Tadano GR-1000XL-2 User manual

Note : Dimension is with boom angle at -0.8 degree.
Feet Meters
Turning radius
4 wheel steer 21' 11-3/4" 6.7
2 wheel steer 39' 1/2" 11.9
Tail swing of counterweight 13' 8-15/16" 4.19
Specifications are subject to change without notice.
provisional
GENERAL DIMENSIONS
(29.5 X 25 Tires)
GR-1000XL-2
100 Ton Capacity (90.7 Metric Tons)
HYDRAULIC ROUGH TERRAIN CRANE
DIMENSIONS
１

CRANE SPECIFICATIONS
BOOM
WIRE ROPE
- Non-rotating 3/4"(19mm) P
・
S(19)+39xP
・
7 Min.
Four section full power synchronized telescoping boom,
Breaking Strength 72,765lbs
39.4'~154.2' (12.0m~47.0m), of round box construction
with five sheaves, 17-5/16" (0.44m) root diameter, at boom head.
HOOK BLOCKS
The synchronization system consists of two telescope cylinders,
100+(90.7 metric ton)-8sheaves with swivel hook and safety latch,for
an extension cable and retraction cable. Hydraulic cylinder fitted
3/4"(19mm) wire rope (OPTIONAL).
with holding valve. Two easily removable wire rope guards, rope
7.3 ton (6.6 metric ton) - Weighted hook with swivel and
dead end provided on both sides of boom head. Boom telescope
safety latch, for 3/4"(19mm) wire rope.
sections are supported by wear pads both vertically and horizontally.
Extension speed 114.8 in 128 seconds.
HYDRAULIC SYSTEM
BOOM ELEVATION
- By a double acting hydraulic cylinder
with holding valve. Elevation -1.5
o
~80.5
o
, combination controls for PUMPS - Two variable piston pumps for crane functions.
hand or foot operation. Boom angle indicator.
Tandem gear pump for steering, swing and optional equipment.
Automatic speed reduction and soft stop function.
Powered by carrier engine. Pump disconnect for crane is
Boom raising speed 20
o
to 60
o
in 46 sec.
engaged/ disengaged by rotary switch from operator's cab.
JIB - two stage bi-fold lattice type, 3.5
o
, 25
o
or 45
o
offset (tilt type). CONTROL VALVES - Multiple valves actuated by pilot
Single sheave, 15-5/8"(0.396m) root diameter, at the head of both
pressure with integral pressure relief valves.
jib sections. Stored alongside base boom section. Jib length is
33.2' (10.1m) or 58.1' (17.7m). Assistant cylinders for mounting
RESERVOIR
- 224 gallon (840 lit.) capacity. External sight
and stowing, controlled at right side of superstructure.
level gauge.
Self stowing jib mounting pins.
FILTRATION
- BETA10=10 return filter, full flow with bypass
AUXILIARY LIFTING SHEAVE
(SINGLE TOP)
protection, located inside of hydraulic reservoir. Accessible for
Single sheave, 15-5/8"(0.396m) root diameter. Mounted to main
easy replacement.
boom head for single line work (stowable).
OIL COOLER
- Air cooled fan type.
ANTI-TWO BLOCK
- Pendant type over-winding cut out
device with audio-visual (FAILURE lamp/BUZZER) warning system.
CAB AND CONTROLS
SWING
Hydraulic axial piston motor through planetary swing
Both crane and drive operations can be performed from one
speed reducer. Continuous 360
o
full circle swing on ball bearing
cab mounted on rotating superstructure.
turn table at 1.5rpm. Equipped with manually locked/released
swing brake. A 360
o
positive swing lock for pick and carry
Left side, 1 man type, steel construction with sliding door
and travel modes, manually engaged in cab. Twin swing
access and safety glass windows opening at side. Door
system: Free swing or lock swing controlled by selector switch
window is powered control. Windshield glass window and roof
on front console.
glass window are shatter-resistant. Tilt-telescoping steering
wheel. Adjustable control lever stands for swing, boom hoist,
HOIST
boom telescoping, auxiliary hoist and main hoist. Control lever
stands can change neutral positions and tilt for easy access to
MAIN HOIST
- Variable speed type with grooved drum driven
cab. Engine throttle knob. Foot operated controls: boom hoist,
by hydraulic axial piston motor through winch speed reducer.
boom telescoping, service brake and engine throttle. Hot water
Power load lowering and raising. Equipped with automatic
cab heater and air conditioning.
brake (neutral brake) and counterbalance valve. Controlled
independently of auxiliary hoist. Equipped with cable follower
Dash-mounted engine start/stop, monitor lamps, cigarette
and drum rotation indicator.
lighter, drive selector switch, parking brake switch, steering
mode select switch, power window switch, pump engaged/
DRUM
- Grooved 14-1/4"(0.362m) root diameter x 23-5/8"
disengaged switch, swing brake switch, telescoping/auxiliary
(0.6m) wide. Wire rope: 820' of 3/4"diameter rope (250m of
winch select switch, outrigger controls, main winch/auxiliary
19mm). Drum capacity: 997' (304m) 7 layers. Maximum single line
winch selector switch, swing stop cancel switch, slow elevation
pull:1st layer 20,040 lbs (9,090kg).Maximam permissible line pull :
stop cancel switch, free swing / lock swing selector switch and
14,500 lbs (6,600kg).
ashtray.
AUXILIARY HOIST
- Variable speed type with grooved drum
Instruments - Torque converter oil temperature, engine water
driven by hydraulic axial piston motor through winch speed
temperature, air pressure, fuel, speedometer, tachometer and
reducer. Power load lowering and raising. Equipped with
hour meter. Hydraulic oil pressure is monitored and displayed
automatic brake (neutral brake) and counterbalance valve.
on the AML-C display panel.
Controlled independently of main hoist. Equipped with cable
follower and drum rotation indicator.
DRUM
- Grooved 14-1/4"(0.362m) root diameter x 23-5/8"
(0.6m) wide. Wire rope: 456' of 3/4"diameter rope (139m of
19mm). Drum capacity: 997' (304m) 7 layers. Maximum single line
pull:1st layer 20,040 lbs (9,090kg).Maximam permissible line pull :
14,500 lbs (6,600kg).
2

