SYMA GYRO S107C Datasheet

AGE {4+
HELICOPTER USING INSTRUCTION
,// 4
//fl t
fl/0t
a /.,
To avoid copterrs damage and player's injury, please read this instruction before flying!

1. Placed in small parts of the reach of children, to avoid accidents.
2. The blades of this helicopter is used activities blades,don't screw up.
3. The helicopter.was powerful, should be gradually pushed up the remote control shift
lever on the left for first flight, to avoid the surge caused the helicopter crash damage.
4. Should be turn off the power of controller first then turn off the power of the helicopter
when finished flight.
5. Do not place the battery in high temperature, heating place(e.g:fire or electric heating
devices)
6. Note that when the helicopter to keep the user or other persons from 2-3 mto avoid the
helicopter flight, landing crashed into another person's head, face and body and so on.
7. Children should control the helicopter by adults in the guidance and ensure the helicopter
control in manipulator (or guides) line of sight range, easy to control.
8. Non-rechargeable battery is not charging,installation the lithium battery,please note that
the battery polarity. Do not mix old batteries and new batteries or different type batteries.
9. Should be tum off the power of the controller and helicopter when not in use.
10. Power terminal is not allow short circuiting.
1. Please recheck the ground, keep away from the crowds, animals and other barriers.
2. Tum the remote control on, after a while, the LEDs will be flashing. Push the motive handle must
be pushed to the maximum control route of travel first, then adjust it to the lowest; When the
remote control LEDs keep lighting, it means the helicopter is going to fly.
3. Move Power Swithch on the helicopter the the "ON"position, after that, the power indicator will
light up; Place the helicopter on the ground for some seconds,then the helicopter is going to fly.
4. Push the motive handle slowly, then the helicopter will fly up.
Low volatage protection: When the helicopter power is wealq helicopter control system will protect the
battery and the power supply to the helicopter blades will be stopped.
After low volatage protection, it can fly again ifthe helicopter charged.
1. Cleaning the helicopter with clean and soft cloth.
2. Don't put the helicopter under the direct sun or strong lighting
3. Don't soak the toys in the water, or the electronic parts will be destructed.
4. Regularly check the plug and other spare parts, if find some parts broken, please soppi*ne
using till the product in good condition.

Assembly transmitter
Battery cover
6 X l.5VAA
batteries
1. Install batteries: open the cover ofbattery case, insert 4 batteries (size 1.5v AA) properly
Battery-Helicopter
A. Controller charging While charge, pull out the switch of
thc helcopter to "OFF !posidon up.
1. Move the power switch on the helicopter to the "OFF" position.
2. Charging way A: Put dosn the charging wire cover of the back controller and put out the charging
l-ire. then put into the interface ofthe helicopter, the red LED on the controller
C[LA. u'ill turn on. The charging time is about 40-50 minutes.
When charging completed, red LED on the controller CHA will tum off.
The fught time about 5-6 minutes.
Charging way B: Put the USB charging wire into the computer USB interface, the charging wire
will be light. Put the other side of USB charging wire into the helicopter's
interFace. USB charging wire tight will be tum off. The charging time is about
40-50 minutes. Charging wire light will turn on. Then the helicopter is fu11y
charged. The flight time about 5-6 minutes.
- Helicopter is equipped with a Li-Poly battery, please also pay attention to the following cautions or
safety use.
- Do not use or leave the battery near a heat source such as fire or heater. Otherwise it will cause
damage or explode.
- Do not use the battery slam or beating hard surface.
- Do not immerse the battery in water, and keep the battery in a cool dry place.
- Charger included with the product can only be used for the product charge.
- Do not disassemble the battery.
- Never leave the battery unattended during charging.
follo*'ed by polar indicator. (batteries to be purchased)
B. USB charging

Push tle rudder stick toward left to tum counter
clockwise.
When you press the shoot button, the
camera on the red light camera to take
a picture, the button is loosened, the red
light camera. ( click on a photo shoot )
When you push up the left stick
(throttle) the speed ofthe main
rotor blade will increase and the
helicopter will go up.
When you pull down the left stick
(throttle) the speed ofthe main
rotor blade will decrease and the
helicopter will go down.
When you push doriln the right control lever
(steering rudder), the nose incline to up, the
helicopter is moving to backward.
I when once again press the camera button.
] red light camera camera. enter an offstate.
Push the rudder stick toward right to turn
clockwise.
Press the camera button, the camera on the
red light, helicopter camera into camera state;
When the helicopter tail presents the
clockwise rotation, you may the
comterclockwise rotation you in the
hmd the remote control vemier
adjustment knob until balanced.
The tail lin aim at the operator.
When the helicopter tail presents the
comterclockwise rotation, you may
the clockwise rotation you in the
hmd the remote control vemier
adjustment knob until balmced.
The tail lin aim at the operator.
When you push up the right control lever
(steering rudder), the nose incline to down, the
helicopter is moving to lorward.
J

Install cameras method:
Connected the wire, put the hook
hole of camera aim clevis joint, and
pushed forward the end.
(Cameras can be adjusted at will angle
Problem Cause Check this
No reaction
from the
helicopter
1. Not enough power for the helicoper.
2. Not enough power for the controller.
3. The chmel q.a different ftom helicopter and the
controller.
4. The glro ofthe helicopter can't find out the right
point.
1. Should be chuging for the helicopter.
2. Change new batteries instead.
3. Make sue the same channel flom helicopter and
the controller.
4. Move the helicopter onto the flat gromd, when
the gyro receive the signal,then open the controller.
Not reaction
from the
helicopter
when was fly
1. By sunlight or intense light inadiation effects.
2. Have the me frequency remote conhol
trmmitter-
1. Move the helicopter onto without sunlight or
intense light.
2. Not the same for a lamch interference.
Order bv number from local distributors.
item IWWW
WMWWW
s107c-11 S107C-12 S107C_13 S107C_14 S107C_1s
Main fiame metal part A Main fiame meral part B Tail support pipe Main shaft Main shaft pipe
WMreWre
s107c-07
Tail blade
s107c-r7
Motor A
s107c-08
Tail decoration
s107c-18
Motor B
s107c-10
Balance bar
s107c-20
3.7V Li-Poly
rcTreWW
s107c-01
Head cover
s107c-06
Main blades
s107c-16
Chopper tail unit module
&--*"e
@^ .- -)
k* *:d
s107c-02
Main frame s107c-03
Ascend and descend s107c-04
Camera box
s107c-09
Gear
s107c-19
Circuit board
s107c-05
Connect buckle

H-_ o,
Or------F
H
"o19

Ltem Number Description Qty Need
01 Balance bar 1
02 Connect buckle 2
03 Upper blades grip set 1
04 Upper blades 2
05 Lower blades grip set 1
06 Lower blades 2
07 lnner shaft base 1
OB Motor B1
09 MotorA 1
10 Tail blade 1
11 Tailmotor 1
12 Verticalfin 1
13 Tail pipe setof compnenb 1
14 Main frame 1
15 Left protect ftarc(upper) 1
16 Left protec{ ftanc(lovcr) 1
17 Right pmtect ftame(upper) 1
18 Ri g ht proted toame(lorer) 1
19 Upper blades gear 1
20 Transition gear 2
21 Lowr blades gear 1
22 Battery 1
23 PCB 1
24 Chassis 1
25 Head cover 1
26 Camera 1
27 Landing skids 1
Ltem Number Description Qty Need