Tascam US-200 User manual

US-200
USB 2.0 Audio/MIDI Interface
D01139820A
OWNER'S MANUAL
Before connecting this unit to a computer, you must install
the dedicated driver from the included CD-ROM onto the
computer.

2TASCAM US-200
IMPORTANT SAFETY INFORMATION
Do not expose this apparatus to drips or
•
splashes.
Do not place any objects filled with
•
liquids, such as vases, on the apparatus.
Caution should be taken when using
•
earphones or headphones with the
product because excessive sound pressure
(volume) from earphones or headphones
can cause hearing loss.
Declaration of Conformity
Model Number: US-200
Trade Name: TASCAM
Responsible party: TEAC AMERICA, INC.
Address: 7733 Telegraph Road, Monte-
bello, California, U.S.A.
Telephone number: 1-323-726-0303
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
This appliance has a serial number located on the
bottom panel. Please record the model number and
serial number and retain them for your records.
Model number
Serial number
FOR U.S.A.
TO THE USER
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures.
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment
and receiver.
c) Conn ect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
d) Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
Changes or modifications to this equipment not
expressly approved by TEAC CORPORATION for
comp liance could void the user's autho rit y to
operate this equipment.

TASCAM US-200 3
For European Customers
ª
Disposal of electrical and electronic
equipment
(a) All electrical and electronic equipment
should be disposed of separately from
the municipal waste stream via collection
facilities designated by the government
or local authorities.
(b) By disposing of electrical and electronic
equipment correctly, you will help save
valuable resources and prevent any
potential negative effects on human
health and the environment.
(c) Improper disposal of waste electrical
and electronic equipment can have
serious effects on the environment and
human health because of the presence of
hazardous substances in the equipment.
(d) The Waste Electrical and Electronic
Equipment (WEEE) symbol, which shows
a wheeled bin that has been crossed out,
indicates that electrical and electronic
equipment must be collected and
disposed of separately from household
waste.
(e) Return and collection systems are
available to end users. For more detailed
information about the disposal of old
electrical and electronic equipment,
please contact your city office, waste
disposal service or the shop where you
purchased the equipment.
Safety Information

4TASCAM US-200
Table of Contents
1 – Introduction ...................................5
Main features.................................................. 5
Product parts.................................................. 6
Manual conventions.................................... 6
Trademarks...................................................... 6
Cautions on installation ............................. 7
Beware of condensation ............................ 7
Cleaning the unit .......................................... 7
2 − Names and Functions of Parts ......8
Front panel...................................................... 8
Rear panel......................................................10
3 − Installation ...................................12
System requirements ................................12
Windows.................................................12
Mac OS X ................................................12
Installing the driver and control panel12
Installing the driver and control
panel for Windows..............................13
Installing the driver for Mac OS X..14
Uninstalling the driver.......................15
Frequently asked installation
questions and answers (FAQ)..........15
Improving computer performance......16
Cubase LE 5 installation ...........................16
4 – US-200 control panel settings.....17
Overview........................................................17
Control panel menus and settings.......17
Audio Performance ............................17
LINE OUTPUTS 1/2 and LINE
OUTPUTS 3/4 ........................................18
5 – Connections..................................19
USB connections.........................................20
Audio connections.....................................20
Microphones ........................................20
Guitars.....................................................21
Connecting keyboards, drum
machines, sound modules,
cassette/MD/CD players and other
analog line level devices ..................21
Analog record player .........................21
Line input devices, including
MD/CD recorders and effect
boxes .......................................................21
Monitor speakers ................................21
Headphones .........................................21
Connecting MIDI devices ........................21
6 – Application Guide........................22
Cubase LE 5...................................................22
Windows XP and Windows Media
Player...............................................................22
Windows Vista or Windows 7 and
Windows Media Player..............................22
Mac OS X and iTunes .................................23
7 – MIDI implementation chart.........24
8 – Troubleshooting...........................25
9 – Specifications ...............................28
AD/DA audio converter............................28
Analog audio inputs ..................................28
Analog audio outputs...............................28
Control I/O.....................................................28
Audio performance....................................28
Computer requirements ..........................29
Windows.................................................29
Macintosh ..............................................29
General ...........................................................29
Dimensional drawing................................30

