Sunrise Medical Quickie Pulse Series User manual

O w n e r ’ s M a n u a l
Quickie®Pulse
6 BC, 6 SC, 6 CC, 5 BC, 5CC
SUPPLI R: This manual must be given to the rider of this wheelchair.
RID R: Before using this wheelchair read this entire manual and save
for future reference.
M o d e d ’ e m p l o i
Quickie®Pulse
6 BC, 6 SC, 6 CC, 5 BC, 5CC
FOURNISS UR: Ce manuel doit être remis à l’utilisateur / utilisatrice de
ce fauteuil roulant.
UTILISAT UR / UTILISATRIC :Avant d’utiliser ce fauteuil roulant, lisez
entièrement ce manuel et conservez le pour le consulter ultérieure-
ment.
Chaque fauteuil est livré avec un manuel d’instructions en anglais. Les versions en espagnol
et en français sont à votre disposition en format PDF sur le site :
www.SunriseMedical.com. Veuillez vous rendre à la page de votre produit pour télécharger
le manuel dans la langue souhaitée, ou contactez un fournisseur agréé Sunrise Medical.
M a n u a l d e I n s t r u c c i o n e s
Quickie®Pulse
6 BC, 6 SC, 6 CC, 5 BC, 5CC
DISTRIBUIDOR: ste manual debe ser entregado al pasajero de esta silla
de ruedas.
PASAJ RO: Antes de usar esta silla de ruedas, lea este manual en su totali-
dad y guárdelo para futura referencia.
Cada una de las sillas se envía con un manual de instrucciones en inglés. l manual en español
o francés está disponible en formato PDF en nuestra página en Internet:
www.SunriseMedical.com. Ingrese a la página del producto específico para descargar el manu-
al, o comuníquese con el proveedor autorizado de Sunrise Medical.
S E C T I O N E N G L I S H
P U L S E
All manuals and user guides at all-guides.com
all-guides.com

119832 Rev. B 2
NGLISH
I. INTRODUCTION
I. INTRODUCTION
SUNRIS LIST NS
Thank you for choosing a Quickie wheelchair. We want to hear your
questions or comments about this manual, the safety and reliability
of your chair, and the service you receive from your Sunrise supplier.
Please feel free to write or call us at the address and telephone
number below:
SUNRIS M DICAL
Customer Service Department
2842 Business Park Ave
Fresno, CA 93727
[phone] or [phone]
FOR ANSW RS TO YOUR QU STIONS
Your authorized supplier knows your wheelchair best and can
answer most of your questions about chair safety, use and mainte-
nance. For future reference, fill in the following:
Supplier: _______________________________________________________________
Address: _______________________________________________________________
______________________________________________________________________
Telephone: _____________________________________________________________
Serial #: _________________________________________ Date/Purchased: ________
US R WARNING
WARNING
Attention wheelchair users, do not operate this wheelchair
without first reading the owner’s manual. If you do not under-
stand the instructions and warnings of this owner’s manual
please contact your dealer or qualified technician before
operating this Quickie wheelchair. Failure to do so may result
in damage and/or injury.
D AL R/T CHNICIAN WARNING
WARNING
Attention dealers and qualified technicians, do not operate or
service this wheelchair without first reading this owners manu-
al. If you do not understand the instructions and warnings of
this owners manual please contact the Quickie Technical
Service Department before operating and/or servicing this
Quickie wheelchair. Failure to do so may result in damage
and/or injury.
WARNING
In addition, power wheelchairs may contain printed circuit
boards. Careful attention should be given to the Printed
Circuit Board Handling Techniques insert supplied with the
chair.
Related Documents
Listed below are additional documents which are referenced in this
owners manual.
• RN T Owners Manual
• RN T OBP Owners Manual
• RN T Omni Owners Manual
• Pulse Service Manual
All manuals and user guides at all-guides.com

119832 Rev. B
3
NGLISH
II. TABLE OF CONTENTS
I. INTRODUCTION..........................................................................2
III. YOUR CHAIR AND ITS PARTS ................................................4
IV. NOTIC – R AD B FOR US ...................................................5
V. MI ( L CTROMAGN TIC INT RF R NC ).......................5
A.WHAT IS MI? ............................................................................5
B. WHAT FF CT CAN MI HAV ?.........................................5
C.SOURC S OF MI .....................................................................5
D.DISTANC FROM TH SOURC ..........................................6
. IMMUNITY L V L .....................................................................6
F. R PORT ALL SUSP CT D MI INCID NTS ....................6
VI. G N RAL WARNINGS................................................................7
A.NOTIC TO RID R...................................................................7
B. NOTIC TO ATT NDANTS ...................................................7
C.W IGHT LIMIT ..........................................................................7
D.CONTROLL R S TTINGS......................................................7
. MI .................................................................................................7
F. SAF TY CH CK-LIST...............................................................7
G.CHANG S & ADJUSTM NTS ................................................7
H.WH N S AT D IN A PARK D WH LCHAIR ................8
I. NVIRONM NTAL CONDITIONS......................................8
J. T RRAIN........................................................................................8
K.STR T US ................................................................................8
L. MOTOR V HICL SAF TY......................................................8
M.C NT R OF BALANC ...........................................................8
N.TRANSF RS.................................................................................8
O.R ACHING OR L ANING .....................................................9
P. DR SSING OR CHANGING CLOTH S.............................9
Q.OBSTACL S.................................................................................9
R. DRIVING IN R V RS .............................................................9
S. RAMPS, SLOP S & SID HILLS................................................9
T. TO R DUC TH RISK OF A FALL, TIP-OV R
OR LOSS OF CONTROL .....................................................10
U. RAMPS AT HOM & WORK................................................10
V. WH LCHAIR LIFTS..............................................................10
W.CURBS & SINGL ST PS ......................................................10
X.STAIRS.........................................................................................10
Y. SCALATORS ...........................................................................10
VII. WARNINGS: COMPON NTS & OPTIONS........................11
A.ARMR STS.................................................................................11
B. BATT RI S.................................................................................11
C.CUSHIONS................................................................................11
D.FAST N RS ...............................................................................11
. FOOTPLAT & FOOTR STS................................................11
F. MOTOR LOCKS ......................................................................11
G.ON/OFF SWITCH...................................................................11
H.POSITIONING B LTS ...........................................................11
I. S ATING SYST MS .................................................................11
J. UPHOLST RY FABRIC...........................................................12
K.SUSP NSION............................................................................12
L. WIRING .....................................................................................12
M.POW R S ATING ...................................................................12
N.S.P.O.T. (SINGL POW R OPTION TILT)
POW R ACC SSORY.............................................................12
O.TRANSIT OPTION .................................................................12
VIII. S T-UP, ADJUSTM NT & US .................................................16
TOOLS YOU WILL N D .........................................................16
A.BATT RY R MOVAL...............................................................17
B. C NT R MOUNT HANG R ADJUSTM NT ..................17
C.SWING-AWAY FOOTR STS................................................18
D. L VATING L GR ST ............................................................18
. FOLDING BACKR ST ...........................................................18
F. DUAL-POST H IGHT-ADJUSTABL ARMR STS FIX D
H IGHT STANDARD............................................................19
G.SINGL POST H IGHT-ADJUSTABL ARMR STS ........19
H.ASAP S AT D PTH 14" - 16", 20" - 22" ONLY...............19
I. CAPTAIN’S S AT.....................................................................20
J. MANUAL R CLIN OP RATION ......................................22
K.JOYSTICK .................................................................................22
L. JOYSTICK R TRACTABL MOUNT ................................23
M.ASAP II S ATING ADJUSTM NT........................................23
N.S AT H IGHT ADJUSTM NT..............................................23
O.S AT R MOVAL ......................................................................23
P. SHROUD R MOVAL .............................................................24
Q.CONTROLL R POSITION .................................................24
R. CH CK-OUT............................................................................24
IX. OP RATING GUID ...................................................................25
A.P RFORMANC CONTROL S TTINGS..........................25
B. TH RMAL ROLL-BACK .......................................................25
C.JOYSTICK STATIONARY.......................................................25
D.VR2 JOYSTICK ASS MBLY ....................................................26
. L D JOYSTICK..........................................................................27
F. MONOCHROM LCD SCR N.........................................28
G. COLOR LCD SCR N..........................................................29
H.BRAK L V R .........................................................................30
X. BATT RI S.....................................................................................31
A.INTRODUCTION ..................................................................31
B. BATT RY CHARG R ............................................................31
C. ACID BURNS (UNS AL D W T C LL BATT RI S)....31
D. CONN CTING BATT RI S IN BATT RY W LL .........31
. CHARGING BATT RI S .......................................................32
F. DISPOSING OF BATT RI S.................................................32
XI. MAINT NANC ...........................................................................33
A.NOT S ......................................................................................33
B. CL ANING ..............................................................................33
C.STORAG TIPS ........................................................................33
D.TO R PAIR OR R PLAC A TIR .......................................33
. MOTOR BRUSH S .................................................................33
F. ORD RING PARTS .................................................................33
G. MAINT NANC CHART.....................................................33
H. WIRING DIAGRAM................................................................34
XII. SUNRIS LIMIT D WARRANTY.............................................35
SPAÑOL .......................................................................................36
FRANÇAIS......................................................................................70
All manuals and user guides at all-guides.com

