strips between rooms.
4. Install a ramp at entry or exit doors. Make sure there is not a drop
off at the bottom of the ramp.
5. To elp Correct Your Center Of Balance:
a. Lean your upper body FORWARD slightly as you go UP over an
obstacle.
b. Press your upper body BACKWARD as you go DOWN from a
higher to a lower level.
6. If your chair has anti-tip tubes, do not go over an obstacle without
help.

G. ESCALATORS
WARNING
NEVER use this chair on an escalator, even with an attendant. If you do, a fall
or tip-over is likely.
If you fail to heed this warning you and others that may be assisting you, are
at a high risk of severe injury.
. RAMPS, SLOPES & SIDE ILLS
WARNING
Whenever possible, avoid riding on a slope, which includes a ramp or sidehill.
This will change the center of balance of your chair. Your chair is less stable
and more difficult to manuever. when it is at an angle. When moving up a
hill, anti-tip tubes may not prevent a fall or tip-over.
1. DO NOT use your chair on a slope steeper than 6%. (A 6% slope
means: one foot in elevation for every ten feet of slope length.)
2. ALWAYS go as straight up and as straight down as you can. (Do not
“cut the corner” on a slope or ramp.)
3. DO NOT turn or change direction on a slope.
4. When you have to use a ramp, always stay in the CENTER of the
ramp. Make sure ramp is wide enough that you have no risk of going
off the edge.
5. DO NOT stop on a steep slope. If you stop, you may lose control of
your chair.
6. NEVER use rear wheel locks to try to slow or stop your chair. This is
likely to cause your chair to veer out of control.
7. ALWAYS be aware of:
a. Wet or slippery surfaces.
b. A change in grade on a slope (or a lip, bump or depression).
These may cause a fall or tip-over.
c. A drop-off at the bottom of a slope or ramp. A drop-off as small
as 3/4 inch can stop a front caster and cause the chair to tip for-
ward.
8. To Reduce The Risk Of A Fall Or Tip-Over:
a. Lean or press your body UP ILL. This will help adjust for the
change in the center of balance caused by the slope or sidehill.
b. Keep pressure on the handrims to control your speed on a down
slope. If you go too fast you may lose control.
c. ASK FOR ELP any time you are in doubt.
9. Ramps At ome & Work– For your safety, ramps at home and work
must meet all legal requirements for your area:
a. AVOID A DROP-OFF
Make sure there is a section at the top or bottom to smooth out
the transition.
b. ALWAYS stay in the center of the ramp and control your speed.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss
of control may occur and can possibly cause severe injury to the rider or
others.
6543
MK-00084 Rev. A
9
QUI C KI E 7R VI. WA RNING S : FALL S & T I P - OVERS
IFyou need to go down a hill:
a. The Downslope should be
less than 6°
b. GO SLOW
c. ALWAYSGo Straight down
d. ALWAYSControl your speed.
e. NEVERturn on a hill.
IFyou need to go up a hill:
a. The Upslope should be less
than 6°
b. ALWAYSGo Straight up
c. NEVERStop on the upslope.
d. NEVERturn on a hill.
e. ALWAYSlean forward
IF you need to traverse a
Sidehill:
a. sidehill must be Less than 6°
or you are ris ing a tip over
b. DON’T STOP.
c. DO NOT ma e any Turns on
the sidehill.
If you need to traverse a
Ramp:
a. Go S ow y.
b. Watch out for Drop-offs.
c. ALWAYS go straight down.
d. Stay centered on the Ramp.
6
5
4
3

MK-100084 Rev. A 10
QUI C KI E 7R VI. WA RNING S : FALL S & T I P - OVERS
I. TRANSFERS
WARNING
It is dangerous to transfer on your own. It requires good balance and agility. Be aware that there is a point during
every transfer when the wheelchair seat is not below you.
To avoid a fall:
1. Work with your health care advisor to learn safe methods for transfers.
a. Learn how to position your body and how to support yourself during a transfer.
b. ave someone help you until you learn safe transfer methods.
2. Lock the rear wheels before you transfer.
3. Be aware that the chair can still slide and/or tip. The wheel lock keeps the rear wheels from rolling while
you are perforrming the transfer.
4. Make sure that the pneumatic tires are properly inflated. Low tire pressure may allow the rear wheel
locks to slip. (see table in Section G “Pneumatic Tires”
5. Move your chair as close as you can to the seat you are transferring to.
If possible, use a transfer board.
