Syma X220w User manual

X220W GPS DRONE

User manual

Contents 1-23EN ENGLISHINTRODUCTION 24 - 47DEUTSCH EINFÜHRUNG

Contents1.0 Important safety information2.0 About this product2.1 Speciﬁcations2.2 Install the SYMA Air app3.0 Assembling the product3.1 Installing the propellers3.2 Installing the propeller protectors3.3 Charging the drone battery4.0 Flight guide4.1 Flight preparation and turning the drone on/oﬀ4.2 Using the remote controller4.3 Flight modes4.4 Flight control4.5 Smart app features5.1 Understanding the drone LED indicators5.2 Troubleshooting5.3 Contact Us 5.0 Drone status and maintenance6.0 Accessories/Parts (Optional)2381718342.3 Drone diagram2.4 Remote control diagram445563.4 Preparing the remote control781011131617171751

1.0 Important safety informationSafety GuideThank you for purchasing this SYMA product. To ensure that you operate the drone correctly and conveniently, please read this manual carefully before operating, and keep this manual properly for future reference.1. Adult or experienced RC pilot’s supervision is recommended for children.2. Rechargeable batteries are to be removed from the toy before being charged.3. Batteries are to be inserted with the correct polarity.4. Rechargeable batteries are only to be charged under adult supervision.5. Non-rechargeable batteries should not be recharged; Batteries should be inserted with a correct polarity; Diﬀerent types of batteries, new or used batteries should not be mixing.6. Turn oﬀ the drone/transmitter and remove the batteries when not in use.7. The supply terminals are not be short-circuited.8. Keep away from the rotating blades (rotating blades may cause bodily injuries, or damage to property).9. Attention：please assemble the drone with the guidance of adults.10. Do not look directly into the LED lights of the drone as it can damage your eyes.11. Exhausted batteries are to be removed from the drone.12. Please store the smaller-sized drone accessories in places that are out of reach of children.13. This drone is very powerful. For all ﬁrst-time ﬂights, the left joystick must be slowly pushed up in order to prevent the drone from ascending too fast to avoid unnecessary collision and possible damage and injury.14. When the ﬂight is ended, ﬁrst turn oﬀ the power of the remote control. Then turn oﬀ the power of the drone.15. Avoid placing the batteries in places with high temperatures and exposure to heat.16. Please keep a safe distance from the spinning propellers to avoid injury.17. To ensure the electromagnetic environment requirement of the aviation radio (station), using remote controls in the zone, which is in a radius of about 5000m zone from the circle center of the airport runway, is forbidden. All users also should abide by the regulation of the radio set forth by government and regulatory agencies including the duration and area.18. Pay attention to keeping distance of 2-3 meters from the user or other people when the drone is ﬂying, avoid the drone landin to hit the head, face or face or body of anoter person.19. Attention：Drone assembly under adult supervision.20. The packing has to be kept since it contains important information.Repair and maintenance1. Use clean and soft cloth to clean the product.2. Keep away the product from heat sources.3. Avoid water exposure to this product. Moisture may cause damages of drone electronic parts.4. Transformers used with the drone should be examined regularly, such as propel blade, motor, battery and other parts. In case of any damages is found, please stop using it unless it is repaired or replaced.2

2.0 About this product2.1 SpeciﬁcationsDroneDrone weightApprox. 190g(Not included propeller protector)Drone Size 360*300*70mm(Install propeller protector)Brand Name SYMAModel/ITEM NO. X220WRange 350mAltitude100mImage transmission range300mOperating temperature0°C to 40°CVideo transmission frequency5 G Motor8520Battery7.6V 1300mAhCharging timeApprox. 150 minutesFlight time Hovers indoors for more than 16-18 minutesParameter of shootingOperating Frequency5 GHzPhoto Resolution 3840*2160(stored on mobile phone)Video Resolution2048*1080(stored on mobile phone)Lens FOV 62°Max Transmission Distance984 feet/300m(outdoor and unobstructed)FPV Real-time Transmission720p@25fps Photo FormatsJPEG Video FormatsMP4Whether to support memory card Not supportControllable range90°up and downRemote controlOperating Frequency2.4 GHzRange300mOperating temperature0°C to 40°CRemote control battery 4*1.5V "AAA" (Not included)Package contentsDrone1Remote control1User manual 1USB charging cable1Clockwise/anticlockwise propellers2Propeller protectors4