TASCAM US-200 5
1 – Introduction
Thank you for your purchase of the TASCAM
US-200 USB 2.0 Audio/MIDI Interface.
Before connecting and using the unit, please
take time to read this manual thoroughly
to ensure you understand how to properly
set up and connect the unit, as well as the
operation of its many useful and convenient
functions. After you have finished reading
this manual, please keep it in a safe place for
future reference.
You can also download the Owner’s Manual
from the TASCAM web site (http://tascam.
com/).
Please also check the above site for the latest
manual updates.
If any data is lost from another MIDI device,
hard disk, MO disc or other media in the same
system where this unit is used, TASCAM will
bear no responsibility for its recovery, nor will
it provide any compensation for such loss.
Main features
USB 2.0 audio/MIDI interface
•
24-bit/96 kHz audio interface
•
2-channel analog input signals (L, R) can be
•
input at the same time
Two XLR mic inputs (balanced) with high
•
performance microphone preamps
Two standard input jacks (combined with
•
the XLR connectors)
One of the 1/4” phone inputs can be
•
switched to allow direct input (high
impedance) of an electric guitar or electric
bass.
2 unbalanced stereo line outputs (RCA
•
jacks) and a headphone output
Output level from the unbalanced stereo
•
line output and headphones jacks can be
adjusted using a volume knob (same knob
controls both simultaneously)
MIDI IN/OUT
•
Direct Monitor function allows zero-latency
•
monitoring of the input
Inputs 1 and 2 can be set to be monitored
•
as either a stereo pair or as two mono
channels
Input and overload LED indicators included
•
for each input channel
MON MIX knob allows the balance between
•
the input signals and the output from the
computer to be adjusted for monitoring
Power can be supplied from a USB bus,
•
which is convenient for mobile use
Dedicated Windows (Windows XP, Windows
•
Vista, Windows 7) and Macintosh (OS 10.5,
OS10.6) drivers included
USB 2.0 High Speed (480 MHz) compatible
•
Can supply 48 V phantom power to 2 mic
•
inputs
Cubase LE 5 bundle
•
A note about computer operation
If you are unsure about how to perform
basic computer operations appearing in this
manual, please refer to the owner’s manual
that came with your computer.
To use this unit, you must use the included
CD-ROM to install the dedicated driver on
your computer. For details about installation,
see “Installing the driver and control panel” in
“3 – Installation”.

6TASCAM US-200
Product parts
The US-200 package contains the following
items.
Take care when opening the package not
to damage the items. Keep the package
materials for transportation in the future.
Please contact the store where you purchased
this unit if any of these items are missing or
have been damaged during transportation.
Main unit
•................................................................ 1
USB Cable
•.............................................................. 1
CD-ROM (containing drivers)
•......................... 1
DVD-ROM (Cubase LE5)
•.................................... 1
Cubase LE5 Quick Start Guide
•........................ 1
Warranty card
•....................................................... 1
Owner's Manual (this document)
•................. 1
Manual conventions
Buttons, jacks and other parts on the unit
•
and external dvices are indiated like this:
LEVEL.
When we show messages, for example,
•
that appear on the screen, we show them
like this: OK.
Additional information is introduced in the
•
styles below when needed:
TIP
These are tips about how to use the unit.
NOTE
These provide additional explanations and
describe special cases.
CAUTION
Failure to follow these instructions could
result in injury, damage to equipment or lost
recording data, for examaple.
Trademarks
TASCAM is a trademark of TEAC
•
Corporation, registered in the U.S. and
other countries.
Microsoft, Windows, Windows Vista,
•
Windows 7, and Windows Media Player are
either registered trademarks or trademarks
of Microsoft Corporation in the United
States and/or other countries.
Apple, Macintosh, Mac, Mac OS X and
•
iTunes are trademarks of Apple Inc.
Pentium and Intel are trademarks of
•
Intel Corporation in the U.S. and/or other
countries.
AMD Athlon is a trademark of Advanced
•
Micro Devices, Inc.
Cubase is a registered trademark of
•
Steinberg Media Technologies GmbH.
ASIO is a trademark of Steinberg Media
Technologies GmbH.
Other company names, product names and
•
logos in this document are the trademarks
or registered trademarks of their respective
owners.
1 – Introduction

