Takstar EKS-101 User manual

欢迎使用EKS-101音箱，这款内置二分频的全频音箱，采用了
平面波导技术，声波的相位延时传导和声波导相叠加技术。音箱灵
敏度高、音色优美、层次清晰、声音厚实。人声演唱音域宽，人声
清晰、自然、逼真。主要应用于多功能厅、会议厅的主扩声或补
声，慢摇吧，KTV工程安装等。使用前请您仔细阅读说明书，以便
能正确的操作使用。
若存在有疑问或者您有宝贵的建议，可通过拨打
得胜官方服务热线400 6828 333 或微信扫描二维码关
注得胜官方公众号与我们联系。
1. 匹配TAKSTAR品牌的EKA-3A功放使用。
2. 确保功率放大器和音箱的功率、阻抗相匹配，失衡搭配可导致设
备损坏或音质效果不佳。
3. 音箱工作时的振幅较大，请不要在箱体上放置物品。
4. 音箱的安装需由专业工程人员进行，应固定牢靠，并选择安装在
不易碰触的位置。
5. 搬运音箱时，请小心轻放，保护好音箱不受损坏。
EKS-101由一只10寸纸盆低音和一只36芯高音组成，高音采用了
PEEK（下文将会介绍该材质的特性）膜片和铜包铝扁线音圈。低
音采用耐高温玻璃纤维骨架做成的50芯铜包铝绕组线圈。这种音
圈特点是效率高、稳定性好。采用对称磁路设计，减少了二次谐
波失真。分频器元件的选用上，也采用了低损耗、小公差的无氧
铜电感和高品质聚丙烯电容，以降低分频网络对音质的影响。
Peek（该音箱的高音扬声器膜片材质）又名聚醚醚酮，是特种塑
料之一，长期使用耐温度250度左右，在高温下保持良好的力学
性能，耐磨，耐腐蚀。
箱体采用梯形结构，能抑制箱体内驻波，箱体采用15厘中纤板制
作，外喷黑色耐磨点漆。后置一只提手和一只全铝托盘便于搬运
和支撑。箱体采用多点吊挂，应用方便灵活。
音箱系列说明书
EKS-101
产品特性
注意事项
用于多功能厅、会议厅的主扩声或补声，慢摇吧，KTV工程安装等。
EKS-101音箱
说明书
适用场合
标准配置
9TKS101S1A
为避免电击、高温、着火、辐射、爆炸、机械危险以及使用不当
等可能造成的人身伤害或财产损失，使用本产品，请仔细阅读并遵
守以下事项:
1. 使用产品时请确认所连接设备与本产品功率是否匹配以及合理调
整音量大 小，不要在超过产品功率及大音量下长时间使用，以免
造成产品异常和听力损伤；
2. 使用中若发现有异常（如冒烟、异味等），请立即关闭电源开关
并拔掉电源插头，然后将产品送经销商检修；
3. 本产品及附件都应放置在室内干燥通风处，勿长期存放在潮湿、
灰尘多的环境，使用中避免靠近火源、雨淋、进水、过度碰撞、
抛掷、振动本机及覆盖通风孔，以免损坏其功能；
4. 若产品需要固定于墙壁或天花板上时，请确保固定到位，防止因
固定强度不足导致产品发生跌落危险；
5. 使用该产品时需遵守相关安全规定，法律法规明确禁止使用场合
请勿使用本机，以免导致意外事故；
6. 请不要自行拆机改装或维修，以防止出现人身伤害，如有问题或
服务需求请联系当地经销商跟进处理。
安全警示
额定功率：500W(AES)
阻抗：8Ω
频率响应：60Hz-19kHz（±3dB）
灵敏度：95dB
覆盖角度：H100°×V 55°
最大声压级：120dB
分频模式：无源二分频
分频点：2300Hz
吊挂／安装：多点吊挂/支架（可旋转调整）
接线方式：1×NL4喇叭连接器，连接1+、1-使用
箱壳：15厘中纤板
表面处理：黑色催化聚亚安酯漆
高频：1.4″×1（36芯，26mm喉口）90磁钢
低频：10″×1（50芯），145磁钢
规格（mm）：320×320×520（W×D×H）
技术参数
注：以上数据由得胜实验室测试得到，并拥有最终解释权！

Welcome to use EKS-101, the built-in 2 way full range speaker
which adopts plane wave guide technology for overlapping
phase delay transmission and the converted sound wave phase,
high sensitivity, clear and charming tone, wide and natural
range to suit for multifunction hall, conference hall, bar, KTV.