6. Rotate the front casters until they are as far forward as possible.
7. If you can, remove the footrests, or swing them out of the way.
a. Make sure your feet do not catch in the space between the footrests.
b. Avoid putting weight on the footrests as this may cause the chair to tip.
8. Make sure armrests are removed, or out of the way and do not interfere with the transfer.
9. Transfer as far back onto the seat surface as you can. This will reduce the risk that the chair will tip or
move away from you.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and can pos-
sibly cause severe injury to the rider or others.
87
9
7
Before transferring:
Flip-bac , or Remove the arm-
rests out of the way.
Swing, or remove the footrests
out of the way.
Ma e sure the wheel loc is set.
Optimum Transfer position
GET READY TRANSFER ADJUST
8
1. 2. 3.
ADJUST
GET READY TRANSFER
J. CURBS & SINGLE STEPS
WARNING
Before riding over curbs, and negotiating even a single step, ALWAYS ask for assistance first. Curbs and steps
can cause tipping and serious bodily harm. When in doubt as to your ability to avoid, or traverse any obstacle,
always ask for help. Be aware of your riding skills and personal limitations. Develop new skills only with the help
of a companion.
For Attendant: Each person who assists the rider with curbs and steps should read and follow all instructions
and warnings pertaining to attendants, and caregivers.
1. Do not try to climb a high curb or step (more than 4 inches high) UNLESS you have help. Doing so may
cause your chair to exceed its balance point and tip over.
2. Go straight up and straight down a curb or step. If you climb or descend at an angle, a fall or tip-over is
likely.
3. Be aware that the impact of dropping down from a curb or step can damage your chair or loosen fasten-
ers.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and can pos-
sibly cause severe injury to the rider or others.
9

MK-00084 Rev. A
11
QUI C KI E 7R VI. WA RNING S : FALL S & T I P - OVERS
K. CLIMBING A CURB OR SINGLE STEP
WARNING
For Attendant: follow these steps to help the rider climb a curb or single step going BACKWARD:
1. Stay behind the chair.
2. Continue backward until the rear wheels contact the face of the curb or step. Lift and roll the rear
wheels to the top of the curb.
3. Pull the chair backwards until the caster wheels have cleared the edge of the curb and return the chair to
it’s rolling position.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and cause
severe injury to the rider or others.
L. DESCENDING A CURB OR SINGLE STEP
WARNING
For Attendant:: Follow these steps to help a rider descend a curb or single step going FORWARD:
1. Stay at the rear of the chair.
2. Several feet before your reach the edge of the curb or step, tip the chair slightly and pull it backward.
3. When the chair is at it’s balance point, carefully step forwards until the rear wheels reach the edge of the
curb or step. Then allow the rear wheels to slowly roll down onto the lower level.
4. Push the chair forward until you are standing on the lower level.
5. When the rear wheels are safely on the lower level, tilt the chair back to its balance point.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and cause
severe injury to the rider or others.
M. STAIRS
WARNING
1. NEVER use this chair on stairs UNLESS you have someone to help you. Doing so is likely to cause a fall
or tip-over.
2. Negotiating stairs with a wheelchair always requires at least 2 attendants for safety.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and cause
severe injury to the rider or others.
N. CLIMBING STAIRS
WARNING
1. Use at least two attendants to move a chair and rider up stairs.
2. Move the chair and rider BACKWARD up the stairs.
3. The person at the rear is in control. e or she tilts the chair back to its balance point.
4. A second attendant at the front firmly grasps a non-detachable part of the front frame and lifts the chair
up and over one stair at a time.
5. The attendants move to the next stair up. Repeat for each stair, until you reach the landing.
O. DESCENDING STAIRS
WARNING
1. Use at least two attendants to move a chair and rider down stairs.
2. Move the chair and rider FORWARD down the stairs.
3. The person at the rear is in control. e or she tilts the chair to the balance point of the rear wheels and
rolls it to the edge of the top step.
4. A second attendant stands on the third step from the top and grasps the chair frame. e or she lowers
the chair one step at a time by letting the rear wheels roll over the stair edge.