TASCAM US-200 7
Cautions on installation
The unit’s nominal operating temperature
•
is between 5˚ and 35° C (41° – 95° F).
Do not install in the following types of
•
places. Doing so could degrade the sound
quality and/or cause malfunctions.
Places with significant vibrations or that
•
are otherwise unstable
Near windows or other places exposed
•
to direct sunlight
Near heaters or other extremely hot
•
places
Extremely cold places
•
Places with bad ventilation or high
•
humidity
Very dusty locations
•
Make sure that the unit is mounted in a
•
level position for correct operation.
Do not place any object on the unit for
•
heat dissipation.
Avoid installing this unit on top of any
•
heat-generating electrical device such as a
power amplifier.
Beware of condensation
If the unit is moved from a cold to a warm
place, or used after a sudden temperature
change, there is a danger of condensation;
vapor in the air could condense on the
internal mechanism, making correct
operation impossible. To prevent this, or if
this occurs, let the unit sit for one or two
hours at the new room temperature before
using.
Cleaning the unit
To clean the unit, wipe gently with a soft dry
cloth. Do not use any benzene, paint thinner,
ethyl alcohol or other chemical agents to
clean the unit as they could damage the
surface.
1 – Introduction

8TASCAM US-200
2 − Names and Functions of Parts
Front panel
1+48V indicator
This lights when the PHANTOM (+48V)
switch is set to ON.
CAUTION
Do not connect or disconnect microphones
when this indicator is lit.
2USB indicator
This lights when the USB connection is
active.
3OL and SIG indicators
OL (overload) indicators
These light just before the input signal
distorts (when it exceeds −2 dBFS).
SIG (signal) indicators
These light when a signal (of −30
dBFS or more) is input through the
corresponding channel.
4indicator
This lights when the INST/LINE switch is
set to INST.
5MIC/LINE/INST IN 1 (balanced/
unbalanced) connector
Use this connector for balanced analog
XLR microphone input or as a standard
TRS jack. Use the INST/LINE switch on
the rear panel to set the function of this
standard TRS jack to either balanced line
input (LINE) or unbalanced guitar input
(INST).
• XLR (1: GND, 2: HOT, 3: COLD)
• TRS (Tip: HOT, Ring: COLD, Sleeve: GND)
6MIC/LINE IN 2 (balanced) connector
Use this connector for balanced analog
XLR microphone input or as a standard
TRS jack for balanced analog input.
XLR (1: GND, 2: HOT, 3: COLD)
•
TRS (Tip: HOT, Ring: COLD, Sleeve: GND
•
7PHONES jack
Use this standard jack to connect stereo
headphones. Use an adapter to connect
headphones with a miniplug.
CAUTION
Before connecting headphones, turn the
LEVEL knob to minimize the volume. Failure
to do so might cause sudden loud noises,
which could harm your hearing or result in
other trouble.
NOTE
The LEVEL knob also adjusts the line output
level.