Please read the user manual for better operation and keep it
for reference in future.
Speaker Cabinet Series User Manual
EKS-101
Features
EKS-101 consists of one 10 inch cone woofer and one 36 mm
tweeter. The tweeter uses PEEK diaphragm and CCA voice coil.
The woofer uses refractory glass fiber bobbin and 50mm CCA
winding voice coil for high efficiency and reliable performance,
and symmetric magnet to reduce second harmonic distortion.
The crossover components use extremely low consumption
OFC inductor and high quality polyethylene capacitor to
reduce the sound quality loss.
Refractory Peek diaphragm is durable and anti-erosive and
keeps excellent mechanical performance in 250°C during long
time operation.
15mm MDF trapezoidal enclosure eliminates standing wave
inside, black painting finish for anti-moisture, handle for easy
transportation, Al socket for pole mounting, multiple flying
points for flexible applications.
Specification
Rated power: 500W(AES)
Impedance: 8Ω
Frequency response: 60Hz-19kHz (±3dB)
Sensitivity: 95dB
Coverage: H100°×V 55°
Max SPL: 120dB
Crossover mode: 2 way passive
Crossover frequency: 2300Hz
Suspension/installation: multiple flying points/pole
mounting(adjustable angle)
Connection: 1×NL4 speaker connector, connect 1+, 1- for
operation
Cabinet: 15mm MDF
Finish: black painting
HF: 1.4"×1 (36mm, 26mm throat) 90 magnet
LF: 10"×1 (50mm), 145 magnet
Dimension (mm): 320×320×520 (W×D×H)
Application
Multi-function hall, conference hall, bar or KTV
Product Content
EKS-101 speaker cabinet
User manual
Caution
1. Used with TAKSTAR EKA-3A power amplifier together.
2. Ensure to match the power and impedance of power
amplifier and speaker cabinet. The unbalanced
configuration leads to equipment damage or bad sound
effect.
3. Do not put objects on the cabinet due to the severe
vibration amplitude of the speaker cabinet.
4. Ask professional technician for reliable installation in a
place hard to touch.
5. Handle with care during transportation to avoid speaker
cabinet Damage.
Note: the above data is obtained from the test of Takstar
laboratory, and has the final interpretation right!
Safety instruction
In order to avoid possible personal injury or property
damage caused by electric shock, high temperature, fire,
radiation, explosion, mechanical hazards and improper use,
please read and observe the following items carefully before
using the product.
1. When using the product, please confirm whether the power
of the connected device matches the power of the product,
and adjust the volume of the device. Do not use it for a long
time when the power of the product is exceeded or at a high
volume to avoid product failure and hearing damage.
2. If there is any abnormality (such as smoke, odor, etc.)
during use, please turn off the power switch and unplug the
power plug immediately, and then send the product to the
dealer for maintenance.
3. The product and accessories should be placed indoors in a
dry and ventilated place. Do not store them in a humid and
dusty environment for a long time. Avoid getting close to
fire, rain, water, excessive collision, throwing, vibrating the
machine and covering the ventilation holes during use, so
as not to damage its function.
4. If the product needs to be fixed on the wall or ceiling, please
make sure to fix it in place to prevent it from falling down.
5. When using the product, you must abide by the relevant
safety regulations. Please do not use the product in the
occasions that are clearly prohibited by laws and
regulations to avoid accidents.
6. Please do not disassemble, refit or repair the product by
yourself to prevent personal injury. If you have any
questions or service needs, please contact the local dealer
for follow-up.