Takstar EBS-653 User manual

EBS-653 定阻吸顶音箱说明书
EBS-653×2
说明书×1
欢迎使用EBS-653 定阻吸顶音箱，使用前请您仔细阅读说明书，以便能正确的
操作使用。
若存在有疑问或者您有宝贵的建议，可通过拨打得胜官方服务
热线400 6828 333 或微信扫描二维码关注得胜官方公众号与我们
联系。
■ 标准配置
■ 产品特性
■ 适用场合
■ 技术参数
■ 产品图示
■ 产品尺寸图
■ 安全警示
■ 产品安装
• 6.5英寸三分频专业级嵌入式安装扬声器，面板支架材料防潮、防水、抗紫外线
• 中、低音音盆采用特种玻纤材质，特点是质量轻、刚性强、内部阻力适中、耐疲
劳、抗腐蚀、抗空气振动对其产生的不良影响。音乐重放时低频、中频平衡干净，
音色华丽、保真度高，在发烧音响中应用较广。此款玻纤材料还掺入碳纤成分，以
提升音盆刚性，其性能优于普通玻纤
• 中、高音钕磁设计；高音采用0.75英寸钛膜。中音、高音可同步调节辐射角度，整
体声音温暖厚实，中音饱满，高音细腻柔和，穿透力强
• 系统采用无边框、网罩吸附式设计，便于安装及维护
会议中心、酒店、餐厅、建筑背景音乐、家庭定制安装影院等多种用途
• 额定功率：60W(AES)
• 额定阻抗：8Ω
• 频率响应（±3dB）：60Hz-20kHz
• 灵敏度（1W/1M）：86dB
• 覆盖角：H110×V150°
• 最大声压级：102dB
• 分频模式：无源三分频
• 安装方式：吊顶嵌入式/墙壁嵌入式
两种安装方式
• 安装开孔尺寸：246mm圆孔
• 安装深度：150mm
• 接线方式：按压式接线端子（IN：红+，黑-）
• 箱壳：ABS工程塑料
• 表面处理：黑色
• 高频：0.75寸钛膜、钕磁、可调节角度
• 中音：2寸玻纤胴体+NBR丁腈橡胶悬边，钕
磁，可调节角度
• 低频：6.5″×1，玻纤胴体+NBR丁腈橡胶悬
边单元
• 规格： φ269mm×H150mm
• 净重：2.14Kg
① 此图形纸板用来安装音响开孔使用，外径246mm
② 螺丝刀顺时针方向对4颗脚架螺丝转动为紧固音响
螺丝刀逆时针方向对4颗脚架螺丝转动为拆卸音响
③ 扬声器紧固后将金属网罩吸附在面板上
①
①
②
②
③
为避免电击、高温、着火、辐射、爆炸、机械危险以及使用不当等可能造成的
人身伤害或财产损失，使用本产品，请仔细阅读并遵守以下事项:
1. 使用产品时请确认所连接设备与本产品功率是否匹配以及合理调整音量大小，不
要在超过产品功率及大音量下长时间使用，以免造成产品异常和听力损伤；
2. 使用中若发现有异常（如冒烟、异味等），请立即关闭电源开关并拔掉电源插头，
然后将产品送经销商检修；
3. 本产品及附件都应放置在室内干燥通风处，勿长期存放在潮湿、灰尘多的环境，
使用中避免靠近火源、雨淋、进水、过度碰撞、抛掷、振动本机及覆盖通风孔，
以免损坏其功能；
4. 若产品需要固定于墙壁或天花板上时，请确保固定到位，防止因固定强度不足导
致产品发生跌落危险；
5. 使用该产品时需遵守相关安全规定，法律法规明确禁止使用场合请勿使用本机，
以免导致意外事故。
注：以上数据由得胜实验室测试得到，并拥有最终解释权！
269mm
246mm(安装开孔尺寸)
150mm
安装方式一(吊顶嵌入式安装）
① 此图形纸板用来安装音响开孔使用，外径246mm
② 根据声场的需求可以调节中高音安装架的角度获得最佳声场
③ 墙壁安装时请按此示意图定位
④ 扬声器紧固后将金属网罩吸附在面板上
安装方式二(墙壁嵌入式安装）
紧固螺丝，安装
及拆卸扬声器
中音，可调节角度
高音，可调节角度
安装脚架，安装及拆卸组件
强力磁铁，吸附金属网罩
红色按键端子，
正极输入
黑色按键端子，
负极输入
金属防尘网罩
③
④

Thank you for purchasing EBS-653 Fixed-Impedance In-Ceiling Speaker.