TASCAM US-200 9
8LEVEL knob
Use this to adjust the level output from
the LINE OUT 1/2 jacks and the PHONES
jack. This does not adjust the level output
from the LINE OUT 3/4 jacks.
CAUTION
Before connecting headphones, turn the
LEVEL knob to minimize the volume. Failure
to do so might cause sudden loud noises,
which could harm your hearing or result in
other trouble.
9MON MIX knob
Use this knob to adjust the balance
between the signals input through the
unit’s connectors (MIC IN and LINE IN)
and the signal output from the computer
by USB. Turn it all the way to the left
(INPUT) to output and monitor only the
signals input through the unit, and turn
it all the way to the right (COMPUTER) to
output and monitor only the signals sent
from the computer by USB.
0Gain knobs
Use these to individually adjust the input
levels of MIC/LINE/INST IN 1 and MIC/
LINE IN 2 connectors. Turn them all the
way to the left to minimize the level and
all the way to the right to maximize it.
2 − Names and Functions of Parts

10 TASCAM US-200
Rear panel
qLINE OUT 1/2/3/4 (unbalanced) jacks
These RCA pin jacks are unbalanced
analog line outputs.
These jacks can output signals sent
from the computer via USB, signals
from the built-in monitoring mixer or
a combination of both. Use the US-200
software control panel on the computer
to set which signals are output. Connect
these jacks to recorders, speakers with
built-in amplification and external effect
devices, for example.
NOTE
The
•LINE OUT 1/2 jacks can output the
analog signals input through the unit.
The
•LEVEL knob, which also controls the
headphone output, can be used to adjust
the output level of the LINE OUT 1/2
jacks.
The
•LINE OUT 3/4 jacks cannot output
the analog signals input through the unit.
Furthermore, their output levels cannot be
adjusted from the unit.
wMIDI IN jack
This is a standard DIN 5-pin MIDI input
jack.
Use it to input MIDI signals to the
computer connected by USB.
eMIDI OUT jack
This is a standard DIN 5-pin MIDI output
jack.
Use it to output MIDI signals from
the computer connected by USB to a
connected MIDI device.
rST/MONO switch
When monitoring two inputs (MIC/LINE/
INST IN 1 and MIC/LINE IN 2), use this
switch to set it to mono or stereo.
When set to MONO, the two inputs are
mixed, and the mix is sent to both LINE
OUT 1 and 2jacks.
When set to ST, the signal input from
the MIC/LINE/INST IN 1 connector is
output through the LINE OUT 1 jack, and
the signal input from the MIC/LINE IN
2connector is output through the LINE
OUT 2 jack.
When only using the MIC/LINE/INST IN 1
connector input, set this switch to MONO
to monitor the signal through both the
LINE OUT 1 and LINE OUT 2 jacks.
tINST/LINE switch
Set this switch according to the input
connected to the MIC/LINE/INST
IN 1 connector. Set it to INST when
directly connecting an electric guitar or
electric bass guitar, for example. Set it
to LINE when connecting an electronic
instrument or audio equipment, for
example.
2 − Names and Functions of Parts

TASCAM US-200 11
yUSB port
Use the included USB cable to connect
this unit to a USB 2.0-compatible
computer.
NOTE
The US-200 obtains power from the host
•
computer via the USB cable. In rare cases,
a computer’s USB port may not be able to
supply enough power to operate the US-
200.
This is not compatible with USB 1.1 (12
•
MHz) and cannot be used to connect by
USB 1.1.
This is not compatible with computer
•
Suspend (Sleep) mode. For this reason,
the unit might not operate properly after
a connected computer is brought out of
Suspend (Sleep). In this case, disconnect
the USB cable once and then reconnect it.
uPHANTOM (+48V) switch
Use this switch to provide +48 V phantom
power to microphone input connectors 1
and 2.
CAUTION
Set this switch to
•OFF before turning
this unit’s power on or off (connecting or
disconnecting the USB cable).
Before changing the setting of this switch
•
to ON or OFF, turn the LEVEL knob to
its minimum level. Depending on the
microphone connected, a loud noise could
occur, which might damage equipment or
harm hearing.
Do not connect or disconnect
•
microphones when this switch is set to
ON.
Turn this switch on only if you are using
•
condenser microphones that require
phantom power.
Unbalanced dynamic microphones should
•
never be connected to phantom-powered
connectors.
Some ribbon mics can be damaged by
•
phantom power. If unsure, do not supply
phantom power to a ribbon mic.
When this switch is
•ON, if the unit is
connected to a computer running on
battery power, the battery will be drained
more quickly.
Do not use phantom power when line
•
level equipment is connected to an XLR
connector.
2 − Names and Functions of Parts

