System Sensor M500FP User manual

0
1
2
3
4
9
8
7
6
5
0
TENS
ONES ADDRESS
LOOP
9
8
7
6
5
4
3
21
0
9
8
7
6
5
4
3
21
D500-39-00 I56-1392-005
M500FP Firephone Control Module
INSTALLATION AND MAINTENANCE INSTRUCTIONS
Before Installing
This information is included as a quick reference installation
guide. If the modules will be installed in an existing operational
system, inform the operator and local authority that the system
will be temporarily out of service. Disconnect power to the control
panel before installing the modules.
NOTICE: This manual should be left with the owner/user of this
equipment.
General Description
M500FP Firephone Control Modules are intended for use in in-
telligent, two-wire systems, where the individual address of each
module is selected using the built-in rotary switches. This module
is used to connect a remote firefighter telephone to a centralized
telephone console. A ringing sound is provided at each off-hook
handset until it is connected to the console. Wiring to individual
telephone jacks and handsets is supervised, and status is re-
ported to the panel as NORMAL, TROUBLE, or TELEPHONE. The
M500FP has two pairs of output termination points available for
fault-tolerant wiring, and includes a panel-controlled LED indica-
tor.
Compatibility Requirements
T
o ensure proper operation, this module shall be connected to
Listed compatible system control panels only.
Mounting
This module mounts directly to 4″square electrical boxes (see
Figure 2A). The box must have a minimum depth of 21
/8″. Flush
mounted electrical boxes (SMB500) are available.
Wiring
NOTE: All wiring must conform to applicable local codes, ordi-
nances and regulations. When using control modules in
nonpower limited applications, the CB500 Module Barrier
must be used to meet UL requirements for the separation
of power-limited and nonpower-limited terminals and
wiring. The barrier must be inserted into a 4″ × 4″ × 21
/8″
junction box, and the control module must be placed into
the barrier and attached to the junction box (Figure 2A).
The power-limited wiring must be placed into the isolated
quadrant of the module barrier (Figure 2B).
Figure 1. Controls
and Indicators
Figure 2A. Module mounting with barrier:
C0219-01
Figure 2B:
C0217-01
C0218-01
Specifications
Normal Operating Voltage: 15 to 32 VDC
Maximum Current Draw: 7.5mA (LED on).
Average Operating Current: 2.4mA (LED flashing).
Handset Offhook Resistance: 400 to 1,500 Ohms
External Supply Voltage (between Terminals T3 and T4)
Regulated 24VDC
Temperature Range: 32˚F to 120˚F (0˚C to 49˚C)
Humidity: 10% to 93% Non-condensing
Dimensions: 41 /2″H x 4″W x 1
1
/4″D (Mounts to a 4″square by 21 /8″deep box.)
Accessories: SMB500 Electrical Box; CB500 Barrier
1. Install module wiring in accordance with the job drawings and
appropriate wiring diagrams (Figures 3-4).
2. Set the address on the module per job drawings.
3. Secure module to electrical box (supplied by installer), as
shown in Figure 2A.
3825 Ohio Avenue, St. Charles, Illinois 60174
1-800-SENSOR2, FAX: [phone]
www.systemsensor.com
9
8
7
6
54
3
2
1
0
0
1
2
3
4
56789
TENS
ONES
ADDRESS
LOOP
10
78
6
5
4
3
2
9
ISOLATED
QUADRANT
0
1
2
3
4
9
8
7
6
5
0
TENS
ONES ADDRESS
LOOP
9
8
7
6
5
4
3
21
0
9
8
7
6
5
4
3
21
I56-1392-005
firealarmresources.com

FROM PANEL OR
(+)
(-)
TO NEXT
(+)
(-)
DEVICE
(+)
(-)
(-)
(+)
3.9K EOL
RESISTOR
A2143-10
MODULE POLARITIES ARE
SHOWN IN ALARM
32 VDC MAX.
IS RECOMMENDED
BRANCH CIRCUITS
BREAK ALL WIRE TO ENSURE
SUPERVISION OF CONNECTIONS.
DO NOT LOOP WIRE AROUND TERMINALS.
(-)
(+)
TWISTED PAIR
SIGNAL LINE CIRCUIT (SLC)
PREVIOUS DEVICE
(-)
(+)
TELEPHONE CONSOLE
24 VOLTS DC POWER LIMITED
9
8
7
6
54
3
2
1
0
0
1
2
3
456789
TENS
ONES
ADDRESS
LOOP
0
78
6
5
4
3
21
9
TELEPHONE CONSOLE MUST
PROVIDE ITS OWN
WIRING SUPERVISION
ALL WIRING SHOWN IS SUPERVISED
AND POWER LIMITED CONNECT MODULES TO LISTED COMPATIBLE
CONTROL PANELS ONLY
FROM PANEL OR
(+)
(-)
TO NEXT
(+)
(-)
DEVICE
(+)
(-)
(-)
(+)
3.9K EOL
RESISTOR
A2143-10
MODULE POLARITIES ARE
SHOWN IN ALARM
CONNECT MODULES TO LISTED COMPATIBLE
32 VDC MAX.
IS RECOMMENDED
BRANCH CIRCUITS
BREAK ALL WIRE TO ENSURE
SUPERVISION OF CONNECTIONS.
DO NOT LOOP WIRE AROUND TERMINALS.
ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
(-)
(+)
TWISTED PAIR
NOTIFIER CONTROL PANELS ONLY
SIGNAL LINE CIRCUIT (SLC)
PREVIOUS DEVICE
(-)
(+)
TELEPHONE CONSOLE
24 VOLTS DC POWER LIMITED
9
8
7
6
54
3
2
1
0
0
1
2
3
456789
TENS
ONES
ADDRESS
LOOP
0
78
6
5
4
3
21
9
TELEPHONE CONSOLE MUST
PROVIDE ITS OWN
WIRING SUPERVISION
D500-39-00 2 I56-1392-005
©System Sensor 2006
WARNING
All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state during
shipping. To ensure that the switch contacts are in their correct state, modules must be made to communicate with the panel before
connecting circuits controlled by the module.
Figure 3. Typical circuit configuration, NFPA Style Y, Class B style wiring:
Figure 4. Typical fault tolerant circuit configuration, NFPA Style Z, Class A style wiring:
Relay Contact Rating: 24 VDC, 3 Amperes Maximum
C0220-02
C0221-02
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inter-
ference to radio communications. Operation is subject to the following two conditions: (1) This device may not cause harmful radiation,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
firealarmresources.com