5. The attendants move to the next stair down. Repeat for each stair, until you reach the landing.
9
9
10
10
10
10

VII. WARNINGS: COMPONENTS & OPTIONS
MK-100084 Rev. A 12
QUI C KI E 7R
E. FOOTRESTS
WARNING
1. At the lowest point, footrests should be AT LEAST 2 inches off the
ground. If set too LOW, they may “hang up” on obstacles you can
expect to find in normal use. This may cause the chair to stop sud-
denly and tip forward.
2. To Avoid A Trip Or Fall When You Transfer:
a. Make sure your feet do not “hang up” or get caught in the space
between the footrests.
b. Avoid putting weight on the footrests, as the chair may tip for-
ward.
c. Footrests should be swung out of the way or removed whenever
entering or exiting the wheelchair.
3. NEVER lift this chair by the footrests. Footrests detach and will not
bear the weight of this chair. Lift this chair only by non-detachable
parts of the main frame.
4. Never use the footrests of your chair to open doors, this may cause
them to fail prematurely and create an unsafe situation.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
F. PNEUMATIC TIRES
WARNING
Proper inflation extends the life of your tires and makes your chair easier
to use.
1. Do not use this chair if any of the tires are under- or over-inflated.
Check weekly for proper inflation level, as listed on the tire sidewall.
2. Low pressure in a rear tire may cause the wheel lock on that side to
slip and allow the wheel to turn when you do not expect it.
3. Low pressure in any of the tires may cause the chair to veer to one
side and result in a loss of control.
4. Over-inflated tires may burst.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
A. ANTI-TIP TUBES
WARNING
Anti-tip tubes can help keep your chair from tipping over backward in
normal conditions.
1. Sunrise recommends the use of anti-tip tubes:
2. When locked in place (in the “down” position) anti-tip tubes should
be BETWEEN 1 1/2 to 2 inches off the ground.
a. If set higher than 2 inches, they may not prevent a tip-over.
b. If set lower than 1 1/2 inches, they may “hang up” on obstacles
and cause a fall or tip over.
3. If you have to climb or descend a curb, or overcome an obstacle it
may be necessary to have an attendant make sure the anti-tip tubes
are rotated up, and out of the way, so that the chair and rider do
not get stuck and/or become unstable.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
B. ARMRESTS
WARNING
Armrests detach and will not bear the weight of this chair.
1. NEVER lift this chair by its armrests. They may come loose or break.
2. Lift this chair only by non-detachable parts of the main frame.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
C. CUS IONS & SLING SEATS
WARNING
1. Quickie sling seats and standard foam cushions are not designed for
the relief of pressure.
2. If you suffer from pressure sores or if you are at risk that they will
occur, you may need a special seat system or a device to control your
posture. Consult your doctor, nurse or therapist to find out if you
need such a device for your well-being.
3. Seat slings are not intended to be used as a direct seating surface. A
cushion or other seating surface should be placed on the sling
before use.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
D. FASTENERS
WARNING
Many of the screws, bolts and nuts on this chair are special high-strength
fasteners. Use of improper fasteners may cause your chair to fail.
1. ONLY use fasteners provided by an authorized supplier (or ones of
the same type and strength, as indicated by the markings on the
heads).
2. Over- or under-tightened fasteners may fail or cause damage to
chair parts.
3. If bolts or screws become loose, tighten them as soon as you can.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
Recommended Tire Pressures

MK-00084 Rev. A
13
QUI C KI E 7R
G. OFFSET SEATING (Option)
WARNING
1. A fore/aft change in the backrest position will affect the center of
balance of your chair.
2. Only use this option when installing a forward offset mounted seat-
ing solution, not using the standard back sling.
3. Each time you adjust or modify the backrest plane location, the
change may make it easier to tip backwards. Use anti-tips until you
adapt to the change, and are sure you are not at risk to tip over.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
. POSITIONING BELTS (Option)
WARNING
The positioning belt is predominately used to support your posture. It can
also be used to limit slipping and/or sliding that you might experience when
the chair is in motion. The positioning belt is not a transit rated safety belt
and should not be used in the place of a seat belt while being transported
in a motor vehicle. Improper use of Positioning belts may cause severe
injury or death. If you use a positioning belt, be sure to follow the recom-
mendations in this section:
1. Make sure the rider does not slide down in the wheelchair seat. If
this occurs, the rider may suffer chest compression or suffocate due
to pressure from the belts.
2. The belts must be snug, but must not be so tight that they interfere
with breathing. You should be able to slide your open hand, flat,
between the belt and the rider.