III. YOUR CHAIR AND ITS PARTS
Weight
SC BC CC
complete chair: 260 lbs 235 lbs 250
w/o batteries: 182 lbs 157 lbs 172
Drive Wheels
13" Mag: Std. airless insert
Joystick
Standard – VR2 (right-hand or
left-hand mount)
Option - VR2 w/actuator control
(SC only)
Option - RN T–
L D/Monochrome/Color
Batteries
(2 deep cycle batteries required to
operate chair)
Standard - Group 22
Battery Charger
Off board 8 AMP
Shroud Colors
Red, Black, Blue
Seats, Upholstery and Style
Standard- BC & SC: A.S.A.P. II Seat Frame
CC: Captain’s Seat
Sizes: 12" - 22" wide, 12" - 22" deep
Footrest:
CC- Center Mount
SC & BC: Standard- SA Swing away
footrests with heel loops
Option- Foot platform, Manual ele-
vating legrests, Power Articulating
Legrest (ALR), Power Center Mount,
Center Mount
Backrest
SC & BC: Standard Canes Angle
Adjustable
Option- 8° Bend, Semi Recline,
Folding
CC: Standard- Captain’s Seat Back
Casters (front)
Standard- 7” solid
Casters (rear)
Standard- 6” solid
Armrest
SC & BC: Standard- 14" Cantilever, height
adjustable 14" arm pad
Option- Locking, two-point arm, Dual
post Arm, Single Post arm
CC: Standard- Flip-up
Suspension
Standard- all wheel
All features may not be available with some
chair setups or in conjunction with another
chair feature. Please consult your supplier
for more information. Your authorized sup-
plier can also provide you with more infor-
mation on accessories.
QUICKIE PULSE
III. YOUR CHAIR AND ITS PARTS
NGLISH
4
119832 Rev. B
1. Flip-back, height-adjustable armrest
2. VR2 controller joystick
(RN T optional)
3. Captain’s Seat
4. Front caster 7"
5. Rear stabilizing caster 6"
6. Single plate foot platform (shown);
Optional:
Swing-away 65° Hangers;
Swing-away LR hangers
Swing-away 70° Hangers;
(tapered) Swing-away 75° Hangers;
Swing-away 90° Hangers;
7. Drive wheels
8. Brake release
9. Caster Fork (front)
10. Caster Fork (rear)
11. Front Shroud
Models
Pulse 6 BC
Pulse 6 SC
Pulse 6 CC (shown)
Pulse 5 BC
Pulse 5 CC
1
3
6
4
8
9
11 7
5
10
2
All manuals and user guides at all-guides.com

V. EMI (ELECTROMAGNETIC INTERFERENCE)
V. EMI (ELECTROMAGNETIC INTERFERENCE)
WARNING
Heed all warnings to reduce the risk of unintended brake
release or chair movement:
1. Beware of the danger from hand-held transceivers. (A
“transceiver” is a device that both sends and receives radio
wave signals). Never turn on or use a hand-held transceiver
while power to your chair is on. Use extra care if you
believe that such a device may be in use near your chair.
2. Be aware of nearby radio or TV stations, and avoid coming
close to them.
3. If unintended movement occurs, turn your chair off as soon
as it is safe to do so.
A. WHAT IS MI?
WARNING
1. MI means: electromagnetic ( M) interference (I). MI comes
from radio wave sources such as radio transmitters and
transceivers.
2. There are a number of sources of intense MI in your daily
environment. Some of these are obvious and easy to avoid.
Others are not, and you may not be able to avoid them.
3. Powered wheelchairs may be susceptible to electromagnetic
interference ( MI) emitted from sources such as radio sta-
tions, TV stations, amateur radio (HAM) transmitters, two
way radios, and cellular phones.
4. MI can also be produced by conducted sources or electro-
static discharge ( SD).
B. WHAT FF CT CAN MI HAV ?
WARNING
1. MI can cause your chair, without warning, to:
• Release its brakes
• Move by itself
• Move in unintended directions
If any of these occurs, it could result in severe injury to you or
others.
2. MI can damage the control system of your chair. This could
create a safety hazard, and lead to costly repairs.
C. SOURC S OF MI
WARNING
The sources of MI fall into three broad types:
1. Hand-Held Transceivers:
The antenna is usually mounted directly on the unit. These
include:
• Citizens band (CB) radios
• “Walkie-talkies”
• Security, fire and police radios
• Cellular phones
• Lap-top computers with phone or fax
• Other personal communication devices
NOT – These devices can transmit signals while they are on, even if not in use.
2. Medium-Range Mobile Transceivers:
These include two-way radios used in police cars, fire trucks,
ambulances and taxi cabs. The antenna is usually mounted on the
outside of the vehicle.
C. R VI W THIS MANUAL OFT N
Before using this chair you, and each person who may assist you,
should read this entire Manual and make sure to follow all instruc-
tions. Review the warnings often, until they are second nature to you.
D. WARNINGS
The word “WARNING” refers to a hazard or unsafe practice that
may cause severe injury or death to you or to other persons. The
“Warnings” are in four main sections, as follows:
1. V — MI
Here you will learn about electromagnetic interference and
how it can affect your chair.
2. VI — G N RAL WARNINGS
Here you will find a safety checklist and a summary of risks
you need to be aware of before you ride this chair.
3. VII — WARNINGS — COMPON NTS & OPTIONS
Here you will learn about your chair. Consult your supplier
and your health care professional to help you choose the
best set-up and options for your safety.
4. X — BATT RI S
Here you will learn about battery and charger safety, and
how to avoid injury.
NOT – Where they apply, you will also find “Warnings” in other sections of this
Manual.
IV. NOTICE– READ BEFORE USE
A. CHOOS TH RIGHT CHAIR & SAF TY
OPTIONS
Sunrise provides a choice of many power wheelchair styles, sizes
and adjustments to meet the needs of the rider. However, final
selection of a wheelchair rests solely with you and your health
care professional. Choosing the best chair for you depends on such
things as:
1. Your size, disability, strength, balance and coordination.
2. Your intended use, and your level of activity.
3. The types of hazards you must overcome in daily use (in
areas where you are likely to use your chair).
4. The need for options for your safety and comfort (such as
positioning belts or special seat systems).
B. ADJUST CHAIR TO YOUR ABILITY
You need to work with your doctor, nurse or therapist, and your
supplier, to fit this chair and adjust the controller settings for your
level of function and ability.
IV. NOTICE– READ BEFORE USE
NGLISH
5119832 Rev. B
All manuals and user guides at all-guides.com

