Task Force Tips Max Flip Tip2 User manual

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
MANUAL: 2 1/2” FLIP TIP2TM NOZZLE
PATENTS PENDING
INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE
WARNING Understand manual before use. Operation of this device without understanding the manual and
receiving proper training is a misuse of this equipment. Obtain safety information at www.tft.
com/serial-number
NOTICE This instruction manual is intended to familiarize fi refi ghters and maintenance personnel with
the operation, servicing and safety procedures associated with the Flip Tip2 fi re fi ghting nozzles.
This manual should be kept available to all operating and maintenance personnel.
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219- 462-6161 • Fax [phone]
DANGER
PERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response
equipment and services want responders to know and understand the
following:
1. Firefi ghting and Emergency Response are inherently dangerous activities
requiring proper training in their hazards and the use of extreme caution
at all times.
2. It is your responsibility to read and understand any user’s instructions,
including purpose and limitations, provided with any piece of equipment
you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in
Firefi ghting and /or Emergency Response and in the use, precautions, and
care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain
the personal skill level required to operate any equipment you may be
called upon to use.
5. It is your responsibility to know that your equipment is in operable
condition and has been maintained in accordance with the manufacturer’s
instructions.
6. Failure to follow these guidelines may result in death, burns or other
severe injury.
FEMSA
Fire and Emergency Manufacturers and Service Association
P.O. Box 147, Lynnfi eld, MA 01940 • www.FEMSA.org
Max Series 2.5" Flip Tip2
No Shutoff
2.5" Flip Tip2 Tip Only
No Shutoff

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
2
TABLE OF CONTENTS
1.0 MEANING OF SAFETY SIGNAL WORDS
2.0 GENERAL INFORMATION
2.1 VARIOUS MODELS AND TERMS
2.2 NOZZLE COUPLINGS
2.3 FLIP TIP2 LOCK
2.4 REAR SMOOTHBORE INSERTS
2.5 FRONT SMOOTHBORE NOZZLE
2.6 FRONT MAX SERIES COMBINATION NOZZLE
2.7 MECHANICAL SPECIFICATIONS
3.0 FLOW CHARACTERISTICS and CHARTS
4.0 FIRE GROUND USE OF FLIP TIP2 NOZZLES
4.1 USE WITH SALT WATER
5.0 FIELD INSPECTION
6.0 INSPECTION CHECKLIST
7.0 ANSWERS TO YOUR QUESTIONS
8.0 EXPLODED VIEW AND PARTS LIST
9.0 WARRANTY

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
3
1.0 MEANING OF SAFETY SIGNAL WORDS
A safety related message is identifi ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular
hazard. Per ANSI standard Z535.6-2011, the defi nitions of the four signal words are as follows:
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor
or moderate injury.
NOTICE NOTICE is used to address practices not related to physical injury.
2.0 GENERAL INFORMATION
The Task Force Tips Flip Tip2 nozzles are designed to provide excellent performance under most fi re fi ghting conditions. Their
rugged construction is compatible with the use of fresh water as well as fi re fi ghting foam solutions. Other important operating
features include:
• Changeable smooth bore tips
• TFT’s fi ve-year warranty and unsurpassed customer service
WARNING This equipment is intended for use by trained personnel for fi refi ghting. Their use for other
purposes may involve hazards not addressed by this manual. Seek appropriate guidance and
training to reduce risk of injury.
WARNING Water is a conductor of electricity. Application of water solutions on high voltage equipment can
cause injury or death by electrocution. The amount of current that may be carried back to the
nozzle will depend on the following factors: Voltage of the line or equipment; Distance from
the nozzle to the line or equipment; Size of the stream; Weather the stream is solid or broken;
Purity of the water.1
WARNING Water discharged at high velocity can cause injury or death from impact, ingestion, or loss of
footing. Make sure the nozzle is pointing in a safe direction before discharging water. Use care
in directing the stream.
WARNING Failure to restrain nozzle reaction can cause fi refi ghter injury from loss of footing and/or stream
protection. Expect reaction variations from: opening or closing other nozzles, hose line kinks,
changes in pump settings, spray pattern change, or fl ushing. Nozzle control valves must be
opened and closed slowly to eliminate unnecessary strain on the hose and couplings and
reduce pressure surges.
WARNING Do not attempt to regain control of nozzle/monitor while fl owing water. Injury from whipping can
occur. If nozzle/monitor gets out of control or away from operator, retreat immediately. Shutoff
water at the source.
WARNING Use of compressed air foam (CAF) with portable nozzles can cause sudden surges in nozzle
reaction force resulting in injury or death from loss of footing, hose whipping, or an out of
control portable monitor. Be prepared for sudden changes in nozzle reaction caused by: Slug
loading (Loss of foam concentrate sends slugs of air and water into the nozzle) Sudden release
of built-up pressure in the hose when opening a nozzle
[Footnote 1: The Fire Fighter and Electrical Equipment, The University of Michigan Extension Service, Fourth Printing 1983, Page 47.]