Tadano electronic LOAD MOMENT INDICATOR system
TADANO AML-C monitors outrigger extended length and
(AML-C) including:
automatically programs the corresponding "RATED LIFTING
h
Control lever lockout function with audible and visual
CAPACITIES" table
pre-warning
h
Boom position indicator
Operator's right hand console includes transmission gear
h
Outrigger state indicator
selector and sight level bubble. Upper console includes
h
Boom angle / boom length / jib offset angle / load
working light switch, roof washer and wiper switch
radius / rated lifting capacities / actual loads read out
emergency outrigger set up key switch,
h
Ratio of actual load moment to rated load moment
drum indicator switch, jib equipped/removed select switch,
indication
boom emergency telescoping switch (2nd and 3rd
･
top)
h
Automatic Speed Reduction and Soft Stop function
and air conditioning control switch. Swing lock lever.
on boom elevation and swing
h
Working condition register switch
NOTE:
Each crane motion speed is based on unladen
h
Load radius / boom angle / tip height / swing range
conditions.
preset function
h
External warning lamp
h
Tare function
TADANO AML-L monitors outrigger extended length and
automatically programs the corresponding "RATED LIFTING
CAPACITIES" table.
SUSPENSION
- Front: Rigid mounted to frame. Rear: Pivot
mounted with hydraulic lockout device.
CARRIER SPECIFICATIONS
BRAKE SYSTEMS
- Service: Air over hydraulic disc brakes on
TYPE
- Rear engine, left hand steering, driving axle 2-way
all 4 wheels. Parking/Emergency: Spring applied-air released
selected type by manual switch, 4x2 front drive, 4x4 front and
brake acting on input shaft of front axle. Auxiliary: Electro-
rear drive.
pneumatic operated exhaust brake.
FRAME
- High tensile steel, all welded mono-box construction.
TIRES
- 29.5-25 34PR(OR)
TRANSMISSION
- Electronically controlled full automatic
OUTRIGGERS
- Four hydraulic, beam and jack outriggers.
transmission. Torque converter driving full powershift with
Vertical jack cylinders equipped with integral holding valve. Each
driving axle selector. 6 forward and 2 reverse speeds, constant
outrigger beam and jack is controlled independently from cab.
mesh.
Beams extend to 23' 11-3/8" (7.3 m) center-line and retract to
3 speeds - high range - 2 wheel drive; 4 wheel drive
within 10' 10-1/2" (3.315 m) overall width with floats. Outrigger
3 speeds - low range - 4 wheel drive
jack floats are attached thus eliminating the need of manually
attaching and detaching them. Controls and sight bubble located
TRAVEL SPEED
- 23 mph (37 km/h)
in superstructure cab. Four outrigger extension lengths are
provided with corresponding "RATED LIFTING CAPACITIES" for
AXLE
- Front: Full floating type, steering and driving axle with
crane duty in confined areas.
planetary reduction. Rear: Fullfloating type, steering and driving
Min. Extension
8' 10-5/16"(2.7m) center to center
axle with planetary reduction and non-spin rear differential.
Mid. Extension
18' 1/2"(5.5m) center to center
Mid. Extension
21' 11-3/4"(6.7m) center to center
STEERING
- Hydraulic power steering controlled by steering
Max. Extension
23' 11-3/8"(7.3) center to center
wheel. Four steering modes available: 2 wheel front, 2 wheel
Float size(Diameter)
1' 11- 5/8" (0.6m)
rear, 4 wheel coordinated and 4 wheel crab .
ENGINE
Model
Mitsubishi 6M60-TLA3B
Radiator
Fin and tube core, thermostat controlled
Type
Direct injection diesel
Fan, in.(mm)
Suction type, 6-blade, 23.6 (600) dia.
No. of cylinders
6
Starting
24 volt
Combustion
4 cycle, turbo charged and after cooled
Charging
24 volt system, negative ground
BoreXStroke, in.(mm)
4.646 X 4.528 (118X115)
Battery
2-120 amp. Hour
Displacement, cu. in (liters)
460 (7.54)
Compressor, air, CFM(l /min)
29 CFM (830) at 2,600rpm
Air inlet heater
24 volt preheat
Horsepower (kW)
Gross 267 (200) at 2,600rpm
Air cleaner
Dry type, replaceable element
Torque, Max. ft-lb (kgm)
579 (80) at 1,400rpm
Oil filter
Full flow with replaceable element
Capacity, gal.(liters)
Fuel filter
Full flow with replaceable element
Cooling water
3.4 (13)
Fuel tank, gal.(liters)
79.2 (300), right side of carrier
Lubrication
3.4 ~ 4.0 (13 ~ 15)
Cooling Liquid pressurized, recirculating by-pass Fuel 79.2 (300)
3

-
Five section full power partially synchronized boom
-
Independently controlled outriggers
36.1'~141.1' (11.0 m~43.0 m)
-
Four outrigger extension positions
-
33.1' or 58.1' (10.1 m or 17.7 m) bi-fold lattice jib (tilt type)
-
Self-storing outrigger pads
with 3.5
o
, 25
o
or 45
o
pinned offsets and self storing pins.
-
Outrigger hose protection
-
Auxiliary lifting sheave (single top) stowable
-
Mitsubishi 6M60-TLA3B turbo charged after cooled engine
-
Variable speed main hoist with grooved drum, cable follower
(267HP) with exhaust brake
and 797' of 3/4" cable.
-
Electronic controlled automatic transmission driven by torque
-
Variable speed auxiliary hoist with grooved drum, cable
converter
follower and 436' of 3/4" cable.
-
4 X 4 X 4 drive/steer
-
Drum rotation indicator (thumper type) main and auxiliary hoist
-
Non-spin rear differential
-
Anti-Two block device (overwind cutout)
-
Automatic rear axle oscillation lockout system
-
Boom angle indicator
-
29.5-25 22PR (OR) tires or 29.5-25 28PR (OR) tires
-
Tadano electronic load moment indicator system (AML-C)
-
Disc brakes
-
Outrigger extension length detector
-
Fenders
-
Electronic crane monitoring system
-
Air dryer
-
Tadano twin swing system and 360
o
positive swing lock
-
Water separator with filter(high filtration)
-
Self centering finger control levers with pilot control
-
Engine over-run alarm
-
Control pedals for boom hoist and boom telescoping
-
Back-up alarm
-
3 way adjustable cloth seat with armrests, high back
-
Low oil pressure/high water temp. warning device (visual)
and seat belt
-
Rear steer centering light
-
Tilt-telescoping steering wheel
-
Air cleaner dust indicator
-
Tinted safety glass and sun visor
-
Full instrumentation package
-
Front windshield wiper and washer
-
Complete highway light package
-
Roof window wiper and washer
-
Work lights
-
Power window (cab door )
-
Tool storage compartment
-
Rear view mirrors (right and left side)
-
Tire inflation kit
-
Mirror for main and auxiliary hoists
-
24 volt electric system
-
Cigarette lighter and ashtray
-
6.2 ton (5.6 metric ton) hook with swivel
-
Cab floor mat
-
Towing hooks-Front and rear
-
Pump disconnect in operator's cab
-
Lifting eyes
-
Hydraulic oil cooler
-
Hook block tie down (front bumper)
-
Hot water cab heater and air conditioner
-
Weighted hook storage compartment
-
Telecommunications terminal (HELLO-NET Owner’s Site)
-
Fuel consumption monitor and economy mode
-
Positive control
-
Halogen head lamp
-
Quick reeving type bi-fold jib
-
2-speedhoist
-
100 ton (90.7 metric ton) - 7 sheave with swivel hook and
safety latch for 3/4"(19mm) wire rope
-
Propane heater (less tank)
-
Spot light
LINE SPEEDS AND PULLS
DRUM WIRE ROPE CAPACITIES
F.P.M
m/min
F.P.M
m/min
Lbs.
kgf
Lbs.
kgf
Feet
Meters
Feet
Meters
278
84
387
118
20,040
9,090
14,370
6,520
112.2
34.2
112.2
34.2
302
92
421
128
18,150
8,230
12,780
5,800
122.3
37.3
234.5
71.5
327
99
456
139
16,580
7,520
11,880
5,390
132.2
40.3
366.8
111.8
352
107
491
149
15,250
6,920
10,930
4,960
142.3
43.4
509.1
155.2
377
115
526
160
14,130
6,410
10,140
4,600
152.2
46.4
661.4
201.6
402
122
560
170
13,160
5,970
9,430
4,280
162.4
49.5
823.8
251.1
427 130 595 181 12,320 5,590 8,840 4,010 172.5 52.6 996.4 303.7
1
Line speeds based only on hook block, not loaded.
DRUM DIMENSIONS
2
Developed by machinery with each layer of wire rope, but not based
Inch
mm
on rope strength or other limitation in machinery or equipment.
Root diameter
14-1/4"
362
3
Seventh layer of wire rope are not recommended
Length
23-5/8"
600
for hoisting operations.
Flange diameter
25-7/8"
657
6
HOISTING PERFORMANCE
7
4
7th3
4th
Low High Low
1
5
Wire
rope
layer
2nd
Line pulls Available
2
5th
2
3
Layer
6th
Line speeds1
3rd
STANDARD EQUIPMENT
Main or auxiliary hoist - 14'-1/4" (0.362m) drum
1st
High
OPTIONAL EQUIPMENT
Main and auxiliary drum grooved lagging
3/4" (19mm) wire rope
Rope per layer Total wire rope
4