F. R PORT ALL SUSP CT D MI
INCID NTS
WARNING
You should promptly report any unintended movement or
brake release. Be sure to indicate whether there was a radio
wave source near your chair at the time. Contact: Sunrise
Medical Customer Service Department at [phone].
3. Long-Range Transceivers:
These include commercial radio and TV broadcast antenna towers
and amateur (HAM) radios. Note: The following are not likely to
cause MI problems: Lap-top computers (without phone or fax),
Cordless phones, TV sets or AM/FM radios, CD or tape players.
D. DISTANC FROM TH SOURC
WARNING
M energy rapidly becomes more intense as you get closer to
the source. For this reason, MI from hand-held devices is of
special concern. (See C.1 above) A person using one of these
devices can bring high levels of M energy very close to your
chair without you knowing it.
. IMMUNITY L V L
WARNING
1. The level of M energy is measured in volts per meter
(V/m). very power wheelchair can resist MI up to a certain
level. This is called its “immunity level”.
2. The higher the immunity level, the less the risk of MI. It is
believed that a 20 V/m immunity level will protect the power
wheelchair user from the more common sources of radio
waves.
3. The Quickie Pulse with the following configuration was test-
ed and found to be immune to at least 20 V/m:
Quickie Pulse power wheelchair with a right-hand mounted
RN T controller, A.S.A.P. seat, flip-back armrests, solid flip-up
footplate and Group 22 batteries.
4. The following specialty input devices have an unknown effect on
the immunity level because they have not been tested with the
Quickie Pulse and RN T control system:
WARNING
Individuals with physical limitations requiring the use of a spe-
cialty control input device known not to be immune to
20V/m, or not known, should exercise extra care around
known sources of MI.
WARNING
There is no way to know the effect on MI if you add acces-
sories or modify this chair. Any change to your chair may
increase the risk of MI. Parts from other suppliers have
unknown MI properties.
V.
NGLISH
6
119832 Rev. B
All manuals and user guides at all-guides.com
all-guides.com

D. CONTROLL R S TTINGS
WARNING
Be aware that you may need to adjust the controller settings
of your chair to reduce the risk of a collision, fall or tip-over.
1. Check and adjust the settings every six to twelve months (or
more often, if needed).
2. Consult your supplier to adjust the control settings immedi-
ately if you notice any change in your ability to:
• Control the joystick.
• Hold your torso erect.
• Avoid running into objects.
. MI
WARNING
Read Section V to learn about MI. To reduce the risk of unin-
tended brake release or chair movement:
1. Never turn on or use a hand-held transceiver while power
to your chair is on. Use extra care if you believe that such a
device may be in use near your chair.
2. Be aware of nearby radio or TV stations, and avoid coming
close to them.
3. If unintended movement or brake release occurs, turn your
chair off as soon as it is safe.
F. SAF TY CH CK-LIST
WARNING
Before each use of this chair:
1. Make sure the chair operates smoothly. Check for noise, vibra-
tion, or a change in ease of use. (They may indicate low tire
pressure, loose fasteners, or damage to your chair). If you
detect a problem, make sure to repair or adjust the chair.
Deferring repair or adjustment could increase the risk for
injury. Your supplier can help you find and correct the problem.
2. Make sure batteries are charged. Green lights on the con-
troller charge indicator will light up when charge is full.
Yellow lights indicate battery charge level is getting low. Red
lights indicate batteries are in immediate need of charging.
G. CHANG S & ADJUSTM NTS
WARNING
Never use non-Quickie parts or make changes to your chair
unless authorized by Sunrise. (Doing so will void the Warranty
and may create a safety hazard).
1. If you modify or adjust this chair it may increase the risk of a
fall or tip-over.
2. Modifications unauthorized by Sunrise constitutes remanufac-
turing of the wheelchair. This voids the warranty. The rider
then assumes all future liability for the wheelchair.
VI. GENERAL ARNINGS
WARNING
Heed all warnings in this section. If you fail to do so a fall, tip-
over or loss of control may occur and cause severe injury to
you or others.
A. NOTIC TO RID R
WARNING
1. Before using this chair, you should be trained in its safe use
by your health care professional.
2. very wheelchair is different. Take the time to learn the feel
of this chair before you begin riding.
3. Be aware that you must develop your own methods for the
safe use of this chair that are best suited to your level of
function and ability.
4. Have someone help you practice bending, reaching and trans-
ferring until you learn how to do them safely.
5. Never try a new maneuver on your own unless you are sure
it is safe.
6. Get to know the areas where you plan to use your chair.
Look for hazards and learn how to avoid them.
7. Do not allow additional riders on the chair, armrests or
chassis. Doing so may result in injury or damage.
B. NOTIC TO ATT NDANTS
WARNING
Make sure you heed all warnings and follow all instructions in
each section of this manual. (Be aware that warnings that
apply to the rider also apply to you).
Notes:
1. You need to work with the rider and the rider’s doctor,
nurse or therapist, to develop safe methods best suited to
your abilities and those of the rider.
2. To manually push the chair you must release the motor
locks.
Make sure you have full control over the chair when you
release the motor locks. When you do so the chair will not
have brakes.
3. Propel this chair by the armrest supports only. If using a seat
frame, propel the chair by the push handles on the top of
the backrest. They provide secure points for you to hold the
rear of the chair to prevent a fall or tip-over.
C. W IGHT LIMIT
WARNING
1. Never exceed a total weight of 300 pounds (136.3 kilograms)
for rider plus items carried.
2. Never use this chair for weight training if the total weight
(rider plus additional weights) exceeds 300 pounds (136.3
kilograms).
3. xceeding the weight limit is likely to damage the seat, frame,
or fasteners and may cause severe injury to you or others
from chair failure.
4. xceeding the weight limit will void the warranty.
VI. GENERAL ARNINGS
NGLISH
7119832 Rev. B
All manuals and user guides at all-guides.com

