SUTO S030 Manual

English
Instruction and Operation Manual
S030
Electrical Current Transmitter

Dear Customer,
Thank you for choosing our product.
The operating instructions must be read in full and carefully observed
before you start up the device. The manufacturer cannot be held liable
for any damage which occurs as a result of non-observance or non-
compliance with this manual.
Should the device be tampered with in any manner other than a
procedure which is described and specified in the manual, the warranty
is cancelled and the manufacturer is e empt from liability.
The device is destined e clusively for the described application.
SUTO offers no guarantee for the suitability for any other purpose.
SUTO is also not liable for consequential damage resulting from the
delivery, capability or use of this device.
2S030

Table of contents
1 Safety Instructions......................................................................4
2 Registered Trademarks................................................................5
3 Application.................................................................................6
4 Features....................................................................................6
5 Technical Data............................................................................7
5.1 General................................................................................7
5.2 Electrical Data.......................................................................7
5.3 Output Signals......................................................................7
5.4 Accuracy .............................................................................7
6 Installation ................................................................................8
6.1 Installation...........................................................................8
6.2 Electrical Connection..............................................................9
7 Signal Outputs............................................................................9
8 Maintenance...............................................................................9
9 Disposal or Waste......................................................................10
S030 3

1 Safety Instructions
1 Safety Instructions
Please check if this instruction manual accords to the
product type
Please observe all notes and instructions indicated in this
manual. It contains essential information which have to be
observed before and during installation, operation and
maintenance. Therefore this instruction manual has to be read carefully
by the technician as well as by the responsible user / qualified
personnel.
This instruction manual has to be available at the operation site of the
device at any time. In case of any obscurities or questions, regarding
this manual or the product, please contact the manufacturer.
WARNING!
Voltage used for supply!
Any contact with energized parts of the product, may
lead to an electrical shock which can lead to serious
injuries or even death!
•Consider all regulations for electrical installations.
•The system must be disconnected from any power supply during
maintenance work.
•Any electrical work on the system is only allowed by authorized
qualified personal.
WARNING!
Permitted operating parameters!
Observe the permitted operating parameters, any
operation exceeding this parameters can lead to
malfunctions and may lead to damage on the
instrument or the system
•Do not e ceed the permitted operating parameters.
•Make sure the product is operated in its permitted limitations.
•Do not e ceed or undercut the permitted storage and operation
temperature.
4S030

1 Safety Instructions
General safety instructions
•It is not allowed to use the product in e plosive areas.
•Please observe the national regulations before/during installation
and operation.
Remarks
•It is not allowed to disassemble the product.
ATTENTION!
Measurement values can be affected by malfunction!
The product must be installed properly, otherwise it
may lead to wrong measurement values, which can
lead to wrong results
Storage and transportation
•Make sure that the transportation temperature of the device is
between -30°C ... 80°C.
•For transportation it is recommended to use the packaging which
comes with the device.
•Please make sure that the storage temperature of the device is
between -40°C ... 80°C.
•Avoid direct UV and solar radiation during storage.
•For the storage the humidity has to be <90%, no condensation.
2 Registered Trademarks
SUTO® Registered trademark of SUTO iTEC
MODBUS®Registered trademark of the Modbus Organization,
Hopkinton, USA
HART® Registered trademark of the HART Communication
Foundation, Austin, USA
S030 5

3 Application
3 Application
The S030 Electrical Current Transmitter is designed to measure the
current carried on a power conductor within the permissible operating
parameters. These parameters can be found in the technical data
section.
The S030 Electrical Current Transmitter is not developed to be used in
e plosive areas. For the use in e plosive areas please contact the
manufacturer.
4 Features
•Easy installation
•Wide measuring range
•Accurate current sensing
•4 mA ... 20 mA output signal
•IP67 casing provides robust protection in the industrial
environment
6S030

5 Technical Data
5 Technical Data
5 1 General
Measuring range 10 A ... 1000 A (AC) 30 A ... 3000 A (AC)
S554 0156
S554 0155
S554 0157
S554 0158
Fundamental frequency 40 Hz ... 70 Hz
Operating temperature -30 ... 80 °C
Protection class IP67 (Clamp sensor)
IP20 (Electronics)
Clamp diameter 100 mm 150 mm
Weight 250g
5 2 Electrical Data
Power supply 21 VDC ... 27 VDC
5 3 Output Signals
Analogue output 4 ... 20 mA DC equal to 0 ... ma . AC current
Output ripple factor 5%
5 4 Accuracy
Accuracy 0.5% of reading
0.25% of range
S030 7

6 Installation
6 Installation
Please make sure that all components listed below are included in your
package.
Qty Description Item no
1 S030 Electrical Current Transmitter S554 0155 / S554 0156
S554 0157 / S554 0158
1 Instruction manual No P/N
ATTENTION!
Wrong measurement is possible if the transmitter is
not installed correctly
The S030 is for indoor use only! At an outdoor installation, the
transmitter must be protected from solar radiation and rain.
6 1 Installation
The following steps e plain the procedure of an appropriate installation.
1. Fit the coil around the isolated conductor in a way that the
conductor remains in the center of the coil ring.
2. Bring the coil ends together and lock it with the screw ring.
8S030

6 Installation
6 2 Electrical Connection
There are two different types of the S030 Electrical Current Transmitter:
•Model S554 0155 / S554 0158 with open wire end. See the table
below for the electrical connection:
Wire colour Signal
Red + VB （24 VDC)
Blue - VB
Green Signal GND
Yellow 4 mA ... 20 mA Signal
•Model S554 0156 / S554 0157come with connector to S551. For
the electrical connection please use the ports 3 or 4 of the S551.
7 Signal Outputs
The S030 Electrical Current Transmitter has an analog output range of 4
mA ... 20 mA. This output is scaled to:
•4 mA = 0 A
•20 mA = 1000 / 3000 A
8 Maintenance
•Keep the transmitter clean and free of surface contamination.
•Clean the transmitter with a soft cloth damp with a water and
neutral soap only.
•Make sure the product is dry before use.
•Do not use or leave the product in particularly dirty or dusty
environment.
ATTENTION!
Do not use corrosive chemical products, solvents or
aggressive detergents to clean the transmitter
S030 9

9 Disposal or Waste
9 Disposal or Waste
Electronic devices are recyclable material and do not
belong in the household waste.
The transmitter, accessories and its packings must be
disposed according to your local statutory requirements.
The dispose can also be carried by the manufacturer of the
product. For more information, please contact the
manufacturer.
10 S030

S030 11

SUTO iTEC GmbH
Grißheimer Weg 21
D-79423 Heitersheim
Germany
SUTO iTEC (ASIA) Co., Ltd.
Room 10, 6/F, Block B, Cambridge Plaza
188 San Wan Road, Sheung Shui, N.T.
Hong Kong
Tel: [phone]
Email: [email protected]
Website: www.suto-itec.com
Tel: [phone]
Email: [email protected]
Website: www.suto-itec.com
SUTO iTEC Inc.
5460 33rd St SE
Grand Rapids, MI 49512
USA
Tel: [phone]
Email: [email protected]
Website: www.suto-itec.com
All rights reserved © Modifications and errors reserved
S030_im_en_2023-1
12 S030