GR-1000XL WORKING RANGE CHART
5

GR-1000XL WORKING RANGE CHART
6

A
B
C
(12m)
C
(16.38m)
C
C
C
C
C
C
C
C
C
C
C
C
C
(47m)
8 200000 102700
10 180000 102700 90200 40100
12 157900 102700 90200 40100
15 132300 102700 89900 40100 42500 35500
20 99700 99100 76100 40100 42500 35500 40100 33300 35500 32200
25
76900
76200
65600
40100
42500
35500
40100
33300
35500
32200
33300
28700
30
50700
57700
56700
40100
42500
35500
40100
33300
35500
30200
33300
26300
26700
24300
35
42800
41800
40100
42500
35500
39500
31600
35100
27300
30900
24000
26700
24100
20900
40
33100
32100
36400
34100
35500
34000
29300
32000
24900
28400
22000
25300
22300
20900
45 26200 25400 31100 27300 31800 28300 26500 28000 22900 26100 20200 23500 20700 20700
50
20400
25900
22200
26600
23200
24100
24000
21300
22900
18700
21800
19300
19400
55
16600
21900
18400
22600
19300
22200
20100
19600
20100
17400
19600
18000
18100
60
13600
18700
15300
19400
16200
19700
17000
18200
17300
16100
17400
16800
16800
65
12700
16800
13700
17100
14400
16600
14800
15000
15300
15800
15200
70
10600
14600
11600
15000
12300
15200
12700
13800
13200
14300
13400
75 8900 12900 9800 13200 10600 13400 10900 12700 11400 12500 11700
80
8300
11600
9100
11900
9500
11700
9900
11000
10200
85 7100 10300 7800 10500 8200 10800 8600 9700 8900
90 6600 9400 7000 9600 7500 8600 7700
95 5600 8400 6000 8600 6500 7600 6700
100 4800 7500 5200 7700 5600 6700 5900
105 4400 6900 4800 5900 5100
110 3700 6200 4100 5200 4300
115 3100 5600 3500 4500 3700
120 2900 4000 3200
125 2400 3500 2600
130 2000 3100 2200
135 1800
140
D
Telescopin
g mode
2nd boom
3rd boom
4th boom
Top boom
A
C
B
(12m)
B
(16.38m)
B
(20.75m)
B
(20.75m)
B
(25.13m)
B
(25.13m)
B
(29.5m)
B
(29.5m)
B
(33.88m)
B
(33.88m)
B
(38.25m)
B
(38.25m)
B
(42.63m)
B
(42.63m)
B
(47m)
0
o
Telescopin
g mode
A
:Boom length in feet
B
:Load radius in feet
C
:Loaded boom angle (deg.)
D
:Minimum boom angle (deg.) for indicated length (no load)
NOTE: The lifting capacity data stored in The LOAD MOMENT INDICATOR(AML-l) in based on The standard number
of part line listend in the chart.
Standard number of part line for outrigger operation should be according to the following table.
Boom length in feet
(meters)
Number of part line
100
100
139.8'
II
125.5' 139.8'
I
II
50
100
139.8'(42.63m)
100
I
154.2'
111.1'(33.88m) 125.5'(38.25m) 154.2'
0
83
83 83
Telescoping conditions (
％）
I
96.8'(29.5m)82.4'(25.13m)
39.4' 53.7' 68.1' 68.1' 82.4' 82.4' 96.8' 96.8'
39.4' 53.7' 68.1'(20.75m)
111.1'
83 100
0 0 0
125.5'
I, II I I II I II I II
100
II
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS FULLY EXTENDED
23' 11-1/2"(7.3m) SPREAD 360
o
ROTATION
I, III II I
111.1'
II I II
100
66
33 16 1006650 83
100
0 0 0 33 16 50 33 10050
100
0 0 0 33 16 50 33 83100
I, II
0 50 100 0 100 0 100
I II
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 11-1/2"(7.3m) SPREAD
360
o
ROTATION
66
I, II I I III
0
Telescoping mode 2
66
II
100
50
0
66
50 33 66
Telescoping mode 1
39.4'
(12m)
Boom length in feet
(meters)
Single top
jib
1
53.7' to 68.1'
(16.38m to 20.75m)
16Number of part line
82.4' to 154.2'
8 4
(25.13m to 47m)
39.4'
(12m)
1416
Single top
(20.75m to 47m)
jib
68.1' to 154.2'
7

