System Build 7446059COM User manual

7446059COM
Tall Storage Cabinet
- Unit can tip over causing severe injury or death.
- Anchor unit to stud in wall (if instructed to).
- Do Not allow children to climb on unit.
- Put heavy items on lower shelves or drawers.
B347446059COMT0
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
WARNING
For the latest information on SystemBuild products
follow us at Ameriwood Home
Tube
You
Date of Purchase ___ / ___ / ___
Lot Number:
Do Not Return This Product!
Contact our customer service team for help first.
Call: 1-866-452-4081 (toll free)
Monday-Friday 9am - 5pm CST
Visit: www.systembuild.com
Assembly Difficulty Meter
Easy Tough

Contact Us!
Helpful Hints
2
systembuild.com
Do NOT return this product!
Contact our friendly customer service team first for help.
Call us!
1-866-452-4081
Monday-Friday
9am - 5pm CST
Visit systembuild.com to view the
limited warranty valid in the U.S. and Canada.
Assembly Tips
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with a R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- Use all the nails provided for the back panel and spread them out equally.
- Back panel must be used to make sure your unit is sturdy.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
Tube
You
Tube
You
PEOPLE NEEDED FOR ASSEMBLY: 1-2
ESTIMATED ASSEMBLY TIME: 1 HOUR

3
systembuild.com
Before You Start
P
Quick
Tip
Assembly
P
P
P
Tube
You
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.
P

4
systembuild.com
Board Identification
Not actual size
Tube
You
Left Panel
37446315010
This piece is of paperboard
construction. It is not made
from wood, but is required
for the assembly of your unit.
Right Panel
37446315020
Top
37446315030
Bottom
37446315040
Fixed Shelf
37446316050
(2)
Adjustable Shelves
37446316060
Left Door
37446315070
Right Door
37446315080
Back Panel
K74465600
G
I
B
ACDE
F
H

5
systembuild.com
Board Identification
This piece is of paperboard
construction. It is not made
from wood, but is required
for the assembly of your unit.
Not actual size
A
B
C
D
I
E
F
F
G
H
Tube
You

6
systembuild.com
Part List
Actual Size
Tube
You
Not Actual Size
(x12)
#A13410
1-3/4" flat head
(x8)
#A12100
7/16" pan head
(x40)
#A21110
nail
(x8)
#A80250
shelf support
(x2)
#A89020
bumper
(x4)
#A23700
rubber cap
(x2)
#A11120
1/2" pan head
(x2)
#A11195
5/8" pan head
(x2)
#A11210
3/4" pan head
(x4)
#A24015
screw cap
(x16)
#A11600
1-1/4" flat head
(x2)
#A92520
base plate
(x1)
#A55015
lock
(x1)
#A55410
latch

7
systembuild.com
Not Actual Size
(x2)
#A52995
handle
(x6)
#A65615
hinge
(x4)
#A43600
adjustable leg
(x4)
#A43610
leg mount
(x1)
#A84050
safety bracket kit
Separate hinge by loosening
screw as shown.
Tube
You

8
systembuild.com
STEP1
Tube
You
(x6)
#A65615
Separate hinge by loosening
screw as shown.
A
B

9
systembuild.com
STEP2
Tube
You
(x4)
#A13410
A
B
E
Finished edges are facing upwards.

10
systembuild.com
STEP3
Finished edges are facing upwards.
(x8)
#A13410
(x2)
#A11195
5/8" pan head
(x2)
#A89020
bumper
(x1)
#A84050
safety bracket kit
Tube
You
C
C
A
B
E
D
C

11
systembuild.com
STEP4
Tube
You
(x40)
#A21110
IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT
AND MUST BE INSTALLED PROPERLY.
* raw edges are shaded
Attached the back panel as shown nailing straight into the raw edges.
Assure that the unit is square.
Distance from corner to corner must be equal as shown.
I
Place the unit on its front as shown.

12
systembuild.com
STEP5
(x16)
#A11600
(x4)
#A24015
(x4)
#A43600
(x4)
#A43610
Tap screw caps onto the screws.
Attach the leg mounts to the bottom (D).
Press the adjustable leg sleeve into the
leg mounts as shown.
Thread the adjustable leg onto the sleeve.
D
Tube
You
sleeve
leg mount
adjustable leg

13
systembuild.com
STEP6
stud
wallboard
hole
(x1)
#A84050
Stand the unit upright and place against the wall.
Fasten the wall anchor to the wall using option 1 or 2.
Option 1: Securely screw into solid area of the wall as shown.
Option 2: Drill a 3/16" diameter hole (5mm) in the wallboard.
Tap the wall anchor into the hole until it is flush.
Fasten the wall bracket to the wall anchor with the screw.
Tube
You
option 1
option 2
C

