Sven MS-2085 User manual

www.sven.fi
2.1 Multimedia Speaker System
mS-2085
OPERATION
MANUAL

2.1 Multimedia Speaker System
ENG
2
Congratulations on your purchase of the Sven speaker system!
COPYRIGHT
© 2020. SVEN PTE. LTD. Version 1.0 (V 1.0).
This Manual and information contained in it are copyrighted. All rights reserved.
TRADEMARKS
All trademarks are the property of their legal holders.
NOTICE OF RESPONSIBILITY RESTRICTION
Despite the exerted efforts to make this Manual more exact, some discrepancies may occur. The
information in this Manual is given on “as is” terms. The author and the publisher do not bear any
liability to a person or an organization for loss or damage which has arisen from the information
contained in this Manual.
CONTENTS
1. BUYER RECOMMENDATIONS .............................................................................................. 2
2. PACKAGE CONTENTS............................................................................................................ 3
3. SAFETY PRECAUTIONS ......................................................................................................... 3
4. TECHNICAL DESCRIPTION ................................................................................................... 3
5. PREPARATION AND OPERATION ......................................................................................... 5
6. OPERATION MODES.............................................................................................................. 6
7. TROUBLESHOOTING............................................................................................................. 8
8. TECHNICAL SPECIFICATIONS ............................................................................................... 8
1. BUYER RECOMMENDATIONS
•Unpack the device carefully. Make sure there are no accessories left in the box. Check up the
device for damage; if the product was damaged during transportation, address the firm which
carried out the delivery; if the product functions incorrectly, address the dealer at once.
•Check up the package contents and availability of the warranty card. Make sure the warranty card
has a shop stamp, a legible signature or the seller’s stamp and purchase date, and the goods
number corresponds to that in the warranty card. Remember: in case of warranty card loss or
discrepancy of numbers you forfeit the right for warranty repairs.
•Do not switch on the speaker system immediately after you bring it into a room from environment
with negative temperature! After unpacking, the speaker system should be kept in conditions of
room temperature for at least 4 hours.
• Before installing and using the speaker system, read this Manual carefully and keep it for future
reference.
• Shipping and transportation equipment is permitted only in the original container.
• Does not require special conditions for realization.
• Dispose of in accordance with regulations for the disposal of household and computer
equipment.
Technical support is on www.sven.fi.

ENG
Operation Manual MS-2085
3
2. PACKAGE CONTENTS
• Subwoofer – 1 pc
• Satellites – 2 pcs
• Remote control – 1 pc
• AAA type batteries – 2 pcs
• 2RCA to mini-jack signal cable – 1 pc
• Antenna wire – 1 pc
• Operation manual – 1 pc
• Warranty card – 1 pc
3. SAFETY PRECAUTIONS
Caution! High voltage inside! To avoid the risk of electric shock
do not open or touch elements inside.
• To avoid electric shock, do not open the MSS and do not perform repairs by yourself. Service and
repairs should be performed only by qualified specialists in an authorized service center. The list
of authorized service centers is available on www.sven.fi.
• Do not allow the circuit of wires (including the grounded ones) between the speakers, on the
power amplifier or the ground, for it causes damage to the power amplifier output stage.
• Do not touch the MSS power cord plug pins for 2 seconds after unplugging it from the mains.
• Do not put foreign objects inside the holes of the MSS.
• Protect the MSS from high humidity, water and dust.
• Protect the MSS from heating: do not place it closer than 1 m from a heat source. Do not expose
it to direct sunlight.
• Do not place any open flame sources on or close to MSS.
• Do not place the MSS in poorly ventilated areas. Leave an air gap of 10 cm or more. When
operating the MSS, do not put any devices on it, do not cover it with cloth or other objects
preventing it from cooling.
• Do not use any chemical agents for cleaning. Clean it with dry soft cloth only.
4. TECHNICAL DESCRIPTION
MS-2085 2.1 Multimedia Speaker System (MSS) is designed to play music and sound games, movies,
etc. The MSS has a built-in power amplifier and audio cables allowing to connect it to virtually any
audio source (CD/DVD-player, TV, PC, etc.) without using an additional power amplifier. The MSS
has a built-in FM radio, Bluetooth-module and audio player. Remote control is included.
Special features
• Wireless signal transmission via Bluetooth
• Switchable backlight
• Built-in audio files player from USB-flash and SD card storage devices
• Built-in FM radio
• LED display
• Remote Control
• Wooden (MDF) cabinets of the subwoofer and satellites