3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 10,800 10,800 9,400 80° 6,800 6,300 5,100
79° 10,800 10,400 9,200 79° 6,800 6,200 5,100
78° 10,800 10,200 9,000 78° 6,800 6,000 5,000
77° 10,800 9,900 8,800 77° 6,800 5,900 5,000
76° 10,800 9,600 8,700 76° 6,800 5,800 4,900
75° 10,800 9,300 8,500 75° 6,800 5,700 4,800
73° 10,500 8,900 8,200 73° 6,800 5,500 4,700
70° 9,600 8,300 7,700 70° 6,800 5,200 4,600
68° 9,100 7,900 7,400 68° 6,700 5,100 4,500
65° 8,200 7,200 6,800 65° 5,900 4,900 4,500
63° 7,500 6,700 6,400 63° 5,400 4,500 4,200
60° 6,700 6,100 5,800 60° 4,500 4,100 3,800
58° 5,800 5,400 5,100 58° 3,900 3,600 3,400
55° 4,700 4,400 4,200 55° 2,900 2,800 2,600
53° 4,100 3,700 3,600 53° 2,300 2,200 2,100
50° 3,200 3,000 2,800 50° 1,600 1,500 1,400
48° 2,700 2,400 2,300 48° 1,100 1,100 1,000
45° 2,000 1,800 1,700
43° 1,600 1,500
40° 1,100 1,100
ON OUTRIGGERS FULLY EXTENDED 23' 11-1/2"(7.3m) SPREAD
360
o
ROTATION
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 11,700 11,600 10,000 80° 7,300 6,500 5,200
79° 11,700 11,200 9,800 79° 7,300 6,400 5,100
78° 11,700 10,900 9,600 78° 7,300 6,200 5,100
77° 11,700 10,600 9,400 77° 7,300 6,100 5,000
76° 11,700 10,300 9,200 76° 7,300 6,000 5,000
75° 11,700 10,100 9,100 75° 7,300 5,900 5,000
73° 11,500 9,500 8,700 73° 7,300 5,700 4,900
70° 10,400 8,900 8,200 70° 7,300 5,400 4,700
68° 9,700 8,400 7,800 68° 7,100 5,300 4,600
65° 8,600 7,500 7,100 65° 6,200 5,100 4,600
63° 7,900 7,000 6,700 63° 5,700 4,700 4,400
60° 7,100 6,400 6,100 60° 5,100 4,300 4,000
58° 6,600 6,000 5,800 58° 4,700 4,000 3,800
55° 6,000 5,500 5,300 55° 4,200 3,600 3,500
53° 5,600 5,200 5,000 53° 3,900 3,400 3,300
50° 5,100 4,700 4,600 50° 3,500 3,100 3,000
48° 4,700 4,400 4,200 48° 3,200 2,900 2,700
45° 4,000 3,800 3,600 45° 2,700 2,600 2,300
43° 3,600 3,400 43° 2,400 2,300
40° 3,100 3,000 40° 2,000 1,900
38° 2,800 2,700 38° 1,700 1,700
35° 2,400 2,300 35° 1,400 1,400
33° 2,200 2,100 33° 1,200 1,200
30° 1,900 1,800 30° 1,000 1,000
25° 1,500 1,500
20° 1,200
15° 1,000
ON OUTRIGGERS FULLY EXTENDED 23' 11-1/2"(7.3m) SPREAD
360
o
ROTATION
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 14,600 14,000 10,700 80° 8,800 7,000 5,200
79° 14,600 13,600 10,600 79° 8,800 6,800 5,100
78° 14,600 13,300 10,500 78° 8,800 6,700 5,100
77° 14,600 12,900 10,300 77° 8,800 6,500 5,000
76° 14,600 12,700 10,200 76° 8,800 6,400 5,000
75° 14,600 12,400 10,100 75° 8,800 6,300 5,000
73° 14,600 11,900 10,000 73° 8,800 6,100 4,900
70° 13,700 11,200 9,700 70° 8,300 5,800 4,700
68° 13,000 10,800 9,600 68° 7,900 5,600 4,600
65° 12,100 10,300 9,500 65° 7,500 5,400 4,600
63° 11,600 10,000 9,300 63° 7,100 5,300 4,500
60° 10,100 9,100 8,500 60° 6,800 5,100 4,500
58° 8,900 8,100 7,600 58° 6,500 5,000 4,400
55° 7,500 6,900 6,500 55° 5,400 4,800 4,400
53° 6,700 6,200 5,900 53° 4,800 4,300 4,200
50° 5,700 5,300 5,000 50° 4,000 3,600 3,500
48° 5,100 4,800 4,500 48° 3,500 3,200 3,100
45° 4,300 4,100 3,800 45° 2,900 2,700 2,500
43° 3,900 3,700 43° 2,600 2,400
40° 3,300 3,200 40° 2,100 2,000
38° 3,000 2,900 38° 1,800 1,700
35° 2,500 2,400 35° 1,500 1,400
33° 2,300 2,200 33° 1,300 1,200
30° 2,000 1,900 30° 1,000 1,000
25° 1,500 1,500
20° 1,200
15° 1,000
C
:Loaded boom angle (deg.)
R
:Load radius in feet
W
:Rated lifting capacity in pounds
C
139.8'(42.63m) Boom(telescoping mode II) + 33.2' (10.1m) Jib
139.8'(42.63m) Boom(telescoping mode II) + 58.1' (17.7m) Jib
125.5'(38.25m) Boom(telescoping mode I) + 33.2' (10.1m) Jib
125.5'(38.25m)Boom(telescoping mode I) + 58.1' (17.7m) Jib
ON OUTRIGGERS FULLY EXTENDED 23' 11-1/2"(7.3m) SPREAD
360
o
ROTATION
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
C C
154.2' (47.0m) Boom + 33.2' (10.1m) Jib
154.2' (47.0m) Boom + 58.1' (17.7m) Jib
C C
C
8

A
B
C
(12m)
C
(16.38m)
C
C
C
C
C
C
C
C
C
C
C
C
C
(47m)
8 200000 102700
10 175700 102700 90200 40100
12 153600 102700 90200 40100
15 128200 102700 89900 40100 42500 35500
20
94800
98000
75000
40100
42500
35500
40100
33300
35500
32200
25
67800
65800
59500
40100
42500
35500
40100
33300
35500
32200
33300
28700
30
46900
45400
44000
40100
42500
35500
40100
33300
35500
30200
33300
26300
26700
24300
35
33400
32200
36200
34300
35500
35400
31600
35100
27300
30900
24000
26700
24100
20900
40
25400
24400
30400
26400
31100
27500
29300
28300
24900
28400
22000
25300
22300
20900
45
19800
18900
24600
20800
25300
21800
25600
22600
22900
23100
20200
23500
20700
20700
50 14800 20300 16700 21000 17700 21300 18400 20400 18900 18700 19300 19300 19400
55
11600
17000
13400
17600
14500
18000
15200
18000
15700
17400
16100
17300
16400
60 9200 14300 10800 14900 11900 15400 12600 15600 13100 15700 13400 14700 13700
65
8700
12800
9700
13200
10500
13400
11000
13600
11300
12500
11600
70 7000 11000 8000 11400 8700 11600 9200 11800 9600 10700 9900
75 5600 9500 6500 9900 7200 10100 7700 10300 8100 9300 8400
80 5200 8600 5900 8800 6400 9000 6800 8000 7100
85 4200 7500 4800 7700 5300 7800 5700 6900 6000
90 3900 6700 4400 6900 4700 5900 5000
95 3100 5900 3500 6000 3900 5000 4200
100 2400 5200 2800 5200 3200 4300 3400
105 2100 4600 2500 3600 2800
110 1600 4000 1900 3000 2200
115 3500 1400 2400 1600
120 2000
125 1600
130
135
140
D
Telescopin
g mode
2nd boom
3rd boom
4th boom
Top boom
A
C
B
(12m)
B
(16.38m)
B
(20.75m)
B
(20.75m)
B
(25.13m)
B
(25.13m)
B
(29.5m)
B
(29.5m)
B
(33.88m)
B
(33.88m)
B
(38.25m)
B
(38.25m)
B
(42.63m)
B
(42.63m)
B
(47m)
0
o
Telescopin
g mode
A
:Boom length in feet
B
:Load radius in feet
C
:Loaded boom angle (deg.)
D
:Minimum boom angle (deg.) for indicated length (no load)
I II I, III II I II
139.8' 154.2'
I, II I I II I II I II
111.1' 125.5' 125.5' 139.8'
21' 11-3/4"(6.7m) SPREAD 360°ROTATION
39.4' 53.7' 68.1' 68.1' 82.4' 82.4' 96.8' 96.8' 111.1'
83 100 100
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED
50 83 66 10016 50 33 66
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
360
o
ROTATION
39.4' 53.7' 68.1'(20.75m) 82.4'(25.13m) 96.8'(29.5m) 111.1'(33.88m) 125.5'(38.25m) 139.8'(42.63m) 154.2'
Telescoping conditions (
％）
I, II I I II I II I II I II I II I II I, II
0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
0 0 0 33
9

