Talkaphone VOIP-500 Series User manual

VOIP-500 Series Emergency Phone Quick Installation Guide
Copyright 2010 Talk-A-Phone Co. All rights reserved.
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 1 of 6
Phone [phone] • Fax [phone] • [e-mail] • www.talkaphone.com
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
I. Introduction
This Quick Installation Guide provides instructions for installation of the VOIP-500 Series
Emergency Phone. It is recommended to read this instruction set completely before starting
any installation.
II. Contents
The VOIP-500 Series Emergency Phone, Figure 1, includes:
QTY
Part Number
Description
1
VOIP-500
VOIP-500 Phone Assembly
6
42867
10 -24 Tamper Resistant Screws
1
86392
Ferrite Core
Figure 1. Front view

VOIP-500 Series Quick Installation Guide
Copyright 2010 Talk-A-Phone Co. All rights reserved.
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 2 of 6
Phone [phone] • Fax [phone] • [e-mail] • www.talkaphone.com
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
III. Field Wiring Installation
1. Remove and set aside the VOIP-500 Series Emergency Phone Assembly.
2. Remove the back box from the VOIP-500 Series Emergency Phone Assembly by
unfastening the six (6), #6-32 nuts and washers.
3. For PCB (Printed Circuit Board) wiring details, refer to Figure 2.
Figure 2. Internal PCB (Printed Circuit Board) view
IV. Power
Power over Ethernet (PoE)
1. Connect the Network (Ethernet) cable to the “WAN Ethernet” port on the PCB, as shown
in Figure 2. Nominal draw of the phone in PoE mode is 150mA (+36-57 VDC).
2. When installing the Network cable, it is essential to have a ferrite core provided with the
phone, installed on to the cable as close as possible to the phone. Make sure, the
network cable is passed twice through the ferrite core, forming a loop of not less than one
(1) inch in diameter.
A Cat5e or higher cable with RJ45 connector is typical for all network cables.

VOIP-500 Series Quick Installation Guide
Copyright 2010 Talk-A-Phone Co. All rights reserved.
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 3 of 6
Phone [phone] • Fax [phone] • [e-mail] • www.talkaphone.com
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
Figure 3. Installation of the ferrite core on the network cable
Local Power
1. If PoE is not available, connect 12 VDC (500-800mA), 24 VDC (300-500mA) or 24 VAC
(300-500mA), to the 2-pin “Power Supply Input” removable connector plug to the, as
shown in the Figure 2. By default the phone is setup for 24 VDC/24 VAC power modes.
NOTE: Dedicated line regulated power supply required.
2. For 12 VDC power mode, place the internal jumpers on the two outermost terminals as
shown in Figure 4.
3. For 24 VDC/ 24VAC power modes, place the internal jumper on the two innermost
terminals as shown in Figure 4.
Use a two conductor, No. 24 to 12 AWG cable size for power connections.

VOIP-500 Series Quick Installation Guide
Copyright 2010 Talk-A-Phone Co. All rights reserved.
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 4 of 6
Phone [phone] • Fax [phone] • [e-mail] • www.talkaphone.com
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
Figure 4. Internal Jumper position for optional power modes (phone default setting is 24
VDC / 24 VAC)
V. Ground
The faceplate of the phone must be connected to earth ground. Install a #10 ring terminal to the
ground wire before connecting it to the earth grounding terminal on the rear of the faceplate as
shown in Figure 2.
VI. Auxiliary Input/Output
1. The VOIP-500 Series Emergency Phone has three (3) Auxiliary Inputs (dry contact,
10mA @ 8VDC) and three (3) Auxiliary Outputs (dry contact, 120mA @ 120VAC/DC).
The Auxiliary Output allows the peripheral equipment such as strobe lights, PTZ
cameras, door entry systems etc. to be activated when the push button is pressed.
2. Two (2) removable 6-pin connector plugs are provided for the auxiliary input and output
as shown in the Figure 5.
3. The Auxiliary Input and Auxiliary Output connections are as follows:
Auxiliary Connection
Connector Plug Pin Position
Aux. Input 1
Position 7 and 8
Aux. Input 2
Position 9 and 10
Aux. Input 3
Position 11 and 12
Auxiliary Connection
Connector Plug Pin Position
Aux. Output 1
Position 1 and 2
Aux. Output 2
Position 3 and 4
Aux. Output 3
Position 5 and 6

VOIP-500 Series Quick Installation Guide
Copyright 2010 Talk-A-Phone Co. All rights reserved.
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 5 of 6
Phone [phone] • Fax [phone] • [e-mail] • www.talkaphone.com
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
Use a two conductor, No. 28 to 16 AWG cable size for all auxiliary connections.
Figure 5 Auxiliary Input/Output and Power connectors
VII. Line Level Audio
Connect a 3.5 mm plug to the “Line Level Audio” Connector on the PCB, as shown in the
Figure 2, to the respective device on the other end, such as the WEBS®paging amplifier,
recording device, speaker, etc. The 3.5 mm audio plug is included with the WEBS-MT/R,
WEBS-WM and the WEBS-PM installation kits.
After all the field wiring installation, fasten the back box on to the faceplate with the six (6)
hardware nuts and washers.
NOTE: It is the installer’s obligation to ensure that the wiring should pass through the cable
entry hole at the bottom of the back box. Please exercise caution when reinstalling the back
box and ensure that no cables are crushed during the process.

VOIP-500 Series Quick Installation Guide
Copyright 2010 Talk-A-Phone Co. All rights reserved.
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 6 of 6
Phone [phone] • Fax [phone] • [e-mail] • www.talkaphone.com
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
Figure 6. Installation of VOIP-500K into ETP-SM
Install the VOIP-500 Series Emergency Phone into its appropriate mount (e.g. ETP-SM, as
shown in Figure 6), with the six (6) tamper resistant faceplate screws provided. A #10 tamper
resistant screwdriver (Talk-A-Phone Model No. 42834D) or bit (Talk-A-Phone Model No.
42834B), is recommended for installation.