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
4
2.2 NOZZLE COUPLINGS
NH (National Hose Threads per NFPA #1963) threads are standard on all FlipTip2 nozzles. Other threads such as NPSH (National
Pipe Straight Hose threads per ANSI/ASME #B1.20.7) can be specifi ed at time of order.
CAUTION Nozzle must be properly connected. Mismatched or damaged threads may cause nozzle to leak
or uncouple under pressure and could cause injury.
CAUTION Dissimilar metals coupled together can cause galvanic corrosion that can result in the inability
to unscrew the threads or complete loss of thread engagement over time. Per NFPA 1962
(2008 edition), if dissimilar metals are left coupled together an anti-corrosive lubricant should
be applied to the threads. Also, the coupling should be disconnected and inspected at least
quarterly.
2.1 VARIOUS MODELS AND TERMS
The TFT Flip Tip2 nozzle is available in several diff erent confi gurations. Figure 2.1 shows the common models.
2.5" Flip Tip2 With Max Series
No Shutoff w/Combination Nozzle Front
Max Series Combination Nozzle
See LIM-025 For
More Information
Available Rear Smooth Bores:
1 1/4", 1 3/8", 1 1/2"
1 3/4" & 2”
Locking Ring
2.5" Flip Tip2 Tip Only
No Shutoff
Locking Ring Available Front Smooth Bores:
1.0", 1 1/4", 1 3/8" & 1 1/2"
Serial Number
Figure 2.1 Common Models and Terms

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
5
2.3 FLIP TIP2 LOCK
The front nozzle is locked in both positions. To change positions follow the steps in fi gure 2.3.
1Unlock
2Flip Up
1Unlock
2Flip Down
Figure 2.3 Using the Flip Tip2 Lock
CAUTION Do not pivot the Flip Tip between positions while fl owing water. High velocity water can be
discharged in harmful directions. Always turn off water before changing positions.
NOTICE When the front nozzle is in the down position the sealing surfaces are exposed. Avoid actions
which can damage the sealing surface to prevent possible leakage and repairs.
2.4 REAR SMOOTH BORE INSERTS
The rear smooth bore inserts may be removed by removing the retaining ring and pulling the insert out the front of the nozzle.
2.0" diameter if no insert is installed
Smooth Bore Insert
1.0", 1 1/4", 1 3/8" or 1 1/2"
O-Ring
Retaining Ring
(use a pick or similar
tool to remove)
Insert removes in this directi
on
Figure 2.4 Rear Smooth Bore Inserts
2.5 FRONT SMOOTH BORE NOZZLE
Male Hose Thread for attaching a hose
or other nozzle of proper thread
Smooth Bore Nozzle
Figure 2.5 Front Smooth Bore Nozzles

