Task Force Tips FlipTip Installation instructions

©Copyright Task Force Tips LLC 2012-2020 1 LIN-060 November 30, 2020 Rev02
TASK FORCE TIPS LLC
MADE IN USA · tft.com
3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 · 219-462-6161 · Fax [phone]
G-Force
INSTRUCTION FOR OPERATION AND MAINTENANCE
FlipTip™ NOZZLE
WARNING
Understand manual before use. Operation of this device without understanding the manual and
receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/serial-
number.
This equipment is intended for use by trained and qualified emergency services personnel for
firefighting. All personnel using this equipment shall have completed a course of education
approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize firefighters and maintenance personnel with the
operation, servicing, and safety procedures associated with this product. This manual should be
kept available to all operating and maintenance personnel.
FlipTip Only
No Shutoff
FlipTip
Valve Shutoff
FlipTip
Valve Shutoff w/Pistol Grip
G-Force FlipTip
Valve Shutoff w/Pistol Grip
G-Force FlipTip
Valve Shutoff

©Copyright Task Force Tips LLC 2012-2020 2 LIN-060 November 30, 2020 Rev02
TABLE OF CONTENTS
1.0 MEANING OF SAFETY SIGNAL WORDS
2.0 SAFETY
3.0 GENERAL INFORMATION
3.1 VARIOUS MODELS AND TERMS
3.2 SPECIFICATIONS
3.3 USE WITH SALT WATER
3.4 NOZZLE COUPLINGS
3.5 FLOW CHARACTERISTICS
4.0 FLIPTIP CONTROLS
4.1 REMOVABLE STREAM STRAIGHTENER
4.2 FLIPTIP LOCK
4.3 REAR SMOOTH BORE INSERTS
4.4 FRONT SMOOTH BORE NOZZLE
4.5 FRONT G-FORCE FOG NOZZLE
5.0 G-FORCE NOZZLE CONTROLS
5.1 PATTERN CONTROL
5.1.1 SHAPER TACTILE INDICATOR
5.1.2 FOG ANGLE ADJUSTMENT
5.2 FLUSH CONTROL
6.0 COLOR CODED HANDLE COVER AND PISTOL GRIPS
7.0 WARRANTY
8.0 MAINTENANCE
8.1 FIELD LUBRICATION
8.2 SERVICE TESTING
8.3 REPAIR
9.0 EXPLODED VIEWS AND PARTS LISTS
10.0 OPERATION AND INSPECTION CHECKLIST
LTT-108 Installation Instruction for
Pistol Grip Replacement Kit
©Copyright TaskForce Tips LLC 2011-2020 LIG-010 September 10, 2020 Rev07
MANUAL: Fixed, Selectable,
and Automatic Nozzles
North American Models
INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE
WARNING Understand manual before use. Operation of this device without understanding the manual and
receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/
serial-number
procedures associated with the G-Force nozzle.
This manual should be kept available to all operating and maintenance personnel.
3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax [phone]
G-Force
with Lever Handle
G-Force
Tip Only With Ball Valve
and Lever Handle
G-Force
with Lever Handle
and Pistol Grip
G-Force
with IMPULSE Trigger
Valve System
by:
®
LIG-010 Manual - G-Force Nozzle Series
DANGER
PERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response
equipment and services want responders to know and understand the
following:
1. Fire¿ghting and Emergency Response are inherently dangerous activities
requiring proper training in their hazards and the use of extreme caution
at all times.
2. It is your responsibility to read and understand any user’s instructions,
including purpose and limitations, provided with any piece of equipment
you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in
Fire¿ghting and /or Emergency Response and in the use, precautions, and
care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain
the personal skill level required to operate any equipment you may be
called upon to use.
5. It is your responsibility to know that your equipment is in operable
condition and has been maintained in accordance with the manufacturer’s
instructions.
6. Failure to follow these guidelines may result in death, burns or other
severe injury.
FEMSA
Fire and Emergency Manufacturers and Service Association
P.O. Box 147, Lynn¿eld, MA 01940 • www.FEMSA.org
SUPPORTING MATERIALS
The following documents contain supporting safety and operating
information pertaining to the equipment described in this manual.

