SYMA X110W User manual

User manual
FOLDABLE DRONE
X110W
8

DE
Contents
1-21
EN ENGLISHINTRODUCE
23-41
DEUTSCH EINFÜHRUNG

Contents
1.0 Important safety information
2.0 About this product
2.1 Specifications
2.2 Install the SYMA FLY app
2.3 Drone diagram
2.4 Remote control diagram
3.0 Assembling the product
3.1 Removing the Drone
3.2 Fixing the propeller
3.3 Installing the propeller protectors
3.4 Attaching the phone holder
3.5 Charging the drone battery
3.6 Instruction of remote control
4.0 Flight guide
4.1 Flight preparation and turning the drone on/off
4.2 Using the remote controller
4.3 Stunt functions
4.4 Trimming
5.0 Function introduction
6.0 Contact Us
7.0 Accessories/Parts (Optional)
2
3
5
7
11
3
3
4
4
5
5
6
6
7
7
9
11
14
15
16
5
1
EN

2
EN
1.0 Important safety information
Safety Guide
Repair and maintenance
Thank you for purchasing this SYMA product. To ensure that you operate the aircraft correctly and
conveniently, please read these instructions carefully before first use and store them in a safe place for
future reference.
1. Please store the smaller-sized drone accessories in places that are out of reach of children.
2. This drone is very powerful. For all first-time flights, the left joystick must be slowly pushed up in
order to prevent the drone from ascending too fast to avoid unnecessary collision and possible
damage and injury.
3. When the flight is ended, first turn off the power of the remote control. Then turn off the power of the
drone.
4. Avoid placing the batteries in places with high temperatures and exposure to heat.
5. Take extra precaution to ensure that the drone is at a minimum distance of 15 feet from the pilot,
other people, and animals in order to prevent bodily injury during flight operation. A minimum
separation distance of 20 cm must be maintained between the user's body and the device under
normal use condition.
6. Children under the age of 8 must be instructed in the correct and safe operation of the drone by an
adult.
7. The children must be under adult supervision when using this drone.
8. Non-rechargeable batteries are not to be recharged; Batteries are to be inserted with the correct
polarity; Different types of batteries or new and used batteries are not be mixed.
9. When the drone is not in use, please remove the batteries in the remote control.
10. The supply terminals are not be short-circuited.
11. Discharge the battery to 40%-50% (On a full charge, fly for half of the total flight time) if it will not be
used for 10 days or more, this can greatly extend the battery life.
12. Please keep a safe distance from the spinning propellers to avoid injury.
13. To ensure the electromagnetic environment requirement of the aviation radio (station), using
remote controls in the zone, which is in a radius of about 5000m zone from the circle center of the
airport runway, is forbidden. All users also should abide by the regulation of the radio set forth by
government and regulatory agencies including the duration and area.
14. Only uses the recommended transformer for the model, and the transformer is not a toy. Check the
cord, plug, enclosure and other parts of the transformer regularly. If any damages have been
discovered, please immediately stop using it, until it was completely repaired.
15. Never look steadily at the laser beam since the laser radiation.
16. Attention: Drone assembly under adult supervision.
17. The pilot is responsible for the safe operation and safe distance from uninvolved persons and
property on the ground and from other airspace users and shall never fly the drone above crowds (> 12
persons).
18. Open the battery cover of the toy with screwdriver.
19. The packing has to be kept since it contains important information.
1. Use dry and soft cloth to clean this product.
2. Avoid exposing this product to heat.
3. Do not immerse this product in water, otherwise, the electronic parts will be damaged.
4. Check the cord, plug, enclosure and other parts regularly. If any damages have been discovered,
please immediately stop using it, until it was completely repaired.

2.0 About this product
2.1 Specifications
Drone
Drone weight Approx. 107g
Drone Size 200x200x103 mm
Brand Name SYMA
Model/ITEM NO. X110W
Remote control
Operating Frequency 2.4 GHz
Range 30m
Battery 4X1.5V"AA"(Not included)
Package contents
Drone 1
Remote control 1
USB charging cable 1
Propeller
Propeller protector
2 (A/B)
4
2.2 Install the SYMA Fly app
1. Scan the QR code with your mobile device or download the app from your app store.
AndroidiOS
*For best results, use a device with iOS 8.0/Android 5.0 or later.
Note:
Flight time Approx. 12 mins
Motor ø8
Battery 3.7V 1100mAh
Charging time Approx. 100 minutes
Screwdriver 1
Phone holder 1
User manual 1
3
EN

