SuperATV PR-P-RAN-09 User manual

© 2011 SuperATV.com. All Rights Reserved. Rev IN-PR-P-RAN-09 3/3/2014
Polaris Ranger Plastic Roof
INSTALLATION INSTRUCTIONS
740B Clifty Drive • Madison, Indiana 47250 • 812-574-7777
Liability Statement
SuperATV’s products are designed to best t users ATV/UTV under stock conditions.
Adding, modifying, or fabricating any factory, or aftermarket, parts will void any
warranty provided by SuperATV and is not recommended. SuperATV’s products
could interfere with other aftermarket accessories. If user has aftermarket products
on machine, contact SuperATV to verify that they will work together.
Although SuperATV has thousands of satised customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc will change the ride
of machine and may increase maintenance and part wear. Operating any off-road
machine while, or after, consuming alcohol and/or drugs increases risk of bodily
harm or death. No warranty or representation is made as to this product’s ability to
protect user from severe injury or death. SuperATV urges operators and occupants
to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV products, user agrees that should damages
occur, SuperATV will not be held responsible for loss of time, use, labor fees,
replacement parts, or freight charges. SuperATV, nor any 3rd party, will not be held
responsible for any direct, indirect, incidental, special, or consequential damages
that result from any product purchased from SuperATV. The total liability of seller to
user for all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the product that gave rise to the claim.
SuperATV will warranty only parts provided by SuperATV. Any damage or problems
with OEM housings, bearings, seals, or other manufacturers products will not be
covered by SuperATV. SuperATV parts and products are not warrantied if item was
not installed properly, misused, or modied.
Read instructions and view illustrations before beginning.
Need help with your installation?
1-812-574-7777
[e-mail] www.superatv.com
8:00am - 9:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
Thank You
For Choosing
If installing on Bobcat 3400, modications are required.
M6-1.0 x 20mm Lg. PHMSQty (10) M6-1.0 Nylock NutQty (10)
M6 Fender WasherQty (6) Qty (6) M6 Flat Washer
AB
Item Description Qty
ARoof Half (Passenger) 1
BRoof Half (Driver) 1
CTube Clamps 8 C

2
Do not tighten hardware completely unless noted.
1. Place Roof Half (B) on top of machine followed by Roof Half (A).
2. Place Tube Clamps (C) around Roll Bar. Attach Roof (A)(B) to Tube Clamps (C) using (6) each
M6-1.0 x 20mm Lg. PHMS, M6 Fender Washers, and M6-1.0 Nylock Nuts. See Figs. 1 - 1b. Note:
Center holes do not use Fender Washers.
3. Tighten hardware completely.
4. Secure Roof Halfs (A)(B) together with (2) each M6-1.0 x 20mm Lg. PHMS, M6 Flat Washers, and
M6-1.0 Nylock Nuts.
5. Drill (2) Ø1/4” holes through Roof Halfs (A)(B) and join together with (1) M6-1.0 x 20mm Lg. PHMS
(D), (2) M6 Flat Washers, and (1) M6-1.0 Nylock Nut for each hole. See Fig. 2.
Fig. 1b
A
B
AB
holes to be in-line
B
A
Fig. 1a
Rear
Driver Side
M6 Nylock Nut
C
M6 x 20mm Lg. PHMS
Fig. 1
B
Roll Bar
C
Front
Driver Side
M6 Fender Washer
M6 Flat Washer
M6 Nylock Nut
M6 x 20mm Lg. PHMS
If installing on Bobcat 3400 models, proceed to page 3.
(illustrations continue on following page)

3
A
(Passenger Side)
Fig. 1a
(Driver Side) Fig. 1
B
If installing on Bobcat 3400 models, forward mounting locations will require modication. See below.
1. Measure over, approximately 2” towards center of machine, from original mounting hole. Original front
mounting locations will not work; Tube Clamps (C) will interfere with Roll Bar.
2. Mark and drill new mounting hole. Repeat for opposite side.
Return to Page 2, Step 2 to complete installation.
Roll Bar
Roll Bar
Original mounting hole
measure towards
machine center measure towards
machine center
Original mounting hole
Fig. 2
B
A
Drill and secure
M6 x 20mm Lg. PHMS M6 Flat Washers
M6 Nylock Nut
Bobcat 3400