2.4 Remote control diagram2.3 Drone diagram4

2.2 Install the SYMA Air appScan the QR code with your mobile device or download the app from your app store.

AndroidAndroid(Google play)iOS

PropellerprotectorMotorPropeller bladesFront cameraPower switchRear LED indicatorBatteryBottom cameraFront LED indicatorPhoto buttonPhone holderLens upLens downRight joystickRecord buttonLeft joystickPower switchReturn to take-oﬀ positionOne-touch Take oﬀ / LandingCalibrating the compass*For best results, use a device with iOS 8.0/Android 5.0 or laterNote:!

3.1 Installing the propellers3.2 Installing the propeller protectors3.0 Assembling the productClockwise propellersAnticlockwise propellers5

1. Attach the propellers as shown in the diagrams above. Ensure that they are attached in the correct orientation.2. Ensure that the clockwise and anticlockwise propellers are attached to the correct arms. The drone will not ﬂy correctly if the propellers are attached in the wrong position.3. The propellers are made from delicate material. Pay attention when attaching them to the drone.4. Only use propellers that are supplied by the SYMA.5. The propellers are consumable parts. If necessary, purchase replacements from the manufacturer.Note:!

Remove the batteryInsert the battery3.3 Charging the drone battery6

5V/2A adapter(Not included)USB charging cableBatteryBattery* The toy is only to be connected to equipment bearing either of the following symbols: * Charge the drone with the USB charging cable that came with the product.* The battery will take longer to charge when you use an adapter with a smaller rated current.Ensure that the battery holder clicks into place.Note:!

* Do not short circuit or compress the battery, as this may cause an explosion.* Do not disassemble the battery or store it in a hot environment.* If you do not plan to use the drone for at least 10 days, discharge the battery to 40%-50%. This helps to prolong the lifespan of the battery.* Rechargeable batteries should be removed from the drone before charging.* Rechargeable batteries should only be charged under the supervision of adults. And keep away from ﬂammable materials.* Caution: Risk of explosion if the battery is replaced with incorrect ones, please install the batteries according to the instructions.* Failure to follow all the instructions may result in serious injury, irreparable damage to the battery, and may cause a ﬁre, smoke, or explosion.Note:!Note:!When charging: the battery green indicator ﬂashes slowly.When fully charged: the battery green indicator light is always on.Abnormal charging: the battery indicator ﬂashes quickly.

Remote control battery installation3.4 Preparing the remote control7

Battery CompartmentBattery Cover4×1.5V "AAA" Battery(Not included)* Always check the battery's condition before charging or using it. Replace the battery if it has been dropped, or in case of odor, overheating, discoloration, deformation, or leakage.* Use only the supplied charging cable.* The battery temperature must never exceed 60℃(140°F) otherwise the battery could be damaged or ignite.* Never charge on a ﬂammable surface, near ﬂammable products, or inside a vehicle ( preferably place the battery in a non-ﬂammable and non-conductive container)* When installing the batteries, ensure that you match the + and ‒ ends of the battery with the + and ‒ signs on the controller.* During the battery installation, it must be ensured that the polarities of the batteries are matched with that of the battery box. No battery shall be installed with the opposite polarity.* Please do not use new and old batteries together.* Please do not use diﬀerent types of batteries together.* Do not use rechargeable batteries.Note:!Open the remote controlClose the remote control

Indicator lights stays constantwhen pairing is complete.Switch on the remote control Indicator lightsﬂashes rapidly to slowly8

Remote control indicator lights ﬂashes rapidlyPairing the remote control with the drone4.0 Flight guide4.1 Flight preparation and turning the drone on/oﬀCalibrating the compassPress to calibrating the compassHold the drone horizontally and rotate 360 degrees a few times. Indicator lights ﬂashes from slowly to rapidlyHold the drone vertically and rotate 360 degrees a few times. Indicator lights ﬂashes from rapidly to constant

2 3

* When you switch on the remote control, the indicator light will ﬂash rapidly for approximately 20 seconds to indicate that the remote control is waiting for a signal. The indicator will then ﬂash slowly to indicate that the pairing mode has been disabled.Note:!