©Copyright Task Force Tips LLC 2012-2020 3 LIN-060 November 30, 2020 Rev02
1.0 MEANING OF SAFETY SIGNAL WORDS
A safety related message is identified by a safety alert symbol and a signal word to indicate the level of risk involved with a particular
hazard. Per ANSI Z535.6, the definitions of the four signal words are as follows:
2.0 SAFETY
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor
or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
DANGER
An inadequate supply of pressure and/or flow will cause an ineffective stream and can result
in injury or death. Choose operating conditions to deliver adequate fire suppression. See flow
graphs.
WARNING
This equipment is intended for use by trained personnel for firefighting. Use of this equipment for
other purposes may involve hazards not addressed by this manual. Seek appropriate guidance and
training to reduce risk of injury.
WARNING
Equipment may be damaged if frozen while containing significant amounts of water. Such damage
may be difficult to detect visually. Subsequent pressurization can lead to injury or death. Any time
the equipment is subject to possible damage due to freezing, it must be tested and approved for
use by qualified personnel before being considered safe for use.
WARNING
Failure to restrain nozzle reaction can cause firefighter injury from loss of footing and/or stream
protection. Opening and closing other nozzles, hose line kinks, changes in pump settings, nozzle
pattern, or flushing will cause changes in nozzle reaction. Nozzle operator must always be prepared
in the event of these changes.
WARNING
If nozzle gets out of control while flowing, violent whipping motion will occur. Serious injury or
death could result. Retreat from the nozzle immediately. Do not attempt to regain control of nozzle
while flowing.
WARNING
Application of water or foam solutions on energized electrical equipment could cause
electrocution. Serious injury or death could result. Assume circuits are energized until confirmed to
be de-energized. Do not apply water or foam to energized electrical equipment.
WARNING
The stream exiting a nozzle is powerful and capable of causing injury and property damage. Make
sure the nozzle is securely attached and pointing in a safe direction before water is turned on. Do
not direct water stream to cause injury or damage to persons or property.
NOTICE
To prevent mechanical damage, do not drop or throw equipment.

©Copyright Task Force Tips LLC 2012-2020 4 LIN-060 November 30, 2020 Rev02
3.0 GENERAL INFORMATION
The Task Force Tips FlipTip nozzles are designed to provide excellent performance under most fire fighting conditions. Their rugged
construction is compatible with the use of fresh water as well as fire fighting foam solutions.
3.1 VARIOUS MODELS AND TERMS
The TFT FlipTip nozzle is available in several configurations. The FlipTip nozzle is available with or without a pistol grip. Various models
are shown below.
Figure 3.1
3.2 SPECIFICATIONS
3.3 USE WITH SALT WATER
Use with salt water is permissible provided the equipment is thoroughly cleaned with fresh water after each use. The service life of the
equipment may be shortened due to the effects of corrosion, and is not covered under warranty.
3.4 NOZZLE COUPLINGS
NH (National Hose Threads) threads are standard on all nozzles. Other threads such as NPSH (National Pipe Straight Hose) may be
specified at time of order.
Maximum operating pressure (with valve shut off)* 300 psi 20 bar
Operating temperature range of fluid 33 to 120° F 1 to 50° C
Storage temperature range -40 to 150° F -40 to 65° C
Materials used Aluminum 6000 series hard anodized MIL8625 class 3 type 2,
stainless steel 300 series, nylon 6-6, nitrile rubber
*Consult factory for higher pressure applications
CAUTION Mismatched or damaged waterway connections may cause equipment to leak or uncouple under
pressure. Failure could result in injury. Equipment must be mated to matched connections.
CAUTION Dissimilar metals coupled together can cause galvanic corrosion that can result in the inability to
uncouple the connection, or complete loss of engagement over time. Failure could cause injury. Per
NFPA 1962, if dissimilar metals are left coupled together, an anti-corrosive lubricant should be
applied to the connection and the coupling should be disconnected and inspected at least
quarterly.
FlipTip Only
No Shutoff
Ball Valve with Smoothbore Rear
and Smoothbore Front
Ball Valve With Smoothbore Rear
and G-Force Fog Nozzle Front
Locking Ring
Coupling
Pistol Grip
G-Force Fog Nozzle
See LIG-010 for
more information
OFFON
Flow Control
Removeable
Stream Straightener*
Available Rear Smoothbores:
7/8”, 15/16”, 1”, 1-1/8”, 1-1/4“, or 1-3/8”
(22mm, 24mm, 25mm, 29mm, 32mm, or 35mm)
Available Front Smoothbores:
1/2", 5/8", 7/8", 15/16", 1", 1-1/8", or 1-3/16"
(13mm, 16mm, 22mm, 24mm, 25mm, 29mm, or 35mm)
Serial Number
(on top of valve just ahead of coupling)
Serial Number
(on top of valve just ahead of coupling)
* Standard for 1.5" connections. A special coupling (P205) is needed
to work for 2.5" connections. Contact TFT for details.

