Symmons Ultra-Sense S-6080 Quick guide

IMPORTANT:
Water lines MUST be thoroughly flushed BEFORE and
AFTER installing the faucet to prevent foreign matter, i.e.
copper chips, sand, stones, etc. from clogging and possibly
damaging the faucet.
GENERAL
This installation and Maintenance Guide introduces the
installation, maintenance and use of the Ultra-Sense faucet.
Please read the instructions carefully prior to the installation
and save them for reference where service may be needed.
If any fault or malfunction occurs in the faucet, please refer
to the troubleshooting chart, or contact Symmons Customer
Service at 1-800-SYMMONS.
TECHNICAL DATA
Aer ow period: 1 second■
Maximum water ow period: 10 seconds■
Electrical installation: 2CR5 6V Lithium Battery■
Working pressure: 14.5psi - 145psi■
Normal water ow: .25GAL/cycle■
INSTALLATION
Every S-6080 Series faucet can be installed in one of three
possible supply configurations.
OPTIONS
Hot and cold supply with lever handle temperature■
adjustment. (factory standard)
Hot and cold supply with preset tempered water.■
(eld modied)
Single supply for pre-mixed water. (eld modied)■
OPTION 1
For 4” center deckplate installation, place faucet and■
supply(s) through deck plate (SF-138).
Ax deck plate with studs facing down to faucet using two■
screws (SF-143) provided in mounting kit (SF-142).
NOTE: For S-6080-LST (18” long copper supply tube)
thread supply tubes into faucet housing. Tubes thread into
base with LEFT hand thread. Be sure brass tube bushing
with o-ring is fully installed in base and tight.
Mount the faucet on the wash basin using anchor bar (KN-■
23), spacer (KN-26), and nut (L-36) on 4” centers. Ensure
the gasket (SF-140) is correctly positioned between the
faucet and wash basin. For single hole mount installation,
attach studs found in single mount kit (SF-158) to base of
1
2 3
Lavatory Faucet S-6080
Battery Powered, Sensor-Operated
Installation and Service Instructions
Ultra-Sense™
housing. Place faucet supply(s) through wash basin and
secure using wing xing plate and nuts from single mount kit.
Attach supply hose(s) (SF-148) to check strainer assembly■
(SF-186).
Connect check strainer assembly (SF-186) to angle stop or■
water inlet pipe.
NOTE: For S-6080-LST (18” long copper supply tubes) attach
check strainer assembly (SF-181) directly to supply stops. Cut
tubing to proper length and attach tubing to check strainer
assembly using nut (IL-8)) and ferrule (IL-9).OPTION 2
Modifying the faucet for hot and cold supply with
tempered water
Remove handle screw (SF-155), handle (SF-154) and■
handle limit stop (SF-156).

Reinstall handle (SF-154) and adjust the temperature as■
required.
Remove handle (SF-154) and push plug (SF-153) in place■
of the handle.
Continue with Option 1 installation instructions.■
OPTION 3
Modifying the faucet for single supply pre-mixed water
Detach parts (SF-155), (SF-154) and (SF-156).■
Unscrew the exible hot water supply hose (SF-148).■
Note: le hand thread.
Screw on the plug (SF-159) in place of the supply hose.■
Reinstall the temperature adjustment handle (SF-154) and■
turn counterclockwise (cold position) as far as it goes.
Push the plug (SF-153) in place of the temperature■
adjustment handle.
Continue with option 1 installation instructions.■
Limiting the water temperature
S-6080 with temperature adjustment handle
Remove handle screw (SF-155) and handle (SF-154).■
To limit the maximum water temperature, turn the handle■
limit stop (SF-156) clockwise.
To increase the maximum water temperature, turn the■
handle limit stop (SF-156) counter clockwise.
Reinstall handle reversing steps above.■
S-6080 with preset water temperature
Remove plug (SF-153).■
To limit the maximum water temperature, insert handle■
(SF-154) in faucet and turn it counter clockwise.
To increase temperature turn handle (SF-154) clockwise.■
Remove handle (SF-154) and reinstall plug (SF-153)■
1 9/16" - 1 3/8"
33mm - 35mm 4 13/32"
112mm
21/2"
64mm
6" (152mm)
3/8" compression
19
0
4" (102mm)
"-20 UNC
1/2”with spacer
1-1/8”without spacer
spacer
14
Dimensions Ultra-Sense Lavatory Faucet, S-6080
20 1/2"
521mm
5 7/64"
130mm
Recognition range and after flow
Recognition range is the distance at which the sensor reacts
by turning on the faucet. After flow is the period that water
continues to flow after the user’s hands are removed from the
recognition range. Both recognition range and after flow are
factory preset for optimal performance.
Battery (Lithium 2CR5 6V)
The Ultra-Sense’s power source is one 6 volt lithium battery
that lasts approximately 5 years (210 cycles/day).
OPERATION
The Ultra Sense lavatory faucet is turned on and off by a
sensor-controlled solenoid valve. Placing your hands within
the recognition range of the sensor opens the solenoid valve
and water starts to flow. When you withdraw your hands, the
faucet turns itself off automatically following a preset after
flow period. Faucets have a temperature adjustment handle
and are equipped with an adjustable handle limit stop. The
faucet is taken out of operation, e.g. for cleaning the lavatory,
by covering sensor with plastic cleaning cover accessory
included with the faucet.
Cleaning
Cleaning of the external faucet surfaces should be carried out
using a neutral, liquid cleaner. Scrubbing or corrosive agents
must not be used and neither should the faucet be cleaned
with a high pressure washer. Keeping the sensor clean assures
faultless operation.
Risk of freezing
When installing the faucet in a place where the temperature
may fall below freezing, the entire system must be drained of
water to prevent bursting in freezing weather.
1. Shut of water supply.■
2. Disconnect all exible hoses.■
3. Drain all parts and hoses of water.■