3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 10,800 10,800 9,400 80° 6,800 6,300 5,100
79° 10,800 10,400 9,200 79° 6,800 6,200 5,100
78° 10,800 10,200 9,000 78° 6,800 6,000 5,000
77° 10,800 9,900 8,800 77° 6,800 5,900 5,000
76° 10,800 9,600 8,700 76° 6,800 5,800 4,900
75° 10,800 9,300 8,500 75° 6,800 5,700 4,800
73° 10,500 8,900 8,200 73° 6,800 5,500 4,700
70° 9,600 8,300 7,700 70° 6,800 5,200 4,600
68° 8,700 7,700 7,000 68° 6,300 5,100 4,500
65° 6,700 6,000 5,600 65° 4,700 4,000 3,700
63° 5,600 5,100 4,700 63° 3,800 3,300 3,100
60° 4,300 3,900 3,700 60° 2,800 2,400 2,300
58° 3,500 3,300 3,100 58° 2,200 1,900 1,800
55° 2,600 2,400 2,300 55° 1,400 1,300 1,200
53° 2,100 1,900 1,800 53° 1,000
50° 1,400 1,300 1,200
48° 1,000
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
360
o
ROTATION
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 11,700 11,600 10,000 80° 7,300 6,500 5,200
79° 11,700 11,200 9,800 79° 7,300 6,400 5,100
78° 11,700 10,900 9,600 78° 7,300 6,200 5,100
77° 11,700 10,600 9,400 77° 7,300 6,100 5,000
76° 11,700 10,300 9,200 76° 7,300 6,000 5,000
75° 11,700 10,100 9,100 75° 7,300 5,900 5,000
73° 11,500 9,500 8,700 73° 7,300 5,700 4,900
70° 10,400 8,900 8,200 70° 7,300 5,400 4,700
68° 9,700 8,400 7,800 68° 7,100 5,300 4,600
65° 8,600 7,500 7,100 65° 6,200 5,100 4,600
63° 7,900 7,000 6,700 63° 5,700 4,700 4,400
60° 6,600 6,000 5,600 60° 4,700 4,000 3,800
58° 5,800 5,200 5,000 58° 4,000 3,400 3,300
55° 4,700 4,300 4,100 55° 3,100 2,700 2,600
53° 4,100 3,700 3,600 53° 2,600 2,300 2,200
50° 3,300 3,000 2,900 50° 2,000 1,800 1,700
48° 2,800 2,600 2,600 48° 1,600 1,500 1,400
45° 2,200 2,100 2,100 45° 1,200 1,000 1,000
43° 1,900 1,800
40° 1,500 1,400
38° 1,200 1,100
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
360
o
ROTATION
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 14,600 14,000 10,700 80° 8,800 7,000 5,200
79° 14,600 13,600 10,600 79° 8,800 6,800 5,100
78° 14,600 13,300 10,500 78° 8,800 6,700 5,100
77° 14,600 12,900 10,300 77° 8,800 6,500 5,000
76° 14,600 12,700 10,200 76° 8,800 6,400 5,000
75° 14,600 12,400 10,100 75° 8,800 6,300 5,000
73° 14,600 11,900 10,000 73° 8,800 6,100 4,900
70° 13,700 11,200 9,700 70° 8,300 5,800 4,700
68° 13,000 10,800 9,600 68° 7,900 5,600 4,600
65° 10,700 9,000 8,400 65° 7,500 5,400 4,600
63° 9,200 7,800 7,400 63° 6,500 5,300 4,500
60° 7,400 6,400 6,100 60° 5,100 4,400 4,100
58° 6,400 5,600 5,400 58° 4,400 3,700 3,600
55° 5,200 4,600 4,400 55° 3,400 3,000 2,900
53° 4,500 4,000 3,900 53° 2,900 2,500 2,400
50° 3,600 3,200 3,200 50° 2,200 1,900 1,900
48° 3,100 2,800 2,700 48° 1,800 1,600 1,500
45° 2,400 2,200 2,100 45° 1,300 1,100 1,100
43° 2,000 1,800
40° 1,500 1,400
38° 1,200 1,100
C
:Loaded boom angle (deg.)
R
:Load radius in feet
W
:Rated lifting capacity in pounds
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
154.2' (47.0m) Boom + 33.2' (10.1m) Jib 154.2' (47.0m) Boom + 58.1' (17.7m) Jib
C C
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
360
o
ROTATION
C139.8'(42.63m) Boom(telescoping mode II) + 33.2' (10.1m) Jib C139.8'(42.63m) Boom(telescoping mode II) + 58.1' (17.7m) Jib
C125.5'(38.25m) Boom(telescoping mode I) + 33.2' (10.1m) Jib C125.5'(38.25m)Boom(telescoping mode I) + 58.1' (17.7m) Jib
10

A
B
C
(12m)
C
(16.38m)
C
C
C
C
C
C
C
C
C
C
C
C
C
(47m)
8 191600 102700
10 164000 102700 90200 40100
12 142400 102700 90200 40100
15
113500
102700
89900
40100
42500
35500
20
75400
73400
67200
40100
42500
35500
40100
33300
35500
32200
25
48200
46700
45400
40100
42500
35500
40100
33300
35500
32200
33300
28700
30
33900
32700
31500
35500
33600
35500
34800
33300
35500
30200
33300
26300
26700
24300
35
23900
23000
28900
24900
29500
26000
29900
26800
27300
27300
24000
26700
24100
20900
40
18000
17100
22800
19000
23400
20100
23800
20800
24100
21400
22000
21800
22300
20900
45
13700
12900
18300
14800
19000
15800
19400
16500
19600
17000
19800
17400
18700
17700
50 9700 14900 11500 15600 12600 16000 13200 16300 13800 16400 14100 15300 14400
55 7200 12300 8900 13000 10000 13400 10700 13700 11200 13800 11600 12700 11900
60 5300 10300 6900 10800 7900 11300 8600 11600 9100 11700 9500 10700 9800
65 5200 9100 6200 9500 6900 9800 7500 10000 7800 9000 8100
70 3800 7700 4800 8100 5500 8300 6000 8500 6400 7500 6700
75 2600 6500 3600 6800 4300 7100 4800 7300 5200 6300 5500
80 2600 5800 3200 6000 3700 6200 4100 5200 4400
85 1700 4900 2300 5100 2800 5300 3200 4300 3500
90 1600 4300 2100 4500 2400 3500 2700
95 3700 1400 3800 1700 2800 2000
100 3100 3200 1100 2200 1400
105 2600 1700
110 2200 1100
115 1700
120
125
130
135
140
D
Telescopin
g mode
2nd boom
3rd boom
4th boom
Top boom
A
C
B
(12m)
B
(16.38m)
B
(20.75m)
B
(20.75m)
B
(25.13m)
B
(25.13m)
B
(29.5m)
B
(29.5m)
B
(33.88m)
B
(33.88m)
B
(38.25m)
B
(38.25m)
B
(42.63m)
B
(42.63m)
B
(47m)
0
o
Telescopin
g mode
A
:Boom length in feet
B
:Load radius in feet
C
:Loaded boom angle (deg.)
D
:Minimum boom angle (deg.) for indicated length (no load)
18' 1/2"(5.5m) SPREAD 360°ROTATION 154.2'
I, II
100
100
100
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED
125.5'
66
100
Telescoping conditions (
％）
I, II
100
II I II
100 100 50
ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
360
o
ROTATION 139.8'(42.63m) 154.2'96.8'(29.5m)82.4'(25.13m)39.4' 53.7' 68.1'(20.75m)
6650 8366
139.8' 139.8'
111.1'(33.88m) 125.5'(38.25m)
0
83
83 83
111.1'
I
39.4' 53.7' 68.1' 68.1' 82.4' 82.4' 96.8' 96.8'
100
0 0 0 83 10033 16 50 33
I II III II I
111.1' 125.5'
I, II I I II I II I II
100
0 0 0 33 16 50 33 10050
0 0 0 33 16 50 33 83
I II
0 50 100 0 100 0 100
I
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
66
I, II I I III
0
66
66
II
0
II
100
100
50
11