In order to correctly use the device, please read the manual carefully.
If you have any questions or suggestions, please contact our local dealer.
■ Standard Configuration
■ Features
■ Applications
■ Technical Specifications
■ Illustration
■ Dimensions
■ Safety Instructions
■ Installation
• Professional, three-way, 6.5" embedded speaker with moist-/water-/UV-resistant
panel frame
• Special fiberglass cone for squawker and woofer, featured by its light weight, high
rigidity, moderate internal resistance, and excellent resistance to fatigue, corrosion
and air vibration. Widely used by audiophiles, for music playback, it produces
balanced, clean bass and mids, with gorgeous timbre and high fidelity. Additional
carbon fiber is mixed in to improve cone rigidity for superior performance than
normal fiberglass
• Neodymium magnets for both squawker and tweeter, 0.75" titanium diaphragm
for tweeter (both drivers have synced adjustable angle), producing rich mids,
delicate, transparent highs and an overall warm sound
• Borderless design, magnetic grille, easy for installation and maintenance
BGM in hotel/restaurant/building/conference center, home theater.
• Rated Power: 60W (AES)
• Rated Impedance: 8Ω
• Frequency Response (±3dB):
60Hz-20kHz
• Sensitivity (1W/1M): 86dB
• Coverage Angle: H110*V150°
• Max SPL: 102dB
• Crossover: three-way, passive
• Installation: in-ceiling/in-wall
• Cut-out Size: ø246mm circle
• Installation Depth: 150mm
• Connection: push type terminal (IN: red+, black−)
• Enclosure: ABS plastic
• Finish: black
• HF: 0.75" titanium diaphragm, Nd magnet, rotatable
angle
• MF: 2" fiberglass cone + NBR surround, Nd magnet,
rotatable angle
• LF: 6.5" driver * 1, fiberglass cone + NBR surround
• Dimensions: ø269mm*H150mm
• Net Weight: 2.14Kg
① Use the cardboard to cut an opening, at 246mm outer diameter.
② Turn clockwise to tighten the 4 screws around the speaker frame;
Turn counterclockwise to loosen them for speaker removal.
③ Attach the metal grille on top of the secured speaker.
①
①
②
②
③
Note: The above data is measured by Takstar laboratory, and Takstar has the
final interpretation right!
269mm
246mm(Cut-out size)
150mm
Method 1 (In-Ceiling Installation)
① Use the cardboard to cut an opening, at 246mm outer diameter.
② Adjust the HF/MF driver’s installation bracket angle to achieve optimal sound
field as required.
③ For wall mounting, please follow this diagram for positioning
④ Attach the metal grille on top of the secured speaker.
Method 2 (In-Wall Installation)
Screw, for
installation/
removal
MF, adjustable angle
HF, adjustable angle
Mounting arm, for
installation/removal
Strong magnet,
attracts metal grille
Red push type
terminal,
positive input
Black push type
terminal,
negative input
Dust-proof
metal grille
③
④
EBS-653×2
User Manual×1
To avoid electric shock, overheat, fire, radiation, explosion, mechanical risk
and injury or property loss due to improper use, please read and observe the
following items before use:
1. Please check if the power of the connected equipment matches with that
of this product before operation. Adjust the volume to proper level during
operation. Do not operate at over-power or high-volume level for extended
time to avoid product malfunction or hearing impairment.
2. If there is any abnormality during use (e.g., smoke, strange odor), please
kill the power switch and unplug from power source, then send the product
to the local dealer for repair.
3. Keep this product and its accessories in a dry and ventilated area. Do not
store in a humid or dusty area for extended time. Keep away from fire, rain,
liquid intrusion, bumping, throwing, vibrating, or from blocking any ventilation
openings, to prevent malfunction.
4. The product must, when installed on walls or ceilings, be fixed firmly in
place at adequate strength to prevent from falling.
5. Please abide by safety rules during operation. Do not use the product in
places prohibited by laws or regulations to avoid accident.
EBS-653 Fixed-Impedance In-Ceiling Speaker