12 TASCAM US-200
3 − Installation
System requirements
See the TASCAM website (http://tascam.
com/) for updated information about OS
compatibility.
Windows
Supported operating systems:
Windows XP 32-bit SP3 or later
Windows XP 64-bit SP2 or later
Windows Vista 32-bit SP2 or later
Windows Vista 64-bit SP2 or later
Windows 7 32-bit
Windows 7 64-bit
Supported computer systems:
Windows compatible computer with a USB
2.0 port
CPU/clock speed:
Pentium 4 1.0 GHz or faster
AMD Athlon 1.0 GHz or faster
(or equivalent processor)
Memory:
1 GB or more
NOTE
Although this product has been checked
for use with typical computers that meet
the above operating requirements, we
cannot guarantee that it will operate with all
computers that meet these requirements.
Please be aware that even in the same
conditions, computer processing capabilities
can vary depending on differences in design
and specifications.
Mac OS X
Supported operating systems:
Mac OS X 10.5.8 or later
Mac OS X 10.6.3 or later
Supported computer systems:
Apple Macintosh equipped with a USB port
CPU:
Any Mac with an Intel processor, or PPC G4
1 GHz or faster
Memory:
1 GB or more
Installing the driver and
control panel
In order to use this unit, you must install the
driver on to your computer. As described
below, this is an easy process using the CD-
ROM included with the unit.
Drivers are updated from time to time. You
can download the most recent version of
the driver from the TASCAM website (http://
tascam.com/).
Disconnect the unit from the computer
before starting driver installation.
CAUTION
Handle the enclosed CD-ROM with care.
•
If the disc becomes scratched or dirty,
a computer might not be able to read
it, making installation of the software
impossible. If the included disc becomes
unreadable, it can be replaced for a fee.
Never attempt to play the enclosed CD-
•
ROM in an ordinary audio CD player, as
the resulting noise could damage the
speakers or harm your hearing.

TASCAM US-200 13
Installing the driver and control
panel for Windows
NOTE
During driver installation, a warning that
•
“this software ... has not passed Windows
Logo testing“ will appear.
This message appears when installing a
driver that has not received Windows Logo
testing.
This message appears because the drivers
for TASCAM products have not undergone
Windows Logo testing. We have, however,
confirmed their proper operation.
When this message appears, click
Continue anyway or Install to continue the
installation.
During installation, you must connect the
•
unit in step 7. You should complete the
installation step in less than one minute.
Installation may fail if you take too much
time.
Installation on a Windows computer
1 Confirm that the unit and the PC are not
connected by a USB cable.
2 Insert the included driver installation
CD-ROM into the PC where you will
install it.
3 Click the Install Driver button when the
screen below appears. (If this sreen
does not appear automatically, find and
open the Autorun2.exe program in the
Autorun folder on the driver CD-ROM.)
4 When the language selection screen
(below) appears, select the language
you prefer and then click the OK button.
5 Click the Install the driver button when
the screen below appears.
6 Read the contents of the License
Agreement, and select I accept the
agreement if you agree to the terms.
Next, click the Install button to start
installation.
7 When the screen below appears, use
the supplied USB cable to connect the
unit to the PC.
3 − Installation

