Takstar EKS-101 User manual

EKS-101音箱系列说明书
技术参数
注意事项
适用场合
标准配置
产品特性
欢迎使用EKS-101音箱，这款内置二分频的全频音箱，采用了平面波导技术，声波的相位延时传导和声波导相叠加技术。音箱灵敏度高、
音色优美、层次清晰、声音厚实。人声演唱音域宽，人声清晰、自然、逼真。主要应用于多功能厅、会议厅的主扩声或补声，慢摇吧，KTV工
程安装等。使用前请您仔细阅读说明书，以便能正确的操作使用。
用于多功能厅、会议厅的主扩声或补声，慢摇吧，KTV工程安装等。
EKS-101音箱
说明书
额定功率：250W
阻抗：8Ω
频率响应：60Hz-19kHz（±3dB）
灵敏度：95dB
覆盖角度：H100°×V 55°
最大声压级：120dB
分频模式：无源二分频
分频点：2300Hz
吊挂／安装：多点吊挂/支架（可旋转调整）
接线方式：1×NL4喇叭连接器，连接1+、1-使用，2+、2-可用于音箱并联
箱壳：15厘中纤板
表面处理：黑色催化聚亚安酯漆
高频：1.4″×1（36芯，26mm喉口）90磁钢
低频：10″×1（50芯），145磁钢
规格（mm）：320×320×520（W×D×H）
1. 匹配TAKSTAR品牌的EKA-3A功放使用。
2. 确保功率放大器和音箱的功率、阻抗相匹配，失衡搭配可导致设备损坏或音质效果不佳。
3. 音箱工作时的振幅较大，请不要在箱体上放置物品。
4. 音箱的安装需由专业工程人员进行，应固定牢靠，并选择安装在不易碰触的位置。
5. 搬运音箱时，请小心轻放，保护好音箱不受损坏。
EKS-101由一只10寸纸盆低音和一只36芯高音组成，高音采用了PEEK（下文将会介绍该材质的特性）膜片和铜包铝扁线音圈。低音采用耐
高温玻璃纤维骨架做成的50芯铜包铝绕组线圈。这种音圈特点是效率高、稳定性好。采用对称磁路设计，减少了二次谐波失真。分频器元件
的选用上，也采用了低损耗、小公差的无氧铜电感和高品质聚丙烯电容，以降低分频网络对音质的影响。
Peek（该音箱的高音扬声器膜片材质）又名聚醚醚酮，是特种塑料之一，长期使用耐温度250度左右，在高温下保持良好的力学性能，耐磨，
耐腐蚀。
箱体采用梯形结构，能抑制箱体内驻波，箱体采用15厘中纤板制作，外喷黑色耐磨点漆。后置一只提手和一只全铝托盘便于搬运和支撑。箱
体采用多点吊挂，应用方便灵活。
广东省电声工程技术研究开发中心
广东得胜电子有限公司制造
地址：广东省惠州市博罗县龙溪镇富康一路2号
电话：400 6828 333 传真：[phone] 邮箱： 邮编：516121 网址：www.takstar.com[email protected]

EKS-101
Speaker Cabinet Series User Manual
Specification
Caution
Application
Product Content
Features
Welcome to use EKS-101, the built-in 2 way full range speaker which adopts plane wave guide technology
clear and charming tone, wide and natural range to suit for multifunction
hall, conference hall, bar, KTV. Please read the user manual for better operation and keep it for reference in future.
for overlapping phase delay
transmission and the converted sound wave phase, high sensitivity,
Multi-function hall, conference hall, bar or KTV
EKS-101 speaker cabinet
User manual
Rated power: 250W
Impedance: 8Ω
Frequency response: 60Hz-19kHz (±3dB)
Sensitivity: 95dB
Coverage: H100°×V 55°
Max SPL: 120dB
Crossover mode: 2 way passive
Crossover frequency: 2300Hz
Suspension/installation: multiple flying points/pole mounting(adjustable angle)
Connection: 1×NL4 speaker connector, connect 1+, 1- for operation, connect 2+, 2- for parallel
Cabinet: 15mm MDF
Finish: black painting
HF: 1.4"×1 (36mm, 26mm throat) 90 magnet
LF: 10"×1 (50mm), 145 magnet
Dimension (mm): 320×320×520 (W×D×H)
1. Used with TAKSTAR EKA-3A power amplifier together.
2. Ensure to match the power and impedance of power amplifier and speaker cabinet. The unbalanced configuration leads to equipment damage
or bad sound effect.
3. Do not put objects on the cabinet due to the severe vibration amplitude of the speaker cabinet.
4. Ask professional technician for reliable installation in a place hard to touch.
5. Handle with care during transportation to avoid speaker cabinet damage.
EKS-101 consists of one 10 inch cone woofer and one 36 mm tweeter. The tweeter uses PEEK diaphragm and CCA voice coil.
The crossover components use extremely low consumption OFC inductor and high quality polyethylene capacitor
to reduce the sound quality loss.
The woofer uses
refractory glass fiber bobbin and 50mm CCA winding voice coil for high efficiency and reliable performance, and symmetric magnet to reduce
second harmonic distortion.
Refractory Peek diaphragm is durable and anti-erosive and keeps excellent mechanical performance in 250°C during long time operation.
15mm MDF trapezoidal enclosure eliminates standing wave inside, black painting finish for anti-moisture, handle for easy transportation, Al
socket for pole mounting, multiple flying points for flexible applications.
Guangdong Takstar Electronic Co., Ltd.
Address: No.2 Fu Kang Yi Rd., Longxi Boluo Huizhou, Guangdong 516121 China
Tel: [phone] Fax: [phone] Website: www.takstar.com E-mail: [e-mail]