VI.
H. WH N S AT D IN A PARK D
WH LCHAIR
WARNING
1. Always turn off all power to your chair when you are
parked, even for a moment. This will prevent:
• Accidental movement from contact with the joystick by you
or others.
• Unintended brake release or movement from MI sources.
(See Section V)
2. Make sure that persons who help you (for example, store
clerks) are aware of the joystick and do not touch it. If they
do, your chair may move suddenly when you do not expect
it.
I. NVIRONM NTAL CONDITIONS
WARNING
Your chair is not designed for use in a heavy rain storm, or in
snowy or icy conditions.
1. Contact with water or excessive moisture can cause an elec-
trical malfunction. The frame, motors and other chair parts
are not watertight and may rust or corrode from the inside.
To avoid a chair failure:
• Minimize exposure of your chair to a rain storm or very
wet conditions.
• Never take your chair into a shower, tub, pool or sauna.
• Do not use your chair in fresh or salt water (such as at
the edge of a stream, lake, or ocean).
• Make sure shroud cover and deck lid are secure.
• Replace joystick boot if it becomes torn or cracked.
• Make sure all electrical connections are secure.
• Dry the chair as soon as you can if it gets wet, or if you
use water to clean it.
2. Proceed slowly and use extra care if you must operate your
chair on a wet or slick surface.
• Do so only if you are sure it is safe.
• Stop if one or both main wheels lose traction. If this
occurs, you may lose control of your chair or fall.
• Never operate your chair on a slope or ramp if there is
snow, ice, water or oil film present.
• When in doubt, have someone help you.
3. When not in use, keep your chair in a clean, dry place.
J. T RRAIN
WARNING
1. This chair is designed for use on firm, even surfaces such as
concrete, asphalt and indoor flooring.
2. Do not operate your chair in sand, loose soil or over rough
terrain. Doing so may damage wheels, bearings, axles or
motors, or loosen fasteners.
K. STR T US
WARNING
In most states, power chairs are not legal for use on public
roads. Be alert to the danger of motor vehicles on roads or in
parking lots.
1. At night, or when it is hard to see, use reflective tape on
your chair and clothing.
2. It may be hard for drivers to see you. Make eye contact with
drivers before you proceed. When in doubt, yield until you
are sure it is safe.
L. MOTOR V HICL SAF TY
WARNING
To date, the U.S. Department of Transportation has not
approved any tie down system for transporting this wheel-
chair in a motor vehicle.
1. Never sit in this chair while in a moving vehicle. In an acci-
dent or sudden stop you may be thrown from the chair.
• Wheelchair belts are designed to position the rider only
and will not protect you in an accident; further injury
may result from the belts.
2. Always move to an approved vehicle seat. You must be
secured with proper motor vehicle restraints.
3. Never transport this chair in the front seat of a vehicle. It
may shift and interfere with the driver.
4. Always secure this chair so that it cannot roll or shift.
M. C NT R OF BALANC
WARNING
The point where this chair will tip forward, back or to the
side depends on its center of balance and stability.
The Center Of Balance Is Affected By:
1. The seat height and seat angle.
2. A change in your body position, posture or weight distribu-
tion.
3. Using this chair on a ramp or slope.
4. The use of a back pack or other options, and the amount of
added weight.
To Reduce The Risk Of A Fall Or Tip-Over:
1. Consult your supplier for information on modifications
authorized by Sunrise before you modify or adjust this chair.
NOT – You may need to make additional changes to correct the center of
alance.
2. Use extreme care until you know the balance points of this
chair and how to avoid a fall or tip-over.
N. TRANSF RS
WARNING
It is dangerous to transfer on your own. It requires good bal-
ance and agility. Be aware that there is a point during every
transfer when the wheelchair seat is not below you. To avoid a
fall:
1. Always turn off power before you transfer to or from your
chair. If you fail to do so you may touch the joystick and
cause your chair to move when you do not expect it.
NGLISH
8
119832 Rev. B
All manuals and user guides at all-guides.com

VI.
P. DR SSING OR CHANGING CLOTH S
WARNING
Be aware that your weight will shift if you dress or change
clothes while seated in this chair. To make the chair more sta-
ble, rotate the front casters until they are forward.
Q. OBSTACL S
WARNING
Obstacles you may have to overcome in daily use include
door thresholds, lifts, ramps and hazards such as potholes and
broken pavement. These can damage your chair and may cause
a fall, tip-over or loss of control.
1. Be aware that thresholds are very dangerous. ( ven a small
change in height may stop a caster wheel and cause your
chair to tip). You may need to:
• Remove or cover threshold strips between rooms.
• Install a ramp at entry or exit doors.
2. Keep your eyes moving when you ride; scan the area well
ahead of your chair.
3. Make sure the floor areas where you use this chair are level
and free of obstacles.
4. To help correct your center of balance:
• Lean your upper body forward slightly as you go up over
an obstacle.
• Press your upper body backward as you go down from a
higher to a lower level.
R. DRIVING IN R V RS
WARNING
Use extra care when you drive your chair in reverse. You may
lose control or fall if one of the rear wheels hits an object.
1. Operate your chair slowly and at an even speed.
2. Stop often and check to make sure your path is clear of
obstacles.
S. RAMPS, SLOP S & SID HILLS
WARNING
The center of balance of your chair changes when you are on
a slope.
NOT – “Slope” includes a ramp or sidehill. Your chair is less sta le when it is
at an angle. Never use this chair on a slope unless you are sure it is
safe. When in dou t, have someone help you.
Beware Of:
1. Steep slopes. Do Not use this chair on a slope steeper than
10%. (A 10% slope means: One foot in elevation for every
ten feet of slope length).
2. Wet or slippery surfaces (such as when ice, snow, water or
oil film is present). A loss of traction may cause a fall or tip-
over.
3. A change in grade on a slope (or a lip, bump or depression).
These may cause a fall or tip-over.
4. A drop-off at the bottom of a slope. (A drop-off of as small
as 3/4 inch can stop a front caster and cause the chair to tip
forward).
2. Make sure motor locks are engaged. This keeps the chair
from moving when you transfer.
3. Work with your health care professional to learn safe meth-
ods.
• Learn how to position your body and how to support
yourself during a transfer.
• Have someone help you until you are sure you can do a
safe transfer on your own.
4. Move your chair as close as you can to the seat you are
transferring to. If possible, use a transfer board.
5. Rotate the front casters until they are as far forward as
possible.
6. Be careful of the foot platform. If you can, remove or swing it
out of the way.
• Never stand on footrests when you transfer. Doing so
may damage them or cause your chair to tip.
• Make sure your feet do not “hang up” or get caught in
the space between the footrests.
7. Make sure armrests do not interfere.
8. Transfer as far back onto the seat surface as you can. This
will reduce the risk that you will miss the seat or fall.
O. R ACHING OR L ANING
WARNING
Reaching or leaning affects the center of balance of your chair. If
done improperly, a fall or tip-over is likely. When in doubt, ask for
help or use a device to extend your reach.
To Reduce the Risk of injury and/or Damage to the Chair:
1. Never reach or lean if you must shift your weight sideways
or rise up off the seat.
2. Never reach or lean if you must move forward in your seat
to do so. Always keep your buttocks in contact with the
backrest.
3. Never reach with both hands (you may not be able to catch
yourself to prevent a fall if you lose your balance).
4. Never try to pick up an object from the floor by reaching
down between your knees.
5. Never put pressure on the foot platform while reaching. This
may cause the chair to tip if you lean too far.
6. Never reach or lean over the top of the seat back. This may
damage the backrest and cause you to fall.
IF YOU MUST R ACH OR L AN, DO SO AT YOUR
OWN RISK.
Remember to:
1. Move your chair as close as you can to the object you wish
to reach.
2. Rotate the front casters until they are as far forward as pos-
sible. This makes the chair more stable.
Note– To do this: Move your chair past the object you want to reach,
then back up alongside it. Backing up will rotate the casters
forward.
3. Turn off all power to your chair. If you fail to do so, you may
touch the joystick and cause your chair to move when you
do not expect it.
4. Firmly grasp an armrest with one hand. This will help to pre-
vent a fall if the chair tips.
NGLISH
9119832 Rev. B
All manuals and user guides at all-guides.com