14 TASCAM US-200
Computer
USB
8 Installation of the driver proceeds.
9 When the screen below appears, the
installation is complete. Click the
Reboot now button to restart the PC to
use the driver.
10 After the PC has restarted, open the
TASCAM US-200 (Start > Control Panel) or
US-200 Control Panel (Start > All Programs
> TASCAM). If the Driver Version, Device
and other data appear correctly, the
installation has succeeded.
Installing the driver for
Mac OS X
1 Confirm that the US-200 is not
connected to the computer.
2 Double-click the TASCAM_US200_
Driver_1.00.dmg on the included CD-
3 − Installation

TASCAM US-200 15
ROM. The TASCAM_US200_1.00.mpkg" is
created on the desktop.
3 Dboule-click the TASCAM_US200_1.00.
mpkg on the desktop to launch the
installer.
4 Follow the instructions on the screen to
conduct the installation.
5 Restart the computer and then connect
the unit.
Uninstalling the driver
Windows
ª
There are two ways to uninstall the driver as
shown below.
Using the Installation CD-ROM:
1 Follow steps 1 to 4 under“Installing the
driver and control panel for Windows”
(See page 13.)
2 At step 5 of the procedure, click Remove
the driver.
3 Follow the instructions on the screen
for the remaining procedure.
Using Windows“Add or Remove Programs”
1 Open the Control Panel from the Start
menu.
2 Double click on Add or Remove programs.
3 Select US-200 driver from the list and
click Change or Remove Programs.
4 Follow the instructions on the screen
for the remaining procedure.
Mac OS X
ª
1 Insert the CD-ROM into the computer,
open TASCAM_US200_Driver_1.00.dmg
and double click TASCAM US-200 remover
icon.
2 Follow the instructions on the screen
for the remaining procedure.
Frequently asked installation
questions and answers (FAQ)
Windows driver installation
Q: When I connect the unit to a computer,
the Windows Hardware Wizard appears
and I cannot install the driver. Am I
making a mistake during the installation
procedures?
A: Close the Windows “Hardware Wizard” and
disconnect the unit. You must install the
driver before connecting this unit. Insert
the CD-ROM included with the product.
The menu for installing the driver appears
automatically.
Select Install Driver, and follow the
instructions shown on the screen. If you
have downloaded the driver from the
TASCAM website (htt://tascam.com/),
expand the ZIP archive, launch the setup.
exe file, and follow the instructions on the
screen.
Q: I loaded the installation CD-ROM into
a Windows computer, but the driver
installation menu does not appear. How
can I access this menu?
A: The automatic playback settings for the
disc drive might be disabled.
3 − Installation

16 TASCAM US-200
Open the supplied driver CD-ROM using
Windows Explorer, and double-click the
Autorun2.exe file to manually open the
installation menu.
Follow the procedures in “Installing the
driver and control panel for Windows”on
page 13 to install the driver.
Improving computer
performance
In this manual, we will offer only the
following basic tip to improve performance
when using this unit.
Do not run other applications.
Processing digital audio places a considerable
load on your computer. You probably use the
computer for applications other than audio,
but we recommend that you avoid running
them when using audio programs. This means
that if you are running other applications
(especially ones that are graphics-intensive
or that use Internet tools) at the same time as
an audio application, processing may not be
able to keep up the audio data.
Cubase LE 5 installation
See the included Cubase LE 5 Quick Start
Guide for details.
3 − Installation