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
6
2.6 FRONT MAX SERIES COMBINATION NOZZLE
The Flip Tip2 with Max Series combination nozzle allows selection between a smooth bore and a fog nozzle. See the Max-Force
owners manual LIM-025 for details.
Max Series
Combination
Nozzle
Rear
Smooth Bore
Insert
Figure 2.6 Front Max Series Combination Nozzle
CAUTION The lock for the front nozzle is not designed to withstand the full force of the nozzle reaction.
Injury from inadvertent unlocking may result. Do not use the front nozzle in the down position
as a handle to restrain the nozzle reaction.
2.7 MECHANICAL SPECIFICATIONS
Maximum nozzle inlet pressure with valve shutoff * 300 psi 20 bar
Operating temperature range of fl uid 33 to 120º F 1 to 50º C
Storage temperature range -40 to 150º F -40 to 65º C
Materials used Aluminum 6000 series hard anodized MIL8625 class 3 type 2,
stainless steel 300 series, nylon 6-6, nitrile rubber
*Consult Factory for higher pressure applications

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
7
3.0 FLOW CHARACTERISTICS AND CHARTS
The Flip Tip2 nozzle has fi xed orifi ce sizes. Relationship of fl ow and nozzle pressure at each orifi ce size is shown below. If the Flip
Tip2 is connected behind a diff erent nozzle, use the fl ow charts for the outlet nozzle.
0 500 1000 1500 2000 2500
0
1
2
3
4
5
6
7
8
0
10
20
30
40
50
60
70
80
90
100
110
120
0 100 200 300 400 500 600 700
FLOW (LPM)
PRESSURE (BAR)
PRESSURE (PSI)
FLOW (GPM)
1 3/4"
1 3/8"1 1/4"
1.0"
2.0"
1 1/2"
Figure 3.0 Flip Tip Flow Chart
Flows at specifi c pressures for each orifi ce size are as follows:
1.0” TIP
PRESSURE FLOW REACTION
PSI GPM LBS
40 190 60
50 210 80
60 230 90
70 250 110
80 270 130
90 280 140
100 300 160
1 1/4” TIP
PRESSURE FLOW REACTION
PSI GPM LBS
40 290 100
50 330 120
60 360 150
70 390 170
80 420 200
90 440 220
100 460 240
1 3/8” TIP
PRESSURE FLOW REACTION
PSI GPM LBS
40 360 120
50 400 150
60 440 180
70 470 210
80 500 240
90 530 270
100 560 300
1 1/2” TIP
PRESSURE FLOW REACTION
PSI GPM LBS
40 420 140
50 470 180
60 520 210
70 560 250
80 600 280
90 630 320
100 670 350
1 3/4” TIP
PRESSURE FLOW REACTION
PSI GPM LBS
40 580 190
50 640 240
60 700 290
70 760 340
80 810 380
90 860 430
100 910 480
2.0” TIP
PRESSURE FLOW REACTION
PSI GPM LBS
40 750 250
50 840 310
60 920 380
70 990 440
80 1060 500
90 1130 570
100 1190 630
DANGER An inadequate supply of nozzle pressure and/or fl ow will cause an ineff ective stream and can
result in injury, death or loss of property. See fl ow charts in Section 3.0 or call 800-348-2686 for
assistance.

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
8
The rear nozzle restricts fl ow somewhat to the Max-Series front nozzle. The smaller the rear nozzle the greater the eff ect. Figures
3.1, 3.2, and 3.3 show the range from no rear insert to a 1 3/8 inch rear smooth bore. 1 3/8 inch is the smallest size available for use
with a Max-Series front end.
2 1/2" FLIP TIP2 100 PSI MAXFORCE AND MAXMATIC FRONT END
0 400 800 1200 1600 2000
0
1
2
3
4
5
6
7
8
9
10
11
0
20
40
60
80
100
120
140
160
0 100 200 300 400 500 600
FLOW (LPM)
PRESSURE (BAR)
PRESSURE (PSI)
FLOW (GPM)
100 PSI, NO REAR INSERT
100 PSI, 1 3/8" REAR INSERT
OPERATING ENVELOPE
PER NFPA 1964
LOW PRESSURE MODE,
1 3/8" REAR INSERT
LOW PRESSURE MODE,
NO REAR INSERT
Figure 3.1
0 400 800 1200 1600 2000
0
1
2
3
4
5
6
7
8
9
10
11
0
20
40
60
80
100
120
140
160
0 100 200 300 400 500 600
FLOW (LPM)
PRESSURE (BAR)
PRESSURE(PSI)
FLOW(GPM)
2 1/2" FLIP TIP2 80 PSI MAXMATIC
OPERATING ENVELOPE
PER NFPA 1964
80 PSI MAXMATIC
1 3/8" REAR INSERT
80 PSI MAXMATIC
NO REAR INSERT
Figure 3.2