off
SF-147
SF-152
SF-156
SF-154
SF-155
SF-150A
SF-153
SF-2CR5
SF-158
SF-152
SF-156
SF-162
SF-154
SF-155
SF-151
SF-147
SF-125
SF-186 (2)
SF-159
SF-148 (2)
SF-181 (2)
S-6080-LST
ONLY SF-143(2)
KN-23(2)
SF-142 KN-26(2)
L-36(2)
Cleaning
cover
Parts Assembly Ultra-Sense Lavatory Faucet, S-6080
KN-23 Anchor Bar
KN-26 Spirol Spacer
L-36 Nut
SF-125 Aerator
SF-138 Deck Plate
SF- 140 Gasket
SF-142 Mounting Kit
SF-143 Mounting screws
SF-145 Label
SF-147 Sensor Repair Kit
SF-148 Supply Hoses
SF-150A PilotValve Repair Kit
SF-151 Solenoid
Valve Membrane
SF-152 Housing Screw
SF-153 Handle Plug Button
SF-154 Handle
SF-155 Handle Screw
SF-156 Handle Limit Stop
SF-158 Single Mount Kit
SF-159 Plug
SF-162 Mixer
SF-181 Check strainer assembly
SF-186 Check Strainer Kit
SF-2CR5 6V Lithium Battery
SF-138
Figure 2
off
SF-152
SF-156
SF-154
SF-155
SF-147
Figure 1

TROUBLE SHOOTING CHART
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184
[phone], [phone] ■Fax [phone]
Website: www.symmons.com ■Email: [email protected]
©2007, 2008 Symmons Industries, Inc. Printed in U.S.A. ■ZV-409 ■092909
SERVICE INSTRUCTIONS
Changing the mixer
1. Close the water inlet(s).
2. Remove Housing screw (SF-152).
3. Remove Handle screw (SF-155), handle (SF-154),
handle limit stop (SF-156), housing and mixer
(SF-162).
4. Install new mixer reversing steps above.
Changing solenoid valve
1.Close the water inlet(s).
2.Remove Housing screw (SF-152).
3. Remove Handle screw (SF-155), handle (SF-154),
handle limit stop (SF-156), housing and solenoid valve
(SF-150).
4. Install new solenoid valve reversing steps above.
Cleaning or changing the solenoid valve
membrane
1. Close the water inlet(s).
2. Remove Housing screw (SF-152).
3. Remove Handle screw (SF-155), handle (SF-154),
handle limit stop (SF-156), housing and solenoid valve
membrane (SF-151).
4. Clean the membrane (SF-151) or if necessary replace
with a new one reversing the steps above.
Changing the battery (Lithium 2CR5 6V)
(See figure 1)
A blinking signal light on the sensor indicates that the
battery needs to be changed.
1. Close the water inlet(s).
2. Remove Housing screw (SF-152).
3. Remove Handle screw (SF-155), handle (SF-154),
handle limit stop (SF-156) and housing.
4. Remove battery holder and replace battery as shown
reversing steps above.
Changing the sensor (See figure 2)
Note: Special tool required
1. Close the water inlet(s).
2. Remove Housing screw (SF-152).
3. Remove Handle screw (SF-155), handle (SF-154),
handle limit stop (SF-156) and housing.
4. Remove battery holder, clip, and sensor (SF-147) as
shown and install new sensor reversing steps above.
Problem Cause Solution (Follow service instructions)
Water ow from the outlet does not
stop.
The sensing range is too low or the
solenoid valve is damged.
Solenoid valve membrane is dirty.
Check that the photocell is clean.
Replace solenoid valve.
Clean the solenoid valve mem-
brane.
Water ow is low and weak. Supply stop(s) not fully opened.
The Litter lter(s) or aerator is
clogged.
Open supply stop(s).
Clean the litter lter(s) and aerator.
No water comes out of the faucet. Faucet not recieving water.
The solenoid valve is damaged.
Power failure.
The sensor is covered or damaged.
Battery not installed correctly.
Check the water supply to the
faucet.
Replace solenoid valve.
Clean or replace sensor.
Check battery installation.
Sensor eye is blinking. Ultra-Sense’s visible diagnostic
signal is activated indicating low
battery voltage.
Replace battery Lithium 2CR5 6V.
Temperature can’t be adjusted. Mixer is damaged.
Litter lters are dirty.
Clean or replace the mixer.
Clean the litter lter(s).