©Copyright Task Force Tips LLC 2012-2020 5 LIN-060 November 30, 2020 Rev02
3.5 FLOW CHARACTERISTICS
The FlipTip nozzle has fixed orifice sizes. Relationship of flow and nozzle pressure at each orifice size is shown below. If the nozzle is
connected behind a different nozzle, use the flow charts for the outlet nozzle.
Figure 3.0
Flows at specific pressures for each orifice size are as follows:
1/2” TIP 5/8” TIP 7/8” TIP
PRESSURE FLOW REACTION PRESSURE FLOW REACTION PRESSURE FLOW REACTION
PSI GPM LBS PSI GPM LBS PSI GPM LBS
40 47 16 40 73 25 40 144 48
50 53 20 50 82 31 50 161 60
60 58 24 60 90 37 60 176 72
70 62 27 70 97 43 70 190 84
80 66 31 80 104 49 80 203 86
15/16” TIP 1” TIP 1-1/8” TIP
PRESSURE FLOW REACTION PRESSURE FLOW REACTION PRESSURE FLOW REACTION
PSI GPM LBS PSI GPM LBS PSI GPM LBS
40 165 55 40 188 63 40 238 79
50 185 69 50 210 79 50 266 99
60 202 83 60 230 90 60 291 119
70 218 97 70 249 110 70 315 139
80 234 110 80 266 126 80 366 159
1-1/4” TIP 1-3/8” TIP
PRESSURE FLOW REACTION PRESSURE FLOW REACTION
PSI GPM LBS PSI GPM LBS
40 294 98 40 355 119
50 328 123 50 397 148
60 360 147 60 435 178
70 388 172 70 470 208
80 415 196 80 502 237
1/2"
5/8"
7/8"
15/16"
1"
1 1/8"
1 1/4"
1 3/8"
0
1
2
3
4
5
6
7
0
10
20
30
40
50
60
70
80
90
100
0 100 200 300 400 500 600
PRESSURE (BAR)
PRESSURE (PSI)
FLOW (GPM)
0 500 1000 1500 2000
FLOW (LPM)

©Copyright Task Force Tips LLC 2012-2020 6 LIN-060 November 30, 2020 Rev02
4.0 FlipTip CONTROLS
4.1 REMOVABLE STREAM STRAIGHTENER
Stream quality is generally improved with use of an integral stream straightener at the FlipTip inlet. The FlipTip may be used without the
straightener if so desired.
The removable stream straightener is a standard option for 1.5” connections.
TFT's 2.5” connections utilize an optimized waterway in place of the stream straightener. If so desired, the straightener can still be used
with a special 2.5” coupling (P205). Contact TFT for details.
Figure 4.1
4.2 FlipTip LOCK
The front nozzle is locked in both the up and down positions. To change positions, follow the steps below.
Figure 4.2
NOTICE
The FlipTip pivoting joint is not sealed between the fully up and fully down positions. Shut off water
flow before changing the front nozzle position to avoid spraying in unintended directions.
NOTICE
When the front nozzle is in the down position, the sealing surfaces are exposed. Avoid actions
which can damage the sealing surfaces to prevent possible leakage and repairs.
Stream Straightener
FlipTip with smooth bore front
flipped down
To remove the straightener, flip
the smooth bore front down,
open valve fully, insert a wooden
dowel or similar tool to push
the straightener out the rear of
the coupling.
Unlock
Flip Down
1
2
Unlock Flip Up
1
2