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
9
0 400 800 1200 1600 2000
0
1
2
3
4
5
6
7
8
9
10
11
0
20
40
60
80
100
120
140
160
0 100 200 300 400 500 600
FLOW (LPM)
PRESSURE (BAR)
PRESSURE(PSI)
FLOW(GPM)
2 1/2" FLIP TIP2 500 GPM MAXFLOW
500 GPM MAXFLOW
NO REAR INSERT
500 GPM MAXFLOW
1 3/8" REAR INSERT
Figure 3.3
4.0 FIREGROUND USE OF FLIP TIP2 NOZZLES
IT IS THE RESPONSIBILITY OF THE INDIVIDUAL FIRE DEPARTMENT OR AGENCY TO DETERMINE PHYSICAL CAPABILITIES
AND SUITABILITY FOR AN INDIVIDUAL’S USE OF THIS EQUIPMENT.
Many factors contribute to the extinguishment of a fi re. Among the most
important is delivering water at a fl ow rate suffi cient to absorb heat faster
than it is being generated. The fl ow rate depends largely on the pump
discharge pressure and hose friction loss. The pump discharge pressure
can be calculated using a hydraulic equation such as:
PDP = NP + FL + DL + EL
PDP = Pump discharge pressure in PSI
NP = Nozzle pressure in PSI
FL = Hose friction loss in PSI
DL = Device loss in PSI
EL = Elevation loss in PSI
For additional information on calculating specifi c hose layouts, consult an appropriate fi re service training manual such at IFSTA, A
Guide to Automatic Nozzles, or call TFT’s “Hydraulics Hotline” at 800-348-2686.
CAUTION The nozzle may be damaged if frozen while containing signifi cant amounts of water. Such damage
may be diffi cult to detect visually and can lead to possible injury or death. Any time the nozzle is
subject to possible damage due to freezing, it must be tested by qualifi ed personnel before being
considered safe for use.
4.1 USE WITH SALT WATER
NOTICE Use with salt water is permissible provided the nozzle is thoroughly cleaned with fresh water after
each use. The service life of the nozzle may be shortened due to the eff ects of corrosion and is
not covered under warranty.

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
10
5.0 FIELD INSPECTION
TFT’S Flip Tip2 is designed and manufactured to be damage resistant and require minimal maintenance. However, as the primary
fi re fi ghting tool upon which your life depends, it should be treated accordingly.
WARNING Nozzle must be inspected for proper operation and function according to the inspection
checklist in Section 6.0 before each use. Any nozzle that fails inspection is dangerous to use
and must be repaired before using.
Performance tests shall be conducted on the Flip Tip2 nozzle after a repair, or anytime a problem is reported to verify operation in
accordance with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the
nozzle. Any equipment which fails the related test criteria should be removed from service immediately.
Factory service is available with repair time seldom exceeding one day in our facility. Factory serviced nozzles are repaired by
experienced technicians to original specifi cations, fully tested and promptly returned. Any returns should include a note as to the
nature of the problem, who to reach in case of questions and if a repair estimate is required.
Repair parts are available for those wishing to perform their own repairs. Task Force Tips assumes no liability for damage to
equipment or injury to personnel that is a result of user service.
CAUTION Any alteration to the nozzle and its markings could diminish safety and constitutes a misuse
of this product.
All Task Force Tips nozzles are factory lubricated with high quality silicone grease. This lubricant has excellent washout resistance
and long term performance. If your department has unusually hard or sandy water, the moving parts may be aff ected. Foam agents
and water additives contain soaps and chemicals that may break down the factory lubrication.
The moving parts of the nozzle should be checked on a regular basis for smooth and free operation, and signs of damage. IF THE
NOZZLE IS OPERATING CORRECTLY, THEN NO ADDITIONAL LUBRICATION IS NEEDED. Any nozzle that is not operating
correctly should be immediately removed from service and the problem corrected.
6.0 INSPECTION CHECKLIST
Nozzle must be inspected for proper operation and function according to the checklist before each use. Check that:
1) There is no obvious damage such as missing parts, broken or loose parts, damaged labels, etc.
2) Coupling is tight and leak free
5) Nozzle fl ow is adequate as indicated by the pump pressure and nozzle reaction.
6) Front end is tight and leak free
7) Locking ring operates smoothly.
WARNING Any Flip Tip2 nozzle failing any part of the inspection checklist is unsafe and must have the
problem corrected before use. Operating a nozzle that fails any of the above inspections is a
misuse of this equipment.
7.0 ANSWERS TO YOUR QUESTIONS
We appreciate the opportunity of serving you and making your job easier. If you have any problems or questions, our toll-free
“Hydraulics Hotline”, 800-348-2686 or 1-219-462-6161 is normally available to you 24 hours a day, 7 days a week.