3. A pelvic wedge or a similar device can help keep the rider from slid-
ing down in the seat. Consult with the rider’s doctor, nurse or ther-
apist to find out if the rider needs such a device.
4. Use positioning belts only with a rider who can cooperate. Make
sure the rider can easily remove the belts in an emergency.
5. NEVER use positioning belts
a. As a patient restraint. A restraint requires a doctor’s order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the
rider may be thrown from the chair. Wheelchair positioning
belts will not prevent this, and further injury may result from the
belts or straps.
If you fail to heed these warnings, damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
I. PUS ANDLES (Option)
WARNING
When you have an attendant, make sure that this chair has push handles.
1. Push handles provide secure points for an attendant to hold the rear
of this chair, to prevent a fall or tip-over.
2. Check to make sure push handle grips will not rotate or slip off.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
J. QUICK-RELEASE AXLES
WARNING
1. Do not use this chair UNLESS you are sure that both quick-release
rear axles are locked.
2. An axle is not locked until the quick-release button pops out fully.
3. An unlocked axle may come off during use, resulting in a fall, tip-over
or loss of control and cause severe injury to the rider or others.
• Quick-Release Axles should be periodically cleaned and inspected
for function and signs of wear or bending. Replace as necessary.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
K. REAR W EELS
WARNING
A change in set-up of the rear wheels will affect the center of balance of
your chair.
1. The farther you move the rear axles FORWARD, the more likely it
is that your chair will tip over backward.
2. Consult your healthcare advisor to find the best rear axle set-up for
your chair. Do not change the set-up UNLESS you consult your health-
care advisor first.
3. Adjust the rear wheel locks after you make any change to the rear
axles.
a. If you fail to do so, the wheel locks may not work.
b. Make sure lock arms embed in the tires at least 1/8 inch when
locked.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
L. REAR W EEL LOCKS
WARNING
Rear wheel locks are NOT designed to slow or stop a moving wheelchair.
Use them only to keep the rear wheels from rolling when your chair is at a
complete stop.
1. NEVER use rear wheel locks to try to slow or stop your chair when
it is moving. Doing so may cause a fall or tip-over
2. To keep the rear wheels from rolling, always set both rear wheel
locks when you transfer to or from your chair.
3. Low pressure in a rear tire may cause the wheel lock on that side to
slip and may allow the wheel to turn when you do not expect it.
4. Make sure lock arms embed in tires at least 1/8 inch when locked. If
you fail to do so, the locks may not work.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
M. MODIFIED SEAT SYSTEMS
WARNING
Use of a seat system not approved by Sunrise may alter the center of bal-
ance of this chair. This may cause the chair to tip over.
1. Do not change the seat system of your chair UNLESS you consult
your authorized supplier first.
2. Use of a seating system not approved by Sunrise may affect the
backrest folding mechanism of this chair.
3. Use of a seating system not provided by Sunrise is prohibited for
transit use.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
VII . WARNI N G S : C OMPON E N T S & O PTION S

MK-100084 Rev. A 14
QUI C KI E 7R
WARNING
Do not use the Freestyle Adjustable backrest to push or lift the wheelchair.
Improper use may cause the back to unexpectedly detach from the wheel-
chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
Q. FOLDING LOCK DOWN ANGLE ADJUSTABLE
BACKREST
WARNING
Only adjust backrest angle when in a safe and stable position. You may
increase the likelihood of tipping or instability.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
R. SEAT BACK
WARNING
Adjusting the seat back depth could cause the strut tube to be located in a
position where it could contact the user and cause skin breakdown or other
serious injuries.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
N. SEAT AND BACK UP OLSTERY
WARNING
1. Replace worn or torn fabric of seat and seat back as soon as you
can. If you fail to do so, the seat or seat back may fail.
2. Sling fabric will weaken with age and use. Look for fraying, thin spots,
or stretching of fabrics especially at edges and seams.
3. “Dropping down” into your chair will weaken fabric and result in
the need to inspect and replace the seat more often.
4. Be aware that laundering or excess moisture will reduce the flame
retardation qualities of the fabric.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
O. BACKREST TENSION ADJUSTABLE
The Tension Adjustable Backrest is a versatile back intended to replace
standard wheelchair back upholstery. It is designed to provide simple, com-
fortable and effective support to help maximize function and increase seat-
ing tolerance. In addition, it is lightweight, durable, and easy to use.