TASCAM US-200 17
4 – US-200 control panel settings
Overview
The Control Panel lets you make various
settings for the US-200’s functionality.
On Windows, the US-200 Control Panel
shortcut can be found in the Windows Start
menu > Control Panel or the Start menu > All
Programs > TASCAM.
On Mac OS X, the US-200 Control Panel is
located in the Applications folder. Other
useful audio and MIDI settings for Mac OS X
can be found in Applications/Utilities/Audio
MIDI Setup.
The Control Panel is divided into the following
two sections.
Status section
This shows the current status of the driver
and the connected hardware.
You cannot edit the settings from this section.
Setting section
You can edit the various settings of the driver.
Control panel menus and
settings
Audio Performance
The US-200 driver temporarily stores input
and output audio sample in buffers. The size
of these buffers can be adjusted. A smaller
buffer size will reduce the delay when
monitoring the audio signal, but will require
your computer to perform the processing
faster. If the processing does not occur in
time (e.g., if other system operations are
occurring), you may hear clicks, pops, or
dropouts in the audio signal. A larger buffer
size provides more safety against such
problems caused by other system activities,
but will produce greater delay when
monitoring the audio signal. You should
select the buffer size that works best for your
system.
On the Windows version of the US-200
Control Panel, the Audio Performance setting
permits you to adjust the buffer size that
will be used by all audio applications. The
lowest latency setting is the minimum buffer
size, and the highest latency setting is the
maximum buffer size.
On Mac OS X, the buffer size is determined
by each audio application. Consequently,
there is no Audio Performance setting on
the Mac OS X version of the US-200 Control
Panel. Some applications select the buffer
size automatically while others permit the
user to select the buffer size. Please consult
your audio application’s documentation for
details.

18 TASCAM US-200
LINE OUTPUTS 1/2 and LINE
OUTPUTS 3/4
The computer can send 4 signal channels
by USB to this unit. Use this setting to select
which signals are output from the unit’s LINE
OUT 1/2 and LINE OUT 3/4 jacks. You can
select ch1+2 or ch3+4 for each output pair.
By using this setting, even with applications
that only output two channels, including
Windows Media Player and iTunes, you can
output the application sound from both the
LINE OUT 1/2 jacks and LINE OUT 3/4 jacks
of this unit.
4 – US-200 control panel settings

TASCAM US-200 19
Headphones Guitar Bass guitar Vocal mic
Drum machine
Computer
USB
CD recorder
Powered monitor speakers or
amplier and speakers
Example of using US-200 connections
5 – Connections

20 TASCAM US-200
USB connections
Use the included USB cable to connect the
US-200 to your computer as shown in the
illustration.
NOTE
Set the
•PHANTOM (+48V) switch to OFF
when connecting the USB cable to this
unit.
Some USB devices access the USB bus
•
frequently. To avoid dropouts and clicks in
the audio signal, we strongly recommend
that you do not connect any USB devices
other than keyboards and mice to the USB
bus used by this unit.
The USB indicator might stay lit even after
•
the connected computer is shut down.
This occurs with some computers that
continue to supply power over connected
USB cables even when they are shut
down.
Audio connections
Connect the output signal of your mic,
guitar, keyboard, or other audio device to the
US-200, where it will be converted into digital
audio and sent via USB to your computer.
Connect the output of the US-200 to your
speakers (via an amp) or headphones, so
you will be able to monitor the audio signals
coming into the US-200 or being produced
by your computer.
The balance between the input signal from
the mic and guitar and the output signal
from the computer should be adjusted by the
MON MIX knob.
Microphones
Connect microphones to the MIC/LINE/INST
IN 1 and MIC/LINE IN 2 XLR connectors on
the front panel. When using a condenser
microphone that requires phantom power,
set the PHANTOM (+48V) switch on the rear
panel to ON. When the PHANTOM (+48V)
switch is set to ON, the +48V indicator on the
front panel lights.
+48V (PHANTOM) indicator
CAUTION
Connecting a dynamic microphone with
•
an unbalanced connection to the unit
when the PHANTOM (+48V) switch is
ON could damage this unit and make it
unusable.
Do not connect or disconnect a mic with
•
an input when this switch is ON. Loud
noises might be produced and damage
could be caused to equipment.
Before changing the setting of the
•
PHANTOM (+48V) switch to ON or OFF,
turn the LEVEL knob to its minimum level.
Depending on the microphone connected,
a loud noise could occur, which might
damage equipment or harm hearing.
Set the
•PHANTOM (+48V) switch to OFF
before turning this unit’s power on or off
(connecting or disconnecting the USB
cable).
Do not use phantom power when line
•
level equipment is connected to an XLR
connector. It might damage equipment.
5 – Connections