Synca JP-970 User manual

our
5002153
JP- 970
Massage Chair
Product Name :

while
while

Power cord clip
Mounting screws
Footrest
Outer cover A Outer cover B Outer cover B
Mounting screws
(2pcs)
Mounting screws for arm
unit. (Longer one x 4pcs)
Mounting screws for outer cover A.
(Shorter one x 4pcs)
Mounting screws for footrest.
(Shorter one x 2pcs)
(L/R)
(L/R) (L/R)

60
192
20
76
76
74
Keep space more than 20cm in the back
so that the chair can recline and install/put
the chair on the horizontal location.
Lift up and move the chair with holding
the handle in the front and back.
Footrest move up when the chair reclines. Keep space
more than 60cm in the front and 20cm in the back before
use.

How to attach the footrest. (Power won't be on unless footrest is installed.)
Make sure to hold the footrest connector
itself and insert.
Insert the connector case not to
crush the air joint hole. It may cause
air leakage.
Insert it not to pinch a cord.
Mounting sound is heard.
Do not attach the hose or cord when they
are twisted.
Do not attach the hose or cord when they
are twisted.
Locate the footrest in front of
the body of the chair.
Insert the footrest connector
firmly until mounting sound is
heard from the connecting point
of connector.
Insert the footrest connector
case into the main body.
Fix the footrest connector case
and main body with mounting
screws for footrest connector.
Connecting point
Hose
Cord
Footrest connector
Air joint hole
Hex wrench
Footrest connector case

Lift up Seat
Fixing
screws
Hex
wrench
Fixing
screws
Mounting
cover
Mounting
cover
Footrest
mounting
part
Attaching
part
The velcro
Insert
Make sure to attach without gap.
Insert the footrest connector
firmly until mounting sound is
heard from the connecting point
of connector.
Lift up mounting cover.
Insert the footrest mounting part
into attaching part.
Make sure to lock them with fixing screws.
Pay attention not to damage the seat by hex
wrench.
Check the footrest mounting part does not
come out from mounting cover. If it is not
attached firmly, footrest falls down and it may
cause injury or failure.
Down the mounting cover and fix them with fixing screws by hex wrench.
(1 pc each on left and right.)
Put the velcro on the back of seat and another one on blindfold cover
together.
How to attach the footrest part (Continuation)

How to attach the footrest part (Continuation)
Power switch is located in the lower part of
main body on left side.
Insert the power plug of power cord into the outlet.
Turn
「ON」
the power switch of main body.
Press button and turn the power on.
Press Ricliningbutton and recline up the backrest.
Turn
「OFF」
the power switch of main body and pull out
the power plug from the outlet.

Remote control
stand
Arm unit
(L)
Figure: back side of arm unit (L).
Dent
Fixing
screws
Rear
side
Front
side
Loosen
Fixing
screws
Insert
Dent
Tighten
Mounting screws
for arm part
(Longer one)
Mounting
screws
Air joint
× 4
(2 pcs each for left
and right side.)
Mounting
part of
arm unit.
Mounting
part of main
body side.
Loosen 2 fixing screws in the back of arm unit a bit.
Insert the remote control stand into the dent of
armrest side and insert the remote stand into
where it's done in the first procedure (1.)
How to attach the remote stand. (It is attachable both left and right side.)
How to attach the arm part. (both left and right side.)
Pay attention not to damage the armrest when
inset the remote control stand.
Tighten the fixing screws and secure the remote
control stand and arm part.
Secure them firmly.
Insert the mounting part of arm unit into the mounting
part of main body side.
Fix the mounting screws by
hex wrench.
If it is not attached firmly, arm part
fall down and it may cause injury or
damage.
Attach the air joint of main body and arm
unit.
Insert them firmly.
If it is not attached firmly, air leakage may happen
and it may cause injury or damage.
Remote control stand may come off and it may cause injury
or damage.

How to attach the outer cover. (Both left and right side.)
Hook and catch the outer cover A with the hooks on the main body.(3 parts)
Slide the outer cover A to the rear
direction while pressing the outer
cover A to the main body.
Attach the outer cover B. Hook the
front side first.
Fix the back side with mounting
screw for outer cover B. Fix the
cord clip together for the side
which remote control stand is
attached.
Fix the mounting screws for outer
cover A by hex wrench. (2 location)
2 hook parts of front side are located inside the
outer cover A.
Make sure if the hook part of front side
are fixed after slide it.
Hook the remote control cord to the cord clip
which is attached with outer cover B.
Place the remote control from the top onto
remote holder.
Check if the cord clip is attached in the same side of
remote control stand.
Screw the fixing screw and decide the
remote holder position. Fix it in the favorite
position.
Pay attention not to tighten too much as it may
cause a break.
Make sure to hook the remote control cord in the cord clip.
If not, it may cause disconnection due to the interference
with main body.
Match the hook part in the rear side and match
the 2 hook part in the front side.
Mounting screws
for outer cover.
(Shorter one)
Hook part
Hook part
Outer cover B
Cord clip
Remote control
holder
Fixing screw
Tighten
Loosen
Cord clip
Mounting screw
for outer cover B.
Mounting
screws
for outer
cover A.
Slide the outer cover
to the rear direction while
pressing the outer cover.