Sunrise Medical recommends that a clinician such as a doctor or therapist
experienced in seating and positioning be consulted to determine if the
Backrest Tension Adjustable is appropriate. Backs systems should only be
installed by an authorized Sunrise Medical supplier.
Maximum user weight 265 lbs. (120 kg.)
WARNING
Installing a back support on a wheelchair may affect the center of gravity of
the wheelchair and may cause the wheelchair to tip backwards potentially
resulting in injury.
Always assess for the potential need for anti-tippers to be added to the
wheelchair to help increase the stability.
WARNING
Do not use the Backrest Tension Adjustable to push or lift the wheelchair.
Improper use may cause the back to unexpectedly detach from the wheel-
chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
P. FREESTYLE BACK (Option)
The Freestyle Adjustable Backrest is a versatile back intended to replace
wheelchair back upholstery. It is designed to provide simple, comfortable
and effective support to help maximize function and increase seating toler-
ance. In addition, it is lightweight, durable, and easy to use.
Sunrise Medical recommends that a clinician such as a doctor or therapist
experienced in seating and positioning be consulted to determine if the
Integral Adjustable Backrest is appropriate. Backs should only be installed
by an authorized Sunrise Medical supplier.
Maximum user weight 265 lbs. (120 kg.)
WARNING
Installing a back support on a wheelchair may affect the center of gravity of
the wheelchair and may cause the wheelchair to tip backwards potentially
resulting in injury.
Always assess for the potential need for anti-tippers to be added to the
wheelchair to help increase the stability.
VII . WARNI N G S : C OMPON E N T S & O PTION S

VIII. USE AND MAINTENANCE
MK-00084 Rev. A
15
QUI C KI E 7R
WARNING
The owner of this chair is responsible for making sure that it has been set
up and adjusted by a trained service professional under the advice of a
healthcare professional. The chair may require periodic safety and function
checks or certain in-use adjustments that can be performed by the owner,
caregiver or authorized dealer if desired. Always use parts and/or acces-
sories that have been recommended or approved by Sunrise Medical when
servicing this chair.
A. INTRODUCTION
1. Proper maintenance will improve performance and extend the useful
life of your chair.
2. Clean your chair regularly. This will help you find loose or worn
parts and make your chair easier to use. You will need a mild deter-
gent solution and plenty of cleaning rags.
3. If discovered, have loose, worn, bent or damaged parts replaced
before using the chair.
4. To protect your investment, have all major maintenance and repair
work done by your authorized dealer.
5. Inspect and maintain this chair strictly per the safety checklist.
6. If you detect a problem, make sure to order parts, or have service,
and repair work done at your authorized dealer before use.
7. At least once per year, have a complete inspection, safety check,
and service of your chair made by an authorized dealer.
B. CRITICAL SAFETY C ECKS
1. Tire Air Pressure:
Check air pressure in pneumatic tires at least ONCE PER WEEK. The
wheel locks will not grip properly if you fail to maintain the air pressure
shown on tire sidewall.
2. Axles & Axle Sleeves:
When checking axles and axle sleeves every six months, make sure they are
clean and tight. Loose sleeves will damage the axle plate and will affect
performance.
3. Camber Tubes and Camber Plugs
Inspect the camber tubes and plugs every 6 months ensuring that all fasten-
ers are tight and that no parts have moved from their preset positions.
C. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent at least once
a month.
b. Protect the paint with a coat of non-abrasive auto wax every three
months.
2. Axles and Moving Parts
a. Clean around axles and moving parts WEEKLY with a slightly damp
(not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or moving parts.
3. Upholstery
a. and-wash (machine washing may damage fabric).
b. Drip-dry only. DO NOT machine dry as heat will damage fabric.
4. Basic Maintenance Materials available at local store
a. Tire pump
b. Tire pressure gauge
c. Clean rags or cotton cloth.
d. Teflon-based lubricant
e Mild detergent.
NOTE – You do not need to grease or oil the chair.
Weekly 3 Months 6 Months Annually
RTire inflation level
RWheel locks
RVisually check for loose hardware
RArmrests
RAxle and axle sleeves
RQuick-release axles
RWheels, tires and spokes
RCasters
RAnti-tip tubes
RFrame, Camber tubes, and Crossbrace
RUpholstery
RService by Authorized Dealer
Safety & Function Check
D. SAFETY C ECKLIST
RRRR Make sure tire pressure is correct and
equal in both rear tires and front caster
tires, if pneumatic.
