System air CORRIGO User manual

INSTRUCTIONS FOR
WATER COOLER ACTIVATION
CORRIGO CONTROLLER
Basic
FGT010, FGT015, FGT022

2
Contents
1. Search for Admin access.................................................................................................................. 3
2. Search for analog output menu for water cooler ........................................................................... 5
3. Search for type of cooler menu....................................................................................................... 7
4. Electric wiring diagram.................................................................................................................... 8
5. In case that your FGT Basic unit will not have any heater element................................................ 9
5.1 Deactivating frost protection sensor..................................................................................... 10
5.2 Deactivating heating signal (AO) ........................................................................................... 12
5.3 Deactivating heating signal (DO) ........................................................................................... 13
5.4 Change type of heater element............................................................................................. 14

3
1. Search for Admin access
Put yourself on the first screen:
Press DOWN key button to enter the menu:
Press DOWN key button (4x) to access the menu ''Access rights'':
Press RIGHT key button:
Press RIGHT key button:

4
Press the OK button to position yourself on ''Enter password''. Please enter the password ''1111''. For
entering the password press UP key (2x) for value 1. Press RIGHT key for next position and repeat the
process for the password ''1111'':
Press OK button and you will be logged in as ''Admin'':

5
2. Search for analog output menu for water cooler
Press LEFT key (2x) to get to the menu:
Press UP key button to position yourself on the menu ''Configuration'':
Press RIGHT key button:
Press RIGHT key button:
Press DOWN (7x) to get to ''AO'':
Press RIGHT key button:
In the top left corner the menu will show ''AO1'':

6
Press DOWN key for ''AO2'':
Press OK button to change from ''Not used'' to ''Y3 cooling''. To do that you need to press DOWN key
(3x) and OK button (3x):
Now we selected the signal for cooling. We need to select what type of water cooler we have.
After activating the function, you must restart the unit!

7
3. Search for type of cooler menu
When we are still at the top menu shown one-step before. Press LEFT key (2x) for menu
''Inputs/Outputs''
Press DOWN key button (8x) for menu ''Cooling'':
Press RIGHT key button:
Press OK button and then UP key (2x) for ''Water'' and again OK button to confirm:
Configuration for water cooler is completed. Press LEFT (2x):
Press UP key (7x) to return to main screen:

8
4. Electric wiring diagram

9
Use terminal 37, 38 and 39 and corresponding pins G0, G and Y on the valve to connect.
Connect G0 to terminal 37, G to terminal 38 and Y to terminal 39.
5. In case that your FGT Basic unit will not have any heater element
If FGT Basic AHU will be only for cooling request without any heater element, it is necessary to
deactivate frost protection sensor, signal for relay activate and type of heating element!
Put yourself on the first screen:
Press DOWN key button to enter the menu:
Press DOWN key button (4x) to access the menu ''Access rights'':
Press RIGHT key button:

10
Press RIGHT key button:
Press the OK button to position yourself on ''Enter password''. Please enter the password ''1111''. For
entering the password Press UP key (2x) for value 1. Press RIGHT key for next position and repeat the
process for the password ''1111'':
Press OK button and you will be logged in as ''Admin'':
5.1 Deactivating frost protection sensor
Press LEFT key button (2x) to get to the menu:
Press UP key button to position yourself on the menu ''Configuration'':
Press RIGHT key button:

11
Press RIGHT key button:
Press DOWN key button (5x) to put yourself to menu ''UI exp3'':
Press RIGHT key button:
On the top left of the screen you should have ''UI1'' selected:
Press DOWN key for ''UI2'':
We need to change the ''Frost prot t'' to ''Not used''
Press OK button and then UP key (11x) and again OK button (2x):

12
5.2 Deactivating heating signal (AO)
Press LEFT key button:
Press DOWN key button (2x):
Press RIGHT key button:
Press OK to change value from ‘’Y1 heating’’ to ‘’ Not used’’
Press UP key button:
Press OK button (3x)

13
5.3 Deactivating heating signal (DO)
Press LEFT key button:
Press DOWN key for menu ''DO'':
Press RIGHT key button:
We need to change from ''P1 heating'' to ''Not used''.
Press OK button and then UP key (5x):
Press OK button (2x).

14
5.4 Change type of heater element
We need to set the type of the heater (in our case there is no heater element).
When we are still at the top menu shown one-step before. Press LEFT key (2x) for menu
''Inputs/Outputs'':
Press DOWN key (6x) for menu ''Heating'':
Press RIGHT key button:
Now press OK button and UP key button (2x). Menu should be displayed ''Not connected'' and press
OK button.
Configuration for Electric heater is complete. Press LEFT (2x):
Press UP key button (7x) to return to main screen: