Taramp's Tarsafe TMV 307 User manual

TMV 307
Instruction manual

01
1 2 3
TMV 307
- Connection compatible with most of the main electric windows kits on the market.
- Anti-crushing system, in compliance with CONTRAN (national traffic council) resolution, No. 468 OF 2013;
- Opens the windows through the auxiliary alarm signal;
- Closes the windows through the alarm signal, turning lights or lock, with pulse or negative level;
- Smart window opening and closing, with just 1 touch on the window button;
- Interrupts the smart closing when turning off the ignition or pressing the window button;
- Alternating pressure relief. Open the window + - 5 cm when opening the door, and close the window
when closing the door;
- Central for conventional buttons (high current reversible with negative rest), low current positive pulse
(GM), Resistive (VW and FIAT);
- 1 minute Timer after turning off the ignition;
- Volkswagen and FIAT rear window lock activated by the original button;
- Transformation of the LOCK and UNLOCK signal of the original VW button into a signal for the universal
electric lock kit.
Note: CONVENTIONAL, COMMON, or REVERSIBLE button, it is the button that is directly connected to
the electric window engine. For this type, all JUMPERS must be removed.
You must do the JUMPERS setting before connecting the TMV 307 control unit to the harness,
according to the type of button.
Technical Features:
ATTENTION:
CONVENTIONAL BUTTONS OR
LOW CURRENT GM
RESISTIVE BUTTONS
RESISTIVE BUTTONS
RESISTIVE BUTTONS
JUMPER SETTING
1 - Connect all wires;
4 - Program the anti-crush function.
2 - Set the Jumpers according to the type of BUTTON;
Installation sequence:
3 - Connect the control unit to the harness;
3 - With the windows closed, keep the 2 buttons (driver and passenger) activated to close the windows
until the automatic setting starts.
Anti-crush setting:
The setup process is done in one window at a time, fully opening and closing it. At the end, the 2 windows
will be closed. If any of them remain open, it indicates that the system has not been set correctly and the
process must be repeated.
2 - Close the windows with short touches on the buttons, if they are open;
1 - Switch on the ignition;
If the setting failure persists, check the installation and especially the voltage of the supply that goes to the
TMV, if there is a very large drop in voltage, the system will not be set correctly.
WITHOUTUT JUMPER
WITHOUTUT JUMPER
WITHOUTUT JUMPER
WITHOUTUT JUMPER
WITH JUMPER
WITH JUMPER
WITH JUMPER
WITH JUMPER
WITH JUMPER
WITH JUMPER
WITH JUMPER
WITHOUTUT JUMPER
VW REAR

02
18
916
GR/BR - close
BR/BR - close
YL/BR - open
GR/WH - thin
Door switch
GR/BK - thin
Close window signal
GR - thin
Open window
PP/BR - open
-
1
BL- thin
+12V Post-Ignition
BR - Thin
Lighting
Common or GM
Common button or GM Common button or GM
Closed windows Hold press ed to clo se the
windows until setting initiates
+=at the end 2 windows
closed= OK
IGNITION
ON
START
OFF
IGNITION
ON
START
OFF
+
+
Close windows from both doors through the button
The setting will be done1 window
at a time, closing and opening.
++

03
FIAT - Rear resistive button
VM/PT - thin
buttons GND
18
916
GR/WH- close
BR/WH- close
YL/WH- open
GR/WH- thin
Door switch
GR/BK- thin
Close window signal
GRAY - thin
Open window signal
PP/WH - open
-
-
-
BL- thin
+12V Post-Ignition
LED BLOCK
GND
+12 V
BLOCK.
RL
RR
Driver door connection
1
BR - thin
lighting

04
18
916
Resistive Button FIAT
Resistive Button FIAT
FIAT - Front Resistive Button
GR/WH - close
BR/WH - close
YL/WH- open
GR/WH - Thin
Door switch
GR/BK - thin
Close window signal
GRAY- thin
Open window signal
PP/WH - open
-
-
-
1
1
BL- Thin
+12V Post-Ignition
RD/BK- Thin
Buttons GND WH- thin
Lighting

05
WH- thin
lighting
Button coneection
Window Lock
VW - Rear resistive button
RD/BK- thin
Buttons GND
18
916
GR/WH - close
BR/WH- close
YL/WH- open
GR/WH- thin
Door Switch
GR/BK- thin
close window signal
GRAY- thin
Open window signal
PP/WH - open
-
-
-
BL- thin
+12V post-ignition
Button
on the panel
Button
on the panell
1

06
GR/WH - close BR/WH- close
YL/WH - open
GR/WH - thin
Door Switch
GR/Bk- thin
close window signal
GRAY- thin
Open window switch
PP/WH- open
-
1
1
8
916
BL- thin
+12V post-ignition
Lock/unlock
button
Electric lock
kit
RD/BK
lock signal
BR
unlock signal
WH - thin
lighting
VW - Front resistive button

MN_014171_R03
Taramps reserves the right to change the content of this manual without prior notice or
obligation to apply the modifications to previously produced units.
Factory technical support department:
Phone numbers: (18) 3266-4050 / 99749-3391
E-mail: [email protected]
Taramps Electronics: nº 274 Abílio Daguano street, - ZIP: 19.180-000
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121• Res. Manoel Martins
Alfredo Marcondes - SP
Indústria Brasileira - Made in Brazil
Warranty Terms
•Costs of removal and reinstallation of the equipment, as well as its transport to the technical assistance
post;
•Damages of any kind, resulting from problems with the product, as well as losses caused by
discontinuation of use
•Products damaged by incorrect installation, water infiltration, tampering by unauthorized persons;
• Scratched or torn warranty seal;
•Natural wear components, such as batteries and others;
TARAMPS, located at Rua Abílio Daguano, 274 Res. Manoel Martins - Alfredo Marcondes - SP, ZIP
19.180-000, guarantees this product against design, manufacturing, assembly and/or joint and several
defects due to design flaws that make it inappropriate for its intended use, for a period of 24 months from
the date of purchase.
•Malfunction caused by accessories, modifications or equipment attached to the product;
This warranty excludes:
In the event of a defect within the warranty period, TARAMPS' liability is limited to repairing or replacing
the device manufactured by it.
•The product presents damage resulting from drops, impacts or the action of agents of nature (floods,
lightning, etc.);
•Cases where the product is not used under regular conditions;