INSTALLATION INSTRUCTIONS
ZURICH 06-4001HS
ROMAN TUB FAUCET
TURN OFF
TURN OFF
SILICONE
Your installation may require
new supply lines.
(Supply lines are not included.)
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench Silicone caulk
2TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves.
These are usually found near water meter.
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
3DECK PREPARATION
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to 1-1/8” thick.
4INSTALL THE VALVE SYSTEM
Place a flange (1) on each housing assembly.
Thread each flange down until it locks onto
housing assembly.
5HANDLE INSTALLATION
Thread handle seat (1) onto flange (2) and secure with set screw (3). Install handle (4)
onto inverter (5) and secure with set screw (6). Insert the index (7).
Place the flange (1) onto the bottom of the
spout assembly (2). Place spout assembly
(2) through mounting hole in deck/rim.
From underneath the deck, secure spout
assembly with locknut (2) and washers (1).
Wrench tighten lock nut (2).
Thread T-tube (1) onto spout shank (2) until it
is completely seated.
7HOSE GUIDE INSTALLATION
Remove flange (1) from housing assembly. With the housing assembly marked “HOT” on
the left, adjust washers (1) and lock nut (2) to
the bottom of the housing assembly. Insert
the housing assembly through the mounting
holes from the underside of the deck/rim.
A B
C
6SPOUT INSTALLATION
A B
C
1
1
1
2
From underneath the deck secure housing
assembly with lock nut (3) and washers (2).
Wrench tighten locknut (3).
D
1
TORQUE
11 - 15 FT/LBS.
TORQUE
11 - 15 FT/LBS.
3
2
1
2
4
3
6
7
5
Insert hose guide (1) into deck hole. From underneath the deck, secure hose
guide with rubber washer (1), metal wash-
er (2) and locknut (3). Tighten locknut (3)
securely with wrench.
Connect the flexible water supply hose (1) to the bottom of valve bodies (2) as shown. Aligh T-tube (3)
in a position which will allow maximum clearance to connect hoses. Carefully bend the hoses to fit
available space. Carefully thread hose couplings to the sides of the T-tube (3).
A B
C
1
2
3
1
TORQUE
11 - 15 FT/LBS.
TORQUE
11 - 15 FT/LBS
11
3
2
2
TORQUE
11 - 15 FT/LBS
2
1
TORQUE
11-1 5 FT/LBS
1
2
TORQUE
11 - 15 FT/LBS.
Maximum distance between center of
spout and inside of bathtub is 4-11/16”
(119 mm). Refer to illustration above.
4-11/16”
(119 mm)
5” min. (127 mm)
3” min.
(76 mm)
8-16” (203-406 mm)
4-6” (102-152 mm)
ø1-1/8”
(29 mm)
ø1-3/8”
(35 mm)
ø1-3/8”
(35 mm)
ø1-3/8”
(35 mm)
1-1/8” (29 mm) MAX. DECK THICKNESS