RRRR Make sure all nuts and bolts are tight.
RR Make sure all spokes and nipples are
tight on radial spoke wheels.
RUse Tri-Flow Lubricant (Teflon®-based)
between frame connections and parts.
RR R R Check for proper caster fork adjust-
ment. See instructions for caster fork
adjustment.
Symptom
Left turn in chair Right turn in chair Looseness in chair Sluggish turning Squeaks and rattles Caster flutter
Solution
E. TROUBLES OOTING C ART
NOTE - The user or caregiver should perform these weekly and
monthly checks to maintain the safety of their chair. If an item is
not working properly, please contact your authorized dealer.

MK-100084 Rev. A 16
QUI C KI E 7R
F. TO MOUNT & REMOVE REAR W EELS
WARNING
Do not use this chair UNLESS you are sure both quick-release axles are locked. An unlocked axle may come off
during use and cause a fall.
NOTE– Setting the wheelchair on a flat surface, such as a workbench or table, helps make these procedures
easier.
1. To Install Wheel
a. Depress quick-release button (A) fully.
b. Insert axle (B) through hub of rear wheel.
c. Keep button (A) depressed as you slide axle (B) into camber plug (C).
d. Release button to lock axle in camber plug. Adjust axle if it does not lock.
See Section B.
e. Repeat steps on other side.
2. To Remove Wheel
a. Depress quick-release button (A) fully.
b. Remove wheel by sliding axle (B) completely out of camber plug (C).
c. Repeat steps on other side.
NOTE– The axle is not locked until the quick-release button pops out fully (A). Check that the axle is locked
by pulling on the wheel in the direction of the axle.
G. W EEL LOCKS
WARNING
Wheel locks are installed at Sunrise and should be adjusted by your qualified service person.
Inspect wheel locks weekly per the maintenance chart. Do not use your chair UNLESS you are sure both
wheel-locks can fully engage. A wheel-lock that is not correctly adjusted may allow your chair to roll, or turn
unexpectedly.
Wheel-locks must be adjusted after making sure the tires have the correct air pressure. When fully engaged, the
arm (D) should be imbedded into the tire at least 1/8” to be effective.
If you find the wheel locks have slipped or are not working correctly contact your service provider for proper
adjustment.
. ANTI-TIPS
Sunrise Medical recommends anti-tip tubes for all wheelchairs.
1. Inserting Anti-tip Tubes Into Receiver
a. Press the rear anti-tip release button ( I ) on the anti-tip tube so that both release pins are
drawn inside.
b. Insert the anti-tip tube (E) into the anti-tip receiver (F).
c. Turn the anti-tip tube down until release pin is through the receiver mounting hole.
d. Insert second anti-tip tube the same way.
2. Adjusting Anti-Tip Tube Wheel
The anti-tip wheels may have to be raised or lowered to achieve proper clearance of
1 1/2" to 2".
Press the anti-tip wheel release button (G) so that both release pins are drawn inside. Raise or
lower to one of the three predrilled holes ( ). Release button. Adjust the second anti-tip tube
wheel the same way. Both wheels should be the same height.
3. Turning Anti-Tip Tubes Up
Turn anti-tip tubes up when being pushed by attendant, overcoming obstacles or climbing curbs.
Press the rear anti-tip tube release button ( I ). old lever in and turn anti-tip tube up. Release the
lever and repeat with second anti-tip tube. Remember to return anti-tip tubes to down position
after completing maneuver.
1211
13
14
VII I . U S E A ND MAIN T E N A NCE
11
12
A
B
C
13
D
14
F
G
E
I

MK-00084 Rev. A
17
QUI C KI E 7R VII I . U S E A ND MAIN T E N A NCE
I. SINGLE POST EIG T-ADJUSTABLE ARMRESTS (Option)
Sunrise medical offers several different types of armrests. Fixed, swing-away, and Flip-back armrests. Swing-away
armrests can be detached or can swing away to allow lateral transfers. They are height adjustable
(1" increments)
1. Basic Installation
a. Slide the outer armpost(1) into the receiver (7) mounted to the wheelchair frame.
b. The armrest should lock into place.
2. eight Adjustment
a. Release the upper securing lever. (2)
b. Slide armpad (4) up or down to desired height.
c. Return lever (2) to locked position.