2.1 Multimedia Speaker System
ENG
4
Subwoofer control panels
aMODE: input switch PC/AUX/FM/ /Player/Bluetooth
(pressed short);
ST-BY mode (pressed long);
Turning on / off the backlight (double click)
b/VOL-: Previous track (pressed long in the Player and
Bluetooth mode);
Volume decrease (pressed short);
Previous station* (pressed long in the Radio mode)
cLED display
d: Play/Pause (pressed short in the Player and
Bluetooth mode);
Start/stop auto scan (pressed long in the Tuner mode)
e/VOL+: Next track (pressed long in the Player and
Bluetooth mode);
Volume increase (pressed short);
Next station* (pressed long in the Radio mode)
fLED1: backlight jacks
gLED2: backlight jacks
hON/OFF: power switch
iPower cord
jBASS: subwoofer volume control
kFM ANT: radio antenna input jack
lAUDIO OUTPUT: satellite output jacks
mSD/MMC CARD: slot for SD/MMC cards** containing
МР3 audio files
n USB: slot for a USB flash device** containing МР3
audio files
Fig. 1. Control panel
Fig. 2. Subwoofer rear panel
Fig. 3. Subwoofer
side panel
Remote control (Fig. 4)
aSTBY: power switch button (ST-BY mode)
bMUTE: sound on/of
cSAVE: SAVE: memorize selected frequency (short pressing
in Radio mode)
dRESET: return to default settings
eDEL: deleting a memorized station
fAUX : AUX input selection button
gFM/BT: FM/Bluetooth input selection button
hUSB: USB input selection button (Player mode)
iSD: SD input selection button (Player mode)
jRANDOM: repeat mode selection button (in the
Player mode): play tracks in the random order
* The feature is available if stations have been present in the memory.
** The storage device must be formatted as FAT, FAT32. Memory cards
SDHC class 10 or less can be used. Connection of external hard disks
other than USB flash drive is not recommended, otherwise it can cause
the MSS damage.

ENG
Operation Manual MS-2085
5
lTUN +/-: manual band scanning (in the Radio mode)
mVOL+/-: volume level control
n, : Previous/Next track (in the Player and Bluetooth
mode); previous/next station (in the Radio mode);
ON/OFF backlight (pressed long)
o, AUTO: Play/Pause (in the Player and Bluetooth mode);
start/stop auto scan (pressed long in the Radio mode)
p0-9: numeric pad (select track number in the Player mode
or track number FM Radio)
Battery Installation
• Open the battery compartment on the back of the remote
control.
• Insert the included AAA batteries.
• Close the battery compartment.
Notes:
• Use the RC at an angle no more than 30° at a distance of no
more than 7 meters.
• Direct the remote control at the LED display on the
subwoofer.
• If the remote control does not work, check the batteries or
replace the discharged batteries with new ones.
• Remove the batteries from the RC if you don’t intend to use
it for a long time.
5. PREPARATION AND OPERATION
Speaker placement
• Place the speakers symmetrically to the listener at least one
meter away. The subwoofer emits non-directional sound,
therefore it can be located in any place of the room where it
sounds the best.
• Place MSS far away from monitors and TV sets, as insignificant
image distortion in these supersensitive devices is possible.
Fig. 4. Remote
control
Installation and operation
MS-2085 speaker system can be connected to virtually any audio devices: МР3 player, PCs, laptops,
etc. (see connection diagram in Fig. 5).
• Before making any connections, make sure the MSS is off and unplugged. Connect the right
speaker to the subwoofer AUDIO OUTPUT R with the built-in audio cable and the left speaker – to
the AUDIO OUTPUT L.
• To use satellites backlight, connect the built-in cable of each satellite to the connectors LED1f/
LED2 g.
• To connect the MSS to a PC, МР3 player, use a 2RCA to mini-jack signal cable (included). Insert the
RCA jacks of the signal cable into the L and R jacks of the PC AUDIO INPUT l, and the mini-jack of
the signal cable – into the LINE OUT port of your PC sound card or an audio output of your МР3
player, as shown in Fig. 5.
kREPEAT: repeat mode selection button (in the Player mode):
ONE – repeats the current track;
ALL – plays all tracks in the sequential order

2.1 Multimedia Speaker System
ENG
6
• Connect subwoofer to the mains outlet with the power cord c.
• Turn on MSS power supply using the ON/OFF switch (k, ON) on the subwoofer rear panel.
• Turn on MSS with button aon the front panel or button aon the remote control.
• Select a signal source using the MODE abutton on the control panel or buttons f, g, h, i
on the remote control.
• Adjust master volume level with buttons band eon the control panel or with VOL+/- mbutton
on the remote control.
• Adjust subwoofer volume level using knob gon the subwoofer rear panel.
•To listen the radio, connect antenna to the FM ANT kjack (see Fig. 5) and adjust it for better
reception.
•After using MSS, mind to switch it off using the ON/OFF switch (h, OFF position) and unplug the
power cord ifrom the socket.
6. OPERATION MODES
Player Mode
• The system will automatically enter the Player mode when a USB device is connected to the USB
port mor SD card* is inserted into the corresponding slot n; or press the MODE abutton on
the front panel or use buttons h, ion the remote control. Display cwill show selected mode.
Files will automatically start playing.
• To select the track, you can enter its number on the remote control using the numeric pad
buttons por select it using buttons band e(pressed long) on the front panel.
Bluetooth mode
• In order to transmit signal in this mode it is necessary to connect device with a signal source (see
Fig. 5). For this purpose select the Bluetooth mode using button MODE aon the front panel of the
subwoofer or button FM/BT g on the remote control. After 2-3 seconds the speaker system will
enter the search mode, «BLUE» indicator is shown on the display c.
• It is necessary to select the search mode of devices with Bluetooth on a signal source (telephone,
notebook, smartphone, etc.). «MS-2085», message will be displayed on the screen which it should
be connected with**.
• The «BLUE» indicator lights continuously when connection is successful. If there is no any
connection, the lighting of the «BLUE» indicator is intermittent. In this case the system should be
switch over to the search mode once again (to turn off and turn on anew)***.
• It is possible to control the player of a signal source from the remote control or using the button
on the front panel of the subwoofer when connecting to a signal source.
Radio Mode
• To switch to the Radio mode, use the MODE abutton on the front panel or button FM/BT g
on the remote control.
* The MSS operation may be incorrect if an SD card of 512 Mb capacity or lower is used. If a USB
flash device of 8 Gb capacity or more is used, command processing time may be extended.
** You might have to enter «0000» code to connect some models of devices via Bluetooth.
*** If an item has been already registered in the device list of a source, then the second search
mode activation is not obligatory. Choose only the item name and the «connect» command on
the source.