2.4 Remote control diagram
2.3 Drone diagram
①
②
③
④
⑤
① Power switch
② Left joystick
(press and hold for trimming
adjustment and release
when finished)
③ Phone holder
④ Right joystick
(short press to toggle between
high and low speed mode)
⑤ One-key take off/landing button
4
EN
2. SYMA FLY App Connection operation
① Install the SMYA FLY app on your phone. Note: Scan the QR code with your mobile device
or download it from the app store.
② First pair the drone with the remote control, then turn on the WiFi Settings of the mobile
device and select FPV_WIFI_**** from the WiFi list.
③ Wait a few seconds until your smartphone connects to the drone's WiFi network.
④ Open the Syma fly application, select the corresponding model, and then click Start, the
camera image will be displayed on the screen, indicating that the connection is successful.
① Propeller protector
② Motor
③ Propellers
④ Battery
⑤ Camera
①
②
③
④
⑤

3.1 Removing the Drone
3.2 Fixing the propeller
3.3 Installing the propeller protectors
3.0 Assembling the product
1. Fully unfold the arms of the drone as
shown by the arrows.
2. To fix the arms, push inwards the locks
at the bottom of the arms.
5
EN
Remove the plastic transparent cover (lift it up), then the battery and the battery locating ring. After,
remove the drone from the charging cradle.
Insert the back side of the propeller guard
into the side of the arm as indicated by the
arrow.
Tips：Base and top cover with accessories
1. Propeller protector
2. USB charging cable
3. Propeller

Attaching the phone holder
3.5 Charging the drone battery
1. Rechargeable batteries should be removed from the toy before being charged.
2. Rechargeable batteries should only be charged under the supervision of adults.
3. Exhausted batteries should be removed from the aircraft.
4. Caution: Risk of explosion if battery is replaced with incorrect ones. Please dispose the batteries
according to the instructions.
5. Don't use or leave the battery near a heat source such as fire or heater.
6. After flying, don't charge batteries at once to avoid batteries too heat to cause to the fire, make sure
it cool down before charging.
7. Don't hit or let batteries fall down when charging to avoid inner short-circuit.
8. Only use the included adaptor for charging. Please replace with new batteries in time if batteries
aging.
9. After full charging, please take off adaptor in time, otherwise batteries will discharge and charge
again, this way will shorten batteries service life.
10. The toy is only to be connected to equipment bearing either of the following symbols:
3.4 Mobile phone clip installation
Insert the phone holder
into the opening on the
remote control.
Press the spring to
adjust the size of
the phone holder.
12
6
EN
Battery Warning:
!
1. To remove the battery, press on the release buttons and at the same time pull out the battery.
2. Connect the USB cable with the charging cradle. After, plug the USB into a power outlet and the
charging cradle light will glow red. Insert the battery into the charging cradle and the light will turn
green. The light indicator is off when fully charged.
3. Once charging is complete, install the battery into the drone.
12 3

Note:
!
* When installing the batteries, ensure that you match the + and ‒ ends of the battery with the + and ‒
signs on the controller.
* During the battery installation, it must be ensured that the polarities of the batteries are matched
with that of the battery box. No battery shall be installed with the opposite polarity.
* Please do not use new and old batteries together.
* Please do not use different types of batteries together.
* Remote control does not use rechargeable batteries.
* Exhausted batteries are to be removed from the Remote control.
Note:
!
1. Turn on the drone in the order of ①②③④.
2. After you switch on the remote control, the indicator will flash quickly to indicate that the
remote control is waiting to pair with the drone.
Pairing the remote control with the drone
4.0 Flight guide
4.1 Flight preparation and turning the drone on/off
The indicator will stay constant
when pairing is complete.
Switch on the remote control Indicator
flashes rapidly→slowly.
2
3
4
Remote control indicator
flashes rapidly
1
To insert the controller batteries, open the battery cover on the back of the remote control and insert
4x AA alkaline batteries, ensuring that you observe the polarity markings (batteries are not included
and must be purchased separately).
3.6 Instruction of remote control
Battery cover
4x AA batteries
7
EN

8
EN
Turning the drone on
Push to the highest point and
return to the center.
Pull the joysticks in a V shape Press the ascend/descend button
Note:
!
1. If the drone is flown out of range from the remote control, the drone indicator light will start to flash
and the drone will land slowly.
2. If the remote control suddenly turns off or runs out of power during flight, the drone will
automatically land and come to a stop. If the remote control is turned back on during this process,
you will be able to control the drone again.
Note:
!
When the drone body tilts more than 90 degrees, the drone shuts down by itself.
Method one Method two Method three
Method one Method two Method three
Push to the bottom for 2-3 seconds Pull the joysticks in a V shape Press the ascend/descend button
Turning the drone off
2
1