3. Removing the Armrest
a. Squeeze the Release Lever (3) and remove the armrest from the receiver (7).
J. PADDED SWING-AWAY ARMRESTS (Option)
1. Installation
a. The armrest height is determined by the adjustment bolt (A) position.
b. Slide the armrest into the receiver tube (B) on rear of frame until the adjustment bolt
is securely seated (locked) in the receiver tube slot.
2. Swinging Away
a. Lift armrest out of the locked position and rotate to the side
3. Removing Armrest
a. Pull armrest straight out of the receiver.
J. FLIP-UP FOOTPLATE
The footplate (C) can be rotated up towards the user for transfers and adjustment.
K. FREESTYLE BACK(Option)
Back pad Installation
a. Wrap the Backpad (D) around the back shell (E) as shown.
b. Attach the Velcro straps so that the pad is secure.
WARNING
Make sure that your Authorized dealer, when doing regular maintenance, tightens the back hardware to the
torque specified in section IX-O. Do not use this chair UNLESS you are sure the adjustments are locked in to
this torque.
15
16
17
18
16
A
B
17
C
18
D
E
1. Outer armpost
2. eight Release Lever
3. Release lever
4. Armrest pad
5. Transfer bar
6. Side panel
7. Receiver
8. Receiver adjustment hardware
1
3
6
25
8
7
15
4

MK-100084 Rev. A 18
QUI C KI E 7R
L. BACK ANGLE PERFORMANCE
Adjusting the Angle of the Backrest
1. Release the backrest by pulling the adjustable tension pull cord (A) with a simple, short force.
2. While maintaining tension on the release cord, rotate the backrest to the desired angle, either forward or
rearward.
3. Lock the backrest in place by releasing the cord and allowing the pins (B) to engage in the nearest hole
(C) of the backrest bracket (D).
Folding and Unfolding the Backrest
1. Release the backrest by pulling the adjustable tension pull cord (A) with a simple, short force.
2. While maintaining tension on the release cord, rotate the backrest to unfold it. Remove the cushion and
push down hard to lock it in the folded position.
3. Lock the backrest in the folded position by removing your cushion. Release the pull-cord, and push down
hard allowing the pins (B) to engage in the folded position hole (E) of the backrest bracket (D).
WARNING
Be sure the pins (B) are fully engaged through the backrest bracket (D) on both sides of the chair,.
Test the backrest to be sure it is locked before use.
M. TENSION ADJUSTABLE UP OLSTERY
Installing standard Tension Adjustable Backrest Upholstery
1. Slide Velcro®straps (F) over the backrest frame (G) section. Make sure to include at least one
strap below the towel bar (if using a rigid chair).
2. Tighten the straps appropriately to desired tension level. DO NOT over tighten straps as this
will cause undue strain upon the chair backrest frame (G).
3. If using fold down push handles, insert the single Velcro®strap (F) through the slots in the
front of the push handles ( I ).
If using integral push handles ( J ), slide straps from bottom of backrest upward.
4. Install backrest cover at desired level and fold over rear of Velcro®strapping system (K). The
Quickie patch should be upright on the rear of the chair.
5. Finish installation by placing vanity flap (center panel) down onto Velcro®on the seat sling to
secure attachment (L).
WARNING
Any changes made to the straps will affect the center of gravity. It is best to have the attendant sta-
tioned behind the wheelchair to prevent the wheelchair from tipping backwards while the user
becomes accustomed to the adjustment.
24
23
2221
2019
VII I . U S E A ND MAIN T E N A NCE
22
23
21
24
K
F
I
G
J
F
L
20
D
B
E
C
19
A

MK-00084 Rev. A
19
QUI C KI E 7R
N. SEAT SLING ADJUSTMENT
Remove the screws (A) retaining the left side seat sling. Readjust VELCRO®-style material to
increase the tension in the seat sling. Replace screws. If there is any difficulty in reattaching the
screws, try using a probe to help align the holes. Ensure that the plastic saddles (B) are under the
seat rail in all fastener positions.
O. ULTRA LIG T SEAT SLING
The Ultra Light Seat Sling may be removed by first loosening the Velcro strap (C) on both the front
and rear of the seat upholstery cover (E). Then proceed by loosening all Velcro straps (D) that
encircle the chair frame. All straps must be reinstalled in the same position and quantity as the origi-
nal set-up.