ENG
Operation Manual MS-2085
7
• To auto scan and memorize the found stations, press button don the front panel or the AUTO
obutton on the remote control long. To stop auto scanning, press this button again before the
scanning is over. The display cwill show the frequency being scanned. When the channel is being
memorized, the display shows its number for a short moment.
• For manual scanning, use buttons TUN -/+ lon the remote control (up/down the frequency
range). To save the selected station, press SAVE cbutton on the remote control and then buttons
non the remote control, assign the station its number and press SAVE button again.
• If preset stations are available in the memory, you can switch from one to another by long
pressing buttons b, eon the front panel or buttons non the remote control. You can also enter
the frequency or the number of the preset station with the remote control numeric pad buttons
p. The display cwill show the station number for a short moment and then its frequency. The
radio will tune to the set frequency within 2-3 seconds.
AUX Mode
• To switch to the AUX mode, press the MODE abutton on the front panel or button fon the
remote control, the MSS switched on. The display cwill show AUX.
ST-BY Mode
• To enter/exit this mode, press and hold button aon the front panel or button aon the RC.
MUTE Mode
• To enter the MUTE mode, press button bon the remote control. To exit the MUTE mode, press
button bagain.
Note. Due to the constant development of the software, the actual MSS operation may differ
from that described in this Manual. The most recent version of the Manual is available at
www.sven.fi.
Fig. 5. Audio sources connection diagram
PC
Mobile device
2RCA to mini-jack
signal cable
Power
cord
Antenna

2.1 Multimedia Speaker System
ENG
8
8. TECHNICAL SPECIFICATIONS
Parameter, measurement unit Value
Output power (RMS), W:
subwoofer
satellites
60 (30 + 2 × 15)
30
2 × 15
Frequency response, Hz:
subwoofer
satellites
45–150
150–20000
Speaker diameter, mm:
subwoofer
satellites
Ø 145
Ø 70
Power supply, V/Hz ~230/50
Rated current consumption, A 0.07
Dimensions, mm:
subwoofer
satellites (one speаker)
260 × 262 × 300
106 × 182 × 122
Weight, kg 5.15
Notes:
• Technical specifications given in this table are supplemental information and cannot give
occasion to claims.
• Technical specifications and package contents are subject to change without notice due to the
improvement of SVEN production.
7. TROUBLESHOOTING
Problem Cause Solution
The MSS does not
turn on.
The MSS isn’t connected to a
mains outlet. Check the connection.
The power switch is off. Turn on the switch.
No sound or the
sound is too quiet.
Volume level is set at mini-
mum value. Adjust the volume control knob.
Improperly connected audio
source.
Connect the audio sources
correctly.
Distortion of sound. Large amplitude of the input
signal.
Turn down the source volume
and the MSS volume.
The remote control
is not working. The batteries are discharged. Replace the batteries with new
ones.
If none of the above methods can solve the problem, please seek professional advice at your nearest
service center. Never attempt to repair the product yourself.

2.1 Multimedia Speaker System
MS-2085
Model: MS-2085
Импортер в России: OOO «РЕГАРД», 105082, РФ,
г. Москва, ул. Фридриха Энгельса, д.75, стр. 5.
Уполномоченная организация в России: ООО «РТ-Ф»,
105082, г. Москва, ул. Фридриха Энгельса, д. 75, стр. 5.
Условия гарантийного обслуживания смотрите в
гарантийном талоне или на сайте www.sven.fi.
Гарантийный срок: 12 мес.
Срок службы: 5 лет.
Производитель: «СВЕН ПТЕ. Лимитед», 176 Джу Чиат
Роуд, № 02-02, Сингапур, 427447. Произведено под
контролем «Свен Скандинавия Лимитед», 48310,
Финляндия, Котка, Котолахдентие, 15. Сделано в Китае.
Manufacturer: SVEN PTE. LTD, 176 Joo Chiat Road, № 02-
02, Singapore, 427447. Produced under the control of Oy
Sven Scandinavia Ltd. 15, Kotolahdentie, Kotka, Finland,
48310. Made in China.
® Registered Trademark of Oy SVEN
Scandinavia Ltd. Finland.