©Copyright Task Force Tips LLC 2012-2020 7 LIN-060 November 30, 2020 Rev02
4.3 REAR SMOOTH BORE INSERTS
The rear smooth bore inserts may be removed by removing the retaining ring and pulling the insert out the front of the nozzle.
Figure 4.3
4.4 FRONT SMOOTH BORE NOZZLE
Figure 4.4
4.5 FRONT G-FORCE FOG NOZZLE
The Flip Tip with G-Force fog nozzle allows selection between a smooth bore and a fog nozzle. The G-For ce for nozzle is available in fixed opening, selectable, or automatic versions. See the G-Force owners manual LIG-010 for details.
Figure 4.5
CAUTION The lock for the front nozzle is not intended to withstand nozzle reaction force. To reduce the risk of
injury from unintended unlocking due to nozzle reaction, do not use the front nozzle in the down
position as a handle to restrain nozzle reaction.
1-3/8” diameter* if no insert is installed
Smooth bore insert
O-Ring
Retaining ring
(use a pick or similar
tool to remove)
Insert removes in this direction
*1-1/4” models have a diameter of 1-1/4”
and do not accept a rear insert.
Male Hose Thread for attaching a hose
or other nozzle of the proper thread
Smooth bore nozzle
G-Force Fog Nozzle
Rear
Smooth bore insert

©Copyright Task Force Tips LLC 2012-2020 8 LIN-060 November 30, 2020 Rev02
5.0 G-FORCE NOZZLE CONTROLS
5.1 PATTERN CONTROL
TFT nozzles have full pattern control from straight stream to wide fog. Turning the stream shaper clockwise (as seen from the operating
position behind the nozzle) moves the shaper to the straight stream position. Turning the shaper counterclockwise will result in an
increasingly wider pattern.
Since the stream trim point varies with flow, the stream should be “trimmed” after changing the flow to obtain the straightest and farthest
reaching stream. To properly trim the stream, first open the pattern to narrow fog. Then close the stream to parallel to give maximum
reach. Turning the shaper further forward will cause stream crossover and reduce the effective reach of the nozzle.
5.1.1 SHAPER TACTILE INDICATOR
The G-Force has a tactile indicator on the stream shaper. The tactile
indicator allows the stream shaper position (and fog angle) to be determined
by feel rather than by sight. The fog angle can be adjusted so that the
desired fog angle is achieved when the tactile indicator is on top of the
nozzle. The G-Force has an optional detent to aid in returning to a known
fog angle.
5.1.2 FOG ANGLE ADJUSTMENT
Typically, the G-Force is factory set with the tactile indicator in the top
position for straight stream. The fog angle can be adjusted while
keeping the tactile indicator on top by following the steps in (see Figure
5.2.3). If the fog angle is changed/adjusted, a new shaper label is
needed.
5.2 FLUSH CONTROL
Small debris passes through the debris screen (if so equipped) and
may get caught inside the nozzle. This trapped material will cause poor
stream quality, shortened reach, and reduced flow. To remove small debris, the nozzle may be flushed as follows:
• While still flowing water, rotate the shaper counterclockwise (as viewed from behind the nozzle) to the flush position. This will
open the nozzle allowing debris to pass through. Increased resistance will be felt on the SHAPER as the nozzle goes into flush.
• During flush the nozzle reaction will decrease as the pattern becomes wider and the pressure drops. The nozzle operator must
be prepared for an increase of nozzle reaction when returning the nozzle from the flush position to retain control of the nozzle.
• Rotate the shaper out of flush to continue normal operations.
WARNING
The nozzle reaction is greatest when the shaper is in the straight stream position. Sudden changes
in pattern can cause changes in reaction, leading to loss of footing or an out of control nozzle. The
nozzle operator must be prepared for a change in reaction as the pattern is changed.
CAUTION Dents or nicks in the nozzle tip can seriously affect the stream reach or pattern, which may increase
the risk of injury due to exposure. Care must be taken to avoid dents or nicks in the nozzle tip.
NOTICE
Turning the shaper further forward will cause stream crossover and reduce the reach of the nozzle.
NOTICE
The fog angle will change as flow and pressure change (becoming wider with increased flow).
WARNING
Large amounts or pieces of debris may be unflushable and can reduce the flow of the nozzle
resulting in an ineffective flow. In the event of a blockage, it may be necessary to retreat to a safe
area, uncouple the nozzle and remove debris.
TACTILE INDICATOR
(MOVES WITH BUMPER)
Figure 5.1.1
1) Remove or cut the shaper label.
2) Loosen the clamp ring
with a pin spanner.
3) While keeping the tactile indicator
or lock out lever on top,
rotate the shaper guide
to obtain the desired fog angle.
4) Tighten the clamp ring
with a pin spanner.
5) Apply a new shaper label.
Figure 5.1.2