P. CUS ION INSTALLATION
Place cushion on seat sling with VELCRO® side down. The beveled edge of the cushion should be in
front. Press firmly into place.
Q. STORAGE TIPS
1. Store your chair in a clean, dry area. If you fail to do so, parts may rust or corrode.
2. Before using your chair, make sure it is in proper working order.
3. Inspect and service all items on the “Maintenance Chart”.
4. If stored for more than three months, have your chair inspected by an authorized dealer
before use.
R. C ECK-OUT
After the wheelchair is assembled and adjusted, it should roll smoothly and easily. All accessories should also per-
form smoothly. If you have any problems, follow these procedures:
1. Review the set-up and check-out sections and operating guide to make sure chair was properly
prepared.
2. Review the troubleshooting chart at the beginning of this section.
3. If your problem persists, contact your authorized dealer. If you still have a problem after contacting your
authorized dealer, contact Sunrise customer service. See the Introduction Page for details on how to con-
tact your authorized dealer or Sunrise customer service.
26
25
VII I . U S E A ND MAIN T E N A NCE
25
26
C
D
E
B
A

IX. DEALER SERVICE AND ADJUSTMENT
MK-100084 Rev. A 20
QUI C KI E 7R
WARNING
The owner of this chair is responsible for making sure that it has been setup and adjusted by a trained service
professional under the advice of a healthcare professional. Service and/or adjustments should only be done
with the advice of a healthcare professional. Always use parts and/or accessories that have been recommended
and approved by Sunrise Medical when servicing this chair.
A. DEALER SERVICE INTRODUCTION
1. At least once per year, this chair should have a complete inspection, safety check, and regular service
made by an authorized dealer. The tool list at right is a good starting point for proper maintenance.
2. If you have discovered a worn, bent, or damaged part, repair or replace them with recommended parts
before returning this chair to service.
3 All major maintenance and repair work should be done by the authorized dealer.
B. CRITICAL MAINTENANCE TIPS
1. Torque settings:
A torque setting is the optimum tightening which should be made on a particular fastener. It is important to use
proper torque settings where specified. When not specified, torque settings should be 60 in-lbs
2. Dealer Service and Adjustment Reference materials:
Go to www.sunrisemedical.com for parts manuals, instruction sheets, and instructional videos that will aid in the
repair of your Quickie wheelchair.
C. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent.
b. Protect the paint with a coat of non-abrasive auto wax.
2. Axles and Moving Parts
a. Clean around axles and moving parts with a slightly damp (not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or moving parts.
c. DO NOT USE 3-in-ONE oil, or WD-40®for lubrication. Only use Teflon based Lubricant when working
on this wheelchair.
D. REAR W EEL AXLE NUT ADJUSTMENT
The rear wheel axle (B) attaches the rear wheel (D) to the camber plug (C). When the detent balls (E) engage
into the camber plug the rear wheel effectively becomes locked onto the chair. Pushing the quick-release button
(A) disengages the detent balls and allows removal of the axle and wheel assembly.
To adjust the axle you will need a 3/4" wrench to turn the adjustment nut (F). You will also need a 1/2" wrench
to securely hold the ball detent end of the axle to prevent it from turning.
If the wheel and axle will not lock into the camber plug then the axle requires adjustment. Turn the nut counter-
clockwise approximately 1/4 revolution and try to lock the axle into the camber plug. If it doesn't lock, continue
making small nut adjustments until it securely locks.
If the wheel is locked on the chair but there is excessive wheel play (the wheel hub can be pushed back and
forth on the axle) then adjust the nut clockwise until there is no perceptible gap between the wheel and camber
tube and the axle is securely locked onto the chair.
E. ANTI-TIP RECEIVER
Sunrise Medical recommends anti-tip tubes for all wheelchairs.
a. After attaching the Anti-tip receiver (G) make sure that the receiver is parrallel with the
ground, and the bolts are tightened so that the anti-tips don’t move when used.
b. Make sure that the guide/locking pins are engaged before use.
27
2928
30
28
29
TOOLS YOU WILL NEED
1. Imperial ex key set
2. Metric ex key set
3. Imperial Open-end Wrench set
4. Metric Open-end Wrench set
5. Torque wrench
6. Imperial ex bit Socket set
7. Metric ex bit Socket set
8. Phillips and Flat screwdrivers
9. Tire Pressure Gauge
A
B
C
D
E
F
A
E
27
30
G