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
11
8.0 EXPLODED VIEW AND PARTS LIST
24
20
21
22
23
16
15
14
22
23
20
21
19
18
1
17
14 16
15
13
12
11
10
9
8
7
56
3
24
1
MAX-SERIES FRONT END
SEE LIM-025
FOR MAX-SERIES
PARTS LIST & EXPLODED VIEW
25
ITEM DESCRIPTION QTY PART #
1 GASKET - 2.5" 2 V3190
2 1/4-28 X 1/2 SOCKET SETSCREW 1 VT25-28SS500
3 3/16" SS BALL 48 V2120
4 COUPLING 1.5" ROCKERLUG 1 M307*
5 NAME LABEL 1 FF202L
6 BASE 1 FF202
7 TRUNNION 2 FF110
8
1 1/4" SMOOTH BORE INSERT
1
FF211
1 3/8" SMOOTH BORE INSERT FF212
1 1/2" SMOOTH BORE INSERT FF213
1 3/4" SMOOTH BORE INSERT FF214
9 O-RING-133 1 VO-133
10 SMALLEY RING 1 V4292
11 SEAT 1 FF240
12 O-RING-METRIC 2 VO-3.5X55
13 LOCK 1 FF220
ITEM DESCRIPTION QTY PART #
14 DRAG NUBS 2 B650
15 YOKE 2.5" 1FF250*
YOKE, MAX SERIES FF260
16 SLIDE SPRING 2 XG141
17 LOCK RING 1 FF225
18
1.0" SMOOTH BORE
1
FF251
1 1/4" SMOOTH BORE FF252
1 3/8" SMOOTH BORE FF253
1 1/2" SMOOTH BORE FF254
19 COUPLING 2.5" 1 FF245*
20 NYLON BUSHING 2 AY307
21 CAM SCREW 2 FF126
22 1/8"ACETALBALL 2 VB125AC
23 10-32 X 1/4 SOCKET SETSCREW 2 VT10-32SS250
24 O-RING-147 1 VO-147
25 MAX BARREL 1 FF261
* - CONSULT FACTORYFOR SPECIALTHREADS

©Copyright Task Force Tips, Inc. 2014 LIN-065 February 11, 2014 Rev00
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219- 462-6161 • Fax [phone]
9.0 WARRANTY
Task Force Tips, Inc., 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA (“TFT”) warrants to the original purchaser of its Flip
Tip2 series nozzles (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from defects in material
and workmanship during the fi ve (5) year period from the date of purchase.
TFT’s obligation under this warranty is specifi cally limited to replacing or repairing the equipment (or its parts) which are shown by
TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the
equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA, within a reasonable time after discovery of the
defect. TFT will examine the equipment. If TFT determines that there is a defect attributable to it, TFT will correct the problem within
a reasonable time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is
an intended or unintended benefi ciary of the equipment, shall not be entitled to recover from TFT any consequential or incidental
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed
and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone
else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE.
THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.
This limited warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.