©Copyright Task Force Tips LLC 2012-2020 9 LIN-060 November 30, 2020 Rev02
6.0 COLOR CODED HANDLE COVER AND PISTOL GRIPS
Nozzles with lever type valve handles are supplied with black valve handle covers and pistol grips. The handle covers and pistol grips
are available from TFT in various colors for those departments wishing to color code the nozzle to the discharge controls. A colored
handle cover set will be sent upon receipt of the warranty card by TFT.
Handle covers are replaceable by removing the four screws that hold the handle covers in place. Use a 3/32” hex key when replacing
screws. Pistol grip is replaceable by following TFT instruction sheet LTT-108.
For standardization NFPA 1901 recommends the following color code scheme:
Preconnect #1 or Jump Line Orange Other Colors Available:
Preconnect #2 Red - Gray
Preconnect #3 Yellow - Pink
Preconnect #4 White - Purple
Preconnect #5 Blue - Tan
Preconnect #6 Black
Preconnect #7 Green
Foam Lines Red w/ White Border (Red/White)

©Copyright Task Force Tips LLC 2012-2020 10 LIN-060 November 30, 2020 Rev02
7.0 WARRANTY
Task Force Tips LLC, 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA (“TFT”) warrants to the original purchaser of its
products (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from defects in material and
workmanship during the five (5) year period from the date of purchase. TFT’s obligation under this warranty is specifically limited to
replacing or repairing the equipment (or its parts) which are shown by TFT’s examination to be in a defective condition attributable to
TFT. To qualify for this limited warranty, the claimant must return the equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana
46383-9327 USA, within a reasonable time after discovery of the defect. TFT will examine the equipment. If TFT determines that there is
a defect attributable to it, TFT will correct the problem within a reasonable time. If the equipment is covered by this limited warranty, TFT
will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is an
intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any consequential or incidental damages
for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT.
It is agreed and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE.
THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