9
EN
Ascend
Descend
Move forwards
Move Backwards
Rotate right
Front
Rotate left
Rear
Tilt left Tilt right
Front
Rear
4.2 Using the remote controller

10
EN
Trimming
When the drone is hovering in the air, when it flies forward / backward automatically, you can press
and hold the left fine-tuning button and push the right joystick in the backward / forward direction to
adjust it until the drone is stable and then release it.
When the drone drifts to the left or right when it is hovering, hold the left joystick down and push the
right joystick right/left until the drone stops drifting.
Trimming forwards and backwards
Trimming left and right

11
EN
4.3 Function introduction
Undervoltage protection
Overcurrent protection
4.4 Flight control
Horizontal calibration function
When the two indicators on the nose of the drone begin to flash, it means that
the power of the drone is low. At this time, please control the drone to return.
If the drone's blades collide with another object or become stuck, the drone's
circuit will engage the overcurrent protection mechanism.
Place the drone on a level surface and move the left and right joysticks to the lower right corner for
approximately 3 seconds. The indicator will flash rapidly and then stay constant to indicate that the
calibration process is complete.

12
EN
Short press the fast and slow button to switch the fast/slow mode.
1.The default is slow mode when power on.
2. The remote control emits two beeps for fast mode and one beep for slow mode.
High/low speed mode
One-touch take-off/landing
1. When the drone is in standby, press the take-off button to make the drone take off
automatically and hover at a height of 1.5 m.
2. When the drone is in the air, press the one-touch take-off/landing button to make the
drone land automatically.

13
EN
Altitude hold
In headless mode, push the right joystick of the remote control to fly forward, the drone
will always fly in the direction indicated by the nose when it takes off, even if the direction
of the nose is changed during the flight.
Headless mode
When you release the left joystick (throttle) after ascending/descending, the drone will
continue to hover at the current height.

5.0 Drone status and maintenance
Problem
The drone does
not respond.
The drone does not hold
the set altitude.
The drone is unstable
when hovering or quickly
drifts in one direction.
Reason Solution
The drone has activated low-voltage
battery protection.
Beyond flight distance
Balance calibration is needed
Do not fly out of the transmitter's
range.
Perform balance calibration.
1. Balance calibration is needed.
2. Flying the drone in severe weather.
3. Heavy crash impacts gyroscope
calculations.
1. Perform balance calibration.
2.Avoid flying the drone in severe
weather conditions(strong
wind, rain, snow, fog, thunder
etc).
3. Perform balance calibration.
Numerous crashes. Re-set forward direction.
Recharge the drone's battery.
The transmitter sticks
are not sensitive.
When in headless mode
the forward direction
deviates.
14
EN
1. Define the front
When you turn on the power for the first time and start the drone, the direction of the nose of
the drone is straight ahead.
3. To define the forward direction function correction
2. Enter and Exit of Headless Mode
① After the pairing is completed, short press the "Headless Mode" button, the remote
control will emit a "Di Di Di..." sound, and the indicator light on the aircraft will flash slowly,
indicating that it has entered the headless state; short press the "Headless Mode" button
again. When you hear a long beep of "di", it will exit the headless state.
② In the headless state, the operator does not need to identify the position of the nose of
the aircraft, but only needs to control the aircraft according to the direction of the joystick
of the remote controller.
When the drone collides in the headless state, if it is found
that the headless direction is deviated, just land the
aircraft to the ground, and after correcting the
direction,the drone restarts, the direction the nose points
to is straight ahead in headless mode.

Please do not hesitate to contact us if you need more further support.
[email protected]
[phone](US) [phone](UK) [phone](DE)
6.0 Contact Us
For online support, please scan this code with Facebook Messenger
15
EN

7.0 Accessories (available separately)
The following section contains a list of optional accessories that are available to purchase.
Accessories can be purchased from your local retailer. Please indicate your preferred colour
when making your purchase.
16
EN
Main Body Main Body Top Shield Main Body Bottom
Shield
Battery
Transparent Cover Arm A Arm B
Blade Protective
Guard
Blade A Blade B
Charging Cradle WiFi unit Circuit Board

17
EN