3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 10,800 10,800 9,400 80° 6,800 6,300 5,100
79° 10,800 10,400 9,200 79° 6,800 6,200 5,100
78° 10,800 10,200 9,000 78° 6,800 6,000 5,000
77° 10,800 9,900 8,800 77° 6,800 5,900 5,000
76° 10,800 9,600 8,700 76° 6,800 5,800 4,900
75° 10,800 9,300 8,500 75° 6,800 5,700 4,800
73° 10,100 8,300 7,600 73° 6,800 5,500 4,700
70° 7,400 6,200 5,700 70° 5,200 4,200 3,800
68° 6,000 5,000 4,700 68° 4,100 3,300 3,000
65° 4,300 3,700 3,500 65° 2,700 2,300 2,100
63° 3,400 2,900 2,800 63° 2,000 1,700 1,600
60° 2,300 2,000 1,900 60° 1,100
58° 1,700 1,400 1,400
ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
360
o
ROTATION
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 11,700 11,600 10,000 80° 7,300 6,500 5,200
79° 11,700 11,200 9,800 79° 7,300 6,400 5,100
78° 11,700 10,900 9,600 78° 7,300 6,200 5,100
77° 11,700 10,600 9,400 77° 7,300 6,100 5,000
76° 11,700 10,300 9,200 76° 7,300 6,000 5,000
75° 11,700 10,100 9,100 75° 7,300 5,900 5,000
73° 11,500 9,500 8,700 73° 7,300 5,700 4,900
70° 10,200 8,600 7,800 70° 7,300 5,400 4,700
68° 8,500 7,300 6,700 68° 6,100 5,000 4,400
65° 6,600 5,800 5,400 65° 4,600 3,900 3,400
63° 5,600 4,900 4,600 63° 3,800 3,200 2,800
60° 4,300 3,800 3,600 60° 2,800 2,400 2,100
58° 3,600 3,200 3,000 58° 2,200 1,900 1,700
55° 2,700 2,400 2,300 55° 1,500 1,300 1,200
53° 2,200 2,000 1,900 53° 1,100
50° 1,500 1,400 1,300
48° 1,100 1,000 1,000
ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
360
o
ROTATION
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
3.5
o
Tilt
25
o
Tilt
45
o
Tilt
R
W
R
W
R
W
R
W
R
W
R
W
80° 14,600 14,000 10,700 80° 8,800 7,000 5,200
79° 14,600 13,600 10,600 79° 8,800 6,800 5,100
78° 14,600 13,300 10,500 78° 8,800 6,700 5,100
77° 14,600 12,900 10,300 77° 8,800 6,500 5,000
76° 14,600 12,700 10,200 76° 8,800 6,400 5,000
75° 14,600 12,400 10,100 75° 8,800 6,300 5,000
73° 14,600 11,900 10,000 73° 8,800 6,100 4,900
70° 11,300 9,500 8,600 70° 8,300 5,800 4,700
68° 9,500 8,100 7,400 68° 6,900 5,500 4,600
65° 7,300 6,300 5,900 65° 5,200 4,200 3,900
63° 6,100 5,400 5,000 63° 4,300 3,500 3,300
60° 4,700 4,200 3,900 60° 3,100 2,600 2,500
58° 3,900 3,500 3,300 58° 2,500 2,100 2,000
55° 2,900 2,600 2,500 55° 1,700 1,400 1,400
53° 2,300 2,100 2,000 53° 1,200 1,000 1,000
50° 1,600 1,500 1,400
48° 1,100 1,100 1,000
C
:Loaded boom angle (deg.)
R
:Load radius in feet
W
:Rated lifting capacity in pounds
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
154.2' (47.0m) Boom + 33.2' (10.1m) Jib
154.2' (47.0m) Boom + 58.1' (17.7m) Jib
C C
ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
360
o
ROTATION
139.8'(42.63m) Boom(telescoping mode II) + 58.1' (17.7m) Jib
C
125.5'(38.25m) Boom(telescoping mode I) + 33.2' (10.1m) Jib
C
125.5'(38.25m)Boom(telescoping mode I) + 58.1' (17.7m) Jib
C
139.8'(42.63m) Boom(telescoping mode II) + 33.2' (10.1m) Jib
C
12

A
B
C
(12m)
C
(16.38m)
C
C
C
C
C
C
C
C
C
C
C
C
C
(47m)
8
143900
102700
10
94900
93000
90200
40100
12 66900 65200 63700 40100
15
44700
43400
42000
40100
42500
35500
20
26300
25400
24300
30400
26400
31000
27500
31400
28300
31700
25
17000
16100
15300
20900
17200
21500
18200
21800
18900
22100
19500
22300
30
11400
10400
9600
14900
11600
15700
12500
16000
13200
16200
13800
16400
14100
15300
35 6600 5800 10900 7700 11600 8700 12100 9400 12300 9900 12500 10300 11400 10500
40 3900 3100 8100 4900 8700 5900 9200 6600 9500 7100 9600 7500 8600 7700
45 1800 1100 5900 2800 6500 3700 7000 4500 7300 5000 7500 5400 6500 5600
50 4300 1100 4900 2100 5300 2800 5600 3300 5800 3700 4800 4000
55 2900 3500 3900 1500 4200 2000 4400 2400 3500 2700
60 1900 2400 2800 3100 3300 1300 2300 1500
65 1500 1900 2200 2300 1400
70 1100 1400 1500
75
80
85
90
95
100
105
110
115
120
125
130
135
140
D
Telescopin
g mode
2nd boom
3rd boom
4th boom
Top boom
A
C
B
(12m)
B
(16.38m)
B
(20.75m)
B
(20.75m)
B
(25.13m)
B
(25.13m)
B
(29.5m)
B
(29.5m)
B
(33.88m)
B
(33.88m)
B
(38.25m)
B
(38.25m)
B
(42.63m)
B
(42.63m)
B
(47m)
0
o
Telescopin
g mode
A
:Boom length in feet
B
:Load radius in feet
C
:Loaded boom angle (deg.)
D
:Minimum boom angle (deg.) for indicated length (no load)
NOTE
:
The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
number of parts of line listed in the chart.
Standard number of part line for outrigger operation should be according to the following table. Single top
Jib
1
I, II
100
100
100
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MIN EXTENDED
1005066 100
0
Telescoping conditions (
％）
I, II
1001000100 0 100 0
ON OUTRIGGERS MIN EXTENDED 8' 10-1/4"(2.8m) SPREAD
360
o
ROTATION 139.8'(42.63m) 154.2'39.4' 53.7' 68.1'(20.75m) 111.1'(33.88m) 125.5'(38.25m)
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
66
I, II I I III
0 50 100 100 50
0 0 0 33 16 50 33 83
0 0 33 16 50 33 100 83
100
66
33 16 50 33 6650 83
0
I IIIII II III I II
I II I III, II I I II I II III II I
111.1'
96.8'(29.5m)82.4'(25.13m)
39.4' 53.7'
66 50
68.1' 68.1'
0100 100
66
82.4' 82.4' 96.8' 96.8' 125.5' 139.8' 139.8'
0
83
83
111.1'
8' 10-1/4"(2.8m)SPREAD 360°ROTATION 154.2'
0 0 83100
4
125.5'
68.1' to 154.2'
(meters)
(12m)
(12m to20.75m) (20.75m to 47m)
Boom length in feet
39.4'
39.4' to68.1'
I, II
I, II
Number of part line
16
4
I
Telescoping mode
I, II
8
II
13