* Do not calibrate the compass near strong electromagnetic ﬁelds or large pieces of metal, car parks or buildings with underground steel reinforcements.* When holding the drone horizontally, the angle of inclination must not exceed 30 degrees.Note:!

Turning the drone oﬀMethod oneMethod twoMethod threePush the left joystick downward for 2-3 seconds.Push the left and right joysticks downward in a V shape for 2 secondsPress the take-oﬀ/landing button to make the drone land automatically and switch oﬀ.Turning the drone onPush the left and right joysticks downward in a V shape for 1 second.Move the left joystick upwardor* The drone will switch oﬀ automatically if its angle of inclination exceeds 90 degrees.Note:!

Searching for satellites (No need to search for satellites for indoor ﬂight)* The rear indicator light will change from orange to green when the drone has locked onto a satellite and recorded the take-oﬀ location. The drone is now ready to ﬂy.* It should take approximately one minute for the drone to lock onto a satellite. If the drone fails to ﬁnd a satellite, recalibrate the compass.* Before take-oﬀ, place the drone in an open space away from obstacles and ensure that GPS mode is enabled.* When the rear green indicator light ﬂashes rapidly, this indicates that the GPS signal is weak. If this occurs, land the drone manually and restart the satellite search.

4.2 Using the remote controllerAscendDescendMove backwardsMove forwardsTilt leftTilt rightFrontRearRotate rightFrontRotate leftRear

4.3 Flight modesFront indicator is constant white, rear indicator is constant yellow.Optical ﬂow positioningGPS modeFront indicator is constant white, rear indicator is constant green.*If the rear indicator starts to ﬂash rapidly, this indicates that the optical signal is weak and the drone cannot determine its position.* Performance may be impaired in dark surroundings, areas with reﬂective surfaces (e.g. water), or at altitudes of more than 6 m.* Optical ﬂow positioning only supports altitudes of less than 6 m.Note:!

* When the battery level is normal, the drone can ﬂy to a distance of 350 m at a maximum altitude of 100 m.* When the battery level is low, the drone can ﬂy to a distance of 20 m at a maximum altitude of 20 m.* If the rear indicator starts to ﬂash rapidly, this indicates that the GPS signal is weak and the drone cannot determine its position.* GPS mode cannot be used indoors.Note:!

1. Conﬁguring the forward directionWhen you switch on the drone for the ﬁrst time, the direction in which the front side of the drone is pointing will be set as the forwards direction.2. Enabling headless mode① After pairing the remote control with the drone, hold down the right joystick for approximately 3 seconds. The remote control will beep 8 times to indicate that headless mode is enabled. To disable headless mode, hold down the right joystick again for approximately 3 seconds.② In headless mode, you do not need to determine the drone orientation. You can move the joysticks on the remote control to make the drone move in the corresponding direction.Headless modeThe indicator on the drone will ﬂash once every 4 seconds.

4.4 Flight controlLevel calibrationHigh/low speed modePlace the drone on a level surface and move the left and right joysticks to the lower right corner for approximately 3 seconds. The indicator will ﬂash rapidly and then stay constant to indicate that the calibration process is complete.The drone cannot be calibrated if the angle of inclination is greater than 10 degrees.Brieﬂy press the right joystick to switch between high and low speed mode.1. Low speed mode is enabled by default when the drone is switched on.2. The remote control beeps twice when high speed mode is enabled and once when low speed mode is enabled.

