Tandberg Data REPLACE TAPE DRIVE IN T24 OR T48 User manual

Copyright 2006 Tandberg Data and Exabyte, EZ17, M2, VXA, and VXAtape are registered trademarks; ExaBotics, MammothTape, and SmartClean are
trademarks; SupportSuite is a service mark. Linear Tape-Open, LTO, the LTO Logo, Ultrium and the Ultrium Logo are trademarks of HP, IBM, and Quantum in
the US and other countries. All other product names are trademarks or registered trademarks of their respective owners.
433680-01 October 2006 www.tandberg.com
INSTALLING ATAPE DRIVE IN
This document explains how to install or replace a tape drive in the Tandberg
StorageLibrary T24 or Tandberg StorageLibrary T48. Please read the entire section that
you are using prior to beginning the procedure.
PREPARING FOR INSTALLATION OR REPLACEMENT
Note: If your library is installed in a rack, it is not necessary to remove the library from the
rack to complete this procedure. It is also not necessary to disconnect the Ethernet
cable from the back of the library.
Obtain these items—a #2 Phillips screwdriver and a small flat-blade screwdriver.
Ensure that the environment is free of conditions that could cause electrostatic
discharge (ESD)—If possible, use an antistatic mat and a grounded static protection
wristband during installation. If a mat and wristband are not available, touch a known
grounded surface, such as a computer’s metal chassis.
Warning Before performing any installation or maintenance procedures, be
sure that the library’s power switch is off and that the power cord is
disconnected from the library and the outlet.
Warnung Vor der Ausführung von Installations- oder Wartungsarbeiten ist
darauf zu achten, daß der Library-Netzschalter auf “Aus” gestellt ist
und daß das Anschlußkabel vom Library und der Steckdose entfernt
ist.
Advertencia Antes de realizar cualquier procedimiento de instalación o de
mantenimiento, comprobar que el interruptor de alimentación de la
biblioteca está apagado y que el cable de alimentación no está
enchufado ni a la biblioteca ni a la toma de corriente.

2 OF 28
GENERAL INFORMATION
Both the StorageLibrary T24 and StorageLibrary T48 Library accommodate Ultrium 3
(LTO-3) or Ultrium 2 (LTO-2) tape drives in half height (HH) or full height (FH)
configurations. Neither library will accommodate LTO-1 tape drives.
Note: Most of the illustrations show SCSI configurations. Use the same steps to install Fibre
Channel tape drives.
Information that is specific to the individual libraries is indicated as follows:
StorageLibrary T24—One full height tape drive or two half height tape drives
StorageLibrary T48—One or two full height tape drives, or one, two, three, or four half
height tape drives
! Important The tape drives must be specially configured (at the factory) for use in a
StorageLibrary T24 or StorageLibrary T48 library. Purchase tape drive
kits only from Tandberg Data or Tandberg-approved suppliers.
To view this information... go to...
Installing additional tape drives page 8
Replacing a tape drive with the same configuration
(half height -to- half height or full height -to- full height)
page 14
Replacing a half height tape drive with a full height tape drive page 19
Reconfiguring the library
(this step must be completed for the library to operate)
page 25
Resuming operation page 26
Confirming the installation page 28

3 OF 28
REFERENCE ILLUSTRATIONS
StorageLibrary T24—
! Important Be sure to use the serial cable (C) that came with your replacement
kit. The serial cables are specifically configured (at the factory) for use
with the individual tape drives.
Lower SCSI
cover plate (S)
Upper SCSI
cover plate (S)
StorageLibrary T24
Half Height
Tape Drive
Cover Plate (P)
StorageLibrary T24
Full Height
Tape Drive
Cover Plate (P)
StorageLibrary T24
Full Height
Fibre Channel
Tape Drive
Cover Plate (P)
Serial cable (C)
Connect to
library (black)
Connect to
tape drive (white)

4 OF 28
Figure 1 StorageLibrary T24 serial cable routing—full height tape drive
Figure 2 StorageLibrary T24 serial cable routing—half height tape drives
Figure 3 StorageLibrary T24 power cable routing—full height tape drive
Figure 4 StorageLibrary T24 power cable routing—half height tape drives
Serial cable (C)
Bottom serial
connector
Top serial
connector (not used)
Drive 1
Drive 2
Bottom serial
connector
Second serial
connector
Drive 1
Drive 2
Power cable (D)
Library power
connector
Middle power connector
Bottom power
connector
(not used in this
configuration)
Power cable (D)
Library power
connector
Middle power
connector (lower TD)
Top power
connector (upper TD)
Serial cable ( C )