©Copyright Task Force Tips LLC 2012-2020 11 LIN-060 November 30, 2020 Rev02
8.0 MAINTENANCE
TFT products are designed and manufactured to be damage resistant and require minimal maintenance. However, as the primary
firefighting tool upon which your life depends, it should be treated accordingly. To help prevent mechanical damage, do not drop or throw
equipment.
8.1 FIELD LUBRICATION
All Task Force Tips nozzles are factory lubricated with high quality silicone grease. This lubricant has excellent wash out resistance,
providing long term performance in firefighting nozzles. If your agency has unusually hard or sandy water, the moving parts of the nozzle
may be affected. Foam agents and water additives contain soaps and chemicals that may break down the factory lubrication.
The moving parts of the nozzle should be checked on a regular basis for smooth and free operation, and for signs of damage. IF THE
NOZZLE IS OPERATING CORRECTLY, THEN NO ADDITIONAL LUBRICANT IS NEEDED. Any nozzle that is not operating correctly
should be immediately removed from service. The nozzle can be returned to the factory at any time for a complete checkup and re-
lubrication with silicone grease.
The field use of Break Free CLP (spray or liquid) lubricant will help to temporarily restore the smooth and free operation of the nozzle.
These lubricants do not have the washout resistance and long-term performance of the silicone grease. Once Break Free CLP is
applied, re-application will be needed on a regular basis until the nozzle can be returned to the factory for a complete checkup and re-
lubrication with silicone grease.
8.2 SERVICE TESTING
In accordance with NFPA 1962, equipment must be tested a minimum of annually. Units failing any part of this test must be removed
from service, repaired and retested upon completion of the repair.
8.3 REPAIR
Factory service is available with repair time seldom exceeding one day in our facility. Factory serviced equipment is repaired by
experienced technicians, wet tested to original specifications, and promptly returned. Any returns should include a note as to the nature
of the problem and whom to reach in case of questions.
Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no liability for
damage to equipment or injury to personnel that is a result of user service. Contact the factory or visit the web site at tft.com for parts
lists, exploded views, test procedures and troubleshooting guides.
Performance tests shall be conducted on the equipment after a repair, or anytime a problem is reported to verify operation in accordance
with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the equipment. Any
equipment which fails the related test criteria should be removed from service immediately. Troubleshooting guides are available with
each test procedure or equipment can be returned to the factory for service and testing.
9.0 EXPLODED VIEWS AND PARTS LISTS
Exploded views and parts lists are available at tft.com/serial-number.
CAUTION Aerosol lubricants contain solvents that can swell O-Rings if applied in excess. The swelling can
inhibit smooth operation of the moving parts. When used in moderation, as directed, the solvents
quickly evaporate without adversely swelling the O-Rings.
CAUTION Any alterations to the product or its markings could diminish safety and constitutes a misuse of
this product.
NOTICE
All replacement parts must be obtained from the manufacturer to assure proper operation of the
device.

©Copyright Task Force Tips LLC 2012-2020 12 LIN-060 November 30, 2020 Rev02
TASK FORCE TIPS LLC
MADE IN USA · tft.com
3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 · 219-462-6161 · Fax [phone]
10.0 OPERATION AND INSPECTION CHECKLIST
BEFORE EACH USE, the nozzle must be inspected to this checklist:
1. There is no obvious damage such as missing, broken or loose parts, damaged labels etc.
2. Waterway is clear of obstructions
3. Coupling is tight and leak free
4. Valve operates freely through full range and regulates flow
5. “OFF” position shuts off fully and flow is stopped
6. Nozzle flow is adequate as indicated by pump pressure and nozzle reaction
7. Shaper turns freely and adjusts pattern through full range
8. Nozzle smoothly moves into full flush and out of flush with normal flow and pressure restored
9. Shaper detent (if so equipped) operates smoothly and positively.
BEFORE BEING PLACED BACK IN SERVICE, nozzles must be inspected to this checklist:
1. All controls and adjustments are operational
2. Shut off valve (if so equipped) closes off the flow completely
3. There are no broken or missing parts
4. There is no damage to the nozzle that could impair safe operation (e.g. dents, cracks, corrosion or other defects)
5. The thread gasket is in good condition
6. The waterway is clear of obstructions
7. Nozzle is clean and markings are legible
8. Coupling is retightened properly
9. Shaper is set to desired pattern
10. Shutoff handle is stored in the OFF position
NFPA 1962: Standard for the care, use, inspection, service testing, and replacement of fire hose, couplings, nozzles and fire hose appliances. Quincy, MA: National Fire
Protection Agency
WARNING
Equipment failing any part of the checklist is unsafe for use and must have the problem corrected
before use or being placed back into service. Operating equipment that has failed the checklist is a
misuse of this equipment.