One-Key take-oﬀ/landingRemote control photo and video functionsTake a photoRecord videoLens upLens down90°1. When the drone is under standby mode,Press the take-oﬀ/landing button to make the drone take oﬀ automatically and hover at a height of 1.5 m.2. When the drone is under the active mode, it will automatically land on the ground if you press the one key landing.1. Take a photo: Press the photo button. The indicator on the drone will ﬂash to indicate that a photo is taken.2. Record video: Press the record button. The indicator on the drone will ﬂash twice to indicate that recording is in progress. Press the record button again to end the recording. The indicator on the drone will turn on to indicate that recording is complete.3. Camera angle adjustment

Return to home functionNo signalFailsafe return to homeIn GPS mode (when the indicator light is constant), hold the return to home, button so the drone will return to its take-oﬀ position automatically. During the return ﬂight, you can use the joystick to control the drone ascend, descend and move left/right in order to avoid obstacles. To terminate the return ﬂight, hold the return to home button.If the remote control signal is lost for more than 20 seconds, the drone will automatically return to the take-oﬀ position. If the signal is restored during the return ﬂight, you can hold the return to home button to terminate the return ﬂight.· The drone cannot automatically avoid obstacles during the return ﬂight.· The automatic return to home function is not available when the GPS signal is weak (ﬂashing indicator light).· If the drone does not receive a GPS signal and lost contact with the remote control for more than 20 seconds, it will not be able to return to home but will land automatically.· If the drone is ﬂying at an altitude less than 20 m, it will automatically ascend to an altitude of 20 m before returning home.· If the drone is ﬂying at an altitude more than 20 m, it will return home at the same altitude.

Low-battery return to homeLow battery4.5 Smart app featuresWhen the drone battery is low, the drone will automatically return to the take-oﬀ position. During the return ﬂight, you can use the joystick to control the drone to ascend, descend and move left/right in order to avoid obstacles.·If the drone is further than 20 m from the landing position, the return ﬂight cannot be terminated.·If the drone is less than 20 m from the landing position, the return ﬂight can be terminated. Landing position: The initial unlock/take-oﬀ position.· Before using the smart app features, watch the video tutorial in the SYMA AIR app or on the SYMA website.· Ensure that you pre-conﬁgure the ﬂight altitude and distance in the SYMA AIR app.Optical flow

Joystick On / Off

Photo / Video

Record

Front camera pan controller

Flight Plan

Circle flight

Flight plan / waypoint flight

Switch camera

5.0 Drone status and maintenance5.1 Understanding the drone LED indicators1234567895.2 TroubleshootingPlease do not hesitate to contact us if you need more further support. [email protected] +1 718-312-0558(US) +44 (0)7723708421(UK) +4933545519201(DE)5.3 Contact UsFor online support, please scan this code with Facebook MessengerProblemCauseCause SolutionNo.Indicator statusMeaning1. Undervoltage protection was enabled.2. The remote control battery level is low and the power indicator is ﬂashing. 1. The remote control batteries are nearly empty.2. There is interference from a remote control on the same frequency.1. Charge the drone battery.2. Change the batteries in the remote control.1. Change the batteries.2. Move to a diﬀerent area where there is no interference.The drone is not calibrated level to the ground.1. The drone is not calibrated level to the ground.2. The air pressure is unstable due to poor weather conditions.3. A violent collision corrupted the gyroscope’s data.1. Calibrate the drone.2. Avoid ﬂying in poor weather.3. Calibrate the drone.The dronewas involved in a collision.Calibrate the drone.Reconﬁgure the forwards direction.The drone doesnot respond. The drone’sresponse isintermittent. The drone drifts to one side while hovering.The drone does not travel in a forwards direction in headless mode.The drone does not hover properly/the drone keeps moving up and down.Front indicator = constant white, rear indicator = constant yellowFront indicator = constant white, rear indicator = constant greenFront and rear indicators ﬂash once every 4 secondsFront and rear indicators ﬂash twice every 1.5 secondsFront and rear indicators ﬂash twice every secondFront and rear indicators ﬂash once every secondFront indicator = constant, rear indicator = ﬂashing slowlyFront indicator = constant, rear indicator = ﬂashing rapidlyFront and rear indicators ﬂash rapidlyPairing or level calibration in progressRecording in progressSignal lostLow batteryPoor GPS receptionGPS faultHeadless modeGPS modeOptical ﬂow positioning