5 OF 28
StorageLibrary T48—
! Important Be sure to use the serial cable (C) that came with your
replacement kit. The serial cables are specifically configured
(at the factory) for use with the individual tape drives.
StorageLibrary T48
Tape Drive
Half Height
SCSI cover
plate (S)
SCSI cover
plate (S)
SCSI configuration
Cover Plate (P)
Full Height
Fibre Channel
StorageLibrary T48
Tape Drive
Cover Plate (P)
configuration
Serial cable (C)
Connect to
Connect to tape
library (black)
drive (white)

6 OF 28
Figure 5 StorageLibrary T48 serial cable routing—full height tape drives
Figure 6 StorageLibrary T48 serial cable routing—half height tape drives
Serial cable (C)
Bottom serial
connector
Third serial
connector (not used)
Second serial
connector
Top serial
connector (not used)
Drive 1
Drive 2
Drive 3
Drive 4
Serial cable (C)
Bottom serial
connector
Third serial
connector
Second serial
connector
Top serial
connector
Drive 1
Drive 2
Drive 3
Drive 4

7 OF 28
Figure 7 StorageLibrary T48 power cable routing—full height tape drives
Figure 8 StorageLibrary T48 power cable routing—half height tape drives
Power cable (D)
Library power
connector
Top power connector
(not used in this
configuration)
Second power connector
(not used in this
configuration)
Bottom power
connector
Third power connector
Power cable (D)
Library power
connector
Bottom power
connector
Third power
connector
Second power
connector
Top power
connector

8 OF 28
INSTALLING ADDITIONAL TAPE DRIVES
To install an additional tape drive (or tape drives), follow these steps:
1. Preparing for replacement—
a. Power off the library (press the 0on the back of the unit)
b. Disconnect the power cord, the SCSI or Fibre Channel cable(s), and the terminator
(if one is installed).
c. Power off the host
d. Remove the tape drive cover plate (P). Set the plate and the screws aside.
Note: This figure shows the StorageLibrary T24 SCSI library with one half height tape
drive installed. Remove the StorageLibrary T48 tape drive cover plate (SCSI and
Fibre Channel) the same way.
2. Removing the internal cooling plates and disconnecting cables—
Figure 9 Tape drive cover plate (StorageLibrary T24 library shown)
! Important Remove as many internal cooling plates as necessary to add
tape drives, but leave all empty tape drive bays covered. The
plates are required for proper cooling.
Power OFF
Disconnect
power cord
Tape drive
cover plate (P)
Screws
(press the 0)
Back of library
Screws

9 OF 28
a. Remove the two screws (A) holding the tape drive cooling plate (B). Remove the
plate, and discard it and the screws.
b. Disconnect the power cables (D) from all of the tape drives.
3. Installing the tape drive—
a. Locate the serial cable (C) that came in your replacement kit and attach it to the
appropriate serial connector inside the library.
StorageLibrary T24 library serial cable connections—
Half height tape drive—see Figure 2
Figure 10 StorageLibrary T24 tape drive cooling plate
! Important Do not mix full height and half height or SCSI and Fibre
Channel tape drives in the StorageLibrary T48 library, as it does
not support mixed tape drive configurations.
Tape drive Quantity Install in this
opening...
Serial
connector
Internal
label
Half height Second tape drive Top Top Drive 2
Single tape drive Bottom Bottom Drive 1
Screws (A)
Retaining
Cooling plate (B)
Single half height
tape drive (cables
removed for
tab
clarity)
Looking inside
back of library

10 OF 28
StorageLibrary T48 library serial cable connections—
Full height tape drive—see Figure 5
Half height tape drive—see Figure 6
b. While holding the cables to the side, slide the new tape drive directly into the library,
leaving it a short distance out to access the cables. Use care not to damage the cables.
c. Connect the supplied serial cable (C) and the power cable (D) to the tape drives.
StorageLibrary T24 tape drive serial and power cable connections—
Serial—Route the serial cable (C) over the tape drive carrier and under the power
cable as shown here; connect as shown in Figure 2 (StorageLibrary T24 HH serial
cable routing).
Power—Route the power cable through the tape drive carriers as shown here;
connect as shown in Figure 4 (StorageLibrary T24 HH power cable routing).
Tape drive Quantity Install in this
opening...
Serial
connector
Internal
label
Half height
Fourth tape drive Top To p D riv e 4
Third tape drive Third Third Drive 3
Second tape drive Second Second Drive 2
Single tape drive Bottom Bottom Drive 1
Full height Second tape drive Top Second Drive 2
Single tape drive Bottom Bottom Drive 1
Figure 11 StorageLibrary T24—installing additional tape drives: half height connectors
Power cable (D)
Serial cable (C)
Tape drive
(route over
carrier and
under the
power cable)
(route under carrier
and over serial cable)
carrier
Press the serial cable (C) down into the
carrier to prevent catching it between
the tape drive and the library.