VI.
T. TO R DUC TH RISK OF A FALL,
TIP-OV R OR LOSS OF CONTROL
WARNING
1. Never use your chair on a slope unless you are sure you can
do so without losing traction.
2. Always go as straight up and as straight down as you can.
• Do not “cut the corner” on a slope or ramp.
• Do not turn or change direction on a slope.
3. Always stay in the center of the ramp. Make sure ramp is
wide enough that you are not at risk that a wheel may roll
off the side.
4. Lean or press your body uphill. This will help adjust for a
change in the center of balance caused by the slope.
5. Keep your chair moving at a slow, steady speed. Keep control
over the chair at all times.
• On a descent, do not let your chair accelerate beyond its
normal speed.
• If the chair picks up speed, center the joystick to slow
down or stop.
NOT – The solid state controller of your chair has a logic system that will
help control your speed when driving on a slope or uphill.
• If you stop, re-start slowly.
U. RAMPS AT HOM & WORK
WARNING
Make sure ramps meet all Building Codes for your area.
1. For your safety, have a licensed contractor build or remodel
ramp to meet all standards.
2. NOT – The proper design will vary, depending on such
things as: the length and height of the ramp; the need for an
intermediate platform; landing size; doors and the direction
of swing; and whether the ramp includes a turn or angle.
At A Minimum:
1. Open sides of ramp must have side rails to prevent your
chair from going over the edge.
2. Slope must not be steeper than one inch in height for every
one foot of slope length.
3. Ramp surface must be even, and have a non-skid surface.
4. You may need to add a section at the top or bottom to
avoid a lip or drop-off.
5. Ramp must be sturdy. Add bracing if needed, so ramp does
not “bow” when you ride on it.
V. WH LCHAIR LIFTS
WARNING
Wheelchair lifts are used in vans, buses, and buildings to help
you move from one level to another.
1. Always turn off all power to your chair when you are on a
lift. If you fail to do so, you may touch the joystick by accident
and cause your chair to drive off the platform. (Be aware that
a “roll-stop” at the end of the platform may not prevent this).
2. Make sure there is not a lip or drop-off at the top or bot-
tom of the platform. These may cause a fall or tip-over. When
in doubt, have someone help you.
3. Always secure the rider with a positioning belt to help pre-
vent falls during transfers.
4. Avoid moving forward if a wheel is “hung up” on the lip of
the ramp. Backup, reposition the caster for a more direct
approach and slowly try again.
W. CURBS & SINGL ST PS
WARNING
1. Your chair is not designed to drive up or down a curb or
step more than two and a half (2.5) inches high. Doing so
may:
• Result in a fall or tip-over.
• Damage the frame, wheels, axles or other chair parts, or
loosen fasteners.
2. To prevent a fall or tip-over, use wheelchair access ramps or
have someone help you.
3. If you must climb or descend a curb or step alone do so at
your own risk and use extreme care.
• Go as straight up or straight down as you can. Never
turn or climb or descend at an angle as a fall or tip-over
is likely.
• Proceed slowly, at a steady speed.
4. Avoid driving along curb edges and drop-offs. A minimum dis-
tance from the edge of 18” is recommended.
X. STAIRS
WARNING
Never use this chair to go up or down stairs, even with an
attendant. Doing so is likely to cause a fall or tip-over.
Y. SCALATORS
WARNING
Never take this chair on an escalator, even with an attendant.
Doing so is likely to cause a fall or tip-over.
NGLISH
10
119832 Rev. B
All manuals and user guides at all-guides.com

2. To avoid a trip or fall when you transfer:
• Make sure your feet do not “hang up” or get caught in
the space surrounding or in between the footrests.
• Avoid putting weight on the footplate or footrests, as the
chair may tip forward.
• Flip the footplate back or swing the footrests out of the
way, if possible.
3. Never lift this chair by the footplate or footrests. Footrests
fold or detach and will not bear the weight of this chair. Lift
this chair only by non-detachable parts of the main frame.
F. MOTOR LOCKS
WARNING
1. Do not engage or disengage motor locks unless power to
the chair is off.
2. Be aware that the chair will not have brakes when motor
locks are in the free-wheel position. (See Section F of
Operating Guide.)
3. Make sure that the person pushing the chair has full control
when motor locks are disengaged.
G. ON/OFF SWITCH
WARNING
1. Never use the ON/OFF switch to stop the chair except in
an emergency. This will result in an abrupt stop and may
cause you to fall.
2. To slow your chair to a stop, return the joystick to neutral,
before turning off the chair.
H. POSITIONING B LTS
WARNING
Use a positioning belt only to help support your posture.
Improper use of such belts may cause severe injury or death.
1. Make sure you are not at risk to slide down in the wheel-
chair seat. If this occurs, you may suffer chest compression
or suffocate due to pressure from the belt.
2. A pelvic wedge or a similar device can help you from sliding
down in the seat. Consult your health care professional to
find out if you need such a device.
3. The belt must be snug, but must not be so tight that it inter-
feres with breathing. You should be able to slide your open
hand, flat, between the belt and your stomach.
4. Make sure you can easily remove the belt in an emergency.
5. Never use a positioning belt:
• In place of a motor vehicle seat belt. In an accident or
sudden stop you may be thrown from the chair. A posi-
tioning belt will not prevent this, and further injury may
result from the belt.
• As a restraint. A restraint requires a doctor’s order.
• On a rider who is comatose or agitated.
I. S ATING SYST MS
WARNING
1. Use of a seating system not approved by Sunrise may alter
the center of balance of this chair. This may cause a fall or
tip-over.
2. Never change the seating system of your chair unless you
consult your supplier first.
VII. ARNINGS: COMPONENTS & OPTIONS
WARNING
If you use parts or make changes not authorized by Sunrise it
may create a safety hazard and will void the Warranty.
A. ARMR STS
WARNING
Armrests cannot be used to lift chair or the seat.
1. Never lift this chair by its armrests.
2. Lift this chair only by non-detachable parts of the main
frame.
B. BATT RI S
WARNING
1. Only deep cycle sealed case construction batteries should be
used in this device.
2. To prevent an acid spill, always keep batteries upright.
(wet cell batteries only)
3. Never smoke or hold an open flame near batteries. They are
a known explosion hazard.
4. Always wear rubber gloves and safety glasses when you han-
dle batteries.
5. Read all of section X Batteries before attempting to change
or charge batteries.
C. CUSHIONS
WARNING
1. Quickie Highback seats are designed for comfort, not specifi-
cally for the relief of pressure.
2. If you suffer from pressure sores, or if you are at risk that
they will occur, you may need a special seat system such as
can be provided by the Seat Frame, or a device to control
your posture.
• Consult your doctor, nurse or therapist to find out if you
need such a device for your well-being.
D. FAST N RS
WARNING
Many of the screws, bolts and nuts on this chair are special
high-strength fasteners. Use of improper fasteners may cause
your chair to fail.
1. Only use fasteners recommended by Sunrise.
2. If fasteners become loose, tighten them as soon as you can.
3. Over- or under-tightened fasteners may fail or cause damage
to chair parts.
• See Section VIII, “Set-Up, Adjustment & Use”, for proper
torque settings.
. FOOTPLAT & FOOTR STS
WARNING
1. At the lowest point, the foot platform and footrests should
be at least 2 1/2" off the ground. If set too LOW, it may
“hang up” on obstacles you can expect to find in normal use.
This may cause the chair to stop suddenly and tip forward.
VII. ARNINGS: COMPONENTS & OPTIONS
NGLISH
11 119832 Rev. B
All manuals and user guides at all-guides.com
all-guides.com

