Sunstream Evolve Mini User manual

Assembly Manual
Australia - 1800 316 962 | New Zealand 0800 21 8020

Prepare & Position the Sauna Floor
If you are assembling your sauna on a hard surface
floor it is recommended that you apply the included
adhesive felt pads to the bottom of the sauna floor.
Place the sauna floor in the desired location.
It is necessary to position the floor out from your walls for assembly and move the sauna following assembly.
It is important that the sauna floor is level. Checking with a large level is recommended. If the floor is not
level, shimming or other remedies should be applied before assembling the sauna.
Australia - 1800 316 962 | New Zealand 0800 21 8020

Left Side Wall
Place the Left Side Wall on your floor behind the
sauna Floor Base.
Front Wall
Insert the Front Wall (with window) into
the channel in the sauna Floor Base
Australia - 1800 316 962 | New Zealand 0800 21 8020

Front Left Corner
Connect the Left Side Wall to the Front Wall by raising the Front Wall approx 1/2" then sliding down
to connect the 2 fasteners.
Cinch the two walls together by applying pressure on the outside of the Side Wall with the inside of
your knee.
Hold Left Side Wall DOWN while sliding Front Wall UP.
It is helpful if the second person applies pressure against the opposite edge of the Front Wall. This
will help ensure that the two walls remain in contact and the fasteners will connect.
Front Wall
NOTE: It is NOT necessary to lift the entire Front Wall. Simply slide the Front Wall upward at
the front corner of the sauna to connect to the Side Wall
Australia - 1800 316 962 | New Zealand 0800 21 8020

Fasteners
It may be be that your sauna's fasteners (Tab and Keyhole) are installed opposite to those pictured. In
such a case, the Wall which slides up will be opposite to that shown.
Guiding Rule: Always slide the Wall with the Tab fastener UP then DOWN on to the Wall with the
Keyhole fastener.
There are two sets of fasteners to join the saunas' corners together. After lowering the front wall, check to
ensure that both sets of fasteners have connected by looking at the corner inside of the sauna. It is
possible to connect one set of fasteners and miss the other. If there is an obvious gap in the corner
between the two walls the fasteners have not connected and the raising and lowering procedure will need
to be repeated.
The wall with the Tab Fastener always
slides UP then DOWN on to the wall with
the Keyhole fastener
Australia - 1800 316 962 | New Zealand 0800 21 8020

Back Left Corner
Repeat the procedure to connect
the Back Wall to the Left Side Wall
Raise the Wall will the Tab Fastener
approx 1/2" then slide down to
connect the 2 fasteners.
Cinch the two walls together by
applying pressure on the outside of
the Side Wall with the inside of your
knee.
Position Right Side Wall (with door)
Insert the Right Side Wall into the channel in
the Floor Base
Back Wall
Back Wall
Australia - 1800 316 962 | New Zealand 0800 21 8020

Back Right Corner
Connect the Back Wall to the Right Side Wall Raise the
Wall will the Tab Fastener
approx 1/2" then slide down to connect the 2 fastenersl
Cinch the two walls together by applying pressure on
the outside of the Side Wall with the inside of your knee.
Front Right Corner
Repeat the procedure to connect the Right
Side Wall to the Front Wall
Australia - 1800 316 962 | New Zealand 0800 21 8020

Connect the Front Wall heater electrical
lead to the floor base.
Ensure that the connector is fully inserted and that the
threaded cuff is fully screwed onto the Floor Base
connector.
Under-Bench Electrical
NOTE: Do not connect main power
cord to your wall outlet at this time.
Australia - 1800 316 962 | New Zealand 0800 21 8020

Connect the circular connector to
Power Supply Box.
Align the groove in connector to
properly insert. Thread the cuff of
the connector on fully.
Attach the 'D-Sub' computer
style connector as shown.
Plug in all heater leads to the
receptacles in the Power Supply Box.
Feed the main Power Supply Cord in through the hole in the Back Wall and
insert in Power Supply Box.
Do NOT plug Power Cord into your wall outlet until all electrical connections are finished inside of the sauna
and for the Roof.
Australia - 1800 316 962 | New Zealand 0800 21 8020