14
systembuild.com
STEP7
G
G
H
H
(x8)
#A12100
(x2)
#A11210
(x2)
#A11120
(x1)
#A55410
(x6)
#A65615
(x1)
#A55015
(x2)
#A92520
Attach base plates to each door using the 7/16" screws.
Turn doors over and use two 3/4" screws to attach the latch to the Left
Door (G).
Attach the lock to the Right Door (H) using the 1/2" screws.
Fasten the hinges to each door as shown.
Tube
You

15
systembuild.com
STEP8
WARNING:
Before continuing with the assembly of your unit,
make sure that the cabinet is properly and securely
fastened to the wall.
If not, YOUR UNIT MAY TIP, causing possible bodily
injury and also damage to your unit.
(x8)
#A80250
F
F
Tube
You

16
systembuild.com
STEP9
(x2)
#A52995
To lock the doors:
1. Close the left door (G) first. Extend
the barrel of the latch down into the
hole in the bottom shelf.
2. Close the right door (H). Insert
the key into the lock and turn.
This will position the lock bar
behind the left door. Remove the
key.
(x4)
#A23700
Tube
You

17
systembuild.com
STEP10
Loosen screw C
Adjust door.
Tighten screw C
*side view
Loosen screw C
Turn screw B to
move door.
Tighten screw C
Loosen screw A
Adjust door.
Tighten screw A
A
BC
Tube
You

18
systembuild.com
Tube
You
Maximum Loads
Warning: Risk of injury to persons - do not place a television on this furniture. This furniture is
not approved for use with a television.
Certificate of Conformity
1. This certificate applies to the Dorel Home Furnishings, Inc. product identified by this instruction manual.
2. This certificate applies to compliance of this product with the CPSC Ban on Lead-Containing Paint (16 CFR 1303).
3. This product is distributed by: Dorel Home Furnishings, Inc.
410 East First Street South
Wright City, MO 63390
636-745-3351
4. Site of Manufacture: Tiffin OH
5. See front page of instruction manual for date of manufacture.
30 lbs
13.6 kg
This unit has been designed to support the maximum loads shown. Exceeding these load limits
could cause sagging, instability, product collapse, and/or serious injury.
0 lbs
0 kg

19
systembuild.com
Register your product to receive the following:
* New trend details - sneak peek on what's new
* Surveys - have a voice within our community
* Exclusive deals and discount codes
* Quick and easy replacement part service
To register your product, visit systembuild.com
Visit your local retailer's website, rate your purchased
product and leave us some feedback!
We would like to extend a big "Thank You" to all of
our customers for taking the time to assemble this
Systembuild product, and to give us your valuable
feedback.
Tube
You

20
systembuild.com
Tube
You
Cubierta Delantera
Este libro de instrucciones contiene información IMPORTANTE de seguridad. Por favor lea y manténgalo
para referencia en el futuro.
No Regrese este producto! Comuniquese con nuestro amistoso equipo de servicio al cliente para obtener
ayuda.
Llamenos al: 1-866-452-4081 (Gratis) Lunes - Viernes 9am - 5pm CST
Visitar: www.systembuild.com
PRECAUCION
Este mueble puede volcarse y causar graves heridas y/o muerte.
Anclar el mueble a un poste de madera en la pared (si esto se requiere).
No Permita que los niños monten el mueble.
Mantenga los artículos más pesados en los cajones de abajo.
Consejos Útiles (página 2)
- Abra su artículo en el área donde usted planea utilizarlo para evitar levantar y moverlo menos
- Identificar, ordenar y contar las piezas antes de intentar ensamblar
- Las clavijas de compresión se golpean con un martillo
- Las diapositivas están marcadas con una R (derecha) y L (izquierda) para la colocación correcta
- Asegúrese de que siempre este el punto locaizado en la parte superior de bloqueador de leva
este volteadohacia borde exterior
- Utilizar todos los clavos para el panel de atras y distribuirlos por igual
- El panel de atras debe utilizarse para asegurarse de que la unidad quede fija y firme
- No use quimicas fuertes ni limpiadores abrasivos en este articulo
- Nunca empuje, tire ni arrastre los muebles
Antes de Que Empieces (página 3)
-Lea cuidadosamente cada paso y siga el orden correcto
-Separar y contar todas sus piezas y hardware
-Dése suficiente espacio para el proceso de ensamble
-Tenga las siguientes herramientas: destornillador de cabeza plana, #2 cabeza Phillips
Destornillador y martillo
-Precaución: Si usa un taladro electrónico o un destornillador eléctrico para atornillar, por favor asegúrese
que deje de atornillar cuando el tonillos este apretado. Fallar hacer esto puede causar barrer el tornillo.
Sistema de fijar el bloqueo de leva (página 3)
Esta sistema de fijar el bloqueo de leva sera usado en todo el proceso ensamble.
Página 4
Esta pieza es de cartón. No está hecha de madera; sin embargo, es necesaria para el montaje de su unidad.
Español