119832 Rev. B 12
NGLISH VII.
J. UPHOLST RY FABRIC
WARNING
1. Replace worn or torn fabric of the seat as soon as you can. If
you fail to do so, the seat may fail and cause you to fall. Worn
fabrics may increase the potential for a fire hazard.
2. Fabric will deteriorate with age and use. Look for fraying,
thin spots, or stretching of fabric at rivet holes. Replace fab-
ric as required.
3. Be aware that washing may reduce flame retardation of the
fabric.
K. SUSP NSION
WARNING
The suspension system does contain Dry Natural Rubber. The
suspension, or any other component on the chair, does not
contain any latex based product. The suspension components
are enclosed and inaccessible to the user.
L. WIRING
WARNING
Never pull on cables directly. This can result in wires breaking
inside the connector or harness. To remove a plug or connec-
tor, always grasp the plug or connector itself. (See section XI
for wiring diagram.)
M. POW R S ATING (SC only)
WARNING
1. Operation
• While driving this wheelchair in the tilted position use cau-
tion.
• Do Not attempt to operate any power seating option
while positioned on an incline.
• Do Not attempt to operate any power seating option
while this wheelchair is in motion.
• Do not attempt to operate the power seating options
around children.
2. Drive Inhibit
This power chair is designed to automatically reduce driving
speed when the power seating is tilted more than 16°.
3. Pinch points
Pinch points may occur when operating the powered seating
options on this chair. nsure all hands and body parts are
clear of all power seating components that may result in
pinch points before operating them.
4. Tilting Power Base with Push Handles
Do not attempt to tilt power wheelchairs by pulling down
on the push handles. Power wheelchairs have heavy bases. As
such, attempting to tilt a power wheelchair to traverse
obstacles can damage components in the seating system
and/or modular actuators.
5. Remain Clear During Power Accessory Operation
Please stay clear of any powered actuator while the compo-
nent is in motion. Sunrise power mechanisms move over
large ranges of travel. Users should be aware of their sur-
roundings while components are in motion.
6. Maximum User Weight
Do not exceed the weight capacity for your specific
chair/seating system configuration. Doing so could result in
premature failure or injury.
N. S.P.O.T. (Single Power Option Tilt)
POW R ACC SSORY (SC only)
WARNING
The powered S.P.O.T. accessory for this chair has a maximum
user weight capacity of up to 300 lbs. Never exceed this
capacity while operating the powered actuator.
WARNING
The powered S.P.O.T. should not be operated for more than
three minutes of continuous use. Doing so may shorten the
life of the powered S.P.O.T..
O. TRANSIT OPTION
WARNING
Contact Sunrise Medical Customer Service (800-333-4000) with
any questions about using this power wheelchair for seating in a
motor vehicle or if a Pulse 6 is a candidate for the transit option
Whenever possible, wheelchair occupants should transfer into the
vehicle seat and use the O M (Original quipment Manufacturer)
vehicle-installed restraint system.
This wheelchair has been dynamically tested in a forward-facing
mode with a specified crash test dummy restrained by both pelvic
and upper-torso belt(s) (shoulder belts). It has been determined
that both the pelvic and upper-torso belt(s) should be used to
reduce the possibility of head and chest impacts with vehicle com-
ponents. When travelling in a motor vehicle, use only Wheelchair
Tie-down and Occupant Restraint Systems (WTORS) which meet
the requirements of the SA (Society of Automotive ngineers)
J2249 Recommended Practice.
This wheelchair has been tested for seating in a motor vehicle with
the factory-installed seating system only. This wheelchair must be
in a forward facing position during travel in a motor vehicle.
This wheelchair is equipped with wheelchair-anchored pelvic belts.
It has been dynamically tested to rely on wheelchair-anchored
pelvic belts. If desired, vehicle-anchored pelvic belts may also be
used.
It is strongly recommended that the combination of both pelvic
and upper-torso belt(s) be used to reduce the risk of injury if a
sudden stop and/or collision were to occur.
To reduce the potential of injury to vehicle occupants, wheelchair-
mounted accessories, including but not limited to IV poles, trays,
respiratory equipment, backpacks, and other personal items should
be removed from the wheelchair and secured separately.
All manuals and user guides at all-guides.com

119832 Rev. B
13
NGLISH
Postural supports, positioning devices, and/or strap(s) should not
be relied on for occupant restraint. These items may be used in
addition to the wheelchair anchored, or vehicle-anchored belts.
Wheelchairs with adjustable seat angles must be set to 10°. Do not
alter or substitute wheelchair frame parts, components, or seating sys-
tems.
A sudden stop and/or collision may structurally damage your
wheelchair. Wheelchairs involved in such incidents should be
replaced.
Spill proof batteries, such as “gel cells”, should be installed on
wheelchairs to be used during travel in a motor vehicle.
WARNING
NOT : Only use the transit rackets included with Quickie Pulse 6 for
the purposes descri ed in this manual.
ABOUT TRANSPORT R ADY PACKAG S
The Quickie Pulse 6 Transit System includes four factory-installed
transport brackets and an optional wheelchair anchored pelvic
belt. The Quickie Pulse 6 has been crash-tested in accordance
with ANSI/R SNA WC Vol 1 Section 19 Frontal Impact Test
requirements for wheelchairs with a 170 lbs. crash dummy.
As of this date, the Department of Transportation has not approved
any tie-down systems for transportation of a user while in a wheel-
chair, in a moving vehicle of any type. It is Sunrise Medicals position
that users of wheelchairs should be transferred into appropriate
seating in vehicles for transportation and use be made of the
restraints made available by the auto industry. Sunrise Medical can-
not and does not recommend any wheelchair transportation sys-
tems.
COMPLIANC INFORMATION
This wheelchair conforms to the requirements of the ANSI/R SNA
WC/Vol. 1 - Section19.
NOT :ANSI = American National Standards Institute, RESNA=
Reha ilitation Engineering and Assistive Technology Society of
North America.
This wheelchair has been dynamically tested in a forward-facing mode
with a specified crash test dummy, restrained by both pelvic and
upper-torso belts in accordance with ANSI/R SNA WC Vol 1 Section
19. Both pelvic and upper-torso belts should be used to reduce the
possibility of head and chest impacts with vehicle components in the
event of a sudden stop and/or collision
S CURING TH WH LCHAIR TO TH V HICL
(See Figures 1,2 below)
WARNING
This wheelchair must be in a forward facing position during travel
in a motor vehicle. The recommended clear zones for wheelchair
seated occupants restrained by both pelvic and upper-torso belt(s)
and only by a pelvic belt are shown in the diagrams and described
below. Frontal Clear Zones (FCZ) need to be larger when upper-
torso belt(s) are not used.
The rear clear zone of 16-inches is measured from the rearmost
point on an occupant’s head.
The frontal clear zone is measured from the front most point on
an occupant’s head and is 26-inches with pelvic and upper-torso
belt(s) and 37-inches with only a pelvic belt.
The frontal clear zone may not be achievable for wheelchair-seated
drivers.
The estimated seated height (HHT) from the ground or floor to
the top of the wheelchair-seated occupant’s head ranges from
approximately 47-inches for a small adult female to about 61- inch-
es for a tall adult male.
HHT
1
VII.
2
All manuals and user guides at all-guides.com