Remove Side Wall
Heater Guards
The wooden lattice work in front of the heaters
is referred to as the heater guard. These are
held in place with strong magnets.
It is necessary to remove the heater guards from
the two side walls in order to install the leg heater
and the sauna bench.
Leg Heater
Install the Leg Heater by lowering it into the holding
brackets mounted on the side walls.
Plug the Leg Heater into the power supply box in floor.
Australia - 1800 316 962 | New Zealand 0800 21 8020

Install the Sauna Bench
Reinstall the Side Wall
Heater Guards
Australia - 1800 316 962 | New Zealand 0800 21 8020

Install Sauna Roof
Lower the Roof into place by first fitting the Door
side of Roof on the sauna Walls
Keep the opposite side of Roof elevated to enable
connection of the 12 V power supply line.
Ensure that 12V DC power line from the Roof
(with white plastic connector) is accessible before
installing the Roof.
If you are unable to grab hold of the 12V power line from inside the
roof it may be necessary to remove the first T&G board on the Roof
(access panel) and feed the wire down through the hole in the roof.
Australia - 1800 316 962 | New Zealand 0800 21 8020

Connect the 12 V power line between the
Side Wall and Roof.
Tuck the white plastic connector inside of
the Roof and lower the Roof into place.
It may be necessary to gently push on the
inside or outside of the walls to align tops of
walls with the Roof channel.
Reinstall the roof access panel if necessary
Note: Please see 'Audio System' section
regarding the Roof access panel.
Install the Door Handle
Australia - 1800 316 962 | New Zealand 0800 21 8020

Heater Guards
The heater guards in your new Sun Stream Infrared Sauna are held to the wall with
strong earth magnets. If preferred, the heater guards can be screwed directly to the wall
for a more permanent and secure attachment. The heater guards are pre-drilled for the
attachment screws.
Screws are included to attach the heater guard to the wall. Select a drill
bit with a smaller diameter than the screw threads to drill a pilot hole
Australia - 1800 316 962 | New Zealand 0800 21 8020

Drill a pilot hole into the wall through
the holes in the heater guards.Do not
drill deeper than necessary for the
length of the screw.
NOTE: The pilot holes are important
to ensure that the tongue and groove
wall boards do not split when
installing screws.
Install screws to firmly
attach heater guard to the wall
Australia - 1800 316 962 | New Zealand 0800 21 8020

Audio System
Music can be piped to the speakers in the sauna two different ways, either wireless via
the Bluetooth receiver or by directly connecting your device (smart phone, tablet, laptop
etc.) with a 3.5mm male to male audio cord.
1. Bluetooth Mode.
When you first plug the sauna into the wall outlet a beep will sound indicating the
Audio circuit board in the roof has power. The circuit board's colored LED indicator
lights will flash and these will continue to flash whenever the sauna is plugged into the
wall outlet.
To transmit audio to the sauna's speakers from your device, search for and connect
your device to the 'BT Speaker'
The Audio Circuit Board is shown inside the sauna roof
in Bluetooth Mode without an audio cord connected.
Australia - 1800 316 962 | New Zealand 0800 21 8020

2. Direct Connect Mode
(NO Bluetooth)
First, remove the access panels from
the roof by unscrewing wood screws.
Connect your device to the sauna's audio
system by inserting a 3.5 mm male to
male audio cord into the BT circuit board
as shown (Audio cords not included).
To completely eliminate the RF Bluetooth
signal, simply remove the Bluetooth
module from the circuit board as shown
Australia - 1800 316 962 | New Zealand 0800 21 8020

Reinstall the roof panels and feed your audio
cord through the hole in roof.
Enjoy your favorite audio while
relaxing in your new sauna!
Australia - 1800 316 962 | New Zealand 0800 21 8020

Control Panel
Australia - 1800 316 962 | New Zealand 0800 21 8020

Interior Control Panel
Temperature Sensor
FRAGILE
DO NOT TOUCH
Australia - 1800 316 962 | New Zealand 0800 21 8020