WARNING AND OPERATING INSTRUCTIONS
FOR LIFTING CAPACITIES
GENERAL
1.
RATED LIFTING CAPACITIES apply only to the machine as
9.
When boomlength is between values listed, refer to the
originally manufactured and normally equipped by TADANO
rated lifting capacities of the next longer and next shorter
LTD. Modifications to the machine or use of optional
booms for the same radius. The lesser of the two rated lifting
equipment other than that specified can result in a reduction
capacities shall be used.
of capacity.
10.
When making lifts at a load radius not shown, use the next
2.
Hydraulic cranes can be hazardous if improperly
longer radius to determine allowable capacity.
operated or maintained. Operation and maintenance of this
11.
Load per line should not exceed 14,600 lbs. (6,600kg) for
machine must be in compliance with information in the
main winch andauxiliary winch.
Operation and Maintenance Manual
supplied with
12.
Check the actual number of parts of line with LOAD MOMENT
the crane. If this manual is missing, order a replacement
INDICATOR (AML-C) before operation. Maximum lifting
through the distributor.
capacity is restricted by the number of parts of line of LOAD
3.
The operator and other personnel associated with this
MOMENT INDICATOR (AML-C). Limited capacity is as
machine shall fully acquaint themselves with the latest
determined from the formula, Single line pull for main winch
American National Standards Institute (ANSI) safety
(14,600 lbs.) x number of parts of line.
standards for cranes.
13.
The boom angle before loading should be greater to account
for deflection. For rated lifting capacities, the loaded boom
SET UP
angle and the load radius is for reference only.
1.
Rated lifting capacities on the load chart are the maximum
14.
The 39.4' (12.0m) boomlength capacities are based on boom
allowable crane capacities. They are based on the machine
fully retracted. If not fully retracted [less than 53.7'(16.38m)
standing level on firm supporting surface under ideal job
boom length], use the rated lifting capacities for the 53.7' (16.38m)
conditions. Depending on the nature of the supporting
boom length.
surface, it may be necessary to have structural supports
15.
Extension or retraction of the boom with loads may be
under the outrigger floats or tires to spread the loads to a
attempted within the limits of the RATED LIFTING CAPACITIES.
larger surface.
The ability to telescopeloads is limited by hydraulic pressure,
2.
For outrigger operation, outriggers shall be properly extended
boom angle, boom length, crane maintenance, etc.
with tires free of supporting surface before operating crane.
16.
For lifting capacity of single top, reduce the rated lifting
capacities of relevant boom according to a weight reductions
OPERATION
for auxiliary load handling equipment. Capacities of single top
1.
Rated lifting capacities have been tested to and meet
shall not exceed 14,600 lbs. (6,600kg) including main hook.
minimum requirements of SAE J1063-Cantilevered Boom
17.
When base jib or top jib or both jib removing, jib state switch
Crane Structures Method of Test.
select removed.
2.
Rated lifting capacities do not exceed 85 % of the tipping
18.
When erecting and stowing jib, be sure to retain it by hand or by
load on outriggers fully extended as determined by SAE
other means to prevent its freemovement.
J765-Crane Stability Test Code.
19.
Use "ANTI-TWO BLOCK" disable switch when erecting and
Rated lifting capacities for partially extended outriggers are
stowing jib and when stowing hook block. While the switch is
determined from the formula, Rated Lifting Capacities
pushed, the hoist does not stop, even when overwind condition
=(Tipping Load - 0.1 x Tip Reaction)/1.25.
occurs.
3.
Rated lifting capacities above bold lines in the chart are
20.
For boom length with 33.2' (10.1m) jib, rated lifting capacities are
based on crane strength and those below, on its stability.
determined by loaded boom angle only in the column headed
They are based on actual load radius increased by boom
"154.2' (47.0m) boom + 33.2' (10.1m) jib".
deflection.
For boom length with 58.1' (17.7 m) jib, rated lifting capacities
4.
The weight of handling device such as hook blocks, slings,
are determined by loaded boom angle only in the column
etc., must be considered as part of the load and must be
headed "154.2' (47.0m) boom + 58.1' (17.7m) jib".
deducted from the lifting capacities.
For angles not shown, use the next lower loaded boom angle
5.
Rated lifting capacities are based on freely suspended loads
to determine allowable capacity.
and make no allowance for such factors as the effect of wind,
21.
When lifting a load by using jib (aux. winch) and boom (main
sudden stopping of loads, supporting surface conditions,
winch) simultaneously, do the following:
inflation of tires, operating speeds, side loads, etc. Side pull
h
Enter the operation status as jib operation, not as boom
on the boom or jib is extremely dangerous.
operation.
6.
Rated lifting capacities do not account for wind on lifted load
h
Before starting operation, make sure that mass of load is
or boom. We recommend against working under the condition
within rated lifting capacity for jib.
that the load is out of control due to a strong wind.During
boom lift, consider that the rated lifting capacity is reduced by
DEFINITIONS
50% when the wind speed is 20mph(9m/s) to 27mph(12m/s);
1.
Load Radius: Horizontal distance from a projection of the axis
reduced by 70% when the wind speed is 27mph(12m/s) to
of rotation to supporting surface before loading to the center of
31mph(14m/s).If the wind speed is 31mph(14m/s) or over,
the vertical hoist line or tackle with load applied.
stop operation. During jib lift, stop operation if the wind speed
2.
Loaded Boom Angle: The angle between the boom base
is 20mph(9m/s)
section and the horizontal, after lifting the rated lifting capacity
7.
Rated lifting capacities at load radius shall not be exceeded.
at the load radius.
Do not tip the crane to determine allowable loads.
3.
Working Area: Area measured in a circular arc about the
8.
Do not operate at boom lengths, radii, or boomangle, where
centerline of rotation.
no capacities are shown. Crane may overturn without any
4.
Freely Suspended Load: Load hanging free with no direct
load on the hook.
external force applied except by the hoist line.
5.
Side Load: Horizontal side force applied to the lifted load either
on the ground or in the air.
14