119832 Rev. B 14
NGLISH
S CUR M NT POINTS
Rear Securement points(A), Front Securement points(B), Pelvic
Belt Securement point(C)
S CURING TH WH LCHAIR
This wheelchair is to be used only with Wheelchair Tie-down and
Occupant Restraint Systems (WTORS) that have been installed in
accordance with the manufacturer's instructions and SA J2249.
NOT : A copy of SA J2249 Wheelchair Tie-down and Occupant
Restraint Systems (WTORS) for use in Motor Vehicles can be
obtained from:
SA International,
400 Commonwealth Drive,
Warrendale, PA 15096-0001
[phone] or [phone]
Attach WTORS to the tie-down brackets in accordance with the
manufacturers instructions and SA J2249.
S CURING TH OCCUPANT
WH LCHAIR-ANCHOR D B LTS (Figure 3,4)
WARNING
Only use a pelvic belt system that meets the requirements of
ANSI/R SNA W/C 19 and SA J2249 and has been specified to
work in conjunction with the Quickie Pulse 6 Transit System.
1. Install the pelvic belt (A) onto the pelvic belt securement
point anchored to the seating frame of the Quickie Pulse 5
or 6. Using a 10mm Allen head wrench and torque to144
in-lbs securing the pelvic belt to the mounting anchor (B).
2. Repeat Step 1 for the opposite side.
V HICL -ANCHOR D B LTS (Figure 5)
This wheelchair has an overall rating of “A” with regard to accom-
modating the use and fit of vehicle-anchored belts. This rating is
scored as follows:
A = xcellent
B = Good
C = Fair
D = Poor
The test for Lateral Stability Displacement for Point (P) is shown in
the figure below. The average test result for point (P) is:
• Quickie Pulse 6 - 0.547-inches (13.9 mm).
• Quickie Pulse 5 - 0.547-inches (13.9 mm).
NOT : Figure 5 showsRear view of the wheelchair and human surro-
gate secured on test platform and tilted to 45°.
C
VII.
A
B
D
3
4
5
All manuals and user guides at all-guides.com

119832 Rev. B
15
NGLISH
S ATING SYST M
WARNING
This wheelchair has been tested for seating in a motor vehicle with the
factory installed seating system only.
nsure that the factory installed seating system is secured to the wheel-
chair frame before operation. Refer to the seating system owner’s manual
CAPTAINS S AT TRANSIT OPTION
LOCKING PIN ACTIVATION (Figure 6,7)
WARNING
Captains seat must be used in conjunction with WC-19 Tie-down brackets.
1. Configuration for Standard use (Driving the Chair)
• Locking Pin Lever (A) should be Disengaged, (Figure 6)
• Backrest can be reclined or folded as needed.
2. Transit Configuration (Captains seat used in a vehicle)
• Locking Pin Lever (B) should be engaged, (Figure 7)
• Backrest is now in locked position (99°).
MAK SUR TO NGAG LOCKING PIN FOR TRANSIT US
POSITIONING B LTS (Figure 8,9)
WARNING
The angle of the pelvic belt should be within the preferred zone of 45 to 75
degrees to the horizontal or within the optional zone of 30 to 45 degrees to
the horizontal.
Steeper side-view pelvic belt angles are especially important if the pelvic
belt is intended to be used for postural support in addition to occupant
restraint in a frontal crash. Steeper angles will reduce the tendency for a
vertical gap to develop between the user and the belt due to compliance
of seat cushions and belt movement, thereby reducing the tendency for
the user to slip under the belt and for the belt to ride up on the soft
abdomen during normal use. Steeper belt angles also reduce the tendency
for upper-torso belts to pull the pelvic belt onto the abdomen during frontal
impact loading.
NOT : For this procedure, refer to figure 9
1. The pelvic belt should be worn low across the front of the pelvis.
2. Position the upper-torso belt(s) over the shoulders.
3. The belt(s) should not be held away from the body by wheelchair
components or parts, including but not limited to wheelchair arm-
rests or wheels.
4. nsure the belt(s) are not twisted.
5. Adjust belts as firmly as possible, being mindful of user comfort.
6
7
VII.
A
B
8
9
All manuals and user guides at all-guides.com

119832 Rev. B 16
NGLISH VIII. SET-UP, ADJUSTMENT & USE
VIII. SET-UP, ADJUSTMENT & USE
NOT S:
1. Work Surface For Set-Up:
Use a flat surface, such as a table, to assemble, adjust and check your chair. This makes the
steps easier and helps ensure a correct set-up.
2. Fasteners:
• Many of the screws and bolts on this chair are special high-strength fasteners and may
have special coatings.
• Many nuts are of the Nylock type. They have a plastic insert to help prevent loosening.
WARNING
1. Use of improper fasteners may cause the chair to fail.
2. Over- or under-tightened fasteners may fail or cause damage to chair parts.
3. If bolts or screws become loose, tighten them as soon as you can. Loose bolts or
screws can cause damage to other chair parts causing them to fail.
3. Washers & Spacers:
• Note the position of washers and spacers before disassembly.
• To avoid damage to the frame, replace all washers and spacers when you reassemble
parts.
4. Torque Settings:
• A torque setting is the optimal tightening for a particular fastener. Use a torque
wrench that measures 120 inch-pounds to secure screws, nuts and bolts on this chair.
NOT – Unless otherwise noted, use a torque setting of 120 inch-pounds for all fasteners.
TOOLS YOU WILL N D
1. Basic Tool Kit:
To set-up, adjust and maintain your chair you will need the following tools:
2. Torque Wrench:
If you plan to adjust and maintain this chair yourself, Sunrise recommends that you use a
torque wrench.
NOT – The wrench must measure inch-pounds. You can buy a torque wrench and proper sockets
from a hardware store.
CH CK-OUT
Be sure this chair performs to your chosen operational settings. If it does not, turn the chair
off immediately and have your supplier reprogram your wheelchair as needed.
NOT – Repeat this procedure until the chair performs to your specifications.
WARNING
When properly set up, this chair will operate smoothly. Check to see that all compo-
nents work properly. If you detect a problem, be sure to correct it before use.
• 5mm Allen Wrench
• 6mm Allen Wrench
• 8mm Allen Wrench
• 3/8" combination wrench
• 10mm combination wrench
• 13mm combination wrench
• 18mm combination wrench
• 17mm deep socket wrench
• 19mm socket wrench
• Phillips screwdriver #2
• Flat-head screwdriver
• Wire cutters
• Needle nose pliers
All manuals and user guides at all-guides.com
all-guides.com

