Swegon PELICAN Ceiling HF Guide

Accessories
Commissioning box:
ALS. The commissioning box is made of galvanized sheet steel
and contains a removable commissioning damper, fixed measu-
rement tapping and sound absorbing material*) with reinforced
surface layer.
*) Fire resistance rated to B-s1,d0 in accordance with EN ISO 11925-2.
Frame:
SAR K, for aesthetic installation of a lowered diffuser section.
Adapter:
ADAPTER, for adaptation to various variants and makes of sys-
temized false ceilings: Ecophon, Gyproc, Dampa, etc. Used also
for adaptation to alternative sizes of systemized false ceilings,
e.g. 625 x 625 or 675 x 675. Specification available in separate
product sheet for ADAPTER.
Installation
To dismantle the front face, insert a thin object, for example a
Quick Access card or the equivalent, in between the diffuser
face and the diffuser backing box in order to release the springs.
Move the card from the centre out towards the corner, see
Figure 2.
The inlet spigot of the air diffuser backing box can be secured to
the connecting duct by means of self-tapping screws or a blind
rivets. For flush-mounting in fixed ceiling constructions, secure
the air diffuser by means of screws into place in the framework
through either the sides or top of the air diffuser backing box.
For mounting in modular suspended ceilings, it is advisable to
select air diffusers with outer dimensions of 595 x 595 mm.
Position these directly down in the T-bar framework, and then
secure them to the duct system or to the commissioning box.
If an ALS commissioning box is used, it must be secured to the
building structure by means of hangers or mounting brackets.
The distance between the commissioning box and the air dif-
fuser can be increased by as much as 500 mm without having
to lengthen the measuring tubes and damper adjustment cords.
See Figure 3.
Commissioning
Commissioning should be carried out with the front face mounted.
Pull the measuring tubes and damper adjustment cords out
through the front face. Then connect the manometer to the cor-
rect measuring tube. Always use the transparent tube for extract
air.
The rated coefficient of performance of the air diffuser can be
used in a calculation to determine the required commissioning
pressure. Conclude commissioning by adjusting the damper to the
correct blade position, tie a commissioning knot in the damper
cords to indicate the damper position.
Figure 1. Commissioning.
Quick
Access
PELICAN HF
Tomelilla
Sweden
XX0-600
+ALS XXX -XXX/XXX -XXX
k
q
K = XX / XX
p
kpq⋅=
k
pq
=
( )2
q= flow reading l/s
p= current pressure reading (Pa)
k= commissioning factor
k-factor
Measurement accuracy and requirement on straight duct before
the commisioning box, see Figure 3. The requirements of straigh
duct depends on the type of disturbance before the commis-
sioning box. Figure 3 shows a bend, a dimensional change and
a T-piece. Other types of disturbances requires at least 2xD
straight (D = connection dimension) for measurement accuracy
of ± 10% of the flow.
The rated coefficient of performance (K-factor) is specified on
the identification label of the product and in the relevant com-
missioning instructions at www.swegon.com.
Maintenance
The air diffuser can be cleaned, if necessary, using lukewarm
water with dishwashing detergent added or by vacuum clean-
ing using a brush nozzle. The duct system can be reached for
cleaning after opening the front face. If a type ALS commission-
ing box is used, swing the front face to the side on its hinges so
that you then can grip the handle of the tubular damper casing
and rotate it out of its holder. See Figure 4.
PELICAN Ceiling HF
Installation – Commissioning – Maintenance 20150615

Figure 2. Quick Access.
Figure 3. Installation alternatives.
Figure 4. To dismantle the damper.
0xD / ±5% 0xD / ±5% 2xD / ±10%
PELICAN Ceiling HF
2Swegon reserves the right to alter specifications. 20150615

K-factor
ALS PELICAN CE HF Extract air
Size Size K-factor Tube colour
125-160 160-600 8.1 Transparent
160-200 200-600 13.3 Transparent
160-250 250-500 14,7 Transparent
200-250 250-500 20,8 Transparent
200-250 250-600 20.5 Transparent
200-315 315-500 22,8 Transparent
250 -315 315-500 32,5 Transparent
250 -315 315-600 32.1 Transparent
315-400 400-600 49.6 Transparent
Number of measuring tubes: 1
J
ØD
Ød1
Figure 5. PELICAN Ceiling HF
Figure 6. PELICAN Ceiling HF with ALS. CL = Centerline.
N
Figure 7. SAR K frame.
Dimensions and weights
PELICAN Ceiling HF
Size Dimensions (mm) Weight
(kg)
AØd l M
160-600 595 159 575 70 3.5
200-600 595 199 575 70 3.5
250-500 495 249 475 70 3,4
250-600 595 249 575 70 3.5
315-500 495 314 475 70 3,4
315-600 595 314 575 50 3.5
400-600 595 399 575 50 3.5
Dimensions of opening in ceiling = l x l
CL = Center line
PELICAN Ceiling HF + ALS – One step
Size Dimensions (mm) Weight (kg)
ABCØD Ød1 E F G H J K
160-600 595 342 252 124 160 279 113 188 315 40 80 6.2
200-600 595 404 288 159 200 314 113 205 375 40 100 7.0
250-500 495 504 332 199 250 354 113 225 465 40 115 8,2
250-600 595 504 332 199 250 354 113 225 465 40 115 8.7
315-500 495 622 388 249 315 395 93 230 575 40 140 11, 8
315-600 595 622 388 249 315 395 93 230 575 40 140 11.8
400-600 595 767 488 314 400 455 93 262 712 40 175 15.0
SAR K – Frame
Size Dimensions (mm) Weight (kg)
L N
500 495 75 1
600 595 75 1
When installing size 315-600 and 400-600 air diffusers, position the ALS box
so that its branch extends 20 mm below the ceiling surface.
3
20150615 Swegon reserves the right to alter specifications.
PELICAN Ceiling HF