ON RUBBER STATIONARY
AOver Front 360
o
Rotation
68.1'
96.8'
68.1'
96.8'
B
C
(12m)
C
(20.75m)
C
(29.5m)
C
(12m)
C
(20.75m)
C
(29.5m)
12
60,000
38,000
15
49,600
28,500
20
37,500
35,000
17,500
20,000
25
28,500
29,500
28,500
10,400
14,000
14,000
30
21,500
24,000
24,000
6,500
9,500
10,000
35
19,200
19,500
6,500
7,400
40
15,200
16,000
4,500
5,400
45
12,200
13,000
3,000
3,900
50
9,700
10,600
1,800
2,700
55
8,000
8,800
1,700
60
6,500
7,400
65
6,100
70
5,000
75
4,100
80
3,400
85
2,700
D
Telescoping
mode
2nd boom
3rd boom
4th boom
Top boom
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON RUBBER STATIONARY
AOver Front 360
o
Rotation
68.1'
C
B
(12m)
B
(20.75m)
B
(12m)
0
o
ON RUBBER CREEP
A
Over Front
68.1'
96.8'
A
:Boom length in feet
B
C
(12m)
C
(20.75m)
C
(29.5m)
B
:Load radius in feet
12
45,000
D
:Minimum boom angle (deg.)
15
36,600
for indicated length (noload)
20
26,800
29,200
25
20,500
22,800
23,400
30
15,600
18,200
18,900
35
14,800
15,500
40
12,000
12,900
45
9,800
10,600
50
7,900
8,900
55
6,500
7,300
60
5,200
6,100
65
5,000
70
4,100
75
3,200
80
2,500
D
Telescoping
mode
2nd boom
3rd boom
4th boom
Top boom
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE
ON RUBBER CREEP
A
Over Front
68.1'
C
B
(12m)
B
(20.75m)
0
o
NOTE
:
The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based
on the standard number of parts of line listed in the chart.
Standard number of parts of line for on rubber operation should be according to the
following table.
Boom length in feet
39.4' to 96.8'
Single top
(meters)
(12m)
(12m to 29.5m)
Number of parts of line
6
4
1
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
39.4' 39.4'
39.4'
I, II II II
0 0 0
0 33 66
0 33 66
0 33 66
I, II II II
000
0 33 66
Telescoping conditions (
％）
0 33 66
0 33 66
I, II II II
0 0 0
66
0 33 66
39.4'
39.4'
39.4'
39.4'
0 33 66
Telescoping conditions (
％）
0 33
15

WARNING AND OPERATING INSTRUCTIONS
FOR ON RUBBER LIFTING CAPACITIES
1.Rated lifting capacities on rubber are in pounds and do not exceed
6
Over front operation shall be performed within two degrees in front of
75 % of tipping loads as determined by SAE J765-Crane Stability
chassis.
Test Code.
7
On rubber lifting with "jib" is not permitted. Maximum permissible
2.Rated lifting capacities shown in the chart are based on condition
boom length is 96.8 ft. (29.5m).
that crane is set on firm level surfaces with axle oscillation lockout
8
When making lift on rubber stationary, set parking brake.
applied. Those above bold lines are based on tire capacity and
9
For creep operation, boom must be centered over front of machine,
those below, on crane stability. They are based on actual load
swing lock engaged, and load restrained from swinging. Travel slowly
radius increased by tire deformation and boom deflection.
and keep the lifted load as close to the ground as possible, and
3.If the axle oscillation lockout cylinders contain air, the axle will not
especially avoid any abrupt steering, accelerating or braking.
be locked completely and rated lifting capacities may not be
10
Do not operate the crane while carrying the load.
obtainable. Bleed the cylinders according to the operation safety
11
Creep is motion for crane not to travel more than 200 ft. (60 m) in any
and maintenance manual.
30 minute period and to travel at the speed of less than 1 mph
4.Rated lifting capacities are based on proper tire inflation, capacity
(1.6km/h).
and condition. Damaged tires are hazardous to safe operation of
12
For creep operation, set Drive select switch to "4-WHEEL (Lo)" and
crane.
set gear shift lever to "1".
5.Tires shall be inflated to correct air pressure.
Air Pressure
57 psi (4.0 kgf/cm2)
WARNING AND OPERATING INSTRUCTIONS
FOR USING THE LOAD MOMENT INDICATOR (AML-C)
1.
When operating crane on outriggers:
When a load is lifted in the front position and then swung
Set P.T.O. switch to "ON".
to the side area, make sure the value of the LOAD
Press the outrigger mode select key to register for the
MOMENT INDICATOR(AML-C) is below the 360
o
lifting
outrigger operation. Press the register key, then the outrigger
capacity.
mode indicative symbol changes from flashing to a solid light.
(2)
For creep operation.
Press the lift mode select key to select the lift status that
The creep capacities are attainable only when boom is
corresponds to the actual boom configuration.
in the straight forward position of chassis and the over
Each time the lift mode select key is pressed, the ststus changes.
front position symbol is on. If boom is not in the straight
Press the register key to register the lift status, then the lift
forward position of chassis , never lift load.
indicative symbol changes from flashing to a solid light.
3.
A swing does not automatically stop even if the crane
when mounting and stowing jib, select the jib set status.
becomes overloaded.
(the jib state indicative symbol will be flashing.)
4.
During crane operation, make sure that the displays on front
2.
When operating crane on rubber:
panel are in accordance with actual operating conditions.
Set P.T.O. switch to "ON".
5.
The displayed values of LOAD MOMENT INDICATOR
Press the outrigger mode select key. The on-tire mode
(AML-C) are based on freely suspended loads and make no
indicative symbol comes on. Each time the outrigger mode
allowance for such factors as the effect of wind, sudden
select key is pressed the status changes. Select the creep
stopping of loads, supporting surface conditions, inflation of
operation, the on-tire mode indicative symbol flicker.
tire, operating speed, side loads, etc.
Press the lift mode select key to register the boom or single top
For safe operation, it is recommended when extending and
lift.
lowering boom or swinging, lifting loads shall be
However, pay attention to the following.
appropriately reduced.
(1)
For stationary operation.
6.
LOAD MOMENT INDICATOR (AML-C) is intended as an aid
The front capacities are attainable only when the over front
to the operator. Under no condition should it be relied upon
position symbol comes on. When the boom is more than
to replace use of capacity charts and operating instruction.
2 degrees from centered over front of chassis, 360
o
Sole reliance upon LOAD MOMENT INDICATOR (AML-C)
capacities are in effect.
aids in place of good operating practice can cause an
accident. The operator must exercise caution to assure
safety.
TR-1000XL Axle weight distribution chart
Base machine
Remove:
1.
6.6metric ton hook ball
-462
138
-147
-209
62
2.
100t hook block
-3,660
1,764
-860
-1,660
800
3.
Top jib
-964
245
-326
-437
111
4.
Base jib
-3,706
1,821
-855
-1,681
826
5.
Auxiliary lifting sheave
-325
216
-49
-147
98
6.
Removable Counterweihgt
9,202
-30,862
-9,825
4,174
-13,999
(with Auxiliary Hoist&wire)
52,275 25,990 26,285
-21,660
Rear
-324
-1,896
-1,885
115,245
57,298 57,948
Kilograms
GVW Front Rear
Tires
29.5-25 34PR
-109
Pounds
GVW Front
-719
16

MEMO
TADANO AMERICA CORPORATION
333 NORTHPARK CENTRAL DRIVE, SUITE Z
HOUSTON, TEXAS 77073, U.S.A.
PHONE: [phone]
FAX: [phone]
http://www.tadano-cranes.com/
Form No. GR-1000-2-00101
17