119832 Rev. B
17
NGLISH
13
VIII.
A. BATT RY R MOVAL (Figures 10, 11)
To remove the batteries for transporting or servicing:
1. Remove Batteries
a. Carefully remove seat (see Section O. Seat Removal).
b. Remove the shroud by first removing the six fasteners (Figure 10). Then lift up on the
shroud.
c. Unplug main power connect (A) (Figure 11).
d. Lift batteries out of the frame using the battery strap as a lifting handle
2. Battery Installation
See Section X. Batteries, D for installation.
WARNING
Batteries may weigh up to 39 lbs. Care must be taken to avoid injury when
lifting up on battery straps.
B. C NT R MOUNT HANG R ADJUSTM NT
1. Removal (Figure 12)
a. Remove the four bolts (B) and slide the footrest out.
2. Height Adjustment (Figure 13)
a. Remove the six securing bolts (C).
b. Move footplate to desired height.
c. Re-install bolts (C) through desired holes.
3. Calf Pad Adjustment (Figure 14)
a. Remove the two securing bolts (D).
b. Move calf pads to desired height.
c. Re-install bolts (D) through desired holes.
14
10
11
12
A
B
C
D
All manuals and user guides at all-guides.com

119832 Rev. B 18
NGLISH
C. SWING-AWAY FOOTR STS
1. Installation (Fig.ure15)
a. Place swing-away pivot pin ( ) into the locating hole (F) on top of the hanger mount
with the footrest facing outward from frame.
b. Rotate the footrest inward until latch plate locks (G) into place on locking bolt.
2. Removal (Figure 16)
a. To remove footrest, press quick-release lever (H).
b. Rotate footrest outward and lift
3. Height Adjustment (Figure 16)
a. Remove both bolts (I) in the hanger frame tube.
b. Reposition footrest height.
c. Re-tighten all bolts (I).
D. L VATING L GR ST (Optional)
1. Installation
To install or remove levating Legrest ( LR) see instructions for Swing-away Footrest installa-
tion.
2. Adjustment (Figure 17)
a. To raise legrest, lift to desired position. Legrest will automatically lock in place.
b. To lower legrest, while seated in chair, first lift slightly then press release lever (J)
down and lower legrest to desired position.
. FOLDING BACKR ST (optional) (Figure 18)
1. Upright Positioning
a. Lift backrest to upright position so that latch handles (K) lock into place.
b. Backrest is ready for use.
2. Folding Backrest
a. Lift and turn backrest latch handles (K) inward
or outward.
b. Fold backrest forward.
WARNING
Backrest latches must be locked into place before operating wheelchair.
VIII.
15
16
17
18
G
F
H
I
J
K
All manuals and user guides at all-guides.com

119832 Rev. B
19
NGLISH
9
2
6
7
1
4
3
5
8
Height-Adjustable Armrest Key
1. Inner Arm Post
2. Receiver
3. Release Lever, Locked Position
4. Armrest Pad
5. Transfer Bar
6. Side Panel
7. Tension Adjustment Set Screw
8. Outer Arm Post
9. Receiver Adjustment Bolts
20
F. DUAL-POST H IGHT-ADJUSTABL ARMR STS (OPTION), FIX D
H IGHT STANDARD (Figure 19)
The dual-post flip-back armrest can be used as either a flip-back armrest or a removable
armrest.
1. Installing Armrest
a. Insert front and rear posts into armrest receivers.
b. ngage levers (A and B) to secure armrest.
2. Set-up for Flip-back Operation
a. Disengage lever (A) so front post is able to come free.
b. Armrest now has the ability to be flipped back without removal.
3. Set-up for Removal
a. Disengage levers (A and B) so front and rear posts are able to come free.
b. Armrest can now be easily removed for transferring.
4. Height-Adjustment (option)
a. Release the upper securing lever (C).
b. Set at desired height
c. Return securing lever to locked position.
d. Move armrest up or down to allow armrest to snap into place
G. SINGL POST H IGHT-ADJUSTABL ARMR STS (optional) (Figure 20)
1. Installation
a. Slide the outer armpost into the receiver mounted to the wheel chair frame.
b. The armrest will automatically lock into place.
2. Height Adjustment
a. Rotate release lever to stop.
b. Slide armrest pad up or down to desired height.
c. Return lever to locked position.
d. Push arm pad until upper armpost locks firmly into place.
3. Removing Armrest
a. Rotate release lever and remove the armrest.
4. Replacing Armrest
a. Slide armrest back into receiver.
b. Return release lever to locked
position against armpost.
5. Adjusting Armrest Receiver Fit (Tighten or loosen fit)
a. Loosen the four bolts on the sides of the receiver.
b. With the armrest in the receiver, squeeze the receiver to achieve the desired fit.
c. Tighten the four bolts.
6. Adjusting Inner Armpost Fit
a. Two set screws are installed in the outer armpost.
b. Turn the set screws in or out until the desired fit is achieved.
H. ASAP S AT D PTH 14" - 16", 20" - 22" only (Figure 21)
1. Seat Frame Depth Adjustment
a. To adjust, remove the two bolts (A & B) from each side of the backrest pivot plate.
b. Reposition the backrest to the desired position.
c. Replace and retighten bolts on each side of the backrest pivot plate.
2. Back Angle Adjustment on Seat Frame
a. Remove the front securing bolt (D) on the side of the backrest hinge plate.
b. Loosen the lower rear bolt ( )
c. Set at desired angle. There are five holes (in 4º increments) to choose from.
d. Reinstall the front bolt and tighten both bolts securely.
VIII.
19
21
C
A
B
D
All manuals and user guides at all-guides.com

119832 Rev. B 20
NGLISH
QUICKIE PULSE
I. CAPTAIN’S S AT
Manual Recline/Folding Seatback adjustment
To adjust the recline angle(Figure 22,23)
1. Reclining Position
a. To adjust, pull up on the seat back release lever (A) located on the right side of the
backrest.
b. Lean forward or backwards to your desired position..
c. Release the lever (A) Wiggle the backrest to make sure it locks in place
2. To Fold Seat back (unoccupied)
a. Pull up on the seat/back release lever (A) located on the right side of the backrest.
b. Backrest should spring forward by itself into the folded position, flat against the seat
cushion.
c. Release the lever (A).
d. To unfold the back, pull up on the seat/back release lever (A) and adjust the back to an
upright position.
Seat Depth Adjustment (Figure 24)
1. Adjustment with 1” increments
a. Using a 5mm Hex Key, remove the M8 flat head screws (B) (3) on each side
b. Using a 5mm Hex Key remove the M8 Flat Head screws (C) (1) on each side
c. Using a 5mm Hex Key loosen the M8 Flat Head screws (D) (1) on each side
d. Holding the backrest on each side, slide it front or back to achieve desired position.
Seat Depth Mounting Positions(Figure 24,25 and Table)
Using the Seat Depth Mounting Positions table, and the hole number callouts
(Figure 25) use the correct hole positions to achieve depth and width.
VIII.
22
23
24
1
2
4
3
5
6
8
7
9
5
6
8
7
9
1
2
4
3
25
Table Seat Depth Mounting Positions
A
A
B
